- 23 Apr, 2024 10 commits
-
-
Jianfeng Liu authored
Specification: Rockchip Rk3588 SoC 4x ARM Cortex-A76, 4x ARM Cortex-A55 8/16/32GB Memory LPDDR4/LPDDR4x Mali G610MP4 GPU 2× MIPI-CSI Connector 1× MIPI-DSI Connector 1x M.2 Key M (PCIe 3.0 4-lanes) 2x RTL8125 2.5G Ethernet Onboard AP6275P for WIFI6/BT5 32GB/64GB/128GB eMMC MicroSD card slot 1x USB2.0, 1x USB3.0 Type-A, 1x US3.0 Type-C 1x HDMI Output, 1x type-C DP Output Functions work normally: USB2.0 Host USB3.0 Type-A Host M.2 Key M (PCIe 3.0 4-lanes) 2x RTL8125 2.5G Ethernet eMMC MicroSD card More information can be obtained from the following website https://docs.armsom.org/armsom-sige7Signed-off-by:Jianfeng Liu <liujianfeng1994@gmail.com> Reviewed-by:
Weizhao Ouyang <weizhao.ouyang@arm.com> Link: https://lore.kernel.org/r/20240420034300.176920-4-liujianfeng1994@gmail.comSigned-off-by:
Heiko Stuebner <heiko@sntech.de>
-
Jianfeng Liu authored
Add devicetree binding for ArmSoM Sige7 board Signed-off-by:
Krzysztof Kozlowski <krzk@kernel.org> Reviewed-by:
-
Jianfeng Liu authored
Add vendor prefix for ArmSoM (https://www.armsom.org) Signed-off-by:
Conor Dooley <conor.dooley@microchip.com> Reviewed-by:
-
Heiko Stuebner authored
The Jaguar SBC provides an M.2 slot connected to the pcie3 controller. In contrast to a number of other boards the pcie-refclk is gpio-controlled, so the necessary clock and is added to the list of pcie3 clocks. Signed-off-by:
Heiko Stuebner <heiko.stuebner@cherry.de> Reviewed-by:
Quentin Schulz <quentin.schulz@theobroma-systems.com> Link: https://lore.kernel.org/r/20240423074956.2622318-1-heiko@sntech.deSigned-off-by:
-
Heiko Stuebner authored
The association of uart2 to the q7-uart pins is part of the module itself and not the baseboard used. Therefore move the pinctrl over to the tiger dtsi. Signed-off-by:
-
Chris Morgan authored
Add support for the USB-C port on the Indiedroid Nova board. This port supports USB-C DP Alt mode (not implemented yet in drivers), but works as a USB XHCI/EHCI/OHCI port. Signed-off-by:
Chris Morgan <macromorgan@hotmail.com> Link: https://lore.kernel.org/r/20240418173627.1368494-1-macroalpha82@gmail.comSigned-off-by:
-
Chukun Pan authored
According to https://radxa.com/products/rock3/3a, the name of this board should be "Radxa ROCK 3A". Suggested-by:
FUKAUMI Naoki <naoki@radxa.com> Signed-off-by:
Chukun Pan <amadeus@jmu.edu.cn> Reviewed-by:
Dragan Simic <dsimic@manjaro.org> Link: https://lore.kernel.org/r/20240419103019.992586-3-amadeus@jmu.edu.cnSigned-off-by:
-
Chukun Pan authored
According to https://radxa.com/products/rock3/3a, the name of this board should be "Radxa ROCK 3A". Suggested-by:
Rob Herring (Arm) <robh@kernel.org> Link: https://lore.kernel.org/r/20240419103019.992586-2-amadeus@jmu.edu.cnSigned-off-by:
-
Dragan Simic authored
Correct the descriptions of a few Radxa boards, according to the up-to-date documentation from Radxa and the detailed explanation from Naoki. [1] To sum it up, the short naming, as specified by Radxa, is preferred. [1] https://lore.kernel.org/linux-rockchip/B26C732A4DCEA9B3+282b8775-601b-4d4a-a513-4924b7940076@radxa.com/Suggested-by:
-
Dragan Simic authored
Correct the descriptions of a few Radxa boards, according to the up-to-date documentation from Radxa and the detailed explanation from Naoki. [1] To sum it up, the short naming, as specified by Radxa, is preferred. [1] https://lore.kernel.org/linux-rockchip/B26C732A4DCEA9B3+282b8775-601b-4d4a-a513-4924b7940076@radxa.com/Suggested-by:
-
- 12 Apr, 2024 7 commits
-
-
Sebastian Reichel authored
Enable full support (XHCI, EHCI, OHCI) for the lower USB3 port from Radxa Rock 5 Model B. The upper one is already supported. Signed-off-by:
Sebastian Reichel <sebastian.reichel@collabora.com> Link: https://lore.kernel.org/r/20240408225109.128953-11-sebastian.reichel@collabora.comSigned-off-by:
-
Sebastian Reichel authored
Enable full support (XHCI, EHCI, OHCI) for the upper USB3 port from Radxa Rock 5 Model A. The lower one is already supported. Signed-off-by:
-
Sebastian Reichel authored
Add support for the board's USB3 connectors. It has 1x USB Type-A and 1x USB Type-C. Signed-off-by:
-
Sebastian Reichel authored
Add both USB3 dual-role controllers to the RK3588 devicetree. Signed-off-by:
-
Sebastian Reichel authored
Add both USB3-DisplayPort PHYs to RK3588 SoC DT. Signed-off-by:
-
Sebastian Reichel authored
Reorder common DT properties alphabetically for usb2phy, according to latest DT style rules. Signed-off-by:
-
Sebastian Reichel authored
usb2-phy should be named usb2phy according to the DT binding, so let's fix it up accordingly. Signed-off-by:
-
- 11 Apr, 2024 2 commits
-
-
Muhammed Efe Cetin authored
Khadas Edge 2 has PT7C4363 RTC that compatible with HYM8563. The RTC pinctrl is also connected to MCU. Signed-off-by:
Muhammed Efe Cetin <efectn@protonmail.com> Link: https://lore.kernel.org/r/4c4c9140ff36f290ba64ecc8b3e218df6a5ab273.1708381247.git.efectn@protonmail.comSigned-off-by:
-
Muhammed Efe Cetin authored
Khadas Edge 2 has onboard AP6275P Wi-Fi6 (PCIe2) and BT5 (UART9) module. This commit enables UART9. Signed-off-by:
-
- 10 Apr, 2024 20 commits
-
-
Muhammed Efe Cetin authored
This commit adds SPI flash support for Khadas Edge 2. Signed-off-by:
-
Muhammed Efe Cetin authored
This commit enables tsadc, saradc and the function button on saradc line for Khadas Edge 2. Signed-off-by:
-
Muhammed Efe Cetin authored
Khadas Edge 2 exposes IR receiver pins as same as TF card via EXTIO. The IR receiver is connected to MCU and SoC. The board also has 2 PWM RGB leds. One is controlled by MCU and the other is controlled by SoC. This commit adds support for the led controlled by SoC using pwm-leds. Signed-off-by:
-
Muhammed Efe Cetin authored
Khadas Edge 2 has 1x USB2 with hub, 1x USB3 Host and 1x USB-C. This commit adds support for PCIe2, USB3 Host and USB2. Signed-off-by:
-
Muhammed Efe Cetin authored
Add TF card support to Khadas Edge 2. The board exposes sdmmc pins via EXTIO. TF card can be used with IO module. Signed-off-by:
-
Muhammed Efe Cetin authored
This commit adds PMIC to Khadas Edge 2 board. Signed-off-by:
-
Muhammed Efe Cetin authored
This commit adds 5V fixed power regulator and CPU regulators to Khadas Edge 2. Signed-off-by:
-
Chris Morgan authored
Add support for the GameForce Chi, which is a handheld gaming console from GameForce with a Rockchip RK3326 SoC. The device has a 640x480 3.5" dual-lane DSI display, one analog joystick connected to the SoC SARADC controller and a second analog joystick connected to an unknown UART based ADC, a single SD card slot, a single USB-C port for charging, and onboard RTL8723BS WiFi/Bluetooth combo, multiple face buttons, and an array of R/G/B LEDs used for key backlighting. The vendor was unable to provide details on the unknown UART based ADC which I have documented via a comment in the device-tree, and the vendor also does not have available Bluetooth firmware (the BT was not previously working on the vendor's OS, this has also been noted in a device-tree comment). Aside from the right analog ADC joystick and bluetooth all hardware has been tested and is working as expected. Signed-off-by:
-
Chris Morgan authored
The GameForce Chi is a handheld gaming device from GameForce powered by the Rockchip RK3326 SoC. Signed-off-by:
-
Chris Morgan authored
Some Powkiddy model names begin with the company "Powkiddy" and others simply list the model number. Make this consistent across the device lineup by including the manufacturer in the model name. Signed-off-by:
-
Chris Morgan authored
Add the optional node of chasis-type for Powkiddy RK3566 based devices. Signed-off-by:
-
Chris Morgan authored
Some Anbernic model names begin with the company "Anbernic" and others simply list the model number. Make this consistent across the device lineup by including the manufacturer in the model name. Signed-off-by:
-
Chris Morgan authored
Add optional node for chasis-type defining this device as a handset. Signed-off-by:
-
Chris Morgan authored
Add additional properties for the SDMMC2 node. Based on user feedback these help correct some issues with probing the WiFi hardware. Signed-off-by:
-
Dmitry Yashin authored
OK3588-C is the carrier board for FET3588-C System on Module. OK3588-C features: - 2x 1GbE Realtek RTL8211F Ethernet - 1x HDMI Type A out - 1x HDMI Type A in - 3x USB 3.1 Type C (2x OTG and 1x serial console) - 1x USB 2.0 Type A - 1x USB 3.0 & USB 2.0 Combo M.2 M Key (4G/5G modem) - 1x PCIE 2.0 M.2 E Key (1 lane) - 1x PCIE 2.0 PCIe (1 lane) - 1x PCIE 3.0 PCIe (4 lanes) - 1x TF scard slot - 5x MIPI CSI - 2x MIP DSI - 2x CAN2.0B - 1x RS485 - 1x NAU8822 onboard audio - 1x FAN connector - 1x RTC - 20-pin expansion header - ADC keys Add support for Forlinx OK3588-C board. Signed-off-by:
Dmitry Yashin <dmt.yashin@gmail.com> Link: https://lore.kernel.org/r/20240403151229.30577-4-dmt.yashin@gmail.comSigned-off-by:
-
Dmitry Yashin authored
FET3588-C is an System on Module made by Forlinx based on Rockchip RK3588. This SoM used by OK3588-C Board. FET3588-C features: - Rockchip RK3588 - LPDDR4 4/8 GB - eMMC 32/64 GB Add support for Forlinx FET3588-C SoM. Signed-off-by:
-
Dmitry Yashin authored
FET3588-C is an System on Module made by Forlinx based on Rockchip RK3588. This SoM used by OK3588-C Board. FET3588-C features: - Rockchip RK3588 - LPDDR4 4/8 GB - eMMC 32/64 GB Add devicetree binding for Forlinx FET3588-C SoM. Signed-off-by:
-
David Jander authored
MECSBC is a single board computer for blood analysis machines from RR-Mechatronics, designed and manufactured by Protonic Holland, based on the Rockchip RK3568 SoC. Signed-off-by:
David Jander <david@protonic.nl> Signed-off-by:
Sascha Hauer <s.hauer@pengutronix.de> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20240405-protonic-mecsbc-v2-2-0a6fedc78b9f@pengutronix.deSigned-off-by:
-
Sascha Hauer authored
MECSBC is a single board computer for blood analysis machines from RR-Mechatronics, designed and manufactured by Protonic Holland, based on the Rockchip RK3568 SoC. Acked-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by:
-
Diederik de Haas authored
Fix the ordering of the main nodes by sorting them alphabetically and then the ones with a memory address sequentially by that address. Signed-off-by:
Diederik de Haas <didi.debian@cknow.org> Link: https://lore.kernel.org/r/20240406172821.34173-1-didi.debian@cknow.orgSigned-off-by:
-
- 01 Apr, 2024 1 commit
-
-
Folker Schwesinger authored
Commit 8b5c2b45 disabled the internal pull-down for the strobe line causing I/O errors in HS400 mode for various eMMC modules. Enable the internal strobe pull-down for the ROCK 4C+ board. Also re-enable HS400 mode, that was replaced with HS200 mode as a workaround for the stability issues in: 2bd1d2dd ("arm64: dts: rockchip: Disable HS400 for eMMC on ROCK 4C+"). Fixes: 8b5c2b45 ("phy: rockchip: set pulldown for strobe line in dts") Signed-off-by:
Folker Schwesinger <dev@folker-schwesinger.de> Reviewed-by:
-
