- 28 Nov, 2022 4 commits
-
-
Ji-Pin Jou authored
For SDIO/USB interface, since the tranferring speed is slower than that in PCIE, it may have race condition when the driver sets down H2C command to the FW. In the function rtw_fw_send_h2c_command, before the patch, box_reg is written first, then box_ex_reg is written. FW starts to work and fetch the value of box_ex_reg, when the most significant byte of box_reg(4 bytes) is written. Meanwhile, for SDIO/USB interface, since the transferring speed is slow, the driver is still in writing the new value of box_ex_reg through the bus, and FW may get the wrong value of box_ex_reg at the moment. To prevent the above driver/FW racing situation, box_ex_reg is written first then box_reg. Furthermore, it is written in 4 bytes at a time, instead of written in one byte one by one. It can increase the speed for SDIO/USB interface. Signed-off-by:
Ji-Pin Jou <neo_jou@realtek.com> Signed-off-by:
Ping-Ke Shih <pkshih@realtek.com> Tested-by:
Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by:
Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20221124064442.28042-1-pkshih@realtek.com
-
Lukas Bulwahn authored
Commit 399500da ("ssb: pick PCMCIA host code support from b43 driver") removes the config B43_PCMCIA. Clean up the last reference to this removed config B43_PCMCIA in the b43_print_driverinfo() function. Signed-off-by:
Lukas Bulwahn <lukas.bulwahn@gmail.com> Signed-off-by:
-
Bitterblue Smith authored
Commit a8b5aef2 ("wifi: rtl8xxxu: gen2: Enable 40 MHz channel width") introduced a line where the pointer returned by ieee80211_find_sta() is used after rcu_read_unlock(). Move rcu_read_unlock() a bit lower to fix this. Fixes: a8b5aef2 ("wifi: rtl8xxxu: gen2: Enable 40 MHz channel width") Signed-off-by:
Bitterblue Smith <rtl8821cerfe2@gmail.com> Reviewed-by:
-
Ziyang Xuan authored
urbs does not be freed in exception paths in __lf_x_usb_enable_rx(). That will trigger memory leak. To fix it, add kfree() for urbs within "error" label. Compile tested only. Fixes: 68d57a07 ("wireless: add plfxlc driver for pureLiFi X, XL, XC devices") Signed-off-by:
Ziyang Xuan <william.xuanziyang@huawei.com> Signed-off-by:
-
- 22 Nov, 2022 10 commits
-
-
Kees Cook authored
Zero-length arrays are deprecated[1] and are being replaced with flexible array members in support of the ongoing efforts to tighten the FORTIFY_SOURCE routines on memcpy(), correctly instrument array indexing with UBSAN_BOUNDS, and to globally enable -fstrict-flex-arrays=3. Replace zero-length array with flexible-array member. This results in no differences in binary output (most especially because struct pda_antenna_gain is unused). The struct is kept for future reference. [1] https://github.com/KSPP/linux/issues/78 Cc: Christian Lamparter <chunkeey@googlemail.com> Cc: Kalle Valo <kvalo@kernel.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: Eric Dumazet <edumazet@google.com> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Paolo Abeni <pabeni@redhat.com> Cc: "Gustavo A. R. Silva" <gustavoars@kernel.org> Cc: linux-wireless@vger.kernel.org Cc: netdev@vger.kernel.org Signed-off-by:
Kees Cook <keescook@chromium.org> Acked-by:
Christian Lamparter <chunkeey@gmail.com> Signed-off-by:
-
Zong-Zhe Yang authored
The index RTW89_PHYSTS_BITMAP_NUM is not a valid physts IE page. So, fix the check condition. Fixes: eb4e52b3 ("rtw89: fix incorrect channel info during scan") Signed-off-by:
Zong-Zhe Yang <kevin_yang@realtek.com> Signed-off-by:
-
Ping-Ke Shih authored
During doing change_interface(), hardware is power-off, so some components are inaccessible and return error. This causes things unexpected, and we don't have a warning message for that. So, ignore some IO operations in this situation, and add a warning message to indicate something wrong. Signed-off-by:
-
Eric Huang authored
There are some registers for transmit waveform control, two of them used in this change are for BANDEDGE and TX_SHAPE control. BANDEDGE controls whether to apply band edge filter to transmit waveform. TX_SHAPE controls whether to apply triangular mask to transmit waveform. It is found for some chip, these two should be turned off during OFDMA UL traffic for better performance. Signed-off-by:
Eric Huang <echuang@realtek.com> Signed-off-by:
-
Eric Huang authored
Add macro to get FD(frequency domain) CFO field from ie_type 1, and correct the naming for preamble CFO field. Each IC could assign the CFO source to either FD CFO or preamble CFO in chip_info. Based on the suggestion from HW designer, rtw8852b and its derived versions will have better CFO tracking performance with FD CFO. Signed-off-by:
-
Ping-Ke Shih authored
When coexistence mechanism is under free-run mode, it could adjust WiFi and BT TX power to avoid interference with each other. For other cases, it should keep original TX power from regular predefined tables, so set correct values to 255 for these cases. Signed-off-by:
-
Gustavo A. R. Silva authored
Prefer struct_size() over open-coded versions of idiom: sizeof(struct-with-flex-array) + sizeof(typeof-flex-array-elements) * count where count is the max number of items the flexible array is supposed to contain. In this particular case, in the open-coded version sizeof(typeof-flex-array-elements) is implicit in _count_ because the type of the flex array data is u8: drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwil_types.h:941: 941 struct brcmf_dload_data_le { 942 __le16 flag; 943 __le16 dload_type; 944 __le32 len; 945 __le32 crc; 946 u8 data[]; 947 }; Link: https://github.com/KSPP/linux/issues/160Signed-off-by:Gustavo A. R. Silva <gustavoars@kernel.org> Reviewed-by:
-
Gustavo A. R. Silva authored
One-element arrays are deprecated, and we are replacing them with flexible array members instead. So, replace one-element array with flexible-array member in struct brcmf_dload_data_le. Important to mention is that doing a build before/after this patch results in no binary output differences. This helps with the ongoing efforts to tighten the FORTIFY_SOURCE routines on memcpy() and help us make progress towards globally enabling -fstrict-flex-arrays=3 [1]. Link: https://github.com/KSPP/linux/issues/230 Link: https://github.com/KSPP/linux/issues/79 Link: https://gcc.gnu.org/pipermail/gcc-patches/2022-October/602902.html [1] Signed-off-by:
-
Gustavo A. R. Silva authored
Prefer struct_size() over open-coded versions of idiom: sizeof(struct-with-flex-array) + sizeof(typeof-flex-array-elements) * count where count is the max number of items the flexible array is supposed to contain. Also, use array_size() in call to memcpy(). Link: https://github.com/KSPP/linux/issues/160Signed-off-by:
-
Gustavo A. R. Silva authored
One-element arrays are deprecated, and we are replacing them with flexible array members instead. So, replace one-element array with flexible-array member in struct brcmf_gscan_config. Important to mention is that doing a build before/after this patch results in no binary output differences. This helps with the ongoing efforts to tighten the FORTIFY_SOURCE routines on memcpy() and help us make progress towards globally enabling -fstrict-flex-arrays=3 [1]. Link: https://github.com/KSPP/linux/issues/79 Link: https://github.com/KSPP/linux/issues/241 Link: https://gcc.gnu.org/pipermail/gcc-patches/2022-October/602902.html [1] Signed-off-by:
-
- 18 Nov, 2022 26 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fsDavid S. Miller authored
David Howells says: ==================== rxrpc: Fix oops and missing config conditionals The patches that were pulled into net-next previously[1] had some issues that this patchset fixes: (1) Fix missing IPV6 config conditionals. (2) Fix an oops caused by calling udpv6_sendmsg() directly on an AF_INET socket. (3) Fix the validation of network addresses on entry to socket functions so that we don't allow an AF_INET6 address if we've selected an AF_INET transport socket. Link: https://lore.kernel.org/r/166794587113.2389296.16484814996876530222.stgit@warthog.procyon.org.uk/ [1] ==================== Signed-off-by:David S. Miller <davem@davemloft.net>
-
Eric Dumazet authored
Dan reported a new warning after my recent patch: New smatch warnings: net/core/dev.c:6409 napi_disable() error: uninitialized symbol 'new'. Indeed, we must first wait for STATE_SCHED and STATE_NPSVC to be cleared, to make sure @new variable has been initialized properly. Fixes: 4ffa1d1c ("net: adopt try_cmpxchg() in napi_{enable|disable}()") Reported-by:
kernel test robot <lkp@intel.com> Reported-by:
Dan Carpenter <error27@gmail.com> Signed-off-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Dan Carpenter authored
The "pkt" was supposed to have been deleted in a previous patch. It leads to an uninitialized variable bug. Fixes: 72f0c6fb ("rxrpc: Allocate ACK records at proposal and queue for transmission") Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Acked-by:
David Howells <dhowells@redhat.com> Signed-off-by:
-
Dan Carpenter authored
The error handling for if skb_copy_bits() fails was accidentally deleted so the rxkad_decrypt_ticket() function is not called. Fixes: 5d7edbc9 ("rxrpc: Get rid of the Rx ring") Signed-off-by:
-
Lorenzo Bianconi authored
Get rid of cpu_relax in mtk_pending_work routine since MTK_RESETTING is set only in mtk_pending_work() and it runs holding rtnl lock Signed-off-by:
Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by:
-
Lorenzo Bianconi authored
Restore user configured MTU running mtk_hw_init() during tx timeout routine since it will be overwritten after a hw reset. Reported-by:
Felix Fietkau <nbd@nbd.name> Fixes: 9ea4d311 ("net: ethernet: mediatek: add the whole ethernet reset into the reset process") Signed-off-by:
-
Alex Elder authored
Dan Carpenter reported that Smatch found an instance where a pointer which had previously been assumed could be null (as indicated by a null check) was later dereferenced without a similar check. In practice this doesn't lead to a problem because currently the pointers used are all non-null. Nevertheless this patch addresses the reported problem. In addition, I spotted another bug that arose in the same commit. When the command to initialize a routing table memory region was added, the number of entries computed for the non-hashed table was wrong (it ended up being a Boolean rather than the count intended). This bug is fixed here as well. Reported-by:
Caleb Connolly <caleb.connolly@linaro.com> Fixes: 5cb76899 ("net: ipa: reduce arguments to ipa_table_init_add()") Signed-off-by:
Alex Elder <elder@linaro.org> Signed-off-by:
-
David S. Miller authored
Merge tag 'wireless-next-2022-11-18' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next Kalle Valo says: ==================== wireless-next patches for v6.2 Second set of patches for v6.2. Only driver patches this time, nothing really special. Unused platform data support was removed from wl1251 and rtw89 got WoWLAN support. Major changes: ath11k * support configuring channel dwell time during scan rtw89 * new dynamic header firmware format support * Wake-over-WLAN support rtl8xxxu * enable IEEE80211_HW_SUPPORT_FAST_XMIT ==================== Signed-off-by:
-
David S. Miller authored
Xin Long says: ==================== sctp: support vrf processing This patchset adds the VRF processing in SCTP. Simliar to TCP/UDP, it includes socket bind and socket/association lookup changes. For socket bind change, it allows sockets to bind to a VRF device and allows multiple sockets with the same IP and PORT to bind to different interfaces in patch 1-3. For socket/association lookup change, it adds dif and sdif check in both asoc and ep lookup in patch 4 and 5, and when binding to nodev, users can decide if accept the packets received from one l3mdev by setup a sysctl option in patch 6. Note with VRF support, in a netns, an association will be decided by src ip + src port + dst ip + dst port + bound_dev_if, and it's possible for ss to have: State Local Address:Port Peer Address:Port ESTAB 192.168.1.2%vrf-s1:1234 `- ESTAB 192.168.1.2%veth1:1234 192.168.1.1:1234 ESTAB 192.168.1.2%vrf-s2:1234 `- ESTAB 192.168.1.2%veth2:1234 192.168.1.1:1234 See the selftest in patch 7 for more usage. Also, thanks Carlo for testing this patch series on their use. v1->v2: - In Patch 5, move sctp_sk_bound_dev_eq() definition to net/sctp/ input.c to avoid a build error when IP_SCTP is disabled, as Paolo suggested. - In Patch 7, avoid one sleep by disabling the IPv6 dad, and remove another sleep by using ss to check if the server's ready, and also delete two unncessary sleeps in sctp_hello.c, as Paolo suggested. ==================== Signed-off-by: -
Xin Long authored
This patch adds 12 small test cases: 01-04 test for the sysctl net.sctp.l3mdev_accept. 05-10 test for only binding to a right l3mdev device, the connection can be created. 11-12 test for two socks binding to different l3mdev devices at the same time, each of them can process the packets from the corresponding peer. The tests run for both IPv4 and IPv6 SCTP. Signed-off-by:
Xin Long <lucien.xin@gmail.com> Signed-off-by:
-
Xin Long authored
This patch is to add sysctl net.sctp.l3mdev_accept to allow users to change the pernet global l3mdev_accept. Signed-off-by:
-
Xin Long authored
This patch at first adds a pernet global l3mdev_accept to decide if it accepts the packets from a l3mdev when a SCTP socket doesn't bind to any interface. It's set to 1 to avoid any possible incompatible issue, and in next patch, a sysctl will be introduced to allow to change it. Then similar to inet/udp_sk_bound_dev_eq(), sctp_sk_bound_dev_eq() is added to check either dif or sdif is equal to sk_bound_dev_if, and to check sid is 0 or l3mdev_accept is 1 if sk_bound_dev_if is not set. This function is used to match a association or a endpoint, namely called by sctp_addrs_lookup_transport() and sctp_endpoint_is_match(). All functions that needs updating are: sctp_rcv(): asoc: __sctp_rcv_lookup() __sctp_lookup_association() -> sctp_addrs_lookup_transport() __sctp_rcv_lookup_harder() __sctp_rcv_init_lookup() __sctp_lookup_association() -> sctp_addrs_lookup_transport() __sctp_rcv_walk_lookup() __sctp_rcv_asconf_lookup() __sctp_lookup_association() -> sctp_addrs_lookup_transport() ep: __sctp_rcv_lookup_endpoint() -> sctp_endpoint_is_match() sctp_connect(): sctp_endpoint_is_peeled_off() __sctp_lookup_association() sctp_has_association() sctp_lookup_association() __sctp_lookup_association() -> sctp_addrs_lookup_transport() sctp_diag_dump_one(): sctp_transport_lookup_process() -> sctp_addrs_lookup_transport() Signed-off-by: -
Xin Long authored
Add skb_sdif function in struct sctp_af to get the enslaved device for both ipv4 and ipv6 when adding SCTP VRF support in sctp_rcv in the next patch. Signed-off-by:
-
Xin Long authored
In sctp_get_port_local(), when binding to IP and PORT, it should also check sk_bound_dev_if to match listening sk if it's set by SO_BINDTOIFINDEX, so that multiple sockets with the same IP and PORT, but different sk_bound_dev_if can be listened at the same time. Signed-off-by:
-
Xin Long authored
When binding to an ipv6 address, it calls ipv6_chk_addr() to check if this address is on any dev. If a socket binds to a l3mdev but no dev is passed to do this check, all l3mdev and slaves will be skipped and the check will fail. This patch is to pass the bound_dev to make sure the devices under the same l3mdev can be returned in ipv6_chk_addr(). When the bound_dev is not a l3mdev or l3slave, l3mdev_master_dev_rcu() will return NULL in __ipv6_chk_addr_and_flags(), it will keep compitable with before when NULL dev was passed. Signed-off-by:
-
Xin Long authored
After binding to a l3mdev, it should use the route table from the corresponding VRF to verify the addr when binding to an address. Note ipv6 doesn't need it, as binding to ipv6 address does not verify the addr with route lookup. Signed-off-by:
-
Jiawen Wu authored
Fix duplicate check on polling timeout. Fixes: 1efa9bfe ("net: libwx: Implement interaction with firmware") Signed-off-by:
Jiawen Wu <jiawenwu@trustnetic.com> Reviewed-by:
Leon Romanovsky <leonro@nvidia.com> Signed-off-by:
-
Antoine Tenart authored
Following 1b16b3fd ("net: phy: mscc: macsec: clear encryption keys when freeing a flow"), go one step further and instead of calling memzero_explicit on the key when freeing a flow, simply not copy the key in the first place as it's only used when a new flow is set up. Signed-off-by:
Antoine Tenart <atenart@kernel.org> Signed-off-by:
-
Jakub Kicinski authored
Alex Elder says: ==================== net: ipa: change GSI firmware load specification Currently, GSI firmware must be loaded for IPA before it can be used--either by the modem, or by the AP. New hardware supports a third option, with the bootloader taking responsibility for loading GSI firmware. In that case, neither the AP nor the modem needs to do that. The first patch in this series deprecates the "modem-init" Device Tree property in the IPA binding, using a new "qcom,gsi-loader" property instead. The second and third implement logic in the code to support either the "old" or the "new" way of specifying how GSI firmware is loaded. The last two patches implement a new value for the "qcom,gsi-loader" property. If the value is "skip", neither the AP nor modem needs to load the GSI firmware. The first of these patches implements the change in the IPA binding; the second implements it in the code. ==================== Link: https://lore.kernel.org/r/20221116073257.34010-1-elder@linaro.orgSigned-off-by:
Jakub Kicinski <kuba@kernel.org>
-
Alex Elder authored
Define a new value "skip" for the "qcom,gsi-loader" Device Tree property. If used, it indicates that neither the AP nor the modem need to load GSI firmware (because it has already been loaded--for example by the boot loader). Signed-off-by:
-
Alex Elder authored
Add a new enumerated value to those defined for the qcom,gsi-loader property. If the qcom,gsi-loader is "skip", the GSI firmware will already be loaded, so neither the AP nor modem is required to load GSI firmware. Signed-off-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by:
-
Alex Elder authored
Introduce a new way of specifying how the GSI firmware gets loaded for IPA. Currently, this is indicated by the presence or absence of the Boolean "modem-init" Device Tree property. The new property must have a value--either "self" or "modem"--which indicates whether the AP or modem is the GSI firmware loader, respectively. For legacy systems, the new property will not exist, and the "modem-init" property will be used. For newer systems, the "qcom,gsi-loader" property *must* exist, and must have one of the two prescribed values. It is an error to have both properties defined, and it is an error for the new property to have an unrecognized value. Signed-off-by:
-
Alex Elder authored
The GSI layer used for IPA requires firmware to be loaded. Currently either the AP or the modem loads the firmware, distinguished by whether the "modem-init" Device Tree property is defined. Some newer systems implement a third option. In preparation for that, encapsulate the code that determines how the GSI firmware gets loaded in a new function, ipa_firmware_loader(). Signed-off-by:
-
Alex Elder authored
GSI firmware for IPA must be loaded during initialization, either by the AP or by the modem. The loader is currently specified based on whether the Boolean modem-init property is present. Instead, use a new property with an enumerated value to indicate explicitly how GSI firmware gets loaded. With this in place, a third approach can be added in an upcoming patch. The new qcom,gsi-loader property has two defined values: - self: The AP loads GSI firmware - modem: The modem loads GSI firmware The modem-init property must still be supported, but is now marked deprecated. Update the example so it represents the SC7180 SoC, and provide examples for the qcom,gsi-loader, memory-region, and firmware-name properties. Signed-off-by:
-
Xin Long authored
Move these two macros from net/sctp/sctp.h to linux/sctp.h, so that it will be enough to include only linux/sctp.h in nft_exthdr.c and xt_sctp.c. It should not include "net/sctp/sctp.h" if a module does not have a dependence on SCTP module. Signed-off-by:
Saeed Mahameed <saeed@kernel.org> Link: https://lore.kernel.org/r/ef6468a687f36da06f575c2131cd4612f6b7be88.1668526821.git.lucien.xin@gmail.comSigned-off-by:
-
Xin Long authored
Currently "net/sctp/checksum.h" including "net/sctp/sctp.h" is included in quite some places in netfilter and openswitch and net/sched. It's not necessary to include "net/sctp/sctp.h" if a module does not have dependence on SCTP, "linux/sctp.h" is the right one to include. Signed-off-by:
-
