Prepare the driver for the addition of chip variants with a different number of
channels. This is done by not hard-coding the number of channels, but instead
add a field to the chip info struct holding the number of channels. Also do not
embed the channel specs into the chip info, but rather store them independently.
This allows sharing the same channel spec between different chip infos.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use extended channel info attributes for the powerdown, powerdown_mode and
powerdown_mode_available attributes.

Note that this patch moves the chip info defintion around to avoid having to use
forward declarations for the extended channel info attributes callbacks.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Sometimes devices have per channel properties which either do not map nicely to
the current channel info scheme (e.g. string properties) or are very device
specific, so it does not make sense to add generic support for them.

Currently drivers define these attributes by hand for each channel. Depending on
the number of channels this can amount to quite a few lines of boilerplate code.
Especially if a driver supports multiple variations of a chip with different
numbers of channels. In this case it becomes necessary to have a individual
attribute list per chip variation and also a individual iio_info struct.

This patch introduces a new scheme for handling such per channel attributes
called extended channel info attributes. A extended channel info attribute
consist of a name, a flag whether it is shared and read and write callbacks.
The read and write callbacks are similar to the {read,write}_raw callbacks and
take a IIO device and a channel as their first parameters, but instead of
pre-parsed integer values they directly get passed the raw string value, which
has been written to the sysfs file.

It is possible to assign a list of extended channel info attributes to a
channel. For each extended channel info attribute the IIO core will create a new
sysfs attribute conforming to the IIO channel naming spec for the channels type,
similar as for normal info attributes. Read and write access to this sysfs
attribute will be redirected to the extended channel info attributes read and
write callbacks.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Convert the IIO drivers which have not been converted yet to module_spi_driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use dev_pm_ops instead of legacy suspend/resume callbacks for IIO drivers.

Note that this patch introduces a few new #ifdef CONFIG_PM_SLEEP around the
suspend and resume callbacks to avoid warnings of unused functions if
CONFIG_PM_SLEEP is not defined.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Very basic description of the way iio consumers work and how to use
this functionality.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Direct copy of version proposed for the non staging branch.
Needed here to allow testing of more advanced inkernel
interface code.

Minimal support of simple in, curr and temp attributes
so far.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In kernel interfaces need these, so make them available.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Lifted from proposal for in kernel interface built on the out of staging
branch.

Two elements here:
* Map as defined in "inkern.h"
* Matching code to actually get the iio_dev and channel
that we want from the global list of IIO devices.
V4: Everything now built if iio is built (rather than being optional)
    Removal race condition prevented by using info pointer as a check
    of removal under a lock.
V3: Drop the option of registering / getting channels using dev pointer.
Stick to name only as suggested by Mark Brown (this has caused user
confusion in the regulator framework.)
V2: As per Greg KH suggestion, move over to registration by passing
the tables into the provider drivers (how regulator does it).
This does not prevent us using the original more flexible approach
if at a later date there is a usecase that demands it.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This prevents use of provider callbacks after it has been unregistered.
Note that all code using this that can be called from a consumer *must*
check the pointer before using and hold the info_exist_lock throughout
the usage of the callbacks in info.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In order to detect WDT feature on the dsp code, we need to
find the symbol used to enable it inside the baseimage.

This should fix the warning comming from L3 driver:

    WARNING: at arch/arm/mach-omap2/omap_l3_smx.c:161 omap3_l3_app_irq...
    In-band Error seen by IVA_SS  at address 0
    ...

That occurs because the dsp tries to access wdt3 registers when the clock
for those registers is not enabled.
Reported-by: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: Omar Ramirez Luna <omar.ramirez@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In order to detect it at runtime, we need the code handling wdt
clock available at runtime to decide whether to enable or disable
based on the baseimage symbols. Default timeout has been set to 5
seconds.

Downside is that we will lose the option to set a custom timeout
for overflow, but than can be added (if needed) as part of debugfs.
Signed-off-by: Omar Ramirez <omar.ramirez@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Correct spelling "erorr" to "error" in
drivers/stating/comedi/drivers/unioxx5.c
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Correct spelling "scaning" to "scanning" in
drivers/staging/vt6656/bssdb.c
drivers/staging/vt6655/bssdb.c
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit d6c25be (mdio-octeon: use an unique MDIO bus name.) changed the
names used to refer to MDIO buses.  The ethernet driver must be
changed to match, so that the PHY drivers can be attached.
Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Florian Fainelli <florian@openwrt.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The readers list is traversed under the log->mutex lock
(for example from fix_up_readers()), but the deletion of
elements from this list is not being done under this lock.

Cc: Brian Swetland <swetland@google.com>
Cc: Dima Zavin <dima@android.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

These are each >20k LOC drivers that embed an entire SD stack, and present
SD cards as if they were SCSI devices; both drivers should be rewritten to
be small hooks that connect the PCI (for rts_pstor) or USB (for rts5139)
hardware into Linux's MMC/xD/memorystick stacks.
Signed-off-by: Chris Ball <cjb@laptop.org>
Cc: edwin_rong <edwin_rong@realsil.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

p80211item_pstr6_t is the size of "msg1.bssid" (16 bytes) but
msg1.bssid.data is type p80211pstr6_t and it is smaller (7 bytes).  We
had just set that memory to zeroes earlier and now we're writing over it
with 0xff because we're writing past the end of the struct.

I don't know if this actually causes a problem.  It may be that we
initialize the extra 0xff bytes correctly later.  But the current code
is obviously wrong and we should fix it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Unify return value of .ndo_set_mac_address if the given address
isn't valid. Return -EADDRNOTAVAIL as eth_mac_addr() already does
if is_valid_ether_addr() fails.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This is a patch to the alphatrack.c and tranzport.c  that fixes up an error
found by checkpatch.pl tool.
Signed-off-by: Hitoshi Nakamori <hitoshi.nakamori@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The below patch fixes some comments with typos in the them and makes a comment make more sense.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit 9256a478 fixed a deadlock condition, being sure that the buddy
list spinlock is always taken before the page spinlock.

However in zbud_free_and_delist() locking order is the opposite
(page lock -> list lock).

Possible unsafe locking scenario (reported by lockdep):

        CPU0                    CPU1
        ----                    ----
   lock(&(&zbpg->lock)->rlock);
                                lock(zbud_budlists_spinlock);
                                lock(&(&zbpg->lock)->rlock);
   lock(zbud_budlists_spinlock);

Fix by grabbing the locks in opposite order in zbud_free_and_delist().
Signed-off-by: Andrea Righi <andrea@betterlinux.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

netif_rx is meant to be called from interrupts because it doesn't wake
up ksoftirqd.  For calling from outside interrupts, netif_rx_ni exists.

This stops the error "NOHZ: local_softirq_panding 08" that happens on
some machines with NOHZ and plip --- it is caused by the fact that
softirq is pending and ksoftirqd is sleeping.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Ramster can't be a module (yet) and depends on CONFIGFS_FS=y, but
allmodconfig builds with CONFIGFS_FS=m, which breaks the build.
And forcing CONFIGFS_FS=y with select breaks the build in other ways.
So just don't build ramster unless CONFIGFS_FS=y.

Also, while we're here, add a comment as to why BROKEN is depended.
Signed-off-by: Dan Magenheimer <dan.magenheimer@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Due to some conflicting debug vars, kernel build will warn when
CONFIG_RAMSTER=y and CONFIG_OCFS2=m and will fail when
CONFIG_RAMSTER=y and CONFIG_OCFS2=y (rare).

Rename ramster mlog vars to avoid the name conflict.
Signed-off-by: Dan Magenheimer <dan.magenheimer@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

New kernel developer inspired by the 2010 FOSDEM talk. Running checkpatch on
p80211netdev.c gave the error: p80211netdev.c:153: ERROR: "foo * bar" should
be "foo *bar". Fixed it by doing what was suggested.
Signed-off-by: Sebastiaan de Haan <sebastiaan@sebastiaandehaan.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove commented code of old style lock initilization
Signed-off-by: Santosh Nayak <santoshprasadnayak@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch eliminates following type of warnings
warning: no previous prototype for '...func...' [-Wmissing-prototypes]

For this is a single file example lets make all API-like functions
be static.
Since all static functions should be used so let's call
to amt_host_if_deinit() even if in this example it's not really necessary
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Looks during cleanup we converted type of host_version_supported
member from UINT8 into int instead of u8.
Since we've queried only for boolean value of
this variable the bug wasn't really visible.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Variable psfLocalSet may not follow the correct
path in the code, and therefore may not be set
properly. As such, causing a null dereference.
Signed-off-by: Kevin McKinney <klmckinney1@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The BCMLOG_ENTER macro is used only in five functions, perhaps
it is remainder of debugging some specific problem,
now, this macro don't seems to be useful, so it should be removed.
Signed-off-by: Jorgyano Vieira <jorgyano@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The BCMLOG_LEAVE macro is not used, so there is no reason to keep it.
Signed-off-by: Jorgyano Vieira <jorgyano@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Added Kconfig and Kbuild files for ozwpan USB over WiFi driver.
Modified parent Makefile and Kconfig to include them.
Signed-off-by: Chris Kelly <ckelly@ozmodevices.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Added tracing facilities and also memory allocation and URB tracking.
This is for debugging purposes and is all optional and can be switched
out at compile time.
Signed-off-by: Chris Kelly <ckelly@ozmodevices.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The event logging subsystem allows internal events in the driver to
be logged. This facilitates testing the correct operation of the
driver. This subsystem is optional and can be switched out at
compile time.
Signed-off-by: Chris Kelly <ckelly@ozmodevices.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The character device provides a management interface to the driver
and also provides an additional service to the protocol for side
band communication with the device.
Signed-off-by: Chris Kelly <ckelly@ozmodevices.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The L2 protocol supports various services, one of which is USB.
This provides the implementation of that service and plumbs it to
the virtual USB HCD.
Signed-off-by: Chris Kelly <ckelly@ozmodevices.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Added the implementation of the virtual USB HCD that is used to
present devices connected via the network to the USB subsystem.
Signed-off-by: Chris Kelly <ckelly@ozmodevices.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Added support for maintaining state and data buffering for devices
connected via the network.
Signed-off-by: Chris Kelly <ckelly@ozmodevices.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Added the basic implementation of the L2 protocol support used to
communicate with devices over the network.
Signed-off-by: Chris Kelly <ckelly@ozmodevices.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>