- 14 Dec, 2015 40 commits
-
-
Russell King authored
Add support for 32-bit register accesses to the AMBA PL011 UART. This is needed for ZTE UARTs, which require 32-bit accesses as opposed to the more normal 16-bit accesses. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Reviewed-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Russell King authored
Remove the ST micro registers from the standard table. These registers should never be accessed in non-ST micro variants. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Reviewed-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Russell King authored
As we can detect when the LCR register is split between TX and RX, we don't need three entries in the table to deal with this. Reduce this down to two entries by converting the REG_ST_LCRH_* entries to standard REG_LCRH_* and remove REG_LCRH. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Reviewed-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Russell King authored
Add the ST variant register offset table to the driver. Currently, this is an identical copy of the standard version, but this will be modified in the following changes. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Reviewed-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Russell King authored
Add the register offset table to the vendor data, allowing vendor differences to be described in this table. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Reviewed-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Russell King authored
Add a register lookup table, which allows the register offsets to be adjusted on a per-port basis. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Reviewed-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Peter Hurley authored
Instead of compare-and-set, just compute 'found'. Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Peter Hurley authored
Add a temporary for the computed source address and substitute where appropriate. No functional change. Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Peter Hurley authored
Merge the multiple tty_copy_to_user() calls into a single copy sequence within tty_copy_to_user(). Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Arnd Bergmann authored
As the of-serial driver is now 8250 specific, we can move the file to a more appropriate place in teh 8250 subdirectory and adapt the Kconfig help text and file name. I'm leaving the CONFIG_SERIAL_OF_PLATFORM symbol unchanged to avoid breaking user configuration files unnecessarily. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Arnd Bergmann authored
The only other user of this code was the nwp-serial driver, but that is now gone, so we can remove a couple of #ifdef statments in this driver. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Arnd Bergmann authored
The NWP serial driver is no longer needed, as the two users of this hardware have migrated to a much faster generation hardware, see https://en.wikipedia.org/wiki/QPACE2 for the replacement. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Cc: Benjamin Krill <ben@codiert.org> Cc: linuxppc-dev@lists.ozlabs.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
DengChao authored
The bfin-uart code uses real time with struct timeval. This will cause problems on 32-bit architectures in 2038 when time_t overflows. Since the code just needs delta value of time, it is not necessary to record them in real time. This patch changes the code to use the monotonic time instead, replaces struct timeval and do_gettimeofday() with u64 and ktime_get_ns(). Signed-off-by: DengChao <chao.deng@linaro.org> Reviewed-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Geert Uytterhoeven authored
If NO_DMA=y: ERROR: "dma_unmap_sg" [drivers/tty/serial/mxs-auart.ko] undefined! ERROR: "dma_map_sg" [drivers/tty/serial/mxs-auart.ko] undefined! Add a dependency on HAS_DMA to fix this. Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Geert Uytterhoeven authored
If NO_DMA=y: ERROR: "dma_unmap_sg" [drivers/tty/serial/imx.ko] undefined! ERROR: "dma_map_sg" [drivers/tty/serial/imx.ko] undefined! Add a dependency on HAS_DMA to fix this. Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Geert Uytterhoeven authored
If NO_DMA=y: drivers/built-in.o: In function `atmel_release_rx_dma': atmel_serial.c:(.text+0x2502e): undefined reference to `dma_unmap_sg' drivers/built-in.o: In function `atmel_release_tx_dma': atmel_serial.c:(.text+0x25080): undefined reference to `dma_unmap_sg' drivers/built-in.o: In function `atmel_tx_dma': atmel_serial.c:(.text+0x2517a): undefined reference to `dma_sync_sg_for_cpu' drivers/built-in.o: In function `atmel_release_tx_pdc': atmel_serial.c:(.text+0x252e6): undefined reference to `dma_unmap_single' drivers/built-in.o: In function `atmel_prepare_tx_pdc': atmel_serial.c:(.text+0x2531a): undefined reference to `dma_map_single' drivers/built-in.o: In function `atmel_release_rx_pdc': atmel_serial.c:(.text+0x25362): undefined reference to `dma_unmap_single' drivers/built-in.o: In function `atmel_tx_pdc': atmel_serial.c:(.text+0x25722): undefined reference to `dma_sync_single_for_cpu' drivers/built-in.o: In function `atmel_rx_from_pdc': atmel_serial.c:(.text+0x2601a): undefined reference to `dma_sync_single_for_cpu' drivers/built-in.o: In function `atmel_rx_from_dma': atmel_serial.c:(.text+0x261b2): undefined reference to `dma_sync_sg_for_cpu' atmel_serial.c:(.text+0x26264): undefined reference to `dma_sync_sg_for_cpu' drivers/built-in.o: In function `atmel_prepare_rx_pdc': atmel_serial.c:(.text+0x262de): undefined reference to `dma_unmap_single' atmel_serial.c:(.text+0x26308): undefined reference to `dma_map_single' Add a dependency on HAS_DMA to fix this. Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Florian Achleitner authored
We found that our sc16is7xx on spi reported a TX fifo free space value (TXLVL_REG) of 255 ocassionally, which is obviously wrong, with a 64 byte fifo and caused a buffer overrun and a kernel crash. To trigger this, a large write to the tty is sufficient. The fifo fills, TXLVL_REG reads zero, but the handle_tx function does a zero-data-length write to the TX fifo anyways through sc16is7xx_fifo_write. The next TXLVL_REG read then yields 255, for unknown reasons. A subsequent read is ok. Prevent zero-data-length writes if the TX fifo is full, because they are pointless, and because they trigger wrong TXLVL read-outs. Furthermore, prevent a TX buffer overrun if the peripheral reports values larger than the buffer size and thus, don't allow the peripheral to crash the kernel. Signed-off-by: Florian Achleitner <achleitner.florian@fronius.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Peter Hurley authored
Perform common exit for both successful and error exit handling in tty_set_ldisc(). Fixes unlikely possibility of failing to restart input kworker when switching to the same line discipline (noop case). Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Peter Hurley authored
SERIAL_DO_RESTART is not used by these 3 drivers; remove. Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Peter Hurley authored
tty_write_flush() has no definition and the TTY_WRITE_FLUSH() macro is never invoked; remove. Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Peter Hurley authored
A master pty should never be a controlling tty in Linux; if the master pty is specified to ioctl(TIOCSCTTY), silently substitute the slave pty as the controlling tty. Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Peter Hurley authored
Where possible, use dev_dbg() instead of pr_debug() Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Peter Hurley authored
WARN() does all of these things in one statement. Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Peter Hurley authored
Now that tty_debug() macro uses pr_debug(), the function name can be printed when using dynamic debug; printing the function name within the format string is redundant. Remove the __func__ parameter and print specifier from the format string. Add context to messages for when the function name is not printed by dynamic debug, or when dynamic debug is not enabled. Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Peter Hurley authored
Convert remaining printk() use to pr_*() when tty is unknown or unsafe to use. Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Peter Hurley authored
With the refactor of 'locked' from parameter to local, it's now obvious locked cannot be NULL. Remove entire conditional. Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Peter Hurley authored
Add tty as parameter to unset_locked_termios() and extract former parameters, termios and locked, as locals. Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Peter Hurley authored
Include the driver name in the tty_register_device_attr() error message for invalid index. Note that tty_err() cannot be used here because there is no tty; use pr_err(). Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Peter Hurley authored
Use tty_notice() for unified message format from the tty core. Fix each message to accurately reflect the cause of each termination. Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Peter Hurley authored
Since not all ttys are devices (eg., SysV ptys), dev_*() printk macros cannot be used. Define tty_*() printk macros that output in similar format to dev_*() macros (ie., <driver> <tty>: .....). Transform the most-trivial printk( LEVEL ...) usage to tty_*() usage. NB: The function name has been eliminated from messages with unique context, or prefixed to the format when given. Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Peter Hurley authored
Similar to tty_name(), add tty_driver_name() helper to safely dereference tty->driver->name (otherwise return empty string). Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Peter Hurley authored
kmalloc() already emits a diagnostic for failed allocations; remove tty-specific message. Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Peter Hurley authored
Eliminate symbol name collision with new tty core function, tty_driver_name(). Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Peter Hurley authored
tty_paranoia_check() is only used within drivers/tty/tty_io.c; remove extern declaration in header and limit symbol to file scope. Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Peter Hurley authored
Incorporate suggestions for tty core debug macro improvements - printk(KERN_DEBUG) => pr_debug() - ##args => ##__VA_ARGS__ - remove do {} while() - output tty_name() first cc: Joe Perches <joe@perches.com> Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Russell King authored
Prepare for REG_* register accessors. This change involves introducing pl011_reg_to_offset() to convert REG_* to the hardware register offset, and converting all call sites to use REG_* names. We need to fix up locations where we check for equivalence of register offsets as well. Much of this change was made via these sed expressions: s/ST_UART01[1x]\(_[^_]*\|_LCRH_[TR]X\)\>/REG_ST\1/ s/UART01[1x]_\(DR\|RSR\|ECR\|FR\|ILPR\|[IF]BRD\|LCRH\|CR\|IFLS\|IMSC\|RIS\|MIS\|ICR\|DMACR\)\>/REG_\1/g Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Reviewed-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Russell King authored
Add a helper to detect the split LCRH register found on ST variants. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Reviewed-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Russell King authored
Convert the new accessor functions to take the uart_amba_port instead of the port base address. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Reviewed-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Russell King authored
Add register accessor functions to amba-pl011. Much of this transformation was done using the sed expression below, with any left-overs fixed up manually afterwards, and code formatted to remain within coding style. s/readw(\(uap->port.membase\|regs\|port->membase\) +/pl011_read(\1,/g s/writew(\(.*\) +/pl011_write(\1,/g Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Reviewed-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Masahiro Yamada authored
Currently, 8-bit (MMIO) and 32-bit (MMIO32) register interfaces are supported for the 8250 console, but the 16-bit (MMIO16) is not. The 8250 UART device on my board is connected to a 16-bit bus and my main motivation is to use earlycon with it. (Refer to arch/arm/boot/dts/uniphier-support-card.dtsi) Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-