- 23 Jan, 2020 26 commits
-
-
Finn Thain authored
The netif_stop_queue() call in sonic_send_packet() races with the netif_wake_queue() call in sonic_interrupt(). This causes issues like "NETDEV WATCHDOG: eth0 (macsonic): transmit queue 0 timed out". Fix this by disabling interrupts when accessing tx_skb[] and next_tx. Update a comment to clarify the synchronization properties. Fixes: efcce839 ("[PATCH] macsonic/jazzsonic network drivers update") Tested-by:
Stan Johnson <userm57@yahoo.com> Signed-off-by:
Finn Thain <fthain@telegraphics.com.au> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Madalin Bucur authored
As the only 10G PHY interface type defined at the moment the code was developed was XGMII, although the PHY interface mode used was not XGMII, XGMII was used in the code to denote 10G. This patch renames the 10G interface mode to remove the ambiguity. Signed-off-by:
Madalin Bucur <madalin.bucur@oss.nxp.com> Signed-off-by:
-
David S. Miller authored
Madalin Bucur says: ==================== net: fsl/fman: address erratum A011043 This addresses a HW erratum on some QorIQ DPAA devices. MDIO reads to internal PCS registers may result in having the MDIO_CFG[MDIO_RD_ER] bit set, even when there is no error and read data (MDIO_DATA[MDIO_DATA]) is correct. Software may get false read error when reading internal PCS registers through MDIO. As a workaround, all internal MDIO accesses should ignore the MDIO_CFG[MDIO_RD_ER] bit. When the issue was present, one could see such errors during boot: mdio_bus ffe4e5000: Error while reading PHY0 reg at 3.3 ==================== Signed-off-by: -
Madalin Bucur authored
When fsl,erratum-a011043 is set, adjust for erratum A011043: MDIO reads to internal PCS registers may result in having the MDIO_CFG[MDIO_RD_ER] bit set, even when there is no error and read data (MDIO_DATA[MDIO_DATA]) is correct. Software may get false read error when reading internal PCS registers through MDIO. As a workaround, all internal MDIO accesses should ignore the MDIO_CFG[MDIO_RD_ER] bit. Signed-off-by:
-
Madalin Bucur authored
Add fsl,erratum-a011043 to internal MDIO buses. Software may get false read error when reading internal PCS registers through MDIO. As a workaround, all internal MDIO accesses should ignore the MDIO_CFG[MDIO_RD_ER] bit. Signed-off-by:
-
Madalin Bucur authored
Add an entry for erratum A011043: the MDIO_CFG[MDIO_RD_ER] bit may be falsely set when reading internal PCS registers. MDIO reads to internal PCS registers may result in having the MDIO_CFG[MDIO_RD_ER] bit set, even when there is no error and read data (MDIO_DATA[MDIO_DATA]) is correct. Software may get false read error when reading internal PCS registers through MDIO. As a workaround, all internal MDIO accesses should ignore the MDIO_CFG[MDIO_RD_ER] bit. Signed-off-by:
-
Manish Chopra authored
Driver while collecting firmware dump takes longer time to collect/process some of the firmware dump entries/memories. Bigger capture masks makes it worse as it results in larger amount of data being collected and results in CPU soft lockup. Place cond_resched() in some of the driver flows that are expectedly time consuming to relinquish the CPU to avoid CPU soft lockup panic. Signed-off-by:
Shahed Shaikh <shshaikh@marvell.com> Tested-by:
Yonggen Xu <Yonggen.Xu@dell.com> Signed-off-by:
Manish Chopra <manishc@marvell.com> Signed-off-by:
-
Kristian Evensen authored
When submitting v2 of "fou: Support binding FoU socket" (1713cb37), I accidentally sent the wrong version of the patch and one fix was missing. In the initial version of the patch, as well as the version 2 that I submitted, I incorrectly used ".type" for the two V6-attributes. The correct is to use ".len". Reported-by:
Dmitry Vyukov <dvyukov@google.com> Fixes: 1713cb37 ("fou: Support binding FoU socket") Signed-off-by:
Kristian Evensen <kristian.evensen@gmail.com> Signed-off-by:
-
David S. Miller authored
Merge tag 'wireless-drivers-2020-01-23' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers Kalle Valo says: ==================== wireless-drivers fixes for v5.5 Second set of fixes for v5.5. There are quite a few patches, especially on iwlwifi, due to me being on a long break. Libertas also has a security fix and mt76 a build fix. iwlwifi * don't send the PPAG command when PPAG is disabled, since it can cause problems * a few fixes for a HW bug * a fix for RS offload; * a fix for 3168 devices where the NVM tables where the wrong tables were being read * fix a couple of potential memory leaks in TXQ code * disable L0S states in all hardware since our hardware doesn't officially support them anymore (and older versions of the hardware had instability in these states) * remove lar_disable parameter since it has been causing issues for some people who erroneously disable it * force the debug monitor HW to stop also when debug is disabled, since it sometimes stays on and prevents low system power states * don't send IWL_MVM_RXQ_NSSN_SYNC notification due to DMA problems libertas * fix two buffer overflows mt76 * build fix related to CONFIG_MT76_LEDS * fix off by one in bitrates handling ==================== Signed-off-by:
-
Eric Dumazet authored
If both IFF_NAPI_FRAGS mode and XDP are enabled, and the XDP program consumes the skb, we need to clear the napi.skb (or risk a use-after-free) and release the mutex (or risk a deadlock) WARNING: lock held when returning to user space! 5.5.0-rc6-syzkaller #0 Not tainted ------------------------------------------------ syz-executor.0/455 is leaving the kernel with locks still held! 1 lock held by syz-executor.0/455: #0: ffff888098f6e748 (&tfile->napi_mutex){+.+.}, at: tun_get_user+0x1604/0x3fc0 drivers/net/tun.c:1835 Fixes: 90e33d45 ("tun: enable napi_gro_frags() for TUN/TAP driver") Signed-off-by:Eric Dumazet <edumazet@google.com> Reported-by:
syzbot <syzkaller@googlegroups.com> Cc: Petar Penkov <ppenkov@google.com> Cc: Willem de Bruijn <willemb@google.com> Signed-off-by:
-
Ido Schimmel authored
During reload (or module unload), the router block is de-initialized. Among other things, this results in the removal of a default multicast route from each active virtual router (VRF). These default routes are configured during initialization to trap packets to the CPU. In Spectrum-2, unlike Spectrum-1, multicast routes are implemented using ACL rules. Since the router block is de-initialized before the ACL block, it is possible that the ACL rules corresponding to the default routes are deleted while being accessed by the ACL delayed work that queries rules' activity from the device. This can result in a rare use-after-free [1]. Fix this by protecting the rules list accessed by the delayed work with a lock. We cannot use a spinlock as the activity read operation is blocking. [1] [ 123.331662] ================================================================== [ 123.339920] BUG: KASAN: use-after-free in mlxsw_sp_acl_rule_activity_update_work+0x330/0x3b0 [ 123.349381] Read of size 8 at addr ffff8881f3bb4520 by task kworker/0:2/78 [ 123.357080] [ 123.358773] CPU: 0 PID: 78 Comm: kworker/0:2 Not tainted 5.5.0-rc5-custom-33108-gf5df95d3ef41 #2209 [ 123.368898] Hardware name: Mellanox Technologies Ltd. MSN3700C/VMOD0008, BIOS 5.11 10/10/2018 [ 123.378456] Workqueue: mlxsw_core mlxsw_sp_acl_rule_activity_update_work [ 123.385970] Call Trace: [ 123.388734] dump_stack+0xc6/0x11e [ 123.392568] print_address_description.constprop.4+0x21/0x340 [ 123.403236] __kasan_report.cold.8+0x76/0xb1 [ 123.414884] kasan_report+0xe/0x20 [ 123.418716] mlxsw_sp_acl_rule_activity_update_work+0x330/0x3b0 [ 123.444034] process_one_work+0xb06/0x19a0 [ 123.453731] worker_thread+0x91/0xe90 [ 123.467348] kthread+0x348/0x410 [ 123.476847] ret_from_fork+0x24/0x30 [ 123.480863] [ 123.482545] Allocated by task 73: [ 123.486273] save_stack+0x19/0x80 [ 123.490000] __kasan_kmalloc.constprop.6+0xc1/0xd0 [ 123.495379] mlxsw_sp_acl_rule_create+0xa7/0x230 [ 123.500566] mlxsw_sp2_mr_tcam_route_create+0xf6/0x3e0 [ 123.506334] mlxsw_sp_mr_tcam_route_create+0x5b4/0x820 [ 123.512102] mlxsw_sp_mr_table_create+0x3b5/0x690 [ 123.517389] mlxsw_sp_vr_get+0x289/0x4d0 [ 123.521797] mlxsw_sp_fib_node_get+0xa2/0x990 [ 123.526692] mlxsw_sp_router_fib4_event_work+0x54c/0x2d60 [ 123.532752] process_one_work+0xb06/0x19a0 [ 123.537352] worker_thread+0x91/0xe90 [ 123.541471] kthread+0x348/0x410 [ 123.545103] ret_from_fork+0x24/0x30 [ 123.549113] [ 123.550795] Freed by task 518: [ 123.554231] save_stack+0x19/0x80 [ 123.557958] __kasan_slab_free+0x125/0x170 [ 123.562556] kfree+0xd7/0x3a0 [ 123.565895] mlxsw_sp_acl_rule_destroy+0x63/0xd0 [ 123.571081] mlxsw_sp2_mr_tcam_route_destroy+0xd5/0x130 [ 123.576946] mlxsw_sp_mr_tcam_route_destroy+0xba/0x260 [ 123.582714] mlxsw_sp_mr_table_destroy+0x1ab/0x290 [ 123.588091] mlxsw_sp_vr_put+0x1db/0x350 [ 123.592496] mlxsw_sp_fib_node_put+0x298/0x4c0 [ 123.597486] mlxsw_sp_vr_fib_flush+0x15b/0x360 [ 123.602476] mlxsw_sp_router_fib_flush+0xba/0x470 [ 123.607756] mlxsw_sp_vrs_fini+0xaa/0x120 [ 123.612260] mlxsw_sp_router_fini+0x137/0x384 [ 123.617152] mlxsw_sp_fini+0x30a/0x4a0 [ 123.621374] mlxsw_core_bus_device_unregister+0x159/0x600 [ 123.627435] mlxsw_devlink_core_bus_device_reload_down+0x7e/0xb0 [ 123.634176] devlink_reload+0xb4/0x380 [ 123.638391] devlink_nl_cmd_reload+0x610/0x700 [ 123.643382] genl_rcv_msg+0x6a8/0xdc0 [ 123.647497] netlink_rcv_skb+0x134/0x3a0 [ 123.651904] genl_rcv+0x29/0x40 [ 123.655436] netlink_unicast+0x4d4/0x700 [ 123.659843] netlink_sendmsg+0x7c0/0xc70 [ 123.664251] __sys_sendto+0x265/0x3c0 [ 123.668367] __x64_sys_sendto+0xe2/0x1b0 [ 123.672773] do_syscall_64+0xa0/0x530 [ 123.676892] entry_SYSCALL_64_after_hwframe+0x49/0xbe [ 123.682552] [ 123.684238] The buggy address belongs to the object at ffff8881f3bb4500 [ 123.684238] which belongs to the cache kmalloc-128 of size 128 [ 123.698261] The buggy address is located 32 bytes inside of [ 123.698261] 128-byte region [ffff8881f3bb4500, ffff8881f3bb4580) [ 123.711303] The buggy address belongs to the page: [ 123.716682] page:ffffea0007ceed00 refcount:1 mapcount:0 mapping:ffff888236403500 index:0x0 [ 123.725958] raw: 0200000000000200 dead000000000100 dead000000000122 ffff888236403500 [ 123.734646] raw: 0000000000000000 0000000000100010 00000001ffffffff 0000000000000000 [ 123.743315] page dumped because: kasan: bad access detected [ 123.749562] [ 123.751241] Memory state around the buggy address: [ 123.756620] ffff8881f3bb4400: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 123.764716] ffff8881f3bb4480: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc [ 123.772812] >ffff8881f3bb4500: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb [ 123.780904] ^ [ 123.785697] ffff8881f3bb4580: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc [ 123.793793] ffff8881f3bb4600: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 123.801883] ================================================================== Fixes: cf7221a4 ("mlxsw: spectrum_router: Add Multicast routing support for Spectrum-2") Signed-off-by:
Ido Schimmel <idosch@mellanox.com> Acked-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
-
David S. Miller authored
Hayes Wang says: ==================== r8152: serial fixes v3: 1. Fix the typos for patch #5 and #6. 2. Modify the commit message of patch #9. v2: For patch #2, move declaring the variable "ocp_data". v1: These patches are used to fix some issues for RTL8153. ==================== Signed-off-by: -
Hayes Wang authored
When enabling this, the device would wait an internal signal which wouldn't be triggered. Then, the device couldn't enter P3 mode, so the power consumption is increased. Signed-off-by:
Hayes Wang <hayeswang@realtek.com> Signed-off-by:
-
Hayes Wang authored
Avoid the MCU to clear the lanwake after suspending. It may cause the WOL fail. Disable LANWAKE_CLR_EN before suspending. Besides,enable it and reset the lanwake status when resuming or initializing. Signed-off-by:
-
Hayes Wang authored
For certain platforms, it causes USB reset periodically. Signed-off-by:
-
Hayes Wang authored
For RTL8153B with QFN32, disable test IO. Otherwise, it may cause abnormal behavior for the device randomly. Signed-off-by:
-
Hayes Wang authored
PLA MCU clock speed down could only be enabled when tx/rx are disabled. Otherwise, the packet loss may occur. Signed-off-by:
-
Hayes Wang authored
Enable U2P3 may miss zero packet for bulk-in. Signed-off-by:
-
Hayes Wang authored
Initailization would reset runtime suspend by tp->saved_wolopts, so the tp->saved_wolopts should be set before initializing. Signed-off-by:
-
Hayes Wang authored
When linking ON, the patch of flow control has to be reset. This makes sure the patch works normally. Signed-off-by:
-
Hayes Wang authored
Fix the runtime resume doesn't work normally for linking change. 1. Reset the settings and status of runtime suspend. 2. Sync the linking status. 3. Poll the linking change. Signed-off-by:
-
Eric Dumazet authored
A malicious user could use RAW sockets and fool GTP using them as standard SOCK_DGRAM UDP sockets. BUG: KMSAN: uninit-value in udp_tunnel_encap_enable include/net/udp_tunnel.h:174 [inline] BUG: KMSAN: uninit-value in setup_udp_tunnel_sock+0x45e/0x6f0 net/ipv4/udp_tunnel.c:85 CPU: 0 PID: 11262 Comm: syz-executor613 Not tainted 5.5.0-rc5-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x1c9/0x220 lib/dump_stack.c:118 kmsan_report+0xf7/0x1e0 mm/kmsan/kmsan_report.c:118 __msan_warning+0x58/0xa0 mm/kmsan/kmsan_instr.c:215 udp_tunnel_encap_enable include/net/udp_tunnel.h:174 [inline] setup_udp_tunnel_sock+0x45e/0x6f0 net/ipv4/udp_tunnel.c:85 gtp_encap_enable_socket+0x37f/0x5a0 drivers/net/gtp.c:827 gtp_encap_enable drivers/net/gtp.c:844 [inline] gtp_newlink+0xfb/0x1e50 drivers/net/gtp.c:666 __rtnl_newlink net/core/rtnetlink.c:3305 [inline] rtnl_newlink+0x2973/0x3920 net/core/rtnetlink.c:3363 rtnetlink_rcv_msg+0x1153/0x1570 net/core/rtnetlink.c:5424 netlink_rcv_skb+0x451/0x650 net/netlink/af_netlink.c:2477 rtnetlink_rcv+0x50/0x60 net/core/rtnetlink.c:5442 netlink_unicast_kernel net/netlink/af_netlink.c:1302 [inline] netlink_unicast+0xf9e/0x1100 net/netlink/af_netlink.c:1328 netlink_sendmsg+0x1248/0x14d0 net/netlink/af_netlink.c:1917 sock_sendmsg_nosec net/socket.c:639 [inline] sock_sendmsg net/socket.c:659 [inline] ____sys_sendmsg+0x12b6/0x1350 net/socket.c:2330 ___sys_sendmsg net/socket.c:2384 [inline] __sys_sendmsg+0x451/0x5f0 net/socket.c:2417 __do_sys_sendmsg net/socket.c:2426 [inline] __se_sys_sendmsg+0x97/0xb0 net/socket.c:2424 __x64_sys_sendmsg+0x4a/0x70 net/socket.c:2424 do_syscall_64+0xb8/0x160 arch/x86/entry/common.c:296 entry_SYSCALL_64_after_hwframe+0x44/0xa9 RIP: 0033:0x441359 Code: e8 ac e8 ff ff 48 83 c4 18 c3 0f 1f 80 00 00 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 eb 08 fc ff c3 66 2e 0f 1f 84 00 00 00 00 RSP: 002b:00007fff1cd0ac28 EFLAGS: 00000246 ORIG_RAX: 000000000000002e RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 0000000000441359 RDX: 0000000000000000 RSI: 0000000020000100 RDI: 0000000000000003 RBP: 00000000006cb018 R08: 00000000004002c8 R09: 00000000004002c8 R10: 00000000004002c8 R11: 0000000000000246 R12: 00000000004020d0 R13: 0000000000402160 R14: 0000000000000000 R15: 0000000000000000 Uninit was created at: kmsan_save_stack_with_flags+0x3c/0x90 mm/kmsan/kmsan.c:144 kmsan_internal_alloc_meta_for_pages mm/kmsan/kmsan_shadow.c:307 [inline] kmsan_alloc_page+0x12a/0x310 mm/kmsan/kmsan_shadow.c:336 __alloc_pages_nodemask+0x57f2/0x5f60 mm/page_alloc.c:4800 alloc_pages_current+0x67d/0x990 mm/mempolicy.c:2207 alloc_pages include/linux/gfp.h:534 [inline] alloc_slab_page+0x111/0x12f0 mm/slub.c:1511 allocate_slab mm/slub.c:1656 [inline] new_slab+0x2bc/0x1130 mm/slub.c:1722 new_slab_objects mm/slub.c:2473 [inline] ___slab_alloc+0x1533/0x1f30 mm/slub.c:2624 __slab_alloc mm/slub.c:2664 [inline] slab_alloc_node mm/slub.c:2738 [inline] slab_alloc mm/slub.c:2783 [inline] kmem_cache_alloc+0xb23/0xd70 mm/slub.c:2788 sk_prot_alloc+0xf2/0x620 net/core/sock.c:1597 sk_alloc+0xf0/0xbe0 net/core/sock.c:1657 inet_create+0x7c7/0x1370 net/ipv4/af_inet.c:321 __sock_create+0x8eb/0xf00 net/socket.c:1420 sock_create net/socket.c:1471 [inline] __sys_socket+0x1a1/0x600 net/socket.c:1513 __do_sys_socket net/socket.c:1522 [inline] __se_sys_socket+0x8d/0xb0 net/socket.c:1520 __x64_sys_socket+0x4a/0x70 net/socket.c:1520 do_syscall_64+0xb8/0x160 arch/x86/entry/common.c:296 entry_SYSCALL_64_after_hwframe+0x44/0xa9 Fixes: 459aa660 ("gtp: add initial driver for datapath of GPRS Tunneling Protocol (GTP-U)") Signed-off-by:
-
Eric Dumazet authored
rtnl_create_link() needs to apply dev->min_mtu and dev->max_mtu checks that we apply in do_setlink() Otherwise malicious users can crash the kernel, for example after an integer overflow : BUG: KASAN: use-after-free in memset include/linux/string.h:365 [inline] BUG: KASAN: use-after-free in __alloc_skb+0x37b/0x5e0 net/core/skbuff.c:238 Write of size 32 at addr ffff88819f20b9c0 by task swapper/0/0 CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.5.0-rc1-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: <IRQ> __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x197/0x210 lib/dump_stack.c:118 print_address_description.constprop.0.cold+0xd4/0x30b mm/kasan/report.c:374 __kasan_report.cold+0x1b/0x41 mm/kasan/report.c:506 kasan_report+0x12/0x20 mm/kasan/common.c:639 check_memory_region_inline mm/kasan/generic.c:185 [inline] check_memory_region+0x134/0x1a0 mm/kasan/generic.c:192 memset+0x24/0x40 mm/kasan/common.c:108 memset include/linux/string.h:365 [inline] __alloc_skb+0x37b/0x5e0 net/core/skbuff.c:238 alloc_skb include/linux/skbuff.h:1049 [inline] alloc_skb_with_frags+0x93/0x590 net/core/skbuff.c:5664 sock_alloc_send_pskb+0x7ad/0x920 net/core/sock.c:2242 sock_alloc_send_skb+0x32/0x40 net/core/sock.c:2259 mld_newpack+0x1d7/0x7f0 net/ipv6/mcast.c:1609 add_grhead.isra.0+0x299/0x370 net/ipv6/mcast.c:1713 add_grec+0x7db/0x10b0 net/ipv6/mcast.c:1844 mld_send_cr net/ipv6/mcast.c:1970 [inline] mld_ifc_timer_expire+0x3d3/0x950 net/ipv6/mcast.c:2477 call_timer_fn+0x1ac/0x780 kernel/time/timer.c:1404 expire_timers kernel/time/timer.c:1449 [inline] __run_timers kernel/time/timer.c:1773 [inline] __run_timers kernel/time/timer.c:1740 [inline] run_timer_softirq+0x6c3/0x1790 kernel/time/timer.c:1786 __do_softirq+0x262/0x98c kernel/softirq.c:292 invoke_softirq kernel/softirq.c:373 [inline] irq_exit+0x19b/0x1e0 kernel/softirq.c:413 exiting_irq arch/x86/include/asm/apic.h:536 [inline] smp_apic_timer_interrupt+0x1a3/0x610 arch/x86/kernel/apic/apic.c:1137 apic_timer_interrupt+0xf/0x20 arch/x86/entry/entry_64.S:829 </IRQ> RIP: 0010:native_safe_halt+0xe/0x10 arch/x86/include/asm/irqflags.h:61 Code: 98 6b ea f9 eb 8a cc cc cc cc cc cc e9 07 00 00 00 0f 00 2d 44 1c 60 00 f4 c3 66 90 e9 07 00 00 00 0f 00 2d 34 1c 60 00 fb f4 <c3> cc 55 48 89 e5 41 57 41 56 41 55 41 54 53 e8 4e 5d 9a f9 e8 79 RSP: 0018:ffffffff89807ce8 EFLAGS: 00000286 ORIG_RAX: ffffffffffffff13 RAX: 1ffffffff13266ae RBX: ffffffff8987a1c0 RCX: 0000000000000000 RDX: dffffc0000000000 RSI: 0000000000000006 RDI: ffffffff8987aa54 RBP: ffffffff89807d18 R08: ffffffff8987a1c0 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000000 R12: dffffc0000000000 R13: ffffffff8a799980 R14: 0000000000000000 R15: 0000000000000000 arch_cpu_idle+0xa/0x10 arch/x86/kernel/process.c:690 default_idle_call+0x84/0xb0 kernel/sched/idle.c:94 cpuidle_idle_call kernel/sched/idle.c:154 [inline] do_idle+0x3c8/0x6e0 kernel/sched/idle.c:269 cpu_startup_entry+0x1b/0x20 kernel/sched/idle.c:361 rest_init+0x23b/0x371 init/main.c:451 arch_call_rest_init+0xe/0x1b start_kernel+0x904/0x943 init/main.c:784 x86_64_start_reservations+0x29/0x2b arch/x86/kernel/head64.c:490 x86_64_start_kernel+0x77/0x7b arch/x86/kernel/head64.c:471 secondary_startup_64+0xa4/0xb0 arch/x86/kernel/head_64.S:242 The buggy address belongs to the page: page:ffffea00067c82c0 refcount:0 mapcount:0 mapping:0000000000000000 index:0x0 raw: 057ffe0000000000 ffffea00067c82c8 ffffea00067c82c8 0000000000000000 raw: 0000000000000000 0000000000000000 00000000ffffffff 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff88819f20b880: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ffff88819f20b900: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff >ffff88819f20b980: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ^ ffff88819f20ba00: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ffff88819f20ba80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff Fixes: 61e84623 ("net: centralize net_device min/max MTU checking") Signed-off-by: -
Michael Ellerman authored
The driver for Cisco Aironet 4500 and 4800 series cards (airo.c), implements AIROOLDIOCTL/SIOCDEVPRIVATE in airo_ioctl(). The ioctl handler copies an aironet_ioctl struct from userspace, which includes a command. Some of the commands are handled in readrids(), where the user controlled command is converted into a driver-internal value called "ridcode". There are two command values, AIROGWEPKTMP and AIROGWEPKNV, which correspond to ridcode values of RID_WEP_TEMP and RID_WEP_PERM respectively. These commands both have checks that the user has CAP_NET_ADMIN, with the comment that "Only super-user can read WEP keys", otherwise they return -EPERM. However there is another command value, AIRORRID, that lets the user specify the ridcode value directly, with no other checks. This means the user can bypass the CAP_NET_ADMIN check on AIROGWEPKTMP and AIROGWEPKNV. Fix it by moving the CAP_NET_ADMIN check out of the command handling and instead do it later based on the ridcode. That way regardless of whether the ridcode is set via AIROGWEPKTMP or AIROGWEPKNV, or passed in using AIRORID, we always do the CAP_NET_ADMIN check. Found by Ilja by code inspection, not tested as I don't have the required hardware. Reported-by:
Ilja Van Sprundel <ivansprundel@ioactive.com> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Michael Ellerman authored
The driver for Cisco Aironet 4500 and 4800 series cards (airo.c), implements AIROOLDIOCTL/SIOCDEVPRIVATE in airo_ioctl(). The ioctl handler copies an aironet_ioctl struct from userspace, which includes a command and a length. Some of the commands are handled in readrids(), which kmalloc()'s a buffer of RIDSIZE (2048) bytes. That buffer is then passed to PC4500_readrid(), which has two cases. The else case does some setup and then reads up to RIDSIZE bytes from the hardware into the kmalloc()'ed buffer. Here len == RIDSIZE, pBuf is the kmalloc()'ed buffer: // read the rid length field bap_read(ai, pBuf, 2, BAP1); // length for remaining part of rid len = min(len, (int)le16_to_cpu(*(__le16*)pBuf)) - 2; ... // read remainder of the rid rc = bap_read(ai, ((__le16*)pBuf)+1, len, BAP1); PC4500_readrid() then returns to readrids() which does: len = comp->len; if (copy_to_user(comp->data, iobuf, min(len, (int)RIDSIZE))) { Where comp->len is the user controlled length field. So if the "rid length field" returned by the hardware is < 2048, and the user requests 2048 bytes in comp->len, we will leak the previous contents of the kmalloc()'ed buffer to userspace. Fix it by kzalloc()'ing the buffer. Found by Ilja by code inspection, not tested as I don't have the required hardware. Reported-by: -
Andrew Lunn authored
phylink and phylib are interconnected. It makes sense for phylib and phy driver patches to be also reviewed by the phylink maintainer. So add Russell King as a designed reviewer of phylib. Signed-off-by:
Andrew Lunn <andrew@lunn.ch> Acked-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
- 22 Jan, 2020 8 commits
-
-
William Dauchy authored
in the same manner as commit d0f41851 ("net, ip_tunnel: fix namespaces move"), fix namespace moving as it was broken since commit 8d79266b ("ip6_tunnel: add collect_md mode to IPv6 tunnel"), but for ipv6 this time; there is no reason to keep it for ip6_tunnel. Fixes: 8d79266b ("ip6_tunnel: add collect_md mode to IPv6 tunnel") Signed-off-by:
William Dauchy <w.dauchy@criteo.com> Acked-by:
Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by:
-
Eric Dumazet authored
sysbot found another issue in tc_new_tfilter(). We probably should use @name which contains the sanitized version of TCA_KIND. BUG: KMSAN: uninit-value in string_nocheck lib/vsprintf.c:608 [inline] BUG: KMSAN: uninit-value in string+0x522/0x690 lib/vsprintf.c:689 CPU: 1 PID: 10753 Comm: syz-executor.1 Not tainted 5.5.0-rc5-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x1c9/0x220 lib/dump_stack.c:118 kmsan_report+0xf7/0x1e0 mm/kmsan/kmsan_report.c:118 __msan_warning+0x58/0xa0 mm/kmsan/kmsan_instr.c:215 string_nocheck lib/vsprintf.c:608 [inline] string+0x522/0x690 lib/vsprintf.c:689 vsnprintf+0x207d/0x31b0 lib/vsprintf.c:2574 __request_module+0x2ad/0x11c0 kernel/kmod.c:143 tcf_proto_lookup_ops+0x241/0x720 net/sched/cls_api.c:139 tcf_proto_create net/sched/cls_api.c:262 [inline] tc_new_tfilter+0x2a4e/0x5010 net/sched/cls_api.c:2058 rtnetlink_rcv_msg+0xcb7/0x1570 net/core/rtnetlink.c:5415 netlink_rcv_skb+0x451/0x650 net/netlink/af_netlink.c:2477 rtnetlink_rcv+0x50/0x60 net/core/rtnetlink.c:5442 netlink_unicast_kernel net/netlink/af_netlink.c:1302 [inline] netlink_unicast+0xf9e/0x1100 net/netlink/af_netlink.c:1328 netlink_sendmsg+0x1248/0x14d0 net/netlink/af_netlink.c:1917 sock_sendmsg_nosec net/socket.c:639 [inline] sock_sendmsg net/socket.c:659 [inline] ____sys_sendmsg+0x12b6/0x1350 net/socket.c:2330 ___sys_sendmsg net/socket.c:2384 [inline] __sys_sendmsg+0x451/0x5f0 net/socket.c:2417 __do_sys_sendmsg net/socket.c:2426 [inline] __se_sys_sendmsg+0x97/0xb0 net/socket.c:2424 __x64_sys_sendmsg+0x4a/0x70 net/socket.c:2424 do_syscall_64+0xb8/0x160 arch/x86/entry/common.c:296 entry_SYSCALL_64_after_hwframe+0x44/0xa9 RIP: 0033:0x45b349 Code: ad b6 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 7b b6 fb ff c3 66 2e 0f 1f 84 00 00 00 00 RSP: 002b:00007f88b3948c78 EFLAGS: 00000246 ORIG_RAX: 000000000000002e RAX: ffffffffffffffda RBX: 00007f88b39496d4 RCX: 000000000045b349 RDX: 0000000000000000 RSI: 00000000200001c0 RDI: 0000000000000003 RBP: 000000000075bfc8 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 00000000ffffffff R13: 000000000000099f R14: 00000000004cb163 R15: 000000000075bfd4 Uninit was created at: kmsan_save_stack_with_flags mm/kmsan/kmsan.c:144 [inline] kmsan_internal_poison_shadow+0x66/0xd0 mm/kmsan/kmsan.c:127 kmsan_slab_alloc+0x8a/0xe0 mm/kmsan/kmsan_hooks.c:82 slab_alloc_node mm/slub.c:2774 [inline] __kmalloc_node_track_caller+0xb40/0x1200 mm/slub.c:4382 __kmalloc_reserve net/core/skbuff.c:141 [inline] __alloc_skb+0x2fd/0xac0 net/core/skbuff.c:209 alloc_skb include/linux/skbuff.h:1049 [inline] netlink_alloc_large_skb net/netlink/af_netlink.c:1174 [inline] netlink_sendmsg+0x7d3/0x14d0 net/netlink/af_netlink.c:1892 sock_sendmsg_nosec net/socket.c:639 [inline] sock_sendmsg net/socket.c:659 [inline] ____sys_sendmsg+0x12b6/0x1350 net/socket.c:2330 ___sys_sendmsg net/socket.c:2384 [inline] __sys_sendmsg+0x451/0x5f0 net/socket.c:2417 __do_sys_sendmsg net/socket.c:2426 [inline] __se_sys_sendmsg+0x97/0xb0 net/socket.c:2424 __x64_sys_sendmsg+0x4a/0x70 net/socket.c:2424 do_syscall_64+0xb8/0x160 arch/x86/entry/common.c:296 entry_SYSCALL_64_after_hwframe+0x44/0xa9 Fixes: 6f96c3c6 ("net_sched: fix backward compatibility for TCA_KIND") Signed-off-by:
-
Paolo Abeni authored
This reverts commit 0d4a6608. Williem reported that after commit 0d4a6608 ("udp: do rmem bulk free even if the rx sk queue is empty") the memory allocated by an almost idle system with many UDP sockets can grow a lot. For stable kernel keep the solution as simple as possible and revert the offending commit. Reported-by:
Willem de Bruijn <willemdebruijn.kernel@gmail.com> Diagnosed-by:
Eric Dumazet <eric.dumazet@gmail.com> Fixes: 0d4a6608 ("udp: do rmem bulk free even if the rx sk queue is empty") Signed-off-by:
Paolo Abeni <pabeni@redhat.com> Acked-by:
Willem de Bruijn <willemb@google.com> Signed-off-by:
-
David S. Miller authored
Signed-off-by:
Jakub Kicinski <kuba@kernel.org>
-
Maxim Mikityanskiy authored
Commit 323ebb61 ("net: use listified RX for handling GRO_NORMAL skbs") introduces batching of GRO_NORMAL packets in napi_frags_finish, and commit 6570bc79 ("net: core: use listified Rx for GRO_NORMAL in napi_gro_receive()") adds the same to napi_skb_finish. However, dev_gro_receive (that is called just before napi_{frags,skb}_finish) can also pass skbs to the networking stack: e.g., when the GRO session is flushed, napi_gro_complete is called, which passes pp directly to netif_receive_skb_internal, skipping napi->rx_list. It means that the packet stored in pp will be handled by the stack earlier than the packets that arrived before, but are still waiting in napi->rx_list. It leads to TCP reorderings that can be observed in the TCPOFOQueue counter in netstat. This commit fixes the reordering issue by making napi_gro_complete also use napi->rx_list, so that all packets going through GRO will keep their order. In order to keep napi_gro_flush working properly, gro_normal_list calls are moved after the flush to clear napi->rx_list. iwlwifi calls napi_gro_flush directly and does the same thing that is done by gro_normal_list, so the same change is applied there: napi_gro_flush is moved to be before the flush of napi->rx_list. A few other drivers also use napi_gro_flush (brocade/bna/bnad.c, cortina/gemini.c, hisilicon/hns3/hns3_enet.c). The first two also use napi_complete_done afterwards, which performs the gro_normal_list flush, so they are fine. The latter calls napi_gro_receive right after napi_gro_flush, so it can end up with non-empty napi->rx_list anyway. Fixes: 323ebb61 ("net: use listified RX for handling GRO_NORMAL skbs") Signed-off-by:
Maxim Mikityanskiy <maximmi@mellanox.com> Cc: Alexander Lobakin <alobakin@dlink.ru> Cc: Edward Cree <ecree@solarflare.com> Acked-by:
Alexander Lobakin <alobakin@dlink.ru> Acked-by:
Saeed Mahameed <saeedm@mellanox.com> Acked-by:
Edward Cree <ecree@solarflare.com> Signed-off-by:
-
Richard Palethorpe authored
write_wakeup can happen in parallel with close/hangup where tty->disc_data is set to NULL and the netdevice is freed thus also freeing disc_data. write_wakeup accesses disc_data so we must prevent close from freeing the netdev while write_wakeup has a non-NULL view of tty->disc_data. We also need to make sure that accesses to disc_data are atomic. Which can all be done with RCU. This problem was found by Syzkaller on SLCAN, but the same issue is reproducible with the SLIP line discipline using an LTP test based on the Syzkaller reproducer. A fix which didn't use RCU was posted by Hillf Danton. Fixes: 661f7fda ("slip: Fix deadlock in write_wakeup") Fixes: a8e83b17 ("slcan: Port write_wakeup deadlock fix from slip") Reported-by: syzbot+017e491ae13c0068598a@syzkaller.appspotmail.com Signed-off-by:
Richard Palethorpe <rpalethorpe@suse.com> Cc: Wolfgang Grandegger <wg@grandegger.com> Cc: Marc Kleine-Budde <mkl@pengutronix.de> Cc: "David S. Miller" <davem@davemloft.net> Cc: Tyler Hall <tylerwhall@gmail.com> Cc: linux-can@vger.kernel.org Cc: netdev@vger.kernel.org Cc: linux-kernel@vger.kernel.org Cc: syzkaller@googlegroups.com Signed-off-by:
-
Jakub Sitnicki authored
As John Fastabend reports [0], psock state tear-down can happen on receive path *after* unlocking the socket, if the only other psock user, that is sockmap or sockhash, releases its psock reference before tcp_bpf_recvmsg does so: tcp_bpf_recvmsg() psock = sk_psock_get(sk) <- refcnt 2 lock_sock(sk); ... sock_map_free() <- refcnt 1 release_sock(sk) sk_psock_put() <- refcnt 0 Remove the lockdep check for socket lock in psock tear-down that got introduced in 7e81a353 ("bpf: Sockmap, ensure sock lock held during tear down"). [0] https://lore.kernel.org/netdev/5e25dc995d7d_74082aaee6e465b441@john-XPS-13-9370.notmuch/ Fixes: 7e81a353 ("bpf: Sockmap, ensure sock lock held during tear down") Reported-by: syzbot+d73682fcf7fee6982fe3@syzkaller.appspotmail.com Suggested-by:John Fastabend <john.fastabend@gmail.com> Signed-off-by:
Jakub Sitnicki <jakub@cloudflare.com> Acked-by:
Daniel Borkmann <daniel@iogearbox.net> Signed-off-by:
-
Emmanuel Grumbach authored
The purpose of this was to keep all the queues updated with the Rx sequence numbers because unlikely yet possible situations where queues can't understand if a specific packet needs to be dropped or not. Unfortunately, it was reported that this caused issues in our DMA engine. We don't fully understand how this is related, but this is being currently debugged. For now, just don't send this notification to the Rx queues. This de-facto reverts my commit 3c514bf8: iwlwifi: mvm: add a loose synchronization of the NSSN across Rx queues This issue was reported here: https://bugzilla.kernel.org/show_bug.cgi?id=204873 https://bugzilla.kernel.org/show_bug.cgi?id=205001 and others maybe. Fixes: 3c514bf8 ("iwlwifi: mvm: add a loose synchronization of the NSSN across Rx queues") CC: <stable@vger.kernel.org> # 5.3+ Signed-off-by:
Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org>
-
- 21 Jan, 2020 6 commits
-
-
William Dauchy authored
in the same manner as commit 690afc16 ("net: ip6_gre: fix moving ip6gre between namespaces"), fix namespace moving as it was broken since commit 2e15ea39 ("ip_gre: Add support to collect tunnel metadata."). Indeed, the ip6_gre commit removed the local flag for collect_md condition, so there is no reason to keep it for ip_gre/ip_tunnel. this patch will fix both ip_tunnel and ip_gre modules. Fixes: 2e15ea39 ("ip_gre: Add support to collect tunnel metadata.") Signed-off-by:
-
Theodore Dubois authored
Not sure how this got in here. git blame says the second assignment was added in 3a9a57f6, but that commit also removed the first assignment. Signed-off-by:
Theodore Dubois <tblodt@icloud.com> Signed-off-by:
-
James Hughes authored
As reported by Eric Dumazet, there are still some outstanding cases where the driver does not handle TSO correctly when skb's are over a certain size. Most cases have been fixed, this patch should ensure that forwarded SKB's that are greater than MAX_SINGLE_PACKET_SIZE - TX_OVERHEAD are software segmented and handled correctly. Signed-off-by:
James Hughes <james.hughes@raspberrypi.org> Reviewed-by:
-
Wen Yang authored
do_div() does a 64-by-32 division. Use div64_long() instead of it if the divisor is long, to avoid truncation to 32-bit. And as a nice side effect also cleans up the function a bit. Signed-off-by:
Wen Yang <wenyang@linux.alibaba.com> Cc: Eric Dumazet <edumazet@google.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru> Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org> Cc: netdev@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by:
-
Jouni Hogander authored
Netdev_register_kobject is calling device_initialize. In case of error reference taken by device_initialize is not given up. Drivers are supposed to call free_netdev in case of error. In non-error case the last reference is given up there and device release sequence is triggered. In error case this reference is kept and the release sequence is never started. Fix this by setting reg_state as NETREG_UNREGISTERED if registering fails. This is the rootcause for couple of memory leaks reported by Syzkaller: BUG: memory leak unreferenced object 0xffff8880675ca008 (size 256): comm "netdev_register", pid 281, jiffies 4294696663 (age 6.808s) hex dump (first 32 bytes): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ backtrace: [<0000000058ca4711>] kmem_cache_alloc_trace+0x167/0x280 [<000000002340019b>] device_add+0x882/0x1750 [<000000001d588c3a>] netdev_register_kobject+0x128/0x380 [<0000000011ef5535>] register_netdevice+0xa1b/0xf00 [<000000007fcf1c99>] __tun_chr_ioctl+0x20d5/0x3dd0 [<000000006a5b7b2b>] tun_chr_ioctl+0x2f/0x40 [<00000000f30f834a>] do_vfs_ioctl+0x1c7/0x1510 [<00000000fba062ea>] ksys_ioctl+0x99/0xb0 [<00000000b1c1b8d2>] __x64_sys_ioctl+0x78/0xb0 [<00000000984cabb9>] do_syscall_64+0x16f/0x580 [<000000000bde033d>] entry_SYSCALL_64_after_hwframe+0x44/0xa9 [<00000000e6ca2d9f>] 0xffffffffffffffff BUG: memory leak unreferenced object 0xffff8880668ba588 (size 8): comm "kobject_set_nam", pid 286, jiffies 4294725297 (age 9.871s) hex dump (first 8 bytes): 6e 72 30 00 cc be df 2b nr0....+ backtrace: [<00000000a322332a>] __kmalloc_track_caller+0x16e/0x290 [<00000000236fd26b>] kstrdup+0x3e/0x70 [<00000000dd4a2815>] kstrdup_const+0x3e/0x50 [<0000000049a377fc>] kvasprintf_const+0x10e/0x160 [<00000000627fc711>] kobject_set_name_vargs+0x5b/0x140 [<0000000019eeab06>] dev_set_name+0xc0/0xf0 [<0000000069cb12bc>] netdev_register_kobject+0xc8/0x320 [<00000000f2e83732>] register_netdevice+0xa1b/0xf00 [<000000009e1f57cc>] __tun_chr_ioctl+0x20d5/0x3dd0 [<000000009c560784>] tun_chr_ioctl+0x2f/0x40 [<000000000d759e02>] do_vfs_ioctl+0x1c7/0x1510 [<00000000351d7c31>] ksys_ioctl+0x99/0xb0 [<000000008390040a>] __x64_sys_ioctl+0x78/0xb0 [<0000000052d196b7>] do_syscall_64+0x16f/0x580 [<0000000019af9236>] entry_SYSCALL_64_after_hwframe+0x44/0xa9 [<00000000bc384531>] 0xffffffffffffffff v3 -> v4: Set reg_state to NETREG_UNREGISTERED if registering fails v2 -> v3: * Replaced BUG_ON with WARN_ON in free_netdev and netdev_release v1 -> v2: * Relying on driver calling free_netdev rather than calling put_device directly in error path Reported-by: syzbot+ad8ca40ecd77896d51e2@syzkaller.appspotmail.com Cc: David Miller <davem@davemloft.net> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Lukas Bulwahn <lukas.bulwahn@gmail.com> Signed-off-by:Jouni Hogander <jouni.hogander@unikie.com> Signed-off-by:
-
Yuki Taguchi authored
After LRO/GRO is applied, SRv6 encapsulated packets have SKB_GSO_IPXIP6 feature flag, and this flag must be removed right after decapulation procedure. Currently, SKB_GSO_IPXIP6 flag is not removed on End.D* actions, which creates inconsistent packet state, that is, a normal TCP/IP packets have the SKB_GSO_IPXIP6 flag. This behavior can cause unexpected fallback to GSO on routing to netdevices that do not support SKB_GSO_IPXIP6. For example, on inter-VRF forwarding, decapsulated packets separated into small packets by GSO because VRF devices do not support TSO for packets with SKB_GSO_IPXIP6 flag, and this degrades forwarding performance. This patch removes encapsulation related GSO flags from the skb right after the End.D* action is applied. Fixes: d7a669dd ("ipv6: sr: add helper functions for seg6local") Signed-off-by:
Yuki Taguchi <tagyounit@gmail.com> Signed-off-by:
-
