The original table handling code does not always verify checksums before
installing a table, this is because code to achieve this must be
implemented here and there in the redundant code blocks.

There are two stages during table initialization:
1. "INSTALLED" after acpi_tb_install_table() and acpi_tb_override_table(),
   struct acpi_table_desc.Pointer is ensured to be NULL.  This can be safely used
   during OSPM's early boot stage.
2. "VALIDATED" after acpi_tb_validate_table(), struct acpi_table_desc.Pointer is
   ensured to be not NULL.  This must not be used during OSPM's early boot
   stage.

This patch changes acpi_tb_add_table() into an early boot safe API to reduce
code redundancies by changing the table state that is returned by this
function from "VALIDATED" to "INSTALLED".  Then the table verification
code can be done in a single place.  Originally, the acpi_tb_add_table() can
only be used by dynamic table loadings that are executed after early boot
stage, it cannot be used by static table loadings that are executed in
early boot stage as:
1.  The address of the table is a virtual address either maintained by
    OSPMs who call acpi_load_table() or by ACPICA whenever "Load" or
    "LoadTable" opcodes are executed, while during early boot stage,
    physical address of the table should be used for table loading.
2.  The API will ensure the state of the loaded table to be "VALIDATED"
    while during early boot stage, tables maintained by root table list
    should be kept as "INSTALLED".

To achieve this:
1. Rename acpi_tb_install_table() to acpi_tb_install_fixed_table() as it only
   applies to DSDT/FACS installation.  Rename acpi_tb_add_table() to
   acpi_tb_install_non_fixed_table() as it will be applied to the installation
   of the rest kinds of tables.
2. Introduce acpi_tb_install_table(), acpi_tb_install_and_override_table to collect
   redudant code where their invocations actually have slight differences.
   1. acpi_tb_install_table() is used to fill an struct acpi_table_desc where the
      table length is known to the caller.
   2. acpi_tb_install_and_override_table() is used to perform necessary
      overriding before installation.
3. Change a parameter of acpi_tb_install_non_fixed_table() from struct acpi_table_desc
   to acpi_physical_address to allow it to be invoked by static table
   loadings.  Also cleanup acpi_ex_load_op() and acpi_load_table() to accomodate
   to the parameter change.
4. Invoke acpi_tb_install_non_fixed_table() for all table loadings other than
   DSDT/FACS in acpi_tb_parse_root_table() to improve code maintainability
   (logics are collected in the single function).  Also delete useless code
   from acpi_tb_parse_root_table().
5. Remove all acpi_tb_validate_table() from acpi_tb_install_non_fixed_table() and
   acpi_tb_install_fixed_table() so that the table descriptor is kept in the
   state of "INSTALLED" but not "VALIDATED" after returning from these
   functions.
6. Introduce temporary struct acpi_table_desc (new_table_desc/old_table_desc) into
   the functions to indicate a table descriptor that is not maintained by
   acpi_gbl_root_table_list. Introduce acpi_tb_acquire_temporal_table() and
   acpi_tb_release_temporal_table() to handle the use cases of such temporal
   tables.  They are only used for verified installation.
7. Introduce acpi_tb_verify_table() to validate table and verify table
   checksum, also remove table checksum verification from
   acpi_tb_validate_table(). Invoke acpi_tb_validate_table() in the functions
   that will convert a table into "LOADED" state or invoke it from
   acpi_get_table_XXX() APIs. Invoke acpi_tb_verify_table() on temporary
   struct acpi_table_desc(s) that are going to be "INSTALLED".
8. Change acpi_tb_override_table() logic so that a temporary struct acpi_table_desc
   will be overridden before installtion, this makes code simpler.

After applying the patch, tables are always installed after being
overridden and the table checksums are always verified before installation.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
[rjw: Subject]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

As acpi_tb_validate_table() returns failure on checksum verification without
doing invalidatation, all its invocations that are not done to a descriptor
stored in acpi_gbl_root_table_list are checked and balanced.

But this is not a real issue as the descritors that have been passed to
acpi_tb_add_table() are all virtual address tables and the validations are in
fact no-op.  The cleanup can ensure that any future extensions made on
acpi_tb_add_table() to allow it to be invoked with physical address tables
will not trigger memory leakage regressions.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
[rjw: Subject]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

This patch is mainly a naming cleanup to clarify hidden logics, no
functional changes.

acpi_initialize_tables() is used by Linux to install table addresses for
early boot steps.  During this stage, table addresses are mapped by
early_ioremap() mechanism which is different from the runtime IO mappings.
Thus it is not safe for ACPICA to keep mapped pointers in struct acpi_table_desc
structure during this stage.

In order to support this in ACPICA, table states are divided into
1. "INSTALLED" (where struct acpi_table_desc.Pointer is always NULL) and
2. "VALIDATED" (where struct acpi_table_desc.Pointer is always not NULL).
During acpi_initialize_tables(), table state are ensured to be "INSTALLED"
but not "VALIDATED".  This logic is ensured by the original code in very
ambigious way.  For example, currently acpi_tb_delete_table() is invoked in
some place to perform an uninstallation while it is invoked in other place
to perform an invalidation.  They happen to work just because no one enters
the penalty where the 2 behaviours are not equivalent.

The naming cleanups are made in this patch:
A. For installation and validation:
   There is code setting struct acpi_table_desc.Pointer first and delete it
   immediately to keep the descriptor's state as "INSTALLED" during the
   installation.  This patch implements this in more direct way.  After
   applying it, struct acpi_table_desc.Pointer will never be set in
   acpi_tb_install_table() and acpi_tb_override_table() as they are the only
   functions invoked during acpi_initialize_tables(). This is achieved by:
1. Rename acpi_tb_verify_table() to acpi_tb_validate_table() to clarify this
   change.
2. Rename acpi_tb_table_override() to acpi_tb_override_table() to keep nameing
   consistencies as other APIs (verb. Table).
3. Stops setting struct acpi_table_desc.Pointer in acpi_tb_install_table() and
   acpi_tb_table_override().
4. Introduce acpi_tb_acquire_table() to acquire the table pointer that is not
   maintained in the struct acpi_table_desc of the global root table list and
   rewrite acpi_tb_validate_table() using this new function to reduce
   redundancies.
5. Replace the table pointer using the overridden table pointer in
   acpi_tb_add_table(). As acpi_tb_add_table() is not invoked during early boot
   stage, tables returned from this functions should be "VALIDATED".  As
   acpi_tb_override_table() is modified by this patch to return a "INSTALLED"
   but not "VALIDATED" descriptor, to keep acpi_tb_add_table() unchanged,
   struct acpi_table_desc.Pointer is filled in acpi_tb_add_table().
B. For invalidation and uninstallation:
   The original code invalidate table by invoking acpi_tb_delete_table() here
   and there, but actually this function should only be used to uninstall
   tables.  This can work just because its invocations are equivalent to
   invalidation in some cases.
   This patch splits acpi_tb_delete_table() into acpi_tb_invalidate_table() and
   acpi_tb_uninstall_table() and cleans up the hidden logic using the new
   APIs.  This is achieved by:
1. Rename acpi_tb_delete_table() to acpi_tb_uninstall_table() as it is mainly
   called before resetting struct acpi_table_desc.Address.  Thus the table
   descriptor is in "not INSTALLED" state.  This patch enforces this by
   setting struct acpi_table_desc.Address to NULL in this function.
2. Introduce acpi_tb_invalidate_table() to be the reversal of
   acpi_tb_validate_table() and invoke it in acpi_tb_uninstall_table().
3. Introduce acpi_tb_release_table() to release the table pointer that is not
   maintained in acpi_gbl_root_table_list and rewrite acpi_tb_invalidate_table()
   using this new function to reduce redundancies.

After cleaning up, the maintainability of the internal APIs are also
improved:
1. acpi_tb_acquire_table: Acquire struct acpi_table_header according to
                       ACPI_TABLE_ORIGIN_xxx flags.
2. acpi_tb_release_table: Release struct acpi_table_header according to
                       ACPI_TABLE_ORIGIN_xxx flags.
3. acpi_tb_install_table: Make struct acpi_table_desc.Address not NULL according to
                       ACPI_TABLE_ORIGIN_xxx flags.
4. acpi_tb_uninstall_table: Make struct acpi_table_desc.Address NULL according to
                         ACPI_TABLE_ORIGIN_xxx flags.
5. acpi_tb_validate_table: Make struct acpi_table_desc.Pointer not NULL according to
                        ACPI_TABLE_ORIGIN_xxx flags.
6. acpi_tb_invalidate_table: Make struct acpi_table_desc.Pointer NULL according to
                          ACPI_TABLE_ORIGIN_xxx flags.
7. acpi_tb_override_table: Replace struct acpi_table_desc.Address and
                        struct acpi_table_desc.Flags.  It only happens in
                        "INSTALLED" state.

The patch has been unit tested in acpi_exec by:
1. Initializing;
2. Executing exc_tbl ASLTS tests;
3. Executing "Load" command.
So that all original acpi_tb_install_table() and acpi_tb_override_table()
invocations are covered.

Known Issues:
1. Cleanup acpi_tb_add_table() to Kill Code Redundancies
   Current implementation in acpi_tb_add_table() is not very clean, further
   patch can rewrite acpi_tb_add_table() with ordered acpi_tb_install_table(),
   acpi_tb_override_table() and acpi_tb_validate_table(). It is not done in this
   patch so that it is easy for the reviewers to understand the changes in
   this patch.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Currently there are following issues in acpi_tb_add_table():
Following logic is currently correct:
1. When a table is allocated in acpi_ex_load_op(), if a reloading happens,
   the allocated memory is freed by acpi_tb_add_table() and AE_OK is
   returned to the caller to avoid the caller to free it again.
Following logic is currently incorrect:
1. When a table is allocated in acpi_ex_load_op() or by the
   acpi_load_table() caller, if the table is already loaded, there will be
   twice ACPI_FREE() called for the same pointer when acpi_tb_add_table()
   returns AE_ALREADY_EXISTS.

This patch only fixes the above incorrect logic in acpi_tb_add_table():
1. Only invoke acpi_tb_delete_table() if AE_OK is going to be returned.
2. After doing so, we do not invoke ACPI_FREE() when returning AE_OK;
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
[rjw: Subject]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

When table is overridden or reloaded, acpi_tb_delete_table() is called where
struct acpi_table_desc.Pointer will be NULL.  It thus is impossible for virtual
addressed tables to obtain the .Pointer again in acpi_tb_verify_table().

This patch stores virtual table addresses  (ACPI_TABLE_ORIGIN_ALLOCATED,
ACPI_TABLE_ORIGIN_UNKNOWN, ACPI_TABLE_ORIGIN_OVERRIDE) in the
struct acpi_table_desc.Address field and refills the struct acpi_table_desc.Pointer
using these addresses in acpi_tb_verify_table(). Note that if a table with
ACPI_TABLE_ORIGIN_ALLOCATED set is actually freed, the .Address field
should be invalidated and thus must be replaced with NULL to avoid wrong
future validations occuring in acpi_tb_verify_table().
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

The divergences in the ACPICA files makes it difficult to maintain linuxize
ACPICA table commits.  This patch reduces such divergences before applying
table manager commits so that human interventions of patch rebasing can be
reduced.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
[rjw: Subject]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Adds "OriginalSyncLevel" field to the output.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Adds PPC64 as a 64-bit architecture. Colin Ian King.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

When the following commmit is back ported to ACPICA, comments have been
updated:
  Subject: ACPICA: Linux-specific header: Update support for Linux/acpi
           applications.

This patch back ports the differences between the ACPICA upstream and
Linux.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
[rjw: Subject]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

This patch cleans up all of the acpi_os_wait_events_complete() invocations to
make it to be invoked inside of ACPICA in the way to accommodate Linux's
work queue implementation.

According to the report, current Linux kernel code is facing a boot time
race issue in the acpi_remove_notify_handler(). This is because:
Linux is using work queues to implement a deferred handler call environment
while ACPICA expects OSPM to implement acpi_os_wait_events_complete() using
wait queues.  The position to invoke a "waiter" is not suitable for a
"flusher" as new invocations can be scheduled after this position and
before the deletion of the handler from its management container.

Since the following commit has deleted acpi_os_wait_events_complete()
parameters, it thus might not be possible for OSPM to achieve a safe
removal using wait queues.  This requires ACPICA to be changed accordingly
to "flush" handlers rather than "wait" them to be drain up:

  Commit: 5ff986a2a9db11858247b71fe242fe17617229aa
  Date: Wed, 16 May 2012 13:36:07 -0700
  Subject: Introduce acpi_os_wait_events_complete interface.

  This interface will block until asynchronous events like notifies
  and GPEs are complete. Within ACPICA, it is called before a notify or GPE
  handler is removed. ACPICA BZ 868.

This patch fixes this issue by invoking acpi_os_wait_events_complete() in the
way to "flush" things - it thus should be put to the position after handler
is removed from its management container but before it is destructed.

The technical concerns are:
1. MTX_NAMESPACE is used to protect things that acpi_os_wait_events_complete()
   might be waiting for, thus MTX_NAMESPACE must be unlocked before
   invoking acpi_os_wait_events_complete().
2. MTX_NAMESPACE is also used to implement the serialization of
   acpi_install_notify_handler() and acpi_remove_notify_handler(). This patch
   changes this logic, thus if there are many
   acpi_install/remove_notify_handler() invoked in parallel, the
   acpi_os_wait_events_complete() might face the races which could cause it
   never running to an end.  Normally this will require additional code to
   implement a separate locking facility which is not implemented due to 3.
3. Given ACPICA users will always invoke acpi_install_notify_handler() once
   during Linux module/device initialization and invoke
   acpi_remove_notify_handler() once during module/device finalization,
   problem stated in 2 will not happen in Linux environment due to the
   mutual exclusive module/device existence, this fix thus is sufficient.
Same concerns can apply to acpi_install/remove_gpe_handler(). Reported and
tested: Ronald Vink.  Fixed: Lv Zheng.

References: https://bugzilla.kernel.org/show_bug.cgi?id=60583Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Reported-and-Tested-by: Ronald Vink <ronald.vink@boskalis.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

For Notify operators, displays a comment that describe the meaning
of the notify value.

This patch updates the debugging information that is enabled for
CONFIG_ACPI_DEBUG builds.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

For _HID and _CID, the disassembler will emit a string that describes
the device if the _HID/_CID value is recognized. acpihelp updated also.
acpihelp will now search for a specific ID as well as displaying
the list of "known" (to ACPICA) IDs.

This patch does not affect Linux kernel behavior as the disassembler
and the acpihelp are not shipped with it.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

We would like to see the ASL for any machine that uses this operator,
so emit at least a warning to hopefully draw some attention.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Some versions of gcc implement strchr via a macro, which either
contains bugs or can provoke a bug in the compiler. This change
fixes a possible compile-time error when using this function.
The problem is usually seen when compiling the getopt.c module.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Change all comments that contain the string "ACPI CA" to "ACPICA"
so that the name is standard across the entire source base.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

ACPICA BZ 1077. David Binderman.

References: https://bugs.acpica.org/show_bug.cgi?id=1077Signed-off-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Cc: 3.9+ <stable@vger.kernel.org> # 3.9.x: 42f8fb75: ACPICA: Source restructuring
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

These recently added interfaces did not have these macros, used
by some hosts.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Some versions of gcc even warn about it:

  mm/shmem.c: In function ‘shmem_file_aio_read’:
  mm/shmem.c:1414: warning: ‘error’ may be used uninitialized in this function

If the loop is aborted during the first iteration by one of the two
first break statements, error will be uninitialized.

Introduced by commit 6e58e79d ("introduce copy_page_to_iter, kill
loop over iovec in generic_file_aio_read()").
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

On 32 bit, size_t is "unsigned int", not "unsigned long", causing the
following warning when comparing with PAGE_SIZE, which is always "unsigned
long":

  fs/cifs/file.c: In function ‘cifs_readdata_to_iov’:
  fs/cifs/file.c:2757: warning: comparison of distinct pointer types lacks a cast

Introduced by commit 7f25bba8 ("cifs_iovec_read: keep iov_iter
between the calls of cifs_readdata_to_iov()"), which changed the
signedness of "remaining" and the code from min_t() to min().
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull slab changes from Pekka Enberg:
 "The biggest change is byte-sized freelist indices which reduces slab
  freelist memory usage:

    https://lkml.org/lkml/2013/12/2/64"

* 'slab/next' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/linux:
  mm: slab/slub: use page->list consistently instead of page->lru
  mm/slab.c: cleanup outdated comments and unify variables naming
  slab: fix wrongly used macro
  slub: fix high order page allocation problem with __GFP_NOFAIL
  slab: Make allocations with GFP_ZERO slightly more efficient
  slab: make more slab management structure off the slab
  slab: introduce byte sized index for the freelist of a slab
  slab: restrict the number of objects in a slab
  slab: introduce helper functions to get/set free object
  slab: factor out calculate nr objects in cache_estimate

Pull misc kbuild changes from Michal Marek:
 "Here is the non-critical part of kbuild:
   - One bogus coccinelle check removed, one check fixed not to suggest
     the obsolete PTR_RET macro
   - scripts/tags.sh does not index the generated *.mod.c files
   - new objdiff tool to list differences between two versions of an
     object file
   - A fix for scripts/bootgraph.pl"

* 'misc' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
  scripts/coccinelle: Use PTR_ERR_OR_ZERO
  scripts/bootgraph.pl: Add graphic header
  scripts: objdiff: detect object code changes between two commits
  Coccicheck: Remove memcpy to struct assignment test
  scripts/tags.sh: Ignore *.mod.c

This patch fixes I/O errors with the sym53c8xx_2 driver when the disk
returns QUEUE FULL status.

When the controller encounters an error (including QUEUE FULL or BUSY
status), it aborts all not yet submitted requests in the function
sym_dequeue_from_squeue.

This function aborts them with DID_SOFT_ERROR.

If the disk has full tag queue, the request that caused the overflow is
aborted with QUEUE FULL status (and the scsi midlayer properly retries
it until it is accepted by the disk), but the sym53c8xx_2 driver aborts
the following requests with DID_SOFT_ERROR --- for them, the midlayer
does just a few retries and then signals the error up to sd.

The result is that disk returning QUEUE FULL causes request failures.

The error was reproduced on 53c895 with COMPAQ BD03685A24 disk
(rebranded ST336607LC) with command queue 48 or 64 tags.  The disk has
64 tags, but under some access patterns it return QUEUE FULL when there
are less than 64 pending tags.  The SCSI specification allows returning
QUEUE FULL anytime and it is up to the host to retry.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit 8f619b54 ("powerpc/ppc64: Do not turn AIL (reloc-on
interrupts) too early") added code to set the AIL bit in the LPCR
without checking whether the kernel is running in hypervisor mode.  The
result is that when the kernel is running as a guest (i.e., under
PowerKVM or PowerVM), the processor takes a privileged instruction
interrupt at that point, causing a panic.  The visible result is that
the kernel hangs after printing "returning from prom_init".

This fixes it by checking for hypervisor mode being available before
setting LPCR.  If we are not in hypervisor mode, we enable relocation-on
interrupts later in pSeries_setup_arch using the H_SET_MODE hcall.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commits 11d4616b ("futex: revert back to the explicit waiter
counting code") and 69cd9eba ("futex: avoid race between requeue and
wake") changed some of the finer details of how we think about futexes.
One was a late fix and the other a consequence of overlooking the whole
requeuing logic.

The first change caused our documentation to be incorrect, and the
second made us aware that we need to explicitly add more details to it.
Signed-off-by: Davidlohr Bueso <davidlohr@hp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull yet more networking updates from David Miller:

 1) Various fixes to the new Redpine Signals wireless driver, from
    Fariya Fatima.

 2) L2TP PPP connect code takes PMTU from the wrong socket, fix from
    Dmitry Petukhov.

 3) UFO and TSO packets differ in whether they include the protocol
    header in gso_size, account for that in skb_gso_transport_seglen().
   From Florian Westphal.

 4) If VLAN untagging fails, we double free the SKB in the bridging
    output path.  From Toshiaki Makita.

 5) Several call sites of sk->sk_data_ready() were referencing an SKB
    just added to the socket receive queue in order to calculate the
    second argument via skb->len.  This is dangerous because the moment
    the skb is added to the receive queue it can be consumed in another
    context and freed up.

    It turns out also that none of the sk->sk_data_ready()
    implementations even care about this second argument.

    So just kill it off and thus fix all these use-after-free bugs as a
    side effect.

 6) Fix inverted test in tcp_v6_send_response(), from Lorenzo Colitti.

 7) pktgen needs to do locking properly for LLTX devices, from Daniel
    Borkmann.

 8) xen-netfront driver initializes TX array entries in RX loop :-) From
    Vincenzo Maffione.

 9) After refactoring, some tunnel drivers allow a tunnel to be
    configured on top itself.  Fix from Nicolas Dichtel.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (46 commits)
  vti: don't allow to add the same tunnel twice
  gre: don't allow to add the same tunnel twice
  drivers: net: xen-netfront: fix array initialization bug
  pktgen: be friendly to LLTX devices
  r8152: check RTL8152_UNPLUG
  net: sun4i-emac: add promiscuous support
  net/apne: replace IS_ERR and PTR_ERR with PTR_ERR_OR_ZERO
  net: ipv6: Fix oif in TCP SYN+ACK route lookup.
  drivers: net: cpsw: enable interrupts after napi enable and clearing previous interrupts
  drivers: net: cpsw: discard all packets received when interface is down
  net: Fix use after free by removing length arg from sk_data_ready callbacks.
  Drivers: net: hyperv: Address UDP checksum issues
  Drivers: net: hyperv: Negotiate suitable ndis version for offload support
  Drivers: net: hyperv: Allocate memory for all possible per-pecket information
  bridge: Fix double free and memory leak around br_allowed_ingress
  bonding: Remove debug_fs files when module init fails
  i40evf: program RSS LUT correctly
  i40evf: remove open-coded skb_cow_head
  ixgb: remove open-coded skb_cow_head
  igbvf: remove open-coded skb_cow_head
  ...

Merge tag 'blackfin-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/realmz6/blackfin-linux

Pull blackfin updates from Steven Miao:
 "Code cleanup, some previously ignored patches, and bug fixes"

* tag 'blackfin-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/realmz6/blackfin-linux:
  blackfin: cleanup board files
  bf609: clock: drop unused clock bit set/clear functions
  Blackfin: bf537: rename "CONFIG_ADT75"
  Blackfin: bf537: rename "CONFIG_AD7314"
  Blackfin: bf537: rename ad2s120x ->ad2s1200
  blackfin: bf537: fix typo "CONFIG_SND_SOC_ADV80X_MODULE"
  blackfin: dma: current count mmr is read only
  bfin_crc: Move architecture independant crc header file out of the blackfin folder.
  bf54x: drop unuesd HOST status,control,timeout registers bit define macros
  blackfin: portmux: cleanup head file
  Blackfin: remove "config IP_CHECKSUM_L1"
  blackfin: Remove GENERIC_GPIO config option again
  blackfin:Use generic /proc/interrupts implementation
  blackfin: bf60x: fix typo "CONFIG_PM_BFIN_WAKE_PA15_POL"

Merge tag 'remoteproc-3.15-cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/ohad/remoteproc

Pull remoteproc cleanups from Ohad Ben-Cohen:
 "Several remoteproc cleanup patches coming from Jingoo Han, Julia
  Lawall and Uwe Kleine-König"

* tag 'remoteproc-3.15-cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/ohad/remoteproc:
  remoteproc/ste_modem: staticize local symbols
  remoteproc/davinci: simplify use of devm_ioremap_resource
  remoteproc/davinci: drop needless devm_clk_put

Pull llvm patches from Behan Webster:
 "These are some initial updates to support compiling the kernel with
  clang.

  These patches have been through the proper reviews to the best of my
  ability, and have been soaking in linux-next for a few weeks.  These
  patches by themselves still do not completely allow clang to be used
  with the kernel code, but lay the foundation for other patches which
  are still under review.

  Several other of the LLVMLinux patches have been already added via
  maintainer trees"

* tag 'llvmlinux-for-v3.15' of git://git.linuxfoundation.org/llvmlinux/kernel:
  x86: LLVMLinux: Fix "incomplete type const struct x86cpu_device_id"
  x86 kbuild: LLVMLinux: More cc-options added for clang
  x86, acpi: LLVMLinux: Remove nested functions from Thinkpad ACPI
  LLVMLinux: Add support for clang to compiler.h and new compiler-clang.h
  LLVMLinux: Remove warning about returning an uninitialized variable
  kbuild: LLVMLinux: Fix LINUX_COMPILER definition script for compilation with clang
  Documentation: LLVMLinux: Update Documentation/dontdiff
  kbuild: LLVMLinux: Adapt warnings for compilation with clang
  kbuild: LLVMLinux: Add Kbuild support for building kernel with Clang

Pull SCSI target updates from Nicholas Bellinger:
 "Here are the target pending updates for v3.15-rc1.  Apologies in
  advance for waiting until the second to last day of the merge window
  to send these out.

  The highlights this round include:

   - iser-target support for T10 PI (DIF) offloads (Sagi + Or)
   - Fix Task Aborted Status (TAS) handling in target-core (Alex Leung)
   - Pass in transport supported PI at session initialization (Sagi + MKP + nab)
   - Add WRITE_INSERT + READ_STRIP T10 PI support in target-core (nab + Sagi)
   - Fix iscsi-target ERL=2 ASYNC_EVENT connection pointer bug (nab)
   - Fix tcm_fc use-after-free of ft_tpg (Andy Grover)
   - Use correct ib_sg_dma primitives in ib_isert (Mike Marciniszyn)

  Also, note the virtio-scsi + vhost-scsi changes to expose T10 PI
  metadata into KVM guest have been left-out for now, as there where a
  few comments from MST + Paolo that where not able to be addressed in
  time for v3.15.  Please expect this feature for v3.16-rc1"

* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (43 commits)
  ib_srpt: Use correct ib_sg_dma primitives
  target/tcm_fc: Rename ft_tport_create to ft_tport_get
  target/tcm_fc: Rename ft_{add,del}_lport to {add,del}_wwn
  target/tcm_fc: Rename structs and list members for clarity
  target/tcm_fc: Limit to 1 TPG per wwn
  target/tcm_fc: Don't export ft_lport_list
  target/tcm_fc: Fix use-after-free of ft_tpg
  target: Add check to prevent Abort Task from aborting itself
  target: Enable READ_STRIP emulation in target_complete_ok_work
  target/sbc: Add sbc_dif_read_strip software emulation
  target: Enable WRITE_INSERT emulation in target_execute_cmd
  target/sbc: Add sbc_dif_generate software emulation
  target/sbc: Only expose PI read_cap16 bits when supported by fabric
  target/spc: Only expose PI mode page bits when supported by fabric
  target/spc: Only expose PI inquiry bits when supported by fabric
  target: Pass in transport supported PI at session initialization
  target/iblock: Fix double bioset_integrity_free bug
  Target/sbc: Initialize COMPARE_AND_WRITE write_sg scatterlist
  target/rd: T10-Dif: RAM disk is allocating more space than required.
  iscsi-target: Fix ERL=2 ASYNC_EVENT connection pointer bug
  ...

Pull media fixes from Mauro Carvalho Chehab:
 "A series of bug fix patches for v3.15-rc1.  Most are just driver
  fixes.  There are some changes at remote controller core level, fixing
  some definitions on a new API added for Kernel v3.15.

  It also adds the missing include at include/uapi/linux/v4l2-common.h,
  to allow its compilation on userspace, as pointed by you"

* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (24 commits)
  [media] gpsca: remove the risk of a division by zero
  [media] stk1160: warrant a NUL terminated string
  [media] v4l: ti-vpe: retain v4l2_buffer flags for captured buffers
  [media] v4l: ti-vpe: Set correct field parameter for output and capture buffers
  [media] v4l: ti-vpe: zero out reserved fields in try_fmt
  [media] v4l: ti-vpe: Fix initial configuration queue data
  [media] v4l: ti-vpe: Use correct bus_info name for the device in querycap
  [media] v4l: ti-vpe: report correct capabilities in querycap
  [media] v4l: ti-vpe: Allow usage of smaller images
  [media] v4l: ti-vpe: Use video_device_release_empty
  [media] v4l: ti-vpe: Make sure in job_ready that we have the needed number of dst_bufs
  [media] lgdt3305: include sleep functionality in lgdt3304_ops
  [media] drx-j: use customise option correctly
  [media] m88rs2000: fix sparse static warnings
  [media] r820t: fix size and init values
  [media] rc-core: remove generic scancode filter
  [media] rc-core: split dev->s_filter
  [media] rc-core: do not change 32bit NEC scancode format for now
  [media] rtl28xxu: remove duplicate ID 0458:707f Genius TVGo DVB-T03
  [media] xc2028: add missing break to switch
  ...

Pull PCIe non-transparent bridge fixes and features from Jon Mason:
 "NTB driver bug fixes to address issues in list traversal, skb leak in
  ntb_netdev, a typo, and a leak of msix entries in the error path.
  Clean ups of the event handling logic, as well as a overall style
  cleanup.  Finally, the driver was converted to use the new
  pci_enable_msix_range logic (and the refactoring to go along with it)"

* tag 'ntb-3.15' of git://github.com/jonmason/ntb:
  ntb: Use pci_enable_msix_range() instead of pci_enable_msix()
  ntb: Split ntb_setup_msix() into separate BWD/SNB routines
  ntb: Use pci_msix_vec_count() to obtain number of MSI-Xs
  NTB: Code Style Clean-up
  NTB: client event cleanup
  ntb: Fix leakage of ntb_device::msix_entries[] array
  NTB: Fix typo in setting one translation register
  ntb_netdev: Fix skb free issue in open
  ntb_netdev: Fix list_for_each_entry exit issue

The vfs merge caused a latent bug to show up:

   In file included from fs/ceph/super.h:4:0,
                    from fs/ceph/ioctl.c:3:
   include/linux/ceph/ceph_debug.h:4:0: warning: "pr_fmt" redefined [enabled by default]
    #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
    ^
   In file included from include/linux/kernel.h:13:0,
                    from include/linux/uio.h:12,
                    from include/linux/socket.h:7,
                    from include/uapi/linux/in.h:22,
                    from include/linux/in.h:23,
                    from fs/ceph/ioctl.c:1:
   include/linux/printk.h:214:0: note: this is the location of the previous definition
    #define pr_fmt(fmt) fmt
    ^

where the reason is that <linux/ceph_debug.h> is included much too late
for the "pr_fmt()" define.

The include of <linux/ceph_debug.h> needs to be the first include in the
file, but fs/ceph/ioctl.c had for some reason missed that, and it wasn't
noticeable until some unrelated header file changes brought in an
indirect earlier include of <linux/kernel.h>.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull vfs updates from Al Viro:
 "The first vfs pile, with deep apologies for being very late in this
  window.

  Assorted cleanups and fixes, plus a large preparatory part of iov_iter
  work.  There's a lot more of that, but it'll probably go into the next
  merge window - it *does* shape up nicely, removes a lot of
  boilerplate, gets rid of locking inconsistencie between aio_write and
  splice_write and I hope to get Kent's direct-io rewrite merged into
  the same queue, but some of the stuff after this point is having
  (mostly trivial) conflicts with the things already merged into
  mainline and with some I want more testing.

  This one passes LTP and xfstests without regressions, in addition to
  usual beating.  BTW, readahead02 in ltp syscalls testsuite has started
  giving failures since "mm/readahead.c: fix readahead failure for
  memoryless NUMA nodes and limit readahead pages" - might be a false
  positive, might be a real regression..."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (63 commits)
  missing bits of "splice: fix racy pipe->buffers uses"
  cifs: fix the race in cifs_writev()
  ceph_sync_{,direct_}write: fix an oops on ceph_osdc_new_request() failure
  kill generic_file_buffered_write()
  ocfs2_file_aio_write(): switch to generic_perform_write()
  ceph_aio_write(): switch to generic_perform_write()
  xfs_file_buffered_aio_write(): switch to generic_perform_write()
  export generic_perform_write(), start getting rid of generic_file_buffer_write()
  generic_file_direct_write(): get rid of ppos argument
  btrfs_file_aio_write(): get rid of ppos
  kill the 5th argument of generic_file_buffered_write()
  kill the 4th argument of __generic_file_aio_write()
  lustre: don't open-code kernel_recvmsg()
  ocfs2: don't open-code kernel_recvmsg()
  drbd: don't open-code kernel_recvmsg()
  constify blk_rq_map_user_iov() and friends
  lustre: switch to kernel_sendmsg()
  ocfs2: don't open-code kernel_sendmsg()
  take iov_iter stuff to mm/iov_iter.c
  process_vm_access: tidy up a bit
  ...

Nicolas Dichtel says:

====================
tunnels: don't allow to add the same tunnel twice

This series fixes the check of an existing tunnel with the same
parameters when a new tunnel is added.  I've checked all users of
ip_tunnel_newlink(): gre, gretap, ipip and vti. The bug exists only
for gre and vti.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Before the patch, it was possible to add two times the same tunnel:
ip l a vti1 type vti remote 10.16.0.121 local 10.16.0.249 key 41
ip l a vti2 type vti remote 10.16.0.121 local 10.16.0.249 key 41

It was possible, because ip_tunnel_newlink() calls ip_tunnel_find() with the
argument dev->type, which was set only later (when calling ndo_init handler
in register_netdevice()). Let's set this type in the setup handler, which is
called before newlink handler.

Introduced by commit b9959fd3 ("vti: switch to new ip tunnel code").

CC: Cong Wang <amwang@redhat.com>
CC: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Before the patch, it was possible to add two times the same tunnel:
ip l a gre1 type gre remote 10.16.0.121 local 10.16.0.249
ip l a gre2 type gre remote 10.16.0.121 local 10.16.0.249

It was possible, because ip_tunnel_newlink() calls ip_tunnel_find() with the
argument dev->type, which was set only later (when calling ndo_init handler
in register_netdevice()). Let's set this type in the setup handler, which is
called before newlink handler.

Introduced by commit c5441932 ("GRE: Refactor GRE tunneling code.").

CC: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes the initialization of an array used in the TX
datapath that was mistakenly initialized together with the
RX datapath arrays. An out of range array access could happen
when RX and TX rings had different sizes.
Signed-off-by: Vincenzo Maffione <v.maffione@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates

This series contains updates to e1000, e1000e, igb, igbvf, ixgb, ixgbe,
ixgbevf and i40evf.

Mark fixes an issue with ixgbe and ixgbevf by adding a bit to indicate
when workqueues have been initialized.  This permits the register read
error handling from attempting to use them prior to that, which also
generates warnings.  Checking for a detected removal after initializing
the work queues allows the probe function to return an error without
getting the workqueue involved.  Further, if the error_detected
callback is entered before the workqueues are initialized, exit without
recovery since the device initialization was so truncated.

Francois Romieu provides several patches to all the drivers to remove
the open coded skb_cow_head.

Jakub Kicinski provides a fix for igb where last_rx_timestamp should be
updated only when Rx time stamp is read.

Mitch provides a fix for i40evf where a recent change broke the RSS LUT
programming causing it to be programmed with all 0's.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull more tracing updates from Steven Rostedt:
 "This includes the final patch to clean up and fix the issue with the
  design of tracepoints and how a user could register a tracepoint and
  have that tracepoint not be activated but no error was shown.

  The design was for an out of tree module but broke in tree users.  The
  clean up was to remove the saving of the hash table of tracepoint
  names such that they can be enabled before they exist (enabling a
  module tracepoint before that module is loaded).  This added more
  complexity than needed.  The clean up was to remove that code and just
  enable tracepoints that exist or fail if they do not.

  This removed a lot of code as well as the complexity that it brought.
  As a side effect, instead of registering a tracepoint by its name, the
  tracepoint needs to be registered with the tracepoint descriptor.
  This removes having to duplicate the tracepoint names that are
  enabled.

  The second patch was added that simplified the way modules were
  searched for.

  This cleanup required changes that were in the 3.15 queue as well as
  some changes that were added late in the 3.14-rc cycle.  This final
  change waited till the two were merged in upstream and then the change
  was added and full tests were run.  Unfortunately, the test found some
  errors, but after it was already submitted to the for-next branch and
  not to be rebased.  Sparse errors were detected by Fengguang Wu's bot
  tests, and my internal tests discovered that the anonymous union
  initialization triggered a bug in older gcc compilers.  Luckily, there
  was a bugzilla for the gcc bug which gave a work around to the
  problem.  The third and fourth patch handled the sparse error and the
  gcc bug respectively.

  A final patch was tagged along to fix a missing documentation for the
  README file"

* tag 'trace-3.15-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  tracing: Add missing function triggers dump and cpudump to README
  tracing: Fix anonymous unions in struct ftrace_event_call
  tracepoint: Fix sparse warnings in tracepoint.c
  tracepoint: Simplify tracepoint module search
  tracepoint: Use struct pointer instead of name hash for reg/unreg tracepoints