Skip to content

L
linux
Switch branch/tag
  1. 01 Dec, 2014 26 commits
  3. 27 Nov, 2014 1 commit
  5. 26 Nov, 2014 13 commits
    • Dmitry Tunin's avatar
      Bluetooth: ath3k: Add support of MCI 13d3:3408 bt device · 3bb30a7c
      Dmitry Tunin authored 
      Add support for Bluetooth MCI WB335 (AR9565) Wi-Fi+bt module. This
Bluetooth module requires loading patch and sysconfig by ath3k driver.

T:  Bus=01 Lev=02 Prnt=03 Port=00 Cnt=01 Dev#= 20 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=13d3 ProdID=3408 Rev= 0.02
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
A:  FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
Signed-off-by: default avatarDmitry Tunin <hanipouspilot@gmail.com>
Signed-off-by: default avatarJohan Hedberg <johan.hedberg@intel.com>
Cc: stable@vger.kernel.org
      3bb30a7c
    • Michal Kazior's avatar
      ath10k: fix station count enforcement · cfd1061e
      Michal Kazior authored 
      The number of peers isn't directly translatable to
the number of stations because ath10k needs to
reserve a few extra peers for special cases like
multi-vif concurrency.

The previous limit was 126 and 15 stations in AP
mode for 10.x and main firmware branches
respectively. The limit is now 128 and 16 which
was the original intention.
Signed-off-by: default avatarMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: default avatarKalle Valo <kvalo@qca.qualcomm.com>
      cfd1061e
    • Michal Kazior's avatar
      ath10k: clean up num_peers locking · 292a753d
      Michal Kazior authored 
      The var was supposed to be protected by data_lock
but it wasn't so in all instances. It's actually
not necessary to have a spinlock protected
num_peers so drop it.

All instances of num_peers are already within
conf_mutex sections so use that.
Signed-off-by: default avatarMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: default avatarKalle Valo <kvalo@qca.qualcomm.com>
      292a753d
    • Michal Kazior's avatar
      ath10k: add missing goto · a52c0282
      Michal Kazior authored 
      This prevents warning spamming if peer creation
fails during sta_state in some cases.
Signed-off-by: default avatarMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: default avatarKalle Valo <kvalo@qca.qualcomm.com>
      a52c0282
    • Yanbo Li's avatar
      ath10k: add memory dump debugfs interface · 9f65ad25
      Yanbo Li authored 
      Add mem_val debugfs file for dumping the firmware (target) memory and also for
writing to the memory. The firmware memory is accessed through one file which
uses position of the file as the firmware memory address. For example, with dd
use skip parameter for the address.

Beucase target memory width is 32 bits it's strongly recommended to use
blocksize divisable with 4 when using this interface. For example, when using
dd use bs=4 to set the block size to 4 and remember to divide both count and
skip values with four.

To read 4 kB chunk from address 0x400000:

dd if=mem_value bs=4 count=1024 skip=1048576 | xxd -g1

To write value 0x01020304 to address 0x400400:

echo 0x01020304 | xxd -r | dd of=mem_value bs=4 seek=1048832

To read 4 KB chunk of memory and then write back after edit:

dd if=mem_value of=tmp.bin bs=4 count=1024 skip=1048576
emacs tmp.bin
dd if=tmp.bin of=mem_value bs=4 count=1024 seek=1048576
Signed-off-by: default avatarYanbo Li <yanbol@qti.qualcomm.com>
Signed-off-by: default avatarKalle Valo <kvalo@qca.qualcomm.com>
      9f65ad25
    • Yanbo Li's avatar
      ath10k: add register access debugfs interface · 077a3804
      Yanbo Li authored 
      Debugfs files reg_addr and reg_val are used for reading and writing to the
firmware (target) registers. reg_addr contains the address to be accessed,
which also needs to be set first, and reg_value is when used for reading and
writing the actual value in ASCII.

To read a value from the firmware register 0x100000:

# echo 0x100000 > reg_addr
# cat reg_value
0x00100000:0x000002d3

To write value 0x2400 to address 0x100000:

# echo 0x100000 > reg_addr
# echo  0x2400 > reg_value
#
Signed-off-by: default avatarYanbo Li <yanbol@qti.qualcomm.com>
Signed-off-by: default avatarKalle Valo <kvalo@qca.qualcomm.com>
      077a3804
    • Sujith Manoharan's avatar
      ath10k: fix bug reported by lockdep · 5d011f5c
      Sujith Manoharan authored 
      ath10k_tx_wep_key_work() acquires conf_mutex, so
cancelling it when conf_mutex is already taken
in ath10k_remove_interface() is incorrect, so
move it outside the lock.

Snippet from the lockdep report:

kernel: ======================================================
kernel: [ INFO: possible circular locking dependency detected ]
kernel: 3.18.0-rc5-wl-debug #34 Tainted: G           O
kernel: -------------------------------------------------------
kernel: hostapd/451 is trying to acquire lock:
kernel:  ((&arvif->wep_key_work)){+.+...}, at: [<ffffffff810872d5>] flush_work+0x5/0x290
kernel: but task is already holding lock:
kernel:  (&ar->conf_mutex){+.+.+.}, at: [<ffffffffa0b99f00>] ath10k_remove_interface+0x40/0x290 [ath10k_core]
kernel: which lock already depends on the new lock.
Signed-off-by: default avatarSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: default avatarKalle Valo <kvalo@qca.qualcomm.com>
      5d011f5c
    • Sujith Manoharan's avatar
      ath10k: fix locking for WEP keys · ae167131
      Sujith Manoharan authored 
      peer->keys needs to be protected by data_lock
since it is also accessed from the WMI path.

Both install() and clear() routines for peer
keys modify the key contents, so use the data_lock
to avoid races.
Signed-off-by: default avatarSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: default avatarKalle Valo <kvalo@qca.qualcomm.com>
      ae167131
    • Sujith Manoharan's avatar
      ath10k: fix shared WEP · 504f6cdf
      Sujith Manoharan authored 
      When static keys are used in shared WEP, when a
station is associated, message 3 is sent with an
encrypted payload. But, for subsequent
authentications that are triggered without a
deauth, the auth frame is decrypted by the HW.

To handle this, check if the WEP keys have already
been set for the peer and if so, mark the
frame as decrypted. This scenario can happen
when a station changes its default TX key and initiates
a new authentication sequence.
Signed-off-by: default avatarSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: default avatarKalle Valo <kvalo@qca.qualcomm.com>
      504f6cdf
    • Michal Kazior's avatar
      ath10k: don't drop corrupted mgmt frames · d67d0a02
      Michal Kazior authored 
      Some firmware revisions don't seem to deilver
management frames with FCS error via WMI so narrow
down the HTT rule to not drop corrupted management
frames.

This basically increases number of frames ath10k
reports while sniffing.
Signed-off-by: default avatarMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: default avatarKalle Valo <kvalo@qca.qualcomm.com>
      d67d0a02
    • Michal Kazior's avatar
      ath10k: fix offchannel cancel failures · 7305d3e0
      Michal Kazior authored 
      When mac80211 requests driver to cancel a hw roc
the driver must not call the expired() callback or
else roc will fail in some cases depending on how
things get scheduled.
Signed-off-by: default avatarMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: default avatarKalle Valo <kvalo@qca.qualcomm.com>
      7305d3e0
    • Michal Kazior's avatar
      ath10k: make hw roc more reliable · dcca0bdb
      Michal Kazior authored 
      With P2P concurrency requested hw roc duration
time can be very small. Some firmware revisions
refuse scan requests with too small channel dwell
time.

This prevents messages like, e.g. with connected
STA vif and performing P2P Find:

 ath10k_pci 0000:00:05.0: failed to switch to channel for roc scan
 ieee80211 phy3: failed to start next HW ROC (-110)
Signed-off-by: default avatarMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: default avatarKalle Valo <kvalo@qca.qualcomm.com>
      dcca0bdb
    • Michal Kazior's avatar
      ath10k: fix offchan reliability · 8d6d3624
      Michal Kazior authored 
      New firmware revisions don't need peer creation
when doing offchannel tx. Earlier revisions would
queue and never release frames without a peer.

This prevent new firmware revisions from stopping
replenishing wmi-htc tx credits and improves
reliability of offchannel tx which would sometimes
silently fail.
Signed-off-by: default avatarMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: default avatarKalle Valo <kvalo@qca.qualcomm.com>
      8d6d3624
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7