- 05 May, 2021 2 commits
-
-
Roy Sun authored
Tracking devices, process info and fence info using /proc/pid/fdinfo Signed-off-by:
David M Nieto <David.Nieto@amd.com> Signed-off-by:
Roy Sun <Roy.Sun@amd.com> Reviewed-by:
Christian König <christian.koenig@amd.com> Signed-off-by:
-
Roy Sun authored
Update the timestamp of scheduled fence on HW completion of the previous fences This allow more accurate tracking of the fence execution in HW v2 (chk): drop the flag check and improve the comment Signed-off-by:
-
- 04 May, 2021 3 commits
-
-
Alex Deucher authored
TTM uses drm-misc now. Update the tree. Cc: David Ward <david.ward@gatech.edu> Reviewed-by:
Alex Deucher <alexander.deucher@amd.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210503134736.1467003-1-alexander.deucher@amd.com
-
Douglas Anderson authored
The ti_sn_gpio_unregister() is not just called from the remove path but also from the error handling of the init path. That means it can't have the __exit annotation. Fixes: bf73537f ("drm/bridge: ti-sn65dsi86: Break GPIO and MIPI-to-eDP bridge into sub-drivers") Reported-by:
kernel test robot <lkp@intel.com> Signed-off-by:
Douglas Anderson <dianders@chromium.org> Reviewed-by:
Robert Foss <robert.foss@linaro.org> Signed-off-by:
-
Christian König authored
Include the header for the prototype. Signed-off-by:
Matthew Auld <matthew.auld@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210503142710.153369-1-christian.koenig@amd.com
-
- 03 May, 2021 27 commits
-
-
Douglas Anderson authored
It doesn't make sense to go out to the bus and read the EDID over and over again. Let's cache it and throw away the cache when we turn power off from the panel. Autosuspend means that even if there are several calls to read the EDID before we officially turn the power on then we should get good use out of this cache. Signed-off-by:
Bjorn Andersson <bjorn.andersson@linaro.org> Reviewed-by:
Sean Paul <seanpaul@chromium.org> Acked-by:
Linus Walleij <linus.walleij@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20210423095743.v5.18.If050957eaa85cf45b10bcf61e6f7fa61c9750ebf@changeid
-
Douglas Anderson authored
I don't believe that it ever makes sense to read the EDID when a panel is not powered and the powering on of the panel is the job of prepare(). Let's make sure that this happens before we try to read the EDID. We use the pm_runtime functions directly rather than directly calling the normal prepare() function because the pm_runtime functions are definitely refcounted whereas it's less clear if the prepare() one is. NOTE: I'm not 100% sure how EDID reading was working for folks in the past, but I can only assume that it was failing on the initial attempt and then working only later. This patch, presumably, will fix that. If some panel out there really can read the EDID without powering up and it's a big advantage to preserve the old behavior we can add a per-panel flag. It appears that providing the DDC bus to the panel in the past was somewhat uncommon in any case. Signed-off-by:
-
Douglas Anderson authored
As of commit 5186421c ("drm: Introduce epoch counter to drm_connector") the drm_get_edid() function calls drm_connector_update_edid_property() for us. There's no reason for us to call it again. Signed-off-by:
-
Douglas Anderson authored
Let's reorganize how we init and turn on the reference clock in the code to allow us to turn it on early (even before pre_enable()) so that we can read the EDID early. This is handy for eDP because: - We always assume that a panel is there. - Once we report that a panel is there we get asked to read the EDID. - Pre-enable isn't called until we know what pixel clock we want to use and we're ready to turn everything on. That's _after_ we get asked to read the EDID. NOTE: the above only works out OK if we "refclk" is provided. Though I don't have access to any hardware that uses ti-sn65dsi86 and _doesn't_ provide a "refclk", I believe that we'll have trouble reading the EDID at bootup in that case. Specifically I believe that if there's no "refclk" we need the MIPI source clock to be active before we can successfully read the EDID. My evidence here is that, in testing, I couldn't read the EDID until I turned on the DPPLL in the bridge chip and that the DPPLL needs the input clock to be active. Since this is hard to support, let's punt trying to handle this case if there's no "refclk". In that case we'll enable comms in pre_enable() like we always did. I don't believe there are any users of the ti-sn65dsi86 bridge chip that _don't_ use "refclk". The bridge chip is _very_ inflexible in that mode. The only time I've seen that mode used was for some really early prototype hardware that was thrown in the e-waste bin years ago when we realized how inflexible it was. Even if someone is using the bridge chip without the "refclk" they're in no worse shape than they were before the (fairly recent) commit 58074b08 ("drm/bridge: ti-sn65dsi86: Read EDID blob over DDC"). Signed-off-by:
-
Douglas Anderson authored
No functional changes--this just makes the diffstat of a future change easier to understand. Signed-off-by:
-
Douglas Anderson authored
Let's make the bridge use autosuspend with a 500ms delay. This is in preparation for promoting DP AUX transfers to their own sub-driver so that we're not constantly powering up and down the device as we transfer all the chunks. Signed-off-by:
-
Douglas Anderson authored
When I added support for the hpd-gpio to simple-panel in commit 48834e60 ("drm/panel-simple: Support hpd-gpios for delaying prepare()"), I added a special case to handle a circular dependency I was running into on the ti-sn65dsi86 bridge chip. On my board the hpd-gpio is actually provided by the bridge chip. That was causing some circular dependency problems that I had to work around by getting the hpd-gpio late. I've now reorganized the ti-sn65dsi86 bridge chip driver to be a collection of sub-drivers. Now the GPIO part can probe separately and that breaks the chain. Let's get rid of the old code to clean things up. Signed-off-by:
-
Douglas Anderson authored
Let's use the newly minted aux bus to break up the driver into sub drivers. We're not doing a full breakup here: all the code is still in the same file and remains largely untouched. The big goal here of using sub-drivers is to allow part of our code to finish probing even if some other code needs to defer. This can solve some chicken-and-egg problems. Specifically: - In commit 48834e60 ("drm/panel-simple: Support hpd-gpios for delaying prepare()") we had to add a bit of a hack to simpel-panel to support HPD showing up late. We can get rid of that hack now since the GPIO part of our driver can finish probing early. - We have a desire to expose our DDC bus to simple-panel (and perhaps to a backlight driver?). That will end up with the same chicken-and-egg problem. A future patch to move this to a sub-driver will fix it. - If/when we support the PWM functionality present in the bridge chip for a backlight we'll end up with another chicken-and-egg problem. If we allow the PWM to be a sub-driver too then it solves this problem. Signed-off-by:
-
Douglas Anderson authored
This is just code motion of the probe routine to move all the things that are for the "whole chip" (instead of the GPIO parts or the MIPI-to-eDP parts) together at the start of probe. This is in preparation for breaking the driver into sub-drivers. Since we're using devm for all of the "whole chip" stuff this is actually quite easy now. Signed-off-by:
-
Douglas Anderson authored
Let's: - Set the drvdata as soon as it's allocated. This just sets up a pointer so there's no downside here. - Remove the useless call to i2c_set_clientdata() which is literally the same thing as dev_set_drvdata(). No functional changes intended. Signed-off-by:
-
Douglas Anderson authored
Tiny cleanup for probe so we don't keep having to specify "&client->dev" or "pdata->dev". No functional changes intended. Signed-off-by:
-
Douglas Anderson authored
Let's cleanup the debugfs code to: - Check for errors. - Use devm to manage freeing, which also means we don't need to store a pointer in our structure. Signed-off-by:
-
Douglas Anderson authored
There's no devm_runtime_enable(), but it's easy to use devm_add_action_or_reset() and means we don't need to worry about the disable in our remove() routine or in error paths. No functional changes intended by this change. Signed-off-by:
-
Douglas Anderson authored
Like the previous patch ("drm/bridge: ti-sn65dsi86: Rename the main driver data structure") this is just a no-op rename in preparation for splitting the driver up a bit. Here I've attempted to rename functions / structures making sure that anything applicable to the whole chip (instead of just the MIPI to eDP bridge part) included "sn65dsi86" somewhere in the name instead of just "ti_sn_bridge". Signed-off-by: -
Douglas Anderson authored
In preparation for splitting this driver into sub-drivers, let's rename the main data structure so it's clear that it's holding data for the whole device and not just the MIPI-eDP bridge part. This is a no-op change. Signed-off-by:
-
Thomas Zimmermann authored
The field pdev in struct drm_device is unused. Remove it. The value can be obtained by upcasting from the structure's dev field. Signed-off-by:
Thomas Zimmermann <tzimmermann@suse.de> Reviewed-by:
Maxime Ripard <maxime@cerno.tech> Link: https://patchwork.freedesktop.org/patch/msgid/20210502104953.21768-8-tzimmermann@suse.de
-
Thomas Zimmermann authored
Replace all references to struct drm_device's pdev field with an upcast from dev. Signed-off-by:
-
Thomas Zimmermann authored
Replace all references to struct drm_device's pdev field with an upcast from dev. Signed-off-by:
-
Thomas Zimmermann authored
Replace all references to struct drm_device's pdev field with an upcast from dev. Signed-off-by:
-
Thomas Zimmermann authored
Replace all references to struct drm_device's pdev field with an upcast from dev. Signed-off-by:
-
Thomas Zimmermann authored
Replace all references to struct drm_device's pdev field with an upcast from dev. Signed-off-by:
-
Thomas Zimmermann authored
Replace all references to struct drm_device's pdev field with an upcast from dev. Signed-off-by:
-
Christian König authored
Drop the special handling here. Signed-off-by:
-
Christian König authored
Init all fields in ttm_resource_alloc() when we create a new resource. v2: use place->mem_type instead of res->mem_type Signed-off-by:
-
Christian König authored
Add a separate manager for the system domain and make function tables mandatory. v2: debug is still optional v3: return void during init Signed-off-by:
-
Christian König authored
Audit the includes and stop accessing the internal drm_mm_node. The ttm_resource::start is the same value as the drm_mm_node::start. Signed-off-by:
Michael J. Ruhl <michael.j.ruhl@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210426175824.122557-1-christian.koenig@amd.com
-
Simon Ser authored
Force-probing a connector can be slow and cause flickering. As this affects the global KMS state, let's make it so only the DRM master can force-probe a connector. Non-master DRM clients won't be able to force-probe a connector anymore. Instead, KMS will perform a regular read-only connector query. Signed-off-by:
Simon Ser <contact@emersion.fr> Acked-by:
Pekka Paalanen <pekka.paalanen@collabora.com> Reviewed-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Link: https://patchwork.freedesktop.org/patch/msgid/20210402112212.5625-1-contact@emersion.fr
-
- 01 May, 2021 5 commits
-
-
Thomas Zimmermann authored
We register the simplekms device with the DRM platform helpers. A native driver for the graphics hardware will kick-out the simpledrm driver before taking over the device. The original generic platform device from the simple-framebuffer boot code will be unregistered. The native driver will use whatever native hardware device it received. v4: * convert to drm_aperture_acquire_from_firmware() v3: * use platform_device_unregister() and handle detachment like hot-unplug event (Daniel) v2: * adapt to aperture changes * use drm_dev_unplug() and drm_dev_enter/exit() * don't split error string Signed-off-by:
nerdopolis <bluescreen_avenger@verizon.net> Link: https://patchwork.freedesktop.org/patch/msgid/20210430105840.30515-10-tzimmermann@suse.de
-
Thomas Zimmermann authored
The simpledrm driver is a DRM driver for simple-framebuffer framebuffers as provided by the kernel's boot code. This driver enables basic graphical output on many different graphics devices that are provided by the platform (e.g., EFI, VESA, embedded framebuffers). With the kernel's simple-framebuffer infrastructure, the kernel receives a pre-configured framebuffer from the system (i.e., firmware, boot loader). It creates a platform device to which simpledrm attaches. The system's framebuffer consists of a memory range, size and format. Based on these values, simpledrm creates a DRM devices. No actual modesetting is possible. A firmware framebuffer might also be specified via device-tree files. If no device platform data is given, try the DT device node. Make sure required hardware clocks and regulators are enabled while the firmware framebuffer is in use. The basic code has been taken from the simplefb driver and adapted to DRM. Clocks are released automatically via devres helpers. The drivers displays a console on simpledrm's framebuffer. The default framebuffer format is being used. v4: * disable simplefb if simpledrm has been selected (Maxime) v3: * add disable function that clears screen to black (Daniel) * set shadow buffering only for fbdev emulation * set platform-driver data during device creation v2: * rename driver to simpledrm * add dri-devel to MAINTAINERS entry * put native format first in primary-plane format list (Daniel) * inline simplekms_device_cleanup() (Daniel) * use helpers for shadow-buffered planes * fix whitespace errors * add Device Tree match table * clean-up parser wrappers * use strscpy() Signed-off-by:
-
Thomas Zimmermann authored
Platform devices might operate on firmware framebuffers, such as VESA or EFI. Before a native driver for the graphics hardware can take over the device, it has to remove any platform driver that operates on the firmware framebuffer. Aperture helpers provide the infrastructure for platform drivers to acquire firmware framebuffers, and for native drivers to remove them later on. It works similar to the related fbdev mechanism. During initialization, the platform driver acquires the firmware framebuffer's I/O memory and provides a callback to be removed. The native driver later uses this information to remove any platform driver for it's framebuffer I/O memory. The aperture removal code is integrated into the existing code for removing conflicting framebuffers, so native drivers use it automatically. v5: * fix build error introduced by rebasing v4 * fix typo in documentation v4: * hide detach callback in implementation (Daniel) * documentation fixes v3: * rebase onto existing aperture infrastructure * release aperture from list during detach; fix dangling apertures * don't export struct drm_aperture * document struct drm_aperture_funcs v2: * rename plaform helpers to aperture helpers * tie to device lifetime with devm_ functions * removed unsued remove() callback * rename kickout to detach * make struct drm_aperture private * rebase onto existing drm_aperture.h header file * use MIT license only for simplicity * documentation Signed-off-by:
-
Thomas Zimmermann authored
The blitter functions copy a framebuffer to I/O memory using one of the existing conversion functions. Signed-off-by:
-
Thomas Zimmermann authored
The memcpy's destination buffer might have a different pitch than the source. Support different pitches as function argument. Signed-off-by:
-
- 30 Apr, 2021 3 commits
-
-
Nikola Cornij authored
[why] Previously used value was not safe to provide the correct value, i.e. it could be 0 if not not configured, leading to no MST on this platform. [how] Do not use the value from BIOS, but from the structure populated at encoder initialization time. Fixes: 98025a62 ("drm/dp_mst: Use Extended Base Receiver Capability DPCD space") Signed-off-by:
Nikola Cornij <nikola.cornij@amd.com> Reviewed-by:
Lyude Paul <lyude@redhat.com> Acked-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> [fixed open coded drm_dp_link_rate_to_bw_code()] Signed-off-by:
-
Douglas Anderson authored
In commit 3235b0f2 ("drm/panel: panel-simple: Use runtime pm to avoid excessive unprepare / prepare") we started using pm_runtime, but my patch neglected to add the proper pm_runtime_disable(). Doh! Add them now. Fixes: 3235b0f2 ("drm/panel: panel-simple: Use runtime pm to avoid excessive unprepare / prepare") Reported-by:
-
Liu Ying authored
Some MIPI DSI panel drivers like 'raydium,rm68200' send MIPI_DCS_SET_DISPLAY_ON commands in panel_funcs->prepare(), which requires the MIPI DSI controller and PHY to be ready beforehand. Without this patch, the nwl-dsi driver gets the MIPI DSI controller and PHY ready in bridge_funcs->atomic_pre_enable(), which happens after the panel_funcs->prepare(). So, this patch shifts the bridge operation ealier from bridge_funcs->atomic_pre_enable() to bridge_funcs->mode_set(). This way, more MIPI DSI panels can connect to this nwl-dsi bridge. Cc: Andrzej Hajda <a.hajda@samsung.com> Cc: Neil Armstrong <narmstrong@baylibre.com> Cc: Robert Foss <robert.foss@linaro.org> Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com> Cc: Jonas Karlman <jonas@kwiboo.se> Cc: Jernej Skrabec <jernej.skrabec@siol.net> Cc: David Airlie <airlied@linux.ie> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: Guido Günther <agx@sigxcpu.org> Cc: Robert Chiras <robert.chiras@nxp.com> Cc: NXP Linux Team <linux-imx@nxp.com> Signed-off-by:
Liu Ying <victor.liu@nxp.com> Reviewed-by:
Neil Armstrong <narmstrong@baylibre.com> Signed-off-by:
-
