- 16 Jan, 2015 21 commits
-
-
Jarkko Nikula authored
commit 48826ee5 upstream. Commit 5fe5b767 ("ASoC: dapm: Do not pretend to support controls for non mixer/mux widgets") revealed ill-defined control in a route between "STENL Mux" and DACs in max98090.c: max98090 i2c-193C9890:00: Control not supported for path STENL Mux -> [NULL] -> DACL max98090 i2c-193C9890:00: ASoC: no dapm match for STENL Mux --> NULL --> DACL max98090 i2c-193C9890:00: ASoC: Failed to add route STENL Mux -> NULL -> DACL max98090 i2c-193C9890:00: Control not supported for path STENL Mux -> [NULL] -> DACR max98090 i2c-193C9890:00: ASoC: no dapm match for STENL Mux --> NULL --> DACR max98090 i2c-193C9890:00: ASoC: Failed to add route STENL Mux -> NULL -> DACR Since there is no control between "STENL Mux" and DACs the control name must be NULL not "NULL". Signed-off-by:
Jarkko Nikula <jarkko.nikula@linux.intel.com> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Lars-Peter Clausen authored
commit 50c0f21b upstream. Make sure to check the version field of the firmware header to make sure to not accidentally try to parse a firmware file with a different layout. Trying to do so can result in loading invalid firmware code to the device. Signed-off-by:
Lars-Peter Clausen <lars@metafoo.de> Signed-off-by:
-
Takashi Iwai authored
commit 077661b6 upstream. The of_node_put() call in eukrea_tlv320_probe() may take an uninitialized pointer, as compiler spotted out: sound/soc/fsl/eukrea-tlv320.c:221:14: warning: 'ssi_np' may be used uninitialized in this function [-Wuninitialized] This patch adds the proper NULL initializations as a fix. (codec_np is also NULL initialized just for consistency.) Fixes: 66f23290 ('ASoC: eukrea-tlv320: Add DT support') Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Felix Fietkau authored
commit 9e4982f6 upstream. Like with ath9k, ath5k queues also need to be ordered by priority. queue_info->tqi_subtype already contains the correct index, so use it instead of relying on the order of ath5k_hw_setup_tx_queue calls. Signed-off-by:
Felix Fietkau <nbd@openwrt.org> Signed-off-by:
John W. Linville <linville@tuxdriver.com> Signed-off-by:
-
Emmanuel Grumbach authored
commit 55fd1ce8 upstream. A few device IDs were added, reflect this change in the driver. Signed-off-by:
Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by:
-
Emmanuel Grumbach authored
commit b4c82adc upstream. Interoperability issues were identified and root caused to the Smart Fifo watermarks. These issues arose with NetGear R7000. Fix this. Fixes: 1f3b0ff8 ("iwlwifi: mvm: Add Smart FIFO support") Reviewed-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Emmanuel Grumbach authored
commit 5a12a07e upstream. Since the commit below, iwldvm sends the FLUSH command to the firmware. All the devices that use iwldvm have a firmware that expects the _v3 version of this command, besides 5150. 5150's latest available firmware still expects a _v2 version of the FLUSH command. This means that since the commit below, we had a mismatch for this specific device only. This mismatch led to the NMI below: Loaded firmware version: 8.24.2.2 Start IWL Error Log Dump: Status: 0x0000004C, count: 5 0x00000004 | NMI_INTERRUPT_WDG 0x000006F4 | uPc 0x000005BA | branchlink1 0x000006F8 | branchlink2 0x000008C2 | interruptlink1 0x00005B02 | interruptlink2 0x00000002 | data1 0x07030000 | data2 0x00000068 | line 0x3E80510C | beacon time 0x728A0EF4 | tsf low 0x0000002A | tsf hi 0x00000000 | time gp1 0x01BDC977 | time gp2 0x00000000 | time gp3 0x00010818 | uCode version 0x00000000 | hw version 0x00484704 | board version 0x00000002 | hcmd 0x2FF23080 | isr0 0x0103E000 | isr1 0x0000001A | isr2 0x1443FCC3 | isr3 0x11800112 | isr4 0x00000068 | isr_pref 0x000000D4 | wait_event 0x00000000 | l2p_control 0x00000007 | l2p_duration 0x00103040 | l2p_mhvalid 0x00000007 | l2p_addr_match 0x00000000 | lmpm_pmg_sel 0x00000000 | timestamp 0x00000200 | flow_handler This was reported here: https://bugzilla.kernel.org/show_bug.cgi?id=88961 Fixes: a0855054 ("iwlwifi: dvm: drop non VO frames when flushing") Signed-off-by:
-
Stefano Stabellini authored
commit 2c3fc8d2 upstream. Need to pass the pointer within the swiotlb internal buffer to the swiotlb library, that in the case of xen_unmap_single is dev_addr, not paddr. Signed-off-by:
Stefano Stabellini <stefano.stabellini@eu.citrix.com> Acked-by:
Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by:
-
Stefano Stabellini authored
commit 9490c6c6 upstream. In xen_swiotlb_sync_single we always call xen_dma_sync_single_for_cpu, even when we should call xen_dma_sync_single_for_device. Fix that. Signed-off-by:
-
Stefano Stabellini authored
commit c884227e upstream. On x86 truncation cannot occur because config XEN depends on X86_64 || (X86_32 && X86_PAE). On ARM truncation can occur without CONFIG_ARM_LPAE, when the dma operation involves foreign grants. However in that case the physical address returned by xen_bus_to_phys is actually invalid (there is no mfn to pfn tracking for foreign grants on ARM) and it is not used. Signed-off-by:
Catalin Marinas <catalin.marinas@arm.com> Acked-by:
-
Stefano Stabellini authored
commit d6883e6f upstream. xen_dma_unmap_page and xen_dma_sync_single_for_cpu take a dma_addr_t handle as argument, not a physical address. Signed-off-by:
-
Stephane Grosjean authored
commit dc50ddcd upstream. This patchs fixes a misplaced call to memset() that fills the request buffer with 0. The problem was with sending PCAN_USBPRO_REQ_FCT requests, the content set by the caller was thus lost. With this patch, the memory area is zeroed only when requesting info from the device. Signed-off-by:
Stephane Grosjean <s.grosjean@peak-system.com> Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by:
-
Stephane Grosjean authored
commit af35d0f1 upstream. This patch sets the correct reverse sequence order to the instructions set to run, when any failure occurs during the initialization steps. It also adds the missing unregistration call of the can device if the failure appears after having been registered. Signed-off-by:
-
Felix Fietkau authored
commit 78063d81 upstream. Hardware queues are ordered by priority. Use queue index 0 for BK, which has lower priority than BE. Signed-off-by:
-
Felix Fietkau authored
commit ad8fdccf upstream. The driver passes the desired hardware queue index for a WMM data queue in qinfo->tqi_subtype. This was ignored in ath9k_hw_setuptxqueue, which instead relied on the order in which the function is called. Reported-by:
Hubert Feurstein <h.feurstein@gmail.com> Signed-off-by:
-
Xue jiufei authored
commit 53dc20b9 upstream. In ocfs2_link(), the parent directory inode passed to function ocfs2_lookup_ino_from_name() is wrong. Parameter dir is the parent of new_dentry not old_dentry. We should get old_dir from old_dentry and lookup old_dentry in old_dir in case another node remove the old dentry. With this change, hard linking works again, when paths are relative with at least one subdirectory. This is how the problem was reproducable: # mkdir a # mkdir b # touch a/test # ln a/test b/test ln: failed to create hard link `b/test' => `a/test': No such file or directory However when creating links in the same dir, it worked well. Now the link gets created. Fixes: 0e048316 ("ocfs2: check existence of old dentry in ocfs2_link()") Signed-off-by:
joyce.xue <xuejiufei@huawei.com> Reported-by:
Szabo Aron - UBIT <aron@ubit.hu> Cc: Mark Fasheh <mfasheh@suse.com> Cc: Joel Becker <jlbec@evilplan.org> Tested-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Junxiao Bi authored
commit 136f49b9 upstream. For buffer write, page lock will be got in write_begin and released in write_end, in ocfs2_write_end_nolock(), before it unlock the page in ocfs2_free_write_ctxt(), it calls ocfs2_run_deallocs(), this will ask for the read lock of journal->j_trans_barrier. Holding page lock and ask for journal->j_trans_barrier breaks the locking order. This will cause a deadlock with journal commit threads, ocfs2cmt will get write lock of journal->j_trans_barrier first, then it wakes up kjournald2 to do the commit work, at last it waits until done. To commit journal, kjournald2 needs flushing data first, it needs get the cache page lock. Since some ocfs2 cluster locks are holding by write process, this deadlock may hung the whole cluster. unlock pages before ocfs2_run_deallocs() can fix the locking order, also put unlock before ocfs2_commit_trans() to make page lock is unlocked before j_trans_barrier to preserve unlocking order. Signed-off-by:
Junxiao Bi <junxiao.bi@oracle.com> Reviewed-by:
Wengang Wang <wen.gang.wang@oracle.com> Reviewed-by:
Mark Fasheh <mfasheh@suse.de> Cc: Joel Becker <jlbec@evilplan.org> Signed-off-by:
-
Arnaud Ebalard authored
commit 5945b288 upstream. When Intersil ISL12057 support was added by commit 70e12337 ("rtc: Add support for Intersil ISL12057 I2C RTC chip"), two masks for time registers values imported from the device were either wrong or omitted, leading to additional bits from those registers to impact read values: - mask for hour register value when reading it in AM/PM mode. As AM/PM mode is not the usual mode used by the driver, this error would only have an impact on an externally configured RTC hour later read by the driver. - mask for month value. The lack of masking would provide an erroneous value if century bit is set. This patch fixes those two masks. Fixes: 70e12337 ("rtc: Add support for Intersil ISL12057 I2C RTC chip") Signed-off-by:
Arnaud Ebalard <arno@natisbad.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Peter Huewe <peter.huewe@infineon.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Thierry Reding <treding@nvidia.com> Cc: Mark Brown <broonie@kernel.org> Cc: Grant Likely <grant.likely@linaro.org> Acked-by:
Uwe Kleine-König <uwe@kleine-koenig.org> Signed-off-by:
-
Johan Hovold authored
commit 7ecd9a3f upstream. The platform device must be registered as wakeup capable before registering the class device, or the wakealarm attribute will not be created. Also make sure to unregister the wakeup source on probe errors. Fixes: 1d2e2b65 ("rtc: omap: restore back (hard-code) wakeup support") Signed-off-by:
Johan Hovold <johan@kernel.org> Reviewed-by:
Felipe Balbi <balbi@ti.com> Tested-by:
-
Johan Hovold authored
commit 44c63a57 upstream. This series fixes a few issues with the omap rtc-driver, cleans up a bit, adds device abstraction, and finally adds support for the PMIC control feature found in some revisions of this RTC IP block. Ultimately, this allows for powering off the Beaglebone and waking it up again on RTC alarms. This patch (of 20): Make sure not to reset the clock-source configuration when enabling the 32kHz clock mux. Until the clock source can be configured through device tree we must not overwrite settings made by the bootloader (e.g. clock-source selection). Fixes: cd914bba ("drivers/rtc/rtc-omap.c: add support for enabling 32khz clock") Signed-off-by:
-
Guo Zeng authored
commit 0e953255 upstream. Move rtc register to be later than hardware initialization. The reason is that devm_rtc_device_register() will do read_time() which is a callback accessing hardware. This sometimes causes a hang in the hardware related callback. Signed-off-by:
Guo Zeng <guo.zeng@csr.com> Signed-off-by:
Barry Song <Baohua.Song@csr.com> Cc: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by:
-
- 08 Jan, 2015 19 commits
-
-
Greg Kroah-Hartman authored
-
Filipe Manana authored
commit 678886bd upstream. When we abort a transaction we iterate over all the ranges marked as dirty in fs_info->freed_extents[0] and fs_info->freed_extents[1], clear them from those trees, add them back (unpin) to the free space caches and, if the fs was mounted with "-o discard", perform a discard on those regions. Also, after adding the regions to the free space caches, a fitrim ioctl call can see those ranges in a block group's free space cache and perform a discard on the ranges, so the same issue can happen without "-o discard" as well. This causes corruption, affecting one or multiple btree nodes (in the worst case leaving the fs unmountable) because some of those ranges (the ones in the fs_info->pinned_extents tree) correspond to btree nodes/leafs that are referred by the last committed super block - breaking the rule that anything that was committed by a transaction is untouched until the next transaction commits successfully. I ran into this while running in a loop (for several hours) the fstest that I recently submitted: [PATCH] fstests: add btrfs test to stress chunk allocation/removal and fstrim The corruption always happened when a transaction aborted and then fsck complained like this: _check_btrfs_filesystem: filesystem on /dev/sdc is inconsistent *** fsck.btrfs output *** Check tree block failed, want=94945280, have=0 Check tree block failed, want=94945280, have=0 Check tree block failed, want=94945280, have=0 Check tree block failed, want=94945280, have=0 Check tree block failed, want=94945280, have=0 read block failed check_tree_block Couldn't open file system In this case 94945280 corresponded to the root of a tree. Using frace what I observed was the following sequence of steps happened: 1) transaction N started, fs_info->pinned_extents pointed to fs_info->freed_extents[0]; 2) node/eb 94945280 is created; 3) eb is persisted to disk; 4) transaction N commit starts, fs_info->pinned_extents now points to fs_info->freed_extents[1], and transaction N completes; 5) transaction N + 1 starts; 6) eb is COWed, and btrfs_free_tree_block() called for this eb; 7) eb range (94945280 to 94945280 + 16Kb) is added to fs_info->pinned_extents (fs_info->freed_extents[1]); 8) Something goes wrong in transaction N + 1, like hitting ENOSPC for example, and the transaction is aborted, turning the fs into readonly mode. The stack trace I got for example: [112065.253935] [<ffffffff8140c7b6>] dump_stack+0x4d/0x66 [112065.254271] [<ffffffff81042984>] warn_slowpath_common+0x7f/0x98 [112065.254567] [<ffffffffa0325990>] ? __btrfs_abort_transaction+0x50/0x10b [btrfs] [112065.261674] [<ffffffff810429e5>] warn_slowpath_fmt+0x48/0x50 [112065.261922] [<ffffffffa032949e>] ? btrfs_free_path+0x26/0x29 [btrfs] [112065.262211] [<ffffffffa0325990>] __btrfs_abort_transaction+0x50/0x10b [btrfs] [112065.262545] [<ffffffffa036b1d6>] btrfs_remove_chunk+0x537/0x58b [btrfs] [112065.262771] [<ffffffffa033840f>] btrfs_delete_unused_bgs+0x1de/0x21b [btrfs] [112065.263105] [<ffffffffa0343106>] cleaner_kthread+0x100/0x12f [btrfs] (...) [112065.264493] ---[ end trace dd7903a975a31a08 ]--- [112065.264673] BTRFS: error (device sdc) in btrfs_remove_chunk:2625: errno=-28 No space left [112065.264997] BTRFS info (device sdc): forced readonly 9) The clear kthread sees that the BTRFS_FS_STATE_ERROR bit is set in fs_info->fs_state and calls btrfs_cleanup_transaction(), which in turn calls btrfs_destroy_pinned_extent(); 10) Then btrfs_destroy_pinned_extent() iterates over all the ranges marked as dirty in fs_info->freed_extents[], and for each one it calls discard, if the fs was mounted with "-o discard", and adds the range to the free space cache of the respective block group; 11) btrfs_trim_block_group(), invoked from the fitrim ioctl code path, sees the free space entries and performs a discard; 12) After an umount and mount (or fsck), our eb's location on disk was full of zeroes, and it should have been untouched, because it was marked as dirty in the fs_info->pinned_extents tree, and therefore used by the trees that the last committed superblock points to. Fix this by not performing a discard and not adding the ranges to the free space caches - it's useless from this point since the fs is now in readonly mode and we won't write free space caches to disk anymore (otherwise we would leak space) nor any new superblock. By not adding the ranges to the free space caches, it prevents other code paths from allocating that space and write to it as well, therefore being safer and simpler. This isn't a new problem, as it's been present since 2011 (git commit acce952b). Signed-off-by:
Filipe Manana <fdmanana@suse.com> Signed-off-by:
Chris Mason <clm@fb.com> Signed-off-by:
-
Josef Bacik authored
commit 50d9aa99 upstream. Liu Bo pointed out that my previous fix would lose the generation update in the scenario I described. It is actually much worse than that, we could lose the entire extent if we lose power right after the transaction commits. Consider the following write extent 0-4k log extent in log tree commit transaction < power fail happens here ordered extent completes We would lose the 0-4k extent because it hasn't updated the actual fs tree, and the transaction commit will reset the log so it isn't replayed. If we lose power before the transaction commit we are save, otherwise we are not. Fix this by keeping track of all extents we logged in this transaction. Then when we go to commit the transaction make sure we wait for all of those ordered extents to complete before proceeding. This will make sure that if we lose power after the transaction commit we still have our data. This also fixes the problem of the improperly updated extent generation. Thanks, Signed-off-by:
Josef Bacik <jbacik@fb.com> Signed-off-by:
-
Josef Bacik authored
commit a2804695 upstream. We use the modified list to keep track of which extents have been modified so we know which ones are candidates for logging at fsync() time. Newly modified extents are added to the list at modification time, around the same time the ordered extent is created. We do this so that we don't have to wait for ordered extents to complete before we know what we need to log. The problem is when something like this happens log extent 0-4k on inode 1 copy csum for 0-4k from ordered extent into log sync log commit transaction log some other extent on inode 1 ordered extent for 0-4k completes and adds itself onto modified list again log changed extents see ordered extent for 0-4k has already been logged at this point we assume the csum has been copied sync log crash On replay we will see the extent 0-4k in the log, drop the original 0-4k extent which is the same one that we are replaying which also drops the csum, and then we won't find the csum in the log for that bytenr. This of course causes us to have errors about not having csums for certain ranges of our inode. So remove the modified list manipulation in unpin_extent_cache, any modified extents should have been added well before now, and we don't want them re-logged. This fixes my test that I could reliably reproduce this problem with. Thanks, Signed-off-by:
-
David Sterba authored
commit 0d95c1be upstream. The sizes that are obtained from space infos are in raw units and have to be adjusted according to the raid factor. This was missing for f_bavail and df reported doubled size for raid1. Reported-by:
Martin Steigerwald <Martin@lichtvoll.de> Fixes: ba7b6e62 ("btrfs: adjust statfs calculations according to raid profiles") Signed-off-by:
David Sterba <dsterba@suse.cz> Signed-off-by:
-
Josef Bacik authored
commit 9dba8cf1 upstream. If we have two fsync()'s race on different subvols one will do all of its work to get into the log_tree, wait on it's outstanding IO, and then allow the log_tree to finish it's commit. The problem is we were just free'ing that subvols logged extents instead of waiting on them, so whoever lost the race wouldn't really have their data on disk. Fix this by waiting properly instead of freeing the logged extents. Thanks, Signed-off-by:
-
Michael Halcrow authored
commit 94208064 upstream. Dmitry Chernenkov used KASAN to discover that eCryptfs writes past the end of the allocated buffer during encrypted filename decoding. This fix corrects the issue by getting rid of the unnecessary 0 write when the current bit offset is 2. Signed-off-by:
Michael Halcrow <mhalcrow@google.com> Reported-by:
Dmitry Chernenkov <dmitryc@google.com> Suggested-by:
Kees Cook <keescook@chromium.org> Signed-off-by:
Tyler Hicks <tyhicks@canonical.com> Signed-off-by:
-
Tyler Hicks authored
commit 332b122d upstream. The ecryptfs_encrypted_view mount option greatly changes the functionality of an eCryptfs mount. Instead of encrypting and decrypting lower files, it provides a unified view of the encrypted files in the lower filesystem. The presence of the ecryptfs_encrypted_view mount option is intended to force a read-only mount and modifying files is not supported when the feature is in use. See the following commit for more information: e77a56dd [PATCH] eCryptfs: Encrypted passthrough This patch forces the mount to be read-only when the ecryptfs_encrypted_view mount option is specified by setting the MS_RDONLY flag on the superblock. Additionally, this patch removes some broken logic in ecryptfs_open() that attempted to prevent modifications of files when the encrypted view feature was in use. The check in ecryptfs_open() was not sufficient to prevent file modifications using system calls that do not operate on a file descriptor. Signed-off-by:
Priya Bansal <p.bansal@samsung.com> Signed-off-by:
-
Jan Kara authored
commit e237ec37 upstream. Check that length specified in a component of a symlink fits in the input buffer we are reading. Also properly ignore component length for component types that do not use it. Otherwise we read memory after end of buffer for corrupted udf image. Reported-by:
Carl Henrik Lunde <chlunde@ping.uio.no> Signed-off-by:
Jan Kara <jack@suse.cz> Signed-off-by:
-
Jan Kara authored
commit a1d47b26 upstream. UDF specification allows arbitrarily large symlinks. However we support only symlinks at most one block large. Check the length of the symlink so that we don't access memory beyond end of the symlink block. Reported-by:
Carl Henrik Lunde <chlunde@gmail.com> Signed-off-by:
-
Jan Kara authored
commit e159332b upstream. Verify that inode size is sane when loading inode with data stored in ICB. Otherwise we may get confused later when working with the inode and inode size is too big. Reported-by:
-
Jan Kara authored
commit 0e5cc9a4 upstream. Symlink reading code does not check whether the resulting path fits into the page provided by the generic code. This isn't as easy as just checking the symlink size because of various encoding conversions we perform on path. So we have to check whether there is still enough space in the buffer on the fly. Reported-by:
-
Oleg Nesterov authored
commit 24c037eb upstream. alloc_pid() does get_pid_ns() beforehand but forgets to put_pid_ns() if it fails because disable_pid_allocation() was called by the exiting child_reaper. We could simply move get_pid_ns() down to successful return, but this fix tries to be as trivial as possible. Signed-off-by:
Oleg Nesterov <oleg@redhat.com> Reviewed-by:
"Eric W. Biederman" <ebiederm@xmission.com> Cc: Aaron Tomlin <atomlin@redhat.com> Cc: Pavel Emelyanov <xemul@parallels.com> Cc: Serge Hallyn <serge.hallyn@ubuntu.com> Cc: Sterling Alexander <stalexan@redhat.com> Signed-off-by:
-
Joonsoo Kim authored
commit 6b101e2a upstream. high_memory isn't direct mapped memory so retrieving it's physical address isn't appropriate. But, it would be useful to check physical address of highmem boundary so it's justfiable to get physical address from it. In x86, there is a validation check if CONFIG_DEBUG_VIRTUAL and it triggers following boot failure reported by Ingo. ... BUG: Int 6: CR2 00f06f53 ... Call Trace: dump_stack+0x41/0x52 early_idt_handler+0x6b/0x6b cma_declare_contiguous+0x33/0x212 dma_contiguous_reserve_area+0x31/0x4e dma_contiguous_reserve+0x11d/0x125 setup_arch+0x7b5/0xb63 start_kernel+0xb8/0x3e6 i386_start_kernel+0x79/0x7d To fix boot regression, this patch implements workaround to avoid validation check in x86 when retrieving physical address of high_memory. __pa_nodebug() used by this patch is implemented only in x86 so there is no choice but to use dirty #ifdef. [akpm@linux-foundation.org: tweak comment] Signed-off-by:
Joonsoo Kim <iamjoonsoo.kim@lge.com> Reported-by:
Ingo Molnar <mingo@kernel.org> Tested-by:
-
Jan Kara authored
commit a682e9c2 upstream. If some error happens in NCP_IOC_SETROOT ioctl, the appropriate error return value is then (in most cases) just overwritten before we return. This can result in reporting success to userspace although error happened. This bug was introduced by commit 2e54eb96 ("BKL: Remove BKL from ncpfs"). Propagate the errors correctly. Coverity id: 1226925. Fixes: 2e54eb96 ("BKL: Remove BKL from ncpfs") Signed-off-by:
-
Rabin Vincent authored
commit 7e77bdeb upstream. If a request is backlogged, it's complete() handler will get called twice: once with -EINPROGRESS, and once with the final error code. af_alg's complete handler, unlike other users, does not handle the -EINPROGRESS but instead always completes the completion that recvmsg() is waiting on. This can lead to a return to user space while the request is still pending in the driver. If userspace closes the sockets before the requests are handled by the driver, this will lead to use-after-frees (and potential crashes) in the kernel due to the tfm having been freed. The crashes can be easily reproduced (for example) by reducing the max queue length in cryptod.c and running the following (from http://www.chronox.de/libkcapi.html) on AES-NI capable hardware: $ while true; do kcapi -x 1 -e -c '__ecb-aes-aesni' \ -k 00000000000000000000000000000000 \ -p 00000000000000000000000000000000 >/dev/null & done Signed-off-by:
Rabin Vincent <rabin.vincent@axis.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Richard Guy Briggs authored
commit 041d7b98 upstream. A regression was caused by commit 780a7654: audit: Make testing for a valid loginuid explicit. (which in turn attempted to fix a regression caused by e1760bd5) When audit_krule_to_data() fills in the rules to get a listing, there was a missing clause to convert back from AUDIT_LOGINUID_SET to AUDIT_LOGINUID. This broke userspace by not returning the same information that was sent and expected. The rule: auditctl -a exit,never -F auid=-1 gives: auditctl -l LIST_RULES: exit,never f24=0 syscall=all when it should give: LIST_RULES: exit,never auid=-1 (0xffffffff) syscall=all Tag it so that it is reported the same way it was set. Create a new private flags audit_krule field (pflags) to store it that won't interact with the public one from the API. Signed-off-by:
Richard Guy Briggs <rgb@redhat.com> Signed-off-by:
Paul Moore <pmoore@redhat.com> Signed-off-by:
-
Paul Moore authored
commit 3640dcfa upstream. Commit f1dc4867 ("audit: anchor all pid references in the initial pid namespace") introduced a find_vpid() call when adding/removing audit rules with PID/PPID filters; unfortunately this is problematic as find_vpid() only works if there is a task with the associated PID alive on the system. The following commands demonstrate a simple reproducer. # auditctl -D # auditctl -l # autrace /bin/true # auditctl -l This patch resolves the problem by simply using the PID provided by the user without any additional validation, e.g. no calls to check to see if the task/PID exists. Cc: Richard Guy Briggs <rgb@redhat.com> Signed-off-by:
Eric Paris <eparis@redhat.com> Reviewed-by:
-
Richard Guy Briggs authored
commit 54dc77d9 upstream. Eric Paris explains: Since kauditd_send_multicast_skb() gets called in audit_log_end(), which can come from any context (aka even a sleeping context) GFP_KERNEL can't be used. Since the audit_buffer knows what context it should use, pass that down and use that. See: https://lkml.org/lkml/2014/12/16/542 BUG: sleeping function called from invalid context at mm/slab.c:2849 in_atomic(): 1, irqs_disabled(): 0, pid: 885, name: sulogin 2 locks held by sulogin/885: #0: (&sig->cred_guard_mutex){+.+.+.}, at: [<ffffffff91152e30>] prepare_bprm_creds+0x28/0x8b #1: (tty_files_lock){+.+.+.}, at: [<ffffffff9123e787>] selinux_bprm_committing_creds+0x55/0x22b CPU: 1 PID: 885 Comm: sulogin Not tainted 3.18.0-next-20141216 #30 Hardware name: Dell Inc. Latitude E6530/07Y85M, BIOS A15 06/20/2014 ffff880223744f10 ffff88022410f9b8 ffffffff916ba529 0000000000000375 ffff880223744f10 ffff88022410f9e8 ffffffff91063185 0000000000000006 0000000000000000 0000000000000000 0000000000000000 ffff88022410fa38 Call Trace: [<ffffffff916ba529>] dump_stack+0x50/0xa8 [<ffffffff91063185>] ___might_sleep+0x1b6/0x1be [<ffffffff910632a6>] __might_sleep+0x119/0x128 [<ffffffff91140720>] cache_alloc_debugcheck_before.isra.45+0x1d/0x1f [<ffffffff91141d81>] kmem_cache_alloc+0x43/0x1c9 [<ffffffff914e148d>] __alloc_skb+0x42/0x1a3 [<ffffffff914e2b62>] skb_copy+0x3e/0xa3 [<ffffffff910c263e>] audit_log_end+0x83/0x100 [<ffffffff9123b8d3>] ? avc_audit_pre_callback+0x103/0x103 [<ffffffff91252a73>] common_lsm_audit+0x441/0x450 [<ffffffff9123c163>] slow_avc_audit+0x63/0x67 [<ffffffff9123c42c>] avc_has_perm+0xca/0xe3 [<ffffffff9123dc2d>] inode_has_perm+0x5a/0x65 [<ffffffff9123e7ca>] selinux_bprm_committing_creds+0x98/0x22b [<ffffffff91239e64>] security_bprm_committing_creds+0xe/0x10 [<ffffffff911515e6>] install_exec_creds+0xe/0x79 [<ffffffff911974cf>] load_elf_binary+0xe36/0x10d7 [<ffffffff9115198e>] search_binary_handler+0x81/0x18c [<ffffffff91153376>] do_execveat_common.isra.31+0x4e3/0x7b7 [<ffffffff91153669>] do_execve+0x1f/0x21 [<ffffffff91153967>] SyS_execve+0x25/0x29 [<ffffffff916c61a9>] stub_execve+0x69/0xa0 Reported-by:
Valdis Kletnieks <Valdis.Kletnieks@vt.edu> Signed-off-by:
-
