Acquire the /RESET GPIO before we enable regulators and hold the device
in reset while the regulators power up in order to improve robustness
during the initial power up.

Also fix the error path so that the device is left in reset while we're
at it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Registers which have defaults and are updated by the patch file should
have their defaults updated to match the value set by the patch file,
otherwise incorrect values will be read from the cache.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This patch deactivates the standard, currently noop, boot sequence
because we now have facilities in place for running a custom boot
sequence.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This patch adds facilities for apply a register patch contained within
the chip using the write sequencer.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Factor out the polling of the interrupt status register whilst we wait
for boot done to allow the polling to be reused in other situations.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Future updates will require us to manually apply the register patch for
wm5102.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Only the lowest three bits contain device revision for WM5102, the high
bits have been repurposed.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

If we have a directly provided 32kHz clock unconditionally enable it,
substantial chip functionality relies on it so dynamic management is
not worthwhile.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

MCLK1 is not in the AoD power domain so if it is used as the 32kHz clock
source we need to hold a runtime PM reference to keep the device from going
into low power mode.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

If no irq_flags are passed in platform data then query the interrupt
controller for the trigger type and try to use that. This provides
default operation with a wider range of hardware and will be needed
for device tree support where the interrupt flags are configured on
the interrupt controller.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

If a GPIO is specified for the chip IRQ line then request it. This
improves support for systems that do not put pins into input mode when
used as interrupts.

Also use this GPIO when the primary IRQ is in edge triggered mode to
detect if we have handled pending interrupts in order to improve
robustness.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Allow the user to configure edge triggered IRQs, though we do not yet
fully handle new interrupts occurring while an interrupt is being handled.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

regmap has a very similar looking error, help identify where the error
comes from by changing the error message.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Make sure that we don't leave the device enabled needlessly.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

'patch_regs' cannot be used uninitialized in wm8994_device_init(),
because 'patch_regs' was already guarded by 'regmap_patch'.
Thus, that's a bogus warning.

Without this patch, the build warning happens as below:

drivers/mfd/wm8994-core.c: In function 'wm8994_i2c_probe':
drivers/mfd/wm8994-core.c:595:7: warning: 'patch_regs' may be used uninitialized in this function [-Wuninitialized]
drivers/mfd/wm8994-core.c:408:14: note: 'patch_regs' was declared here
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

'data' is a pointer and hence use NULL instead of 0.
Silences the following warning:
drivers/mfd/max77686.c:49:50: warning: Using plain integer as NULL pointer
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

module_i2c_driver() removes some boilerplate and makes the code
simple.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Conflicts:
	drivers/mfd/ab8500-gpadc.c
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

When rtsx_pci_acquire_irq fails in rtsx_pci_probe, we forget to
disable an MSI (if we enabled it). This results in this warning on the
next attempt to load the module:
WARNING: at drivers/pci/msi.c:834 pci_enable_msi_block+0x2a4/0x2b0()
Hardware name: HP EliteBook 840 G1
Modules linked in: rtsx_pci(+) ...
Pid: 4056, comm: modprobe Tainted: G          I  3.8.0-9405-gd895cb1a-1-vanilla #1
Call Trace:
 [<ffffffff81045c6a>] warn_slowpath_common+0x7a/0xc0
 [<ffffffff81045cc5>] warn_slowpath_null+0x15/0x20
 [<ffffffff81302544>] pci_enable_msi_block+0x2a4/0x2b0
 [<ffffffffa05e335a>] rtsx_pci_probe+0x55a/0x720 [rtsx_pci]
...

So properly disable MSI in that case.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Move the AB8500 Kconfig fragment below the AB3100 so the
menuconfig menu gets hierarchically nested and looks nice.
Having the EZX PCAP in the middle disturbs the nice
hierarchical layout from kconfig.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This patch uses module_platform_driver_probe() macro which makes
the code smaller and simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This patch uses module_platform_driver_probe() macro which makes
the code smaller and simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This patch uses module_platform_driver_probe() macro which makes
the code smaller and simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This patch augments the STMP driver to read the device id
from the stmpe-i2c dt alias if present.

Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

If there is no interrupt property into stmpe node
then activate the no-irq mode by setting the irq
value to -1.

Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This patch allow using syscon driver from the platform data, i.e.
possibility using driver on systems without oftree support.
For search syscon device from the client drivers,
"syscon_regmap_lookup_by_pdevname" function was added.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

DT node properties should not have "_". Replacing them by "-".
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Add Flat Device Tree support to the AS3711 MFD driver. This patch just
allows to bind the driver to I2C devices, instantiated from the DT.
DT support for AS3711 cell drivers will be added in separate drivers.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Reviwed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

CONFIG_MFD_CROS_EC requires CONFIG_MFD_CORE for a couple of functions that
are declared but not defined:

	ERROR: "mfd_remove_devices" [drivers/mfd/cros_ec.ko] undefined!
	ERROR: "mfd_add_devices" [drivers/mfd/cros_ec.ko] undefined!

Fix it by selecting CONFIG_MFD_CORE anytime CONFIG_MFD_CROS_EC is enabled.
Signed-off-by: David Rientjes <rientjes@google.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

To silent those:

 CC [M]  drivers/mfd/cros_ec_spi.o
drivers/mfd/cros_ec_spi.c: In function ‘cros_ec_spi_receive_response’:
drivers/mfd/cros_ec_spi.c:123:5: warning: format ‘%d’ expects argument of type
‘int’, but argument 4 has type ‘long int’ [-Wformat]
drivers/mfd/cros_ec_spi.c:157:3: warning: format ‘%d’ expects argument of type
‘int’, but argument 6 has type ‘long int’ [-Wformat]
drivers/mfd/cros_ec_spi.c:181:2: warning: format ‘%d’ expects argument of type
‘int’, but argument 4 has type ‘long int’ [-Wformat]
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

In order to fix those, when all cros code is modular:

ERROR: "cros_ec_prepare_tx" [drivers/mfd/cros_ec_spi.ko] undefined!
ERROR: "cros_ec_register" [drivers/mfd/cros_ec_spi.ko] undefined!
ERROR: "cros_ec_remove" [drivers/mfd/cros_ec_spi.ko] undefined!
ERROR: "cros_ec_suspend" [drivers/mfd/cros_ec_spi.ko] undefined!
ERROR: "cros_ec_resume" [drivers/mfd/cros_ec_spi.ko] undefined!
ERROR: "cros_ec_register" [drivers/mfd/cros_ec_i2c.ko] undefined!
ERROR: "cros_ec_remove" [drivers/mfd/cros_ec_i2c.ko] undefined!
ERROR: "cros_ec_suspend" [drivers/mfd/cros_ec_i2c.ko] undefined!
ERROR: "cros_ec_resume" [drivers/mfd/cros_ec_i2c.ko] undefined!
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Use the key-matrix layer to interpret key scan information from the EC
and inject input based on the FDT-supplied key map. This driver registers
itself with the ChromeOS EC driver to perform communications.

The matrix-keypad FDT binding is used with a small addition to control
ghosting.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Luigi Semenzato <semenzato@chromium.org>
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

We now have a binding which adds two parameters to the matrix keypad DT
node. This is separate from the GPIO-driven matrix keypad binding, and
unfortunately incompatible, since that uses row-gpios/col-gpios for the
row and column counts.

So the easiest option here is to provide a function for non-GPIO drivers
to use to decode the binding.

Note: We could in fact create an entirely separate structure to hold
these two fields, but it does not seem worth it, yet. If we have more
parameters then we can add this, and then refactor each driver to hold
such a structure.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Tested-by: Sourav Poddar <sourav.poddar@ti.com> (v2)
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This uses a SPI bus to talk to the ChromeOS EC. The protocol
is defined by the EC and is fairly simple, with a length byte,
checksum, command byte and version byte (to permit easy creation
of new commands).
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This uses an I2C bus to talk to the ChromeOS EC. The protocol
is defined by the EC and is fairly simple, with a length byte,
checksum, command byte and version byte (to permit easy creation
of new commands).
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Che-Liang Chiou <clchiou@chromium.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This is the base EC implementation, which provides a high level
interface to the EC for use by the rest of the kernel. The actual
communcations is dealt with by a separate protocol driver which
registers itself with this interface.

Interrupts are passed on through a notifier.

A simple message structure is used to pass messages to the
protocol driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Che-Liang Chiou <clchiou@chromium.org>
Signed-off-by: Jonathan Kliegman <kliegs@chromium.org>
Signed-off-by: Luigi Semenzato <semenzato@chromium.org>
Signed-off-by: Olof Johansson <olofj@chromium.org>
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>