"Helps debug funky firmware issues".

After:
  Starting Linux PPC64 #108 SMP Wed Aug 6 19:04:51 EST 2014
  -----------------------------------------------------
  ppc64_pft_size    = 0x1a
  phys_mem_size     = 0x200000000
  cpu_features      = 0x17fc7a6c18500249
    possible        = 0x1fffffff18700649
    always          = 0x0000000000000040
  cpu_user_features = 0xdc0065c2 0xee000000
  mmu_features      = 0x5a000001
  firmware_features = 0x00000001405a440b
  htab_hash_mask    = 0x7ffff
  -----------------------------------------------------
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

At boot we display a bunch of low level settings which can be useful to
know, and can help to spot bugs when things are fundamentally
misconfigured.

At the moment they are very widely spaced, so that we can accommodate
the line:

  ppc64_caches.dcache_line_size = 0xYY

But we only print that line when the cache line size is not 128, ie.
almost never, so it just makes the display look odd usually.

The ppc64_caches prefix is redundant so remove it, which means we can
align things a bit closer for the common case. While we're there
replace the last use of camelCase (physicalMemorySize), and use
phys_mem_size.

Before:
  Starting Linux PPC64 #104 SMP Wed Aug 6 18:41:34 EST 2014
  -----------------------------------------------------
  ppc64_pft_size                = 0x1a
  physicalMemorySize            = 0x200000000
  ppc64_caches.dcache_line_size = 0xf0
  ppc64_caches.icache_line_size = 0xf0
  htab_address                  = 0xdeadbeef
  htab_hash_mask                = 0x7ffff
  physical_start                = 0xf000bar
  -----------------------------------------------------

After:
  Starting Linux PPC64 #103 SMP Wed Aug 6 18:38:04 EST 2014
  -----------------------------------------------------
  ppc64_pft_size    = 0x1a
  phys_mem_size     = 0x200000000
  dcache_line_size  = 0xf0
  icache_line_size  = 0xf0
  htab_address      = 0xdeadbeef
  htab_hash_mask    = 0x7ffff
  physical_start    = 0xf000bar
  -----------------------------------------------------

This patch is final, no bike shedding ;)
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

We are enabling USB unconditionally which results in following build failure

drivers/built-in.o: In function `tb_drom_read':
(.text+0x1b62b70): undefined reference to `usb_speed_string'
make: *** [vmlinux] Error

Enable USB only if USB_SUPPORT is set to avoid such failures
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
Acked-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Fix the following build failure

drivers/built-in.o: In function `nhi_init':
nhi.c:(.init.text+0x63390): undefined reference to `ehci_init_driver'

by adding a dependency on USB_EHCI_HCD which supplies the ehci_init_driver().

Also we need to depend on USB_OHCI_HCD similarly
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
Acked-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

this patches changes some error handling logics in numa_setup_cpu(),
when cpu node is not found, so:

if the cpu is possible, but not present, -1 is kept in numa_cpu_lookup_table,
so later, if the cpu is added, we could set correct numa information for it.

if the cpu is present, then we set the first online node to
numa_cpu_lookup_table instead of 0 ( in case 0 might not be an online node? )

Cc: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Cc: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
Acked-by: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

As Nish suggested, it makes more sense to init the numa node informatiion
for present cpus at boottime, which could also avoid WARN_ON(1) in
numa_setup_cpu().

With this change, we also need to change the smp_prepare_cpus() to set up
numa information only on present cpus.

For those possible, but not present cpus, their numa information
will be set up after they are started, as the original code did before commit
2fabf084.

Cc: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Cc: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
Acked-by: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Tested-by: Cyril Bur <cyril.bur@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

With commit 2fabf084 ("powerpc: reorder per-cpu NUMA information's
initialization"), during boottime, cpu_numa_callback() is called
earlier(before their online) for each cpu, and verify_cpu_node_mapping()
uses cpu_to_node() to check whether siblings are in the same node.

It skips the checking for siblings that are not online yet. So the only
check done here is for the bootcpu, which is online at that time. But
the per-cpu numa_node cpu_to_node() uses hasn't been set up yet (which
will be set up in smp_prepare_cpus()).

So I saw something like following reported:
[    0.000000] CPU thread siblings 1/2/3 and 0 don't belong to the same
node!

As we don't actually do the checking during this early stage, so maybe
we could directly call numa_setup_cpu() in do_init_bootmem().

Cc: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Cc: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
Acked-by: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

The size field of the op.type word is now the total number of bytes
to be loaded or stored.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

This extends the instruction emulation done by analyse_instr() and
emulate_step() to handle a few more instructions that are found in
the kernel.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

This splits out the instruction analysis part of emulate_step() into
a separate analyse_instr() function, which decodes the instruction,
but doesn't execute any load or store instructions.  It does execute
integer instructions and branches which can be executed purely by
updating register values in the pt_regs struct.  For other instructions,
it returns the instruction type and other details in a new
instruction_op struct.  emulate_step() then uses that information
to execute loads, stores, cache operations, mfmsr, mtmsr[d], and
(on 64-bit) sc instructions.

The reason for doing this is so that the KVM code can use it instead
of having its own separate instruction emulation code.  Possibly the
alignment interrupt handler could also use this.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

In commit e6a6928c "of/fdt: Convert FDT functions to use libfdt",
the kernel stopped supporting old flat device tree formats. The minimum
supported version is now 0x10.

There was a checking function added, early_init_dt_verify(), but it's
not called on powerpc.

The result is, if you boot with an old flat device tree, the kernel will
fail to parse it correctly, think you have no memory etc. and hilarity
ensues.

We can't really fix it, but we can at least catch the fact that the
device tree is in an unsupported format and panic(). We can't call
BUG(), it's too early.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

On PowerNV platforms, when a CPU is offline, we put it into nap mode.
It's possible that the CPU wakes up from nap mode while it is still
offline due to a stray IPI.  A misdirected device interrupt could also
potentially cause it to wake up.  In that circumstance, we need to clear
the interrupt so that the CPU can go back to nap mode.

In the past the clearing of the interrupt was accomplished by briefly
enabling interrupts and allowing the normal interrupt handling code
(do_IRQ() etc.) to handle the interrupt.  This has the problem that
this code calls irq_enter() and irq_exit(), which call functions such
as account_system_vtime() which use RCU internally.  Use of RCU is not
permitted on offline CPUs and will trigger errors if RCU checking is
enabled.

To avoid calling into any generic code which might use RCU, we adopt
a different method of clearing interrupts on offline CPUs.  Since we
are on the PowerNV platform, we know that the system interrupt
controller is a XICS being driven directly (i.e. not via hcalls) by
the kernel.  Hence this adds a new icp_native_flush_interrupt()
function to the native-mode XICS driver and arranges to call that
when an offline CPU is woken from nap.  This new function reads the
interrupt from the XICS.  If it is an IPI, it clears the IPI; if it
is a device interrupt, it prints a warning and disables the source.
Then it does the end-of-interrupt processing for the interrupt.

The other thing that briefly enabling interrupts did was to check and
clear the irq_happened flag in this CPU's PACA.  Therefore, after
flushing the interrupt from the XICS, we also clear all bits except
the PACA_IRQ_HARD_DIS (interrupts are hard disabled) bit from the
irq_happened flag.  The PACA_IRQ_HARD_DIS flag is set by power7_nap()
and is left set to indicate that interrupts are hard disabled.  This
means we then have to ignore that flag in power7_nap(), which is
reasonable since it doesn't indicate that any interrupt event needs
servicing.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

I ran some tests to compare hash_64 using shifts and multiplies.
The results:

POWER6:	~2x slower
POWER7: ~2x faster
POWER8: ~2x faster

Now we have a proper config option, select
CONFIG_ARCH_HAS_FAST_MULTIPLIER on POWER7 and POWER8.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

This allows the user to build a kernel targeted at POWER8
(ie gcc -mcpu=power8).
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

When removing a cpu, this patch makes sure that values
gotten from or passed to firmware are in the correct
endian format.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

The ibm,ppc-interrupt-server#s property is in big endian format.
These values need to be converted when used by little endian
architectures.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

of_device_ids (i.e. compatible strings and the respective data) are not
supposed to change at runtime. All functions working with of_device_ids
provided by <linux/of.h> work with const of_device_ids. This allows to
mark all struct of_device_id const, too.

While touching these line also put the __init annotation at the right
position where necessary.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

CONFIG_JUMP_LABEL doesn't ensure HAVE_JUMP_LABEL, if it
is not the case use maintainers's own mutex to guard
the modification of global values.
Signed-off-by: Zhouyi Zhou <yizhouzhou@ict.ac.cn>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Fix build error caused by missing export:

ERROR: "dcr_ind_lock" [drivers/net/ethernet/ibm/emac/ibm_emac.ko] undefined!
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

A recent patch added a function prototype for htab_remove_mapping in
c code. Fix it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

There were a number of prototypes for functions that no longer
exist. Remove them.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Fix a number of places where global functions were not including
their prototype. This ensures the prototype and the function match.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Simplify things considerably by moving all the ppc32 specific
symbol exports into its own file.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Move the lib symbol exports closer to their function definitions
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Check that the OPAL_DUMP_READ token exists before initalising the elog
infrastructure.

This avoids littering the OPAL console with:
  "OPAL: Called with bad token 91"
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Check that the OPAL_ELOG_READ token exists before initalising the elog
infrastructure.

This avoids littering the OPAL console with:
  "OPAL: Called with bad token 74"
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Check that the OPAL_RTC_READ token exists before we use the OPAL RTC.

Refactors the code a little to merge error paths.

This avoids littering the OPAL console with:
  "OPAL: Called with bad token 3".
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Currently there is no way to generically check if an OPAL call exists or not
from the host kernel.

This adds an OPAL call opal_check_token() which tells you if the given token is
present in OPAL or not.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Fix ppc 32 build failure as reported here:

http://kisskb.ellerman.id.au/kisskb/buildresult/11663513/

The error is as follows:

arch/powerpc/include/asm/floppy.h:142:20: error: 'isa_bridge_pcidev' undeclared
(first use in this function)

This is happening since floppy.o is enabled by BLK_DEV_FD which depends on
ARCH_MAY_HAVE_PC_FDC which is in-turn enabled if PPC_PSERIES=n.

The following commit changes the dependency so that ARCH_MAY_HAVE_PC_FDC is
dependent exclusively on PCI since otherwise it will not compile.
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
CC: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

in commit 29f1aff2 (powerpc: Copy bootable images in the default
install script) we changed to copying all the built boot targets based
on the assumption that it's backwards compatible.  It turns out that
debian devived installkernel scripts will barf if not given exactly 4
args.

This change reverts make install to just install the vmlinux (we can
change the dfault in a seperate patch) and introduces a new make
zInstall which works with a more flexible installkernel script.

Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Presently we only support initiating Service Processor dump from host.
Hence update sysfs message. Also update couple of other error/info
messages.
Signed-off-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Continue is not needed at the bottom of a loop.

The Coccinelle semantic patch implementing this change is:

@@
@@

for (...;...;...) {
  ...
  if (...) {
    ...
-   continue;
  }
}
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Pull vfs fixes from Al Viro:
 "double iput() on failure exit in lustre, racy removal of spliced
  dentries from ->s_anon in __d_materialise_dentry() plus a bunch of
  assorted RCU pathwalk fixes"

The RCU pathwalk fixes end up fixing a couple of cases where we
incorrectly dropped out of RCU walking, due to incorrect initialization
and testing of the sequence locks in some corner cases.  Since dropping
out of RCU walk mode forces the slow locked accesses, those corner cases
slowed down quite dramatically.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  be careful with nd->inode in path_init() and follow_dotdot_rcu()
  don't bugger nd->seq on set_root_rcu() from follow_dotdot_rcu()
  fix bogus read_seqretry() checks introduced in b37199e6
  move the call of __d_drop(anon) into __d_materialise_unique(dentry, anon)
  [fix] lustre: d_make_root() does iput() on dentry allocation failure