Currently, we don't allow the user to try and rebalance to a dup profile
on a multi-device filesystem.  In most cases, this is a perfectly sensible
restriction as raid1 uses the same amount of space and provides better
protection.

However, when reshaping a multi-device filesystem down to a single device
filesystem, this requires the user to convert metadata and system chunks
to single profile before deleting devices, and then convert again to dup,
which leaves a period of time where metadata integrity is reduced.

This patch removes the single-device-only restriction from converting to
dup profile to remove this potential data integrity reduction.
Signed-off-by: Austin S. Hemmelgarn <ahferroin7@gmail.com>
Signed-off-by: David Sterba <dsterba@suse.com>

Now we force to create empty block group to keep data profile alive,
however, in the below example, we eventually get an empty block group
while we're trying to get more space for other types (metadata/system),

- Before,
block group "A": size=2G, used=1.2G
block group "B": size=2G, used=512M

- After "btrfs balance start -dusage=50 mount_point",
block group "A": size=2G, used=(1.2+0.5)G
block group "C": size=2G, used=0

Since there is no data in block group C, it won't be deleted
automatically and we have to get the unused 2G until the next mount.

Balance itself just moves data and doesn't remove data, so it's safe
to not create such a empty block group if we already have data
 allocated in other block groups.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>

The delalloc reserved space is calculated in terms of number of bytes
used by an integral number of blocks. This is done by rounding down the
value of 'pos' to the nearest multiple of sectorsize.

The file offset value held by 'pos' variable may not be aligned to
sectorsize and hence when passing it as an argument to
btrfs_delalloc_release_space(), we may end up releasing larger delalloc
space than we originally had reserved.
Signed-off-by: Chandan Rajendra <chandan@linux.vnet.ibm.com>
Signed-off-by: David Sterba <dsterba@suse.com>

Now that we bail out immediately if ->writepage() returns an error,
we don't need an extra error to retain the error code.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>

If sequential writer is writing in the middle of the page and it just redirties
the last written page by continuing from it.

In the above case this can end up with seeking back to that firstly redirtied
page after writing all the pages at the end of file because btrfs updates
mapping->writeback_index to 1 past the current one.

For non-cow filesystems, the cost is only about extra seek, while for cow
filesystems such as btrfs, it means unnecessary fragments.

To avoid it, we just need to continue writeback from the last written page.

This also updates btrfs to behave like what write_cache_pages() does, ie, bail
 out immediately if there is an error in writepage().

<Ref: https://www.spinics.net/lists/linux-btrfs/msg52628.html>
Reported-by: Holger Hoffstätte <holger.hoffstaette@googlemail.com>
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>

32-bit ioctl uses these rather than the regular FS_IOC_* versions. They can
be handled in btrfs using the same code. Without this, 32-bit {ch,ls}attr
fail.
Signed-off-by: Luke Dashjr <luke-jr+git@utopios.org>
Cc: stable@vger.kernel.org
Reviewed-by: Josef Bacik <jbacik@fb.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>

Pull thermal fixes from Eduardo Valentin:
 "Specifics in this pull request:

   - Fixes in mediatek and OF thermal drivers

   - Fixes in power_allocator governor

   - More fixes of unsigned to int type change in thermal_core.c.

  These change have been CI tested using KernelCI bot. \o/"

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
  thermal: fix Mediatek thermal controller build
  thermal: consistently use int for trip temp
  thermal: fix mtk_thermal build dependency
  thermal: minor mtk_thermal.c cleanups
  thermal: power_allocator: req_range multiplication should be a 64 bit type
  thermal: of: add __init attribute

Pull asm-generic update from Arnd Bergmann:
 "Here is one patch to wire up the preadv/pwritev system calls in the
  generic system call table, which is required for all architectures
  that were merged in the last few years, including arm64.

  Usually these get merged along with the syscall implementation or one
  of the architecture trees, but this time that did not happen.

  Andre and Christoph both sent a version of this patch, I picked the
  one I got first"

* tag 'asm-generic-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
  generic syscalls: wire up preadv2 and pwritev2 syscalls

These new syscalls are implemented as generic code, so enable them for
architectures like arm64 which use the generic syscall table.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Pull x86 fixes from Ingo Molnar:
 "Misc fixes: two EDAC driver fixes, a Xen crash fix, a HyperV log spam
  fix and a documentation fix"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86 EDAC, sb_edac.c: Take account of channel hashing when needed
  x86 EDAC, sb_edac.c: Repair damage introduced when "fixing" channel address
  x86/mm/xen: Suppress hugetlbfs in PV guests
  x86/doc: Correct limits in Documentation/x86/x86_64/mm.txt
  x86/hyperv: Avoid reporting bogus NMI status for Gen2 instances

Merge branches 'perf-urgent-for-linus', 'smp-urgent-for-linus' and 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip

Pull perf, cpu hotplug and timer fixes from Ingo Molnar:
 "perf:
   - A single tooling fix for a user-triggerable segfault.

  CPU hotplug:
   - Fix a CPU hotplug corner case regression, introduced by the recent
     hotplug rework

  timers:
   - Fix a boot hang in the ARM based Tango SoC clocksource driver"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf intel-pt: Fix segfault tracing transactions

* 'smp-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  cpu/hotplug: Fix rollback during error-out in __cpu_disable()

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  clocksource/drivers/tango-xtal: Fix boot hang due to incorrect test

Pull locking fixes from Ingo Molnar:
 "Misc fixes:

  pvqspinlocks:
   - an instrumentation fix

  futexes:
   - preempt-count vs pagefault_disable decouple corner case fix
   - futex requeue plist race window fix
   - futex UNLOCK_PI transaction fix for a corner case"

* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  asm-generic/futex: Re-enable preemption in futex_atomic_cmpxchg_inatomic()
  futex: Acknowledge a new waiter in counter before plist
  futex: Handle unlock_pi race gracefully
  locking/pvqspinlock: Fix division by zero in qstat_read()

Pull irq fixes from Ingo Molnar:
 "A core irq affinity masks related fix and a MIPS irqchip driver fix"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/mips-gic: Don't overrun pcpu_masks array
  genirq: Dont allow affinity mask to be updated on IPIs

Pull objtool fixes from Ingo Molnar:
 "A handful of objtool fixes: two improvements to how warnings are
  printed plus a false positive warning fix, and build environment fix"

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  objtool: Fix Makefile to properly see if libelf is supported
  objtool: Detect falling through to the next function
  objtool: Add workaround for GCC switch jump table bug

Pull USB / PHY driver fixes from Greg KH:
 "Here are two small sets of patches, both from subsystem trees, USB
  gadget and PHY drivers.

  Full details are in the shortlog, and they have all been in linux-next
  for a while (before I merged them to the USB tree)"

* tag 'usb-4.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  usb: gadget: f_fs: Fix use-after-free
  usb: dwc3: gadget: Fix suspend/resume during device mode
  usb: dwc3: fix memory leak of dwc->regset
  usb: dwc3: core: fix PHY handling during suspend
  usb: dwc3: omap: fix up error path on probe()
  usb: gadget: composite: Clear reserved fields of SSP Dev Cap
  phy: rockchip-emmc: adapt binding to specifiy register offset and length
  phy: rockchip-emmc: should be a child device of the GRF
  phy: rockchip-dp: should be a child device of the GRF

Pull serial fixes from Greg KH:
 "Here are 3 serial driver fixes for issues that have been reported.

  Two are reverts, fixing problems that were in the big TTY/Serial
  driver merge in 4.6-rc1, and the last one is a simple bugfix for a
  regression that showed up in 4.6-rc1 as well.

  All have been in linux-next with no reported issues"

* tag 'tty-4.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  Revert "serial: 8250: Add hardware dependency to RT288X option"
  tty/serial/8250: fix RS485 half-duplex RX
  Revert "serial-uartlite: Constify uartlite_be/uartlite_le"

Pull input subsystem fixes from Dmitry Torokhov:
 "Just minor driver fixes"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: twl4030-vibra - do not reparent to grandparent
  Input: twl6040-vibra - do not reparent to grandparent
  Input: twl6040-vibra - ignore return value of schedule_work
  Input: twl6040-vibra - fix NULL pointer dereference by removing workqueue
  Input: pmic8xxx-pwrkey - fix algorithm for converting trigger delay
  Input: arizona-haptic - don't assign input_dev parent
  Input: clarify we want BTN_TOOL_<name> on proximity
  Input: xpad - add Mad Catz FightStick TE 2 VID/PID
  Input: gtco - fix crash on detecting device without endpoints

Pull pin control fixes from Linus Walleij:
 "Some pin control driver fixes came in.  One headed for stable and the
  other two are just ordinary merge window fixes.

   - Make the i.MX driver select REGMAP as a dependency
   - Fix up the Mediatek debounce time unit
   - Fix a real hairy ffs vs __ffs issue in the Single pinctrl driver"

* tag 'pinctrl-v4.6-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
  pinctrl: single: Fix pcs_parse_bits_in_pinctrl_entry to use __ffs than ffs
  pinctrl: mediatek: correct debounce time unit in mtk_gpio_set_debounce
  pinctrl: imx: Kconfig: PINCTRL_IMX select REGMAP

Pull arm64 fixes from Catalin Marinas:

 - Cache invalidation fix for early CPU boot status update (incorrect
   cacheline)

 - of_put_node() missing in the spin_table code

 - EL1/El2 early init inconsistency when Virtualisation Host Extensions
   are present

 - RCU warning fix in the arm_pmu.c driver

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: Fix EL1/EL2 early init inconsistencies with VHE
  drivers/perf: arm-pmu: fix RCU usage on pmu resume from low-power
  arm64: spin-table: add missing of_node_put()
  arm64: fix invalidation of wrong __early_cpu_boot_status cacheline

Pull powerpc fixes from Michael Ellerman:
 "Three powerpc cpu feature fixes from Anton Blanchard:

   - scan_features() updated incorrect bits for REAL_LE

   - update cpu_user_features2 in scan_features()

   - update TM user feature bits in scan_features()"

* tag 'powerpc-4.6-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc: Update TM user feature bits in scan_features()
  powerpc: Update cpu_user_features2 in scan_features()
  powerpc: scan_features() updates incorrect bits for REAL_LE

Pull IOMMU fixes from Joerg Roedel:
 "The fixes include:

   - Two patches to revert the use of default domains in the ARM SMMU
     driver.  Enabling this caused regressions which need more thorough
     fixing.  So the regressions are fixed for now by disabling the use
     of default domains.

   - A fix for a v4.4 regression in the AMD IOMMU driver which broke
     devices behind invisible PCIe-to-PCI bridges with IOMMU enabled"

* tag 'iommu-fixes-v4.6-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
  iommu/arm-smmu: Don't allocate resources for bypass domains
  iommu/arm-smmu: Fix stream-match conflict with IOMMU_DOMAIN_DMA
  iommu/amd: Fix checking of pci dma aliases

Pull drm fixes from Dave Airlie:
 "i915, nouveau and amdgpu/radeon fixes in this:

  nouveau:
     Two fixes, one for a regression with dithering and one for a bug
     hit by the userspace drivers.

  i915:
     A few fixes, mostly things heading for stable, two important
     skylake GT3/4 hangs.

  radeon/amdgpu:
     Some audio, suspend/resume and some runtime PM fixes, along with
     two patches to harden the userptr ABI a bit"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (24 commits)
  drm: Loongson-3 doesn't fully support wc memory
  drm/nouveau/gr/gf100: select a stream master to fixup tfb offset queries
  amdgpu/uvd: add uvd fw version for amdgpu
  drm/amdgpu: forbid mapping of userptr bo through radeon device file
  drm/radeon: forbid mapping of userptr bo through radeon device file
  drm/amdgpu: bump the afmt limit for CZ, ST, Polaris
  drm/amdgpu: use defines for CRTCs and AMFT blocks
  drm/dp/mst: Validate port in drm_dp_payload_send_msg()
  drm/nouveau/kms: fix setting of default values for dithering properties
  drm/radeon: print a message if ATPX dGPU power control is missing
  Revert "drm/radeon: disable runtime pm on PX laptops without dGPU power control"
  drm/amdgpu/acp: fix resume on CZ systems with AZ audio
  drm/radeon: add a quirk for a XFX R9 270X
  drm/radeon: print pci revision as well as pci ids on driver load
  drm/i915: Use fw_domains_put_with_fifo() on HSW
  drm/i915: Force ringbuffers to not be at offset 0
  drm/i915: Adjust size of PIPE_CONTROL used for gen8 render seqno write
  drm/i915/skl: Fix spurious gpu hang with gt3/gt4 revs
  drm/i915/skl: Fix rc6 based gpu/system hang
  drm/i915/userptr: Hold mmref whilst calling get-user-pages
  ...

Pull sound fixes from Takashi Iwai:
 "Again a relatively calm week without surprise: most of fixes are about
  HD-audio, including fixes for Cirrus codec regression and a race over
  regmap access.  Although both change are slightly unintuitive, the
  risk of further breakage is quite low, I hope.

  Other than that, all the rest are trivial"

* tag 'sound-4.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda - Fix possible race on regmap bypass flip
  ALSA: pcxhr: Fix missing mutex unlock
  ALSA: hda - add PCI ID for Intel Broxton-T
  ALSA: hda - Keep powering up ADCs on Cirrus codecs
  ALSA: hda/realtek - Add ALC3234 headset mode for Optiplex 9020m
  ALSA - hda: hdmi check NULL pointer in hdmi_set_chmap
  ALSA: hda - Don't trust the reported actual power state

Merge tag 'phy-for-4.6-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-linus

Kishon writes:

phy: for 4.6-rc

*) make rockchip-dp and rockchip-emmc PHY child device of
   GRF
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Haswell and Broadwell can be configured to hash the channel
interleave function using bits [27:12] of the physical address.

On those processor models we must check to see if hashing is
enabled (bit21 of the HASWELL_HASYSDEFEATURE2 register) and
act accordingly.

Based on a patch by patrickg <patrickg@supermicro.com>
Tested-by: Patrick Geary <patrickg@supermicro.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Acked-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Aristeu Rozanski <arozansk@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-edac@vger.kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>

In commit:

  eb1af3b7 ("Fix computation of channel address")

I switched the "sck_way" variable from holding the log2 value read
from the h/w to instead be the actual number. Unfortunately it
is needed in log2 form when used to shift the address.
Tested-by: Patrick Geary <patrickg@supermicro.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Acked-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Aristeu Rozanski <arozansk@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-edac@vger.kernel.org
Cc: stable@vger.kernel.org
Fixes: eb1af3b7 ("Fix computation of channel address")
Signed-off-by: Ingo Molnar <mingo@kernel.org>

Merge tag 'fixes-for-v4.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus

Felipe writes:

usb: fixes for v4.6-rc5

No more major fixes left. Out of the 6 fixes we have
here, 4 are on dwc3.

The most important is the memory leak fix in
dwc3/debugfs.c. We also have a fix for PHY handling
in suspend/resume and a fix for dwc3-omap's error
handling.

Suspend/resume also had the potential to trigger a
NULL pointer dereference on dwc3; that's also fixed
now.

Our good ol' ffs function gets a use-after-free fix
while the generic composite.c layer has a robustness
fix by making sure reserved fields of a possible SSP
device capability descriptor is cleared to 0.

Huge pages are not normally available to PV guests. Not suppressing
hugetlbfs use results in an endless loop of page faults when user mode
code tries to access a hugetlbfs mapped area (since the hypervisor
denies such PTEs to be created, but error indications can't be
propagated out of xen_set_pte_at(), just like for various of its
siblings), and - once killed in an oops like this:

  kernel BUG at .../fs/hugetlbfs/inode.c:428!
  invalid opcode: 0000 [#1] SMP
  ...
  RIP: e030:[<ffffffff811c333b>]  [<ffffffff811c333b>] remove_inode_hugepages+0x25b/0x320
  ...
  Call Trace:
   [<ffffffff811c3415>] hugetlbfs_evict_inode+0x15/0x40
   [<ffffffff81167b3d>] evict+0xbd/0x1b0
   [<ffffffff8116514a>] __dentry_kill+0x19a/0x1f0
   [<ffffffff81165b0e>] dput+0x1fe/0x220
   [<ffffffff81150535>] __fput+0x155/0x200
   [<ffffffff81079fc0>] task_work_run+0x60/0xa0
   [<ffffffff81063510>] do_exit+0x160/0x400
   [<ffffffff810637eb>] do_group_exit+0x3b/0xa0
   [<ffffffff8106e8bd>] get_signal+0x1ed/0x470
   [<ffffffff8100f854>] do_signal+0x14/0x110
   [<ffffffff810030e9>] prepare_exit_to_usermode+0xe9/0xf0
   [<ffffffff814178a5>] retint_user+0x8/0x13

This is CVE-2016-3961 / XSA-174.
Reported-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Juergen Gross <JGross@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Luis R. Rodriguez <mcgrof@suse.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Toshi Kani <toshi.kani@hp.com>
Cc: stable@vger.kernel.org
Cc: xen-devel <xen-devel@lists.xenproject.org>
Link: http://lkml.kernel.org/r/57188ED802000078000E431C@prv-mh.provo.novell.comSigned-off-by: Ingo Molnar <mingo@kernel.org>

Correct the size of the module mapping space and the maximum available
physical memory size of current processors.
Signed-off-by: Juergen Gross <jgross@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: corbet@lwn.net
Cc: linux-doc@vger.kernel.org
Link: http://lkml.kernel.org/r/1461310504-15977-1-git-send-email-jgross@suse.comSigned-off-by: Ingo Molnar <mingo@kernel.org>

The recent introduction of the hotplug thread which invokes the callbacks on
the plugged cpu, cased the following regression:

If takedown_cpu() fails, then we run into several issues:

 1) The rollback of the target cpu states is not invoked. That leaves the smp
    threads and the hotplug thread in disabled state.

 2) notify_online() is executed due to a missing skip_onerr flag. That causes
    that both CPU_DOWN_FAILED and CPU_ONLINE notifications are invoked which
    confuses quite some notifiers.

 3) The CPU_DOWN_FAILED notification is not invoked on the target CPU. That's
    not an issue per se, but it is inconsistent and in consequence blocks the
    patches which rely on these states being invoked on the target CPU and not
    on the controlling cpu. It also does not preserve the strict call order on
    rollback which is problematic for the ongoing state machine conversion as
    well.

To fix this we add a rollback flag to the remote callback machinery and invoke
the rollback including the CPU_DOWN_FAILED notification on the remote
cpu. Further mark the notify online state with 'skip_onerr' so we don't get a
double invokation.

This workaround will go away once we moved the unplug invocation to the target
cpu itself.

[ tglx: Massaged changelog and moved the CPU_DOWN_FAILED notifiaction to the
  	target cpu ]

Fixes: 4cb28ced ("cpu/hotplug: Create hotplug threads")
Reported-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: linux-s390@vger.kernel.org
Cc: rt@linutronix.de
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Anna-Maria Gleixner <anna-maria@linutronix.de>
Link: http://lkml.kernel.org/r/20160408124015.GA21960@linutronix.deSigned-off-by: Thomas Gleixner <tglx@linutronix.de>

Commit 0881841f introduced a regression by inverting a test check
after calling clocksource_mmio_init(). That results on the system to
hang at boot time.

Fix it by inverting the test again.

Fixes: 0881841f ("Replace code by clocksource_mmio_init")
Reported-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>

When doing a make allmodconfig, I hit the following compile error:

  In file included from builtin-check.c:32:0:
  elf.h:22:18: fatal error: gelf.h: No such file or directory
  compilation terminated.
  ...

Digging into it, it appears that the $(shell ..) command in the Makefile does
not give the proper result when it fails to find -lelf, and continues to
compile objtool.

Instead, use the "try-run" makefile macro to perform the test. This gives a
proper result for both cases.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Bernd Petrovitsch <bernd@petrovitsch.priv.at>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Chris J Arges <chris.j.arges@canonical.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michal Marek <mmarek@suse.cz>
Cc: Namhyung Kim <namhyung@gmail.com>
Cc: Pedro Alves <palves@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: live-patching@vger.kernel.org
Fixes: 442f04c3 ("objtool: Add tool to perform compile-time stack metadata validation")
Link: http://lkml.kernel.org/r/20160420153234.GA24032@home.goodmis.orgSigned-off-by: Ingo Molnar <mingo@kernel.org>

Misc radeon and amdgpu bug fixes for 4.6.

* 'drm-fixes-4.6' of git://people.freedesktop.org/~agd5f/linux:
  amdgpu/uvd: add uvd fw version for amdgpu
  drm/amdgpu: forbid mapping of userptr bo through radeon device file
  drm/radeon: forbid mapping of userptr bo through radeon device file
  drm/amdgpu: bump the afmt limit for CZ, ST, Polaris
  drm/amdgpu: use defines for CRTCs and AMFT blocks
  drm/radeon: print a message if ATPX dGPU power control is missing
  Revert "drm/radeon: disable runtime pm on PX laptops without dGPU power control"
  drm/amdgpu/acp: fix resume on CZ systems with AZ audio
  drm/radeon: add a quirk for a XFX R9 270X
  drm/radeon: print pci revision as well as pci ids on driver load
  drm/amdgpu: when suspending, if uvd/vce was running. need to cancel delay work.
  drm/radeon: fix initial connector audio value

Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: stable@vger.kernel.org
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

transform feedback fix.

* 'linux-4.6' of git://github.com/skeggsb/linux:
  drm/nouveau/gr/gf100: select a stream master to fixup tfb offset queries

Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: stable@vger.kernel.org

Was previously always hardcoded to 0.
Signed-off-by: Sonny Jiang <sonny.jiang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Allowing userptr bo which are basicly a list of page from some vma
(so either anonymous page or file backed page) would lead to serious
corruption of kernel structures and counters (because we overwrite
the page->mapping field when mapping buffer).

This will already block if the buffer was populated before anyone does
try to mmap it because then TTM_PAGE_FLAG_SG would be set in in the
ttm_tt flags. But that flag is check before ttm_tt_populate in the ttm
vm fault handler.

So to be safe just add a check to verify_access() callback.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Jérôme Glisse <jglisse@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Allowing userptr bo which are basicly a list of page from some vma
(so either anonymous page or file backed page) would lead to serious
corruption of kernel structures and counters (because we overwrite
the page->mapping field when mapping buffer).

This will already block if the buffer was populated before anyone does
try to mmap it because then TTM_PAGE_FLAG_SG would be set in in the
ttm_tt flags. But that flag is check before ttm_tt_populate in the ttm
vm fault handler.

So to be safe just add a check to verify_access() callback.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Jérôme Glisse <jglisse@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>