- 06 Feb, 2008 37 commits
-
-
Robert Hancock authored
This fixes some problems with ATAPI devices on nForce4 controllers in ADMA mode on systems with memory located above 4GB. We need to delay setting the 64-bit DMA mask until the PRD table and padding buffer are allocated so that they don't get allocated above 4GB and break legacy mode (which is needed for ATAPI devices). Also, if either port is in ATAPI mode we need to set the DMA mask for the PCI device to 32-bit to ensure that the IOMMU code properly bounces requests above 4GB, as it appears setting the bounce limit does not guarantee that we will not try to map requests above this point. Reported to fix https://bugzilla.redhat.com/show_bug.cgi?id=351451Signed-off-by:
Robert Hancock <hancockr@shaw.ca> Signed-off-by:
Jeff Garzik <jeff@garzik.org>
-
Andrew Morton authored
mips: drivers/ata/sata_mv.c: In function `mv_port_free_dma_mem': drivers/ata/sata_mv.c:1080: error: implicit declaration of function `dma_pool_free' Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
James Bottomley authored
qc->n_iter was used for libata's own sg walking before sg chaining replaced it. During conversion, the field and its usage in sata_fsl were left behind. Kill the filed and update sata_fsl. tj: This was part of James's libata-use-block-layer-padding patch. Separated out by me. Signed-off-by:James Bottomley <James.Bottomley@HansenPartnership.com> Signed-off-by:
Tejun Heo <htejun@gmail.com> Cc: Li Yang <leoli@freescale.com> Signed-off-by:
-
Tejun Heo authored
AHCI uses CAP.NP to indicate the number of ports and PI to tell which ports are enabled. The only requirement is that the number of ports indicated by CAP.NP should equal or be higher than the number of enabled ports in PI. CAP.NP and PI carry duplicate information and there have been some interesting cases. Some early AHCI controllers didn't set PI at all and just implement from port 0 to CAP.NP. An ICH8 board which wired four out of six available ports had 3 (4 ports) for CAP.NP and 0x33 for PI. While ESB2 has less bits set in PI than the value in CAP.NP. Till now, ahci driver assumed that PI is invalid if it doesn't match CAP.NP exactly. This violates AHCI standard and the driver ends up accessing unmimplemented ports on ESB2. This patch updates CAP.NP and PI handling such that PI can have less number of bits set than indicated in CAP.NP and the highest port is determined as the maximum port of what CAP.NP and PI indicate. Signed-off-by:
-
Saeed Bishara authored
Marvell's Orion SoC includes SATA controllers based on Marvell's PCI-to-SATA 88SX controllers. This patch extends the libATA sata_mv driver to support those controllers. [edited to use linux/ata_platform.h -jg] Signed-off-by:
Saeed Bishara <saeed@marvell.com> Signed-off-by:
Jeff Garzik <jgarzik@redhat.com>
-
Jeff Garzik authored
Signed-off-by: -
git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6Linus Torvalds authored
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (29 commits) ide-tape: bump minor driver version ide-tape: cleanup the remaining codestyle issues ide-tape: fix syntax error in idetape_identify_device() ide-tape: remove leftover OnStream support warning ide-tape: collect module-related macro calls at the end ide-tape: include proper headers ide-tape: remove unused "length" arg from idetape_create_read_buffer_cmd() ide-tape: remove struct idetape_id_gcw ide-tape: cleanup and fix comments ide-tape: shorten some function names ide-tape: remove idetape_increase_max_pipeline_stages() ide-tape: struct idetape_tape_t: shorten member names v2 ide-tape: struct idetape_tape_t: remove unused members ide-tape: remove typedef idetape_chrdev_direction_t ide-tape: simplify code branching in the interrupt handler ide-tape: remove unreachable code chunk ide-tape: remove struct idetape_read_position_result_t ide-tape: refactor the debug logging facility ide: add ide_read_error() inline helper ide: add ide_read_[alt]status() inline helpers ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/willy/miscLinus Torvalds authored
* 'dmapool' of git://git.kernel.org/pub/scm/linux/kernel/git/willy/misc: pool: Improve memory usage for devices which can't cross boundaries Change dmapool free block management dmapool: Tidy up includes and add comments dmapool: Validate parameters to dma_pool_create Avoid taking waitqueue lock in dmapool dmapool: Fix style problems Move dmapool.c to mm/ directory
-
Borislav Petkov authored
Signed-off-by:
Borislav Petkov <petkovbb@gmail.com> Signed-off-by:
Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
Borislav Petkov authored
... thus decreasing checkpatch.pl errors to 0. Bart: - remove needless function prototypes while at it - remove needless parentheses while at it - add missing KERN_ level to ide_tape_probe() - other minor fixups Signed-off-by:
-
Borislav Petkov authored
Spotted by Sergei Shtylyov. CC: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by:
-
Borislav Petkov authored
Signed-off-by:
-
Borislav Petkov authored
Signed-off-by:
-
Borislav Petkov authored
Signed-off-by:
-
Borislav Petkov authored
Signed-off-by:
-
Borislav Petkov authored
Signed-off-by:
-
Borislav Petkov authored
Also, remove redundant ones and cleanup whitespace. Bart: - minor fixups Signed-off-by:
-
Borislav Petkov authored
Signed-off-by:
-
Borislav Petkov authored
This function was being used only at one place so fold it in there. Signed-off-by:
-
Borislav Petkov authored
Shorten some member names not too aggressively since this driver might be gone anyway soon. Bart: - minor fixes Signed-off-by:
-
Borislav Petkov authored
- last_frame_position: only being written to once - firmware_revision, product_id, vendor_id: used once, remove from struct idetape_tape_t and deal with them locally - firmware_revision_num: only written to once - tape_still_time_begin: completely unused - tape_still_time: never written to; remove corresponding code chunk - uncontrolled_last_pipeline_head: only once written to - blocks_in_buffer: only written to Signed-off-by:
-
Borislav Petkov authored
.. and replace it with plain enums. Signed-off-by:
-
Borislav Petkov authored
... by adding a new typedef function pointer idetape_io_buf in order to call the proper buffer i/o handler depending on the data direction. Bart: - move idetape_io_buf before idetape_pc_intr() comment Signed-off-by:
-
Borislav Petkov authored
tape->speed_control is set to 1 in idetape_setup(), but, in calculate_speeds() its value is tested for being 0, 1, or 2. Remove the if-branches where tape->speed_control != 1 since they are never executed. Also, rename calculate_speeds() by adding driver's prefix as is with the other function names. Signed-off-by:
-
Borislav Petkov authored
There should be no functional changes resulting from this patch. Bart: - remove needless "!!" Signed-off-by:
-
Borislav Petkov authored
Teach the debug logging macro to differentiate between log levels based on the type of debug level enabled specifically instead of a threshold-based one. Thus, convert tape->debug_level to a bitmask that is written to over /proc. Also, - cleanup and simplify the debug macro thus removing a lot of code lines, - get rid of unused debug levels, - adjust the loglevel at several places where it was simply missing (e.g. idetape_chrdev_open()) - move the tape ptr initialization up in idetape_chrdev_open() so that we can use it in the debug_log macro earlier in the function. Signed-off-by:
-
Bartlomiej Zolnierkiewicz authored
Acked-by:
Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by:
-
Bartlomiej Zolnierkiewicz authored
Acked-by:
-
Bartlomiej Zolnierkiewicz authored
ide-cris.c: * Add cris_setup_ports() helper and use it instead of ide_setup_ports() (fixes random value being set in ->io_ports[IDE_IRQ_OFFSET]). buddha.c: * Add buddha_setup_ports() helper and use it instead of ide_setup_ports(). falconide.c: * Add falconide_setup_ports() helper and use it instead of ide_setup_ports(), also fix return value of falconide_init() while at it. gayle.c: * Add gayle_setup_ports() helper and use it instead of ide_setup_ports(). macide.c: * Add macide_setup_ports() helper and use it instead of ide_setup_ports() (fixes incorrect value being set in ->io_ports[IDE_IRQ_OFFSET]). q40ide.c: * Fix q40_ide_setup_ports() comments. ide.c: * Remove no longer needed ide_setup_ports(). Cc: Mikael Starvik <starvik@axis.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: -
Bartlomiej Zolnierkiewicz authored
Same BUG_ON() is present inside ide_set_handler(). Signed-off-by: -
Bartlomiej Zolnierkiewicz authored
* Remove write-only ->sata_misc[] from ide_hwif_t. * Remove no longer used SATA_{MISC,PHY,IEN}_OFFSET defines. Acked-by: -
Bartlomiej Zolnierkiewicz authored
* Replace incorrect CONFIG_BLK_DEV_IDE #ifdef in check_media_bay() by CONFIG_MAC_FLOPPY one. * Replace incorrect CONFIG_BLK_DEV_IDE #ifdef-s by CONFIG_BLK_DEV_IDE_PMAC ones. * check_media_bay() is used only by drivers/block/swim3.c so make this function available only if CONFIG_MAC_FLOPPY is defined. * check_media_bay_by_base() and media_bay_set_ide_infos() are used only by drivers/ide/ppc/pmac.c so so make these functions available only if CONFIG_MAC_FLOPPY is defined. v2: * Remove ifdefs from function prototypes. (Andrew Morton) Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: -
Denis Cheng authored
with module_param macro, the __setup code can be killed now: const __setup("all-generic-ide", ide_generic_all_on); and the module name "generic.ko" is not descriptive to its functionality, can be changed in Makefile, the "ide-pci-generic.ko" is better. the ide-pci-generic.all-generic-ide parameter also documented in Documentation/kernel-parameters.txt Signed-off-by:Denis Cheng <crquan@gmail.com> Cc: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by:
-
Andrew Morton authored
drivers/ide/legacy/hd.c: In function 'hd_request': drivers/ide/legacy/hd.c:424: warning: 'stat' may be used uninitialized in this function gcc is being stupid. Signed-off-by:
-
Andrew Morton authored
drivers/ide/ide-acpi.c: In function 'ide_acpi_init': drivers/ide/ide-acpi.c:175: warning: 'dev_handle' may be used uninitialized in this function Signed-off-by:
-
Anton Salnikov authored
This is Palmchip BK3710 IDE controller support. The IDE controller logic supports PIO, MultiWord-DMA and Ultra-DMA modes. Supports interface to Compact Flash (CF) configured in True-IDE mode. Bart: - remove dead code - fix ide_hwif_setup_dma() build problem Signed-off-by:
Anton Salnikov <asalnikov@ru.mvista.com> Reviewed-by:
Alan Cox <alan@lxorguk.ukuu.org.uk> Reviewed-by:
-
Bartlomiej Zolnierkiewicz authored
On Tuesday 05 February 2008, Linus Torvalds wrote: > > On Sat, 2 Feb 2008, Bartlomiej Zolnierkiewicz wrote: > > > > * next part of IDE probing code re-organization saga > > (that would be me) > > This seems to cause very irritating and bogus messages for me: > > Probing IDE interface ide0... > Probing IDE interface ide1... > ide2: I/O resource 0x0-0x7 not free. > ide2: ports already in use, skipping probe > ide3: I/O resource 0x0-0x7 not free. > ide3: ports already in use, skipping probe > ide4: I/O resource 0x0-0x7 not free. > ide4: ports already in use, skipping probe > ide5: I/O resource 0x0-0x7 not free. > ide5: ports already in use, skipping probe > ide6: I/O resource 0x0-0x7 not free. > ide6: ports already in use, skipping probe > ide7: I/O resource 0x0-0x7 not free. > ide7: ports already in use, skipping probe > ide8: I/O resource 0x0-0x7 not free. > ide8: ports already in use, skipping probe > ide9: I/O resource 0x0-0x7 not free. > ide9: ports already in use, skipping probe > > and that's just totally bogus. It shouldn't even request that region, > since it's not been allocated! The commit 139ddfca ("ide: move handling of I/O resources out of ide_probe_port()") changed the ordering of hwif->noprobe check vs ide_hwif_request_regions() call (so that we now reserve I/O regions before checking for hwif->noprobe). However ide-generic host driver depended on hwif->noprobe to be set for skipping probing of empty ide_hwifs[] slots. Fix it by passing only indexes of non-empty slots to ide_device_add_all() from ide_generic_init(). Signed-off-by:
-
- 05 Feb, 2008 3 commits
-
-
Andrew Morton authored
smbfs is a bit buggy and has no maintainer. Change it to shout at the user on the first five mount attempts - tell them to switch to CIFS. Come December we'll mark it BROKEN and see what happens. [olecom@flower.upol.cz: documentation update] Cc: Urban Widmark <urban@teststation.com> Acked-by:
Steven French <sfrench@us.ibm.com> Signed-off-by:
Oleg Verych <olecom@flower.upol.cz> Cc: Jeff Layton <jlayton@redhat.com> Cc: Adrian Bunk <bunk@kernel.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
Andrew Morton authored
Cc: David Howells <dhowells@redhat.com> Cc: Hirokazu Takata <takata@linux-m32r.org> Cc: Paul Mundt <lethal@linux-sh.org> Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp> Cc: Richard Curnow <rc@rc0.org.uk> Cc: Davide Libenzi <davidel@xmailserver.org> Cc: Michael Kerrisk <mtk-manpages@gmx.net> Signed-off-by:
-
Haavard Skinnemoen authored
Hmm. Someone removed the timerfd() syscall... Signed-off-by:
-
