Andiry's xHCI bus suspend patch introduced the possibly of a host
controller replaying old commands on the command ring, if the host
successfully restores the registers after a resume.

After a resume from suspend, the xHCI driver must restore the registers,
including the command ring pointer.  I had suggested that Andiry set the
command ring pointer to the current command ring dequeue pointer, so that
the driver wouldn't have to zero the command ring.

Unfortunately, setting the command ring pointer to the current dequeue
pointer won't work because the register assumes the pointer is 64-byte
aligned, and TRBs on the command ring are 16-byte aligned.  The lower
seven bits will always be masked off, leading to the written pointer being
up to 3 TRBs behind the intended pointer.

Here's a log excerpt.  On init, the xHCI driver places a vendor-specific
command on the command ring:

[  215.750958] xhci_hcd 0000:01:00.0: Vendor specific event TRB type = 48
[  215.750960] xhci_hcd 0000:01:00.0: NEC firmware version 30.25
[  215.750962] xhci_hcd 0000:01:00.0: Command ring deq = 0x3781e010 (DMA)

When we resume, the command ring dequeue pointer to be written should have
been 0x3781e010.  Instead, it's 0x3781e000:

[  235.557846] xhci_hcd 0000:01:00.0: // Setting command ring address to 0x3781e001
[  235.557848] xhci_hcd 0000:01:00.0: `MEM_WRITE_DWORD(3'b000, 64'hffffc900100bc038, 64'h3781e001, 4'hf);
[  235.557850] xhci_hcd 0000:01:00.0: `MEM_WRITE_DWORD(3'b000, 32'hffffc900100bc020, 32'h204, 4'hf);
[  235.557866] usb usb9: root hub lost power or was reset

(I can't see the results of this bug because the xHCI restore always fails
on this box, and the xHCI driver re-allocates everything.)

The fix is to zero the command ring and put the software and hardware
enqueue and dequeue pointer back to the beginning of the ring.  We do this
before the system suspends, to be paranoid and prevent the BIOS from
starting the host without clearing the command ring pointer, which might
cause the host to muck with stale memory.  (The pointer isn't required to
be in the suspend power well, but it could be.)  The command ring pointer
is set again after the host resumes.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Andiry Xu <andiry.xu@amd.com>

USB2.0 spec 9.6.6 says: For all endpoints, bit 10..0 specify the maximum
packet size(in bytes).

So the wMaxPacketSize mask should be 0x7ff rather than 0x3ff.

This patch should be queued for the stable tree.  The bug in
xhci_endpoint_init() was present as far back as 2.6.31, and the bug in
xhci_get_max_esit_payload() was present when the function was introduced
in 2.6.34.
Reported-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org

Jiri Slaby reports spinlock is held while calling kmalloc(GFP_KERNEL)
and request_irq() in xhci_resume().

Release the spinlock when setup interrupt.
Reported-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>

If the xHCI host controller shares an interrupt line with another device,
the xHCI driver needs to check if the interrupt was generated by its
hardware.  Unfortunately, the user will see a ton of "Spurious interrupt."
lines if the other hardware interrupts often.  Lawrence found his dmesg
output cluttered with this output when the xHCI host shared an interrupt
with his i915 hardware.

Remove the warning, as sharing an interrupt is a normal thing.

This should be applied to the 2.6.36 stable tree.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Lawrence Rust <lvr@softsystem.co.uk>
Cc: stable@kernel.org

This reverts commit ef821ae7.

The correct thing to do is to drop the spinlock, not change
the GFP flag here.

Thanks to Sarah for pointing out I shouldn't have taken this patch in
the first place.

Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: David Sterba <dsterba@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

platfrom -> platform

Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Reviewed-by: Jesper Juhl <jj@chaosbits.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Crashing on a null pointer deref is never a nice thing to do. It seems
to me that it's better to simply return UWB_RSV_ALLOC_NOT_FOUND if
kzalloc() fails in uwb_rsv_find_best_allocation().
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Structure usbdevfs_connectinfo is copied to userland with padding byted
after "slow" field uninitialized.  It leads to leaking of contents of
kernel stack memory.
Signed-off-by: Vasiliy Kulikov <segooon@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Structure iowarrior_info is copied to userland with padding byted
between "serial" and "revision" fields uninitialized.  It leads to
leaking of contents of kernel stack memory.
Signed-off-by: Vasiliy Kulikov <segooon@gmail.com>
Cc: stable <stable@kernel.org>
Acked-by: Kees Cook <kees.cook@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Structure sisusb_info is copied to userland with "sisusb_reserved" field
uninitialized.  It leads to leaking of contents of kernel stack memory.
Signed-off-by: Vasiliy Kulikov <segooon@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

OK, the USB gadget serial driver actually has a couple of problems.  On
gs_open(), it always allocates and queues an additional QUEUE_SIZE (16)
worth of requests, so with a loop like this:

    i=1 ; while echo $i > /dev/ttyGS0 ; do let i++ ; done

eventually we run into OOM (Out of Memory).

Technically, it is not a leak as everything gets freed up when the USB
connection is broken, but not on gs_close().

With a USB device/gadget controller driver that has limited resources
(e.g., Marvell has a this MAX_XDS_FOR_TR_CALLS of 64 for transmit and
receive), so even after 4

    stty -F /dev/ttyGS0

we cannot transmit anymore.  We can still receive (not necessarily
reliably) as now we have 16 * 4 = 64 descriptors/buffers ready, but the
device is otherwise not usable.
Signed-off-by: Jim Sung <jsung@syncadence.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

When huawei datacard with PID 0x14AC is insterted into Linux system, the
present kernel will load the "option" driver to all the interfaces. But
actually, some interfaces run as other function and do not need "option"
driver.

In this path, we modify the id_tables, when the PID is 0x14ac ,VID is
0x12d1, Only when the interface's Class is 0xff,Subclass is 0xff, Pro is
0xff, it does need "option" driver.
Signed-off-by: ma rui <m00150988@huawei.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

coccinelle check scripts/coccinelle/locks/call_kern.cocci found that
in drivers/usb/host/xhci.c an allocation with GFP_KERNEL is done
with locks held:

xhci_resume
  spin_lock_irq(xhci->lock)
    xhci_setup_msix
      kmalloc(GFP_KERNEL)

Change it to GFP_ATOMIC.
Signed-off-by: David Sterba <dsterba@suse.cz>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The commit below cleaned up error handling, in part by introducing a
registered flag bit.  This however was not added to the device
structure leding to build failures:

  commit 319feaab
  Author: Dan Carpenter <error27@gmail.com>
  Date:   Tue Oct 5 18:55:34 2010 +0200

    usb: gadget: goku_udc: Fix error path

Add the missing registered flag bit.
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Acked-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Commit
	65fd4272 (USB: ehci tdi : let's tdi_reset set host mode)

broke the build using ARM's mx51_defconfig:

 	  CC      drivers/usb/host/ehci-hcd.o
 	In file included from drivers/usb/host/ehci-hcd.c:1166:
 	drivers/usb/host/ehci-mxc.c: In function 'ehci_mxc_drv_probe':
 	drivers/usb/host/ehci-mxc.c:192: error: 'ehci' undeclared (first use in this function)
 	drivers/usb/host/ehci-mxc.c:192: error: (Each undeclared identifier is reported only once
 	drivers/usb/host/ehci-mxc.c:192: error: for each function it appears in.)
 	drivers/usb/host/ehci-mxc.c:117: warning: unused variable 'temp'
 	make[3]: *** [drivers/usb/host/ehci-hcd.o] Error 1
 	make[2]: *** [drivers/usb/host/ehci-hcd.o] Error 2
 	make[1]: *** [sub-make] Error 2
 	make: *** [all] Error 2

Fix it together with the warning about the unused variable and use
msleep instead of mdelay as requested by Alan Stern.

Cc: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Nguyen Dinh-R00091 <R00091@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Commit 126512e3 added support for FSL's USB
controller on powerpc. In this commit the Open Firmware code was selected
and compiled unconditionally.

This breaks on ARM systems from FSL which use the same driver (.i.e. the i.MX
series), because ARM don't have OF support (yet). This patch fixes the problem
by only selecting the OF code on systems with Open Firmware support.
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Compile-Tested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

So change the MAINTAINERS file to properly reflect this.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The Inventra DMA engine in version 1.8 and later of the MUSB
controller cannot handle DMA addresses that are not aligned
to a 4 byte boundary. It ends up ignoring the last two bits
programmed in the DMA_ADDR register. This is a deliberate
design change in the controller and is documented in the
programming guide.

Earlier versions of the controller could handle these
accesses just fine.

Fail dma_channel_program if we see an unaligned address when
using the newer controllers, so that the caller can carry out
the transfer using PIO mode.
(Current callers already have this backup path in place).
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Tested-by: Ming Lei <tom.leiming@gmail.com>
Cc: Ajay Kumar Gupta <ajay.gupta@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Add the USB IDs for the Milkymist One FTDI-based JTAG/serial adapter
(http://projects.qi-hardware.com/index.php/p/mmone-jtag-serial-cable/)
to the ftdi_sio driver and disable the first serial channel (used as
JTAG from userspace).
Signed-off-by: Sebastien Bourdeauducq <sebastien@milkymist.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Fix struct field name, prevent kernel-doc warnings.

Warning(include/linux/usb.h:865): No description found for parameter 'unlocked_ioctl'
Warning(include/linux/usb.h:865): Excess struct/union/enum/typedef member 'ioctl' description in 'usb_driver'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
  TTY: move .gitignore from drivers/char/ to drivers/tty/vt/
  TTY: create drivers/tty/vt and move the vt code there
  TTY: create drivers/tty and move the tty core files there

Merge branch 'staging-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-next-2.6

* 'staging-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-next-2.6:
  Staging: ath6kl: remove empty files that mess with 'distclean'
  staging: ath6kl: Fixing the driver to use modified mmc_host structure
  Staging: solo6x10: fix build problem

Merge branch 'rmobile-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6

* 'rmobile-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
  mmc: sh_mmcif: Convert extern inline to static inline.
  ARM: mach-shmobile: Allow GPIO chips to register IRQ mappings.
  ARM: mach-shmobile: fix sh7372 after a recent clock framework rework
  ARM: mach-shmobile: include drivers/sh/Kconfig
  ARM: mach-shmobile: ap4evb: Add HDMI sound support
  ARM: mach-shmobile: clock-sh7372: Add FSIDIV clock support
  ARM: shmobile: remove sh_timer_config clk member

* 'sh-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
  sh: clkfwk: Fix up checkpatch warnings.
  sh: make some needlessly global sh7724 clocks static
  sh: add clk_round_parent() to optimize parent clock rate
  sh: Simplify phys_addr_mask()/PTE_PHYS_MASK for 29/32-bit.
  sh: nommu: Support building without an uncached mapping.
  sh: nommu: use 32-bit phys mode.
  sh: mach-se: Fix up SE7206 no ioport build.
  sh: intc: Update for single IRQ reservation helper.
  sh: clkfwk: Fix up rate rounding error handling.
  sh: mach-se: Rip out superfluous 7751 PIO routines.
  sh: mach-se: Rip out superfluous 770x PIO routines.
  sh: mach-edosk7705: Kill off machtype, consolidate board def.
  sh: mach-edosk7705: update for this century, kill off PIO trapping.
  sh: mach-se: Rip out superfluous 7206 PIO routines.
  sh: mach-systemh: Kill off dead board.
  sh: mach-snapgear: Kill off machtype, consolidate board def.
  sh: mach-snapgear: Rip out superfluous PIO routines.
  sh: mach-microdev: SuperIO-relative ioport mapping.

musb_gadget_queue() checks for '!req->buf' condition twice:
in the second case the code is both duplicated and unreachable
as the first check returns early.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Merge branches 'sh/pio-death', 'sh/nommu', 'sh/clkfwk', 'sh/core' and 'sh/intc-extension' into sh-fixes-for-linus

The clk_round_parent() change introduced various checkpatch warnings,
tidy them up.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

These clocks are currently only used inside one .c file and are not
declared in any headers, therefore having them global is useless.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Sometimes it is possible and reasonable to adjust the parent clock rate to
improve precision of the child clock, e.g., if the child clock has no siblings.
clk_round_parent() is a new addition to the SH clock-framework API, that
implements such an optimization for child clocks with divisors, taking all
integer values in a range.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

These two .h files would get removed from the tree when doing
	make distclean

It turns out they are not needed at all, so just delete them which fixes
people's git trees when doing development.
Reported-by: Andi Kleen <andi@firstfloor.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

While scanning the floopy code due to c093ee4f ("floppy: fix
use-after-free in module load failure path"), I found one more instance
of trying to access disk->queue pointer after doing put_disk() on
gendisk.  For some reason , floppy moule still loads/unloads fine.  The
object is probably still around with right pointer values.

 o There seems to be one more instance of trying to cleanup the request
   queue after we have called put_disk() on associated gendisk.

 o This fix is more out of code inspection.  Even without this fix for
   some reason I am able to load/unload floppy module without any
   issues.

 o Floppy module loads/unloads fine after the fix.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The autogenerated files (consolemap_deftbl.c and defkeymap.c) need to
be ignored by git, so move the .gitignore file that was doing it to the
properly location now that the files have moved as well.

Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Commit 27ae60f8 ("ipw2x00: replace "ieee80211" with "libipw" where
appropriate") changed DRV_NAME to be "libipw", but didn't properly fix
up the places where it was used to specify the name for the /proc/net/
directory.

For backwards compatibility reasons, that directory name remained
"ieee80211", but due to the DRV_NAME change, the error case printouts
and the cleanup functions now used "libipw" instead.  Which made it all
fail badly.

For example, on module unload as reported by Randy:

  WARNING: at fs/proc/generic.c:816 remove_proc_entry+0x156/0x35e()
  name 'libipw'

because it's trying to unregister a /proc directory that obviously
doesn't even exist.

Clean it all up to use DRV_PROCNAME for the actual /proc directory name.
Reported-and-tested-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Pavel Roskin <proski@gnu.org>
Cc: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'kvm-updates/2.6.37' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: PPC: BookE: Load the lower half of MSR
  KVM: PPC: BookE: fix sleep with interrupts disabled
  KVM: PPC: e500: Call kvm_vcpu_uninit() before kvmppc_e500_tlb_uninit().
  PPC: KVM: Book E doesn't have __end_interrupts.
  KVM: x86: Issue smp_call_function_many with preemption disabled
  KVM: x86: fix information leak to userland
  KVM: PPC: fix information leak to userland
  KVM: MMU: fix rmap_remove on non present sptes
  KVM: Write protect memory after slot swap

Commit 48821184 ("floppy: switch to one queue per drive instead of
sharing a queue") introduced a use-after-free.  We do "put_disk()" on
the disk device _before_ we then clean up the queue associated with that
disk.

Move the put_disk() down to avoid dereferencing a free'd data structure.

Cc: Jens Axboe <jaxboe@fusionio.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Reported-and-tested-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit d9ca07a0 ("watchdog: Avoid kernel crash when disabling
watchdog") introduces a section mismatch.

Now that we reference no_watchdog from non-__init code it can no longer
be __initdata.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (41 commits)
  inet_diag: Make sure we actually run the same bytecode we audited.
  netlink: Make nlmsg_find_attr take a const nlmsghdr*.
  fib: fib_result_assign() should not change fib refcounts
  netfilter: ip6_tables: fix information leak to userspace
  cls_cgroup: Fix crash on module unload
  memory corruption in X.25 facilities parsing
  net dst: fix percpu_counter list corruption and poison overwritten
  rds: Remove kfreed tcp conn from list
  rds: Lost locking in loop connection freeing
  de2104x: fix panic on load
  atl1 : fix panic on load
  netxen: remove unused firmware exports
  caif: Remove noisy printout when disconnecting caif socket
  caif: SPI-driver bugfix - incorrect padding.
  caif: Bugfix for socket priority, bindtodev and dbg channel.
  smsc911x: Set Ethernet EEPROM size to supported device's size
  ipv4: netfilter: ip_tables: fix information leak to userland
  ipv4: netfilter: arp_tables: fix information leak to userland
  cxgb4vf: remove call to stop TX queues at load time.
  cxgb4: remove call to stop TX queues at load time.
  ...

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
  firewire: ohci: fix race when reading count in AR descriptor
  firewire: ohci: avoid reallocation of AR buffers
  firewire: ohci: fix race in AR split packet handling
  firewire: ohci: fix buffer overflow in AR split packet handling