Add Nick Child as the maintainer of the IBM Power Virtual Ethernet
Device Driver, replacing Cristobal Forno.
Signed-off-by: Nick Child <nnac123@linux.ibm.com>
Link: https://lore.kernel.org/r/20220803155246.39582-1-nnac123@linux.ibm.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

bnxt_ethtool.h is included twice in bnxt_devlink.c,
remove one of them.

Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=1817Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Link: https://lore.kernel.org/r/20220804003722.54088-1-yang.lee@linux.alibaba.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Florian Westphal says:

====================
netfilter followup fixes for net

Regressions, since 5.19:
Fix crash when packet tracing is enabled via 'meta nftrace set 1' rule.
Also comes with a test case.

Regressions, this cycle:
Fix Kconfig dependency for the flowtable /proc interface, we want this
to be off by default.
====================

Link: https://lore.kernel.org/r/20220804172629.29748-1-fw@strlen.deSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Remove default to 'y', this infrastructure is not fundamental for the
flowtable operational.

Add a missing dependency on CONFIG_NF_FLOW_TABLE.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes: b0381776 ("netfilter: nf_flow_table: count pending offload workqueue tasks")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Enable/disable tracing infrastructure while packets are in-flight.
This triggers KASAN splat after
e34b9ed9 ("netfilter: nf_tables: avoid skb access on nf_stolen").

While at it, reduce script run time as well.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

do not access info->pkt when info->trace is not 1.
nft_traceinfo is not initialized, except when tracing is enabled.

The 'nft_trace_enabled' static key cannot be used for this, we must
always check info->trace first.

Pass nft_pktinfo directly to avoid this.

Fixes: e34b9ed9 ("netfilter: nf_tables: avoid skb access on nf_stolen")
Reported-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Few test cases related to the fix for 924a9bc3:
"net: check if protocol extracted by virtio_net_hdr_set_proto is correct"

Need test for the case when a non-standard packet (GSO without NEEDS_CSUM)
sent to the tap device causes a BUG check in the tap driver.
Signed-off-by: Cezar Bulinaru <cbulinaru@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes a NULL pointer derefence bug triggered from tap driver.
When tap_get_user calls virtio_net_hdr_to_skb the skb->dev is null
(in tap.c skb->dev is set after the call to virtio_net_hdr_to_skb)
virtio_net_hdr_to_skb calls dev_parse_header_protocol which
needs skb->dev field to be valid.

The line that trigers the bug is in dev_parse_header_protocol
(dev is at offset 0x10 from skb and is stored in RAX register)
  if (!dev->header_ops || !dev->header_ops->parse_protocol)
  22e1:   mov    0x10(%rbx),%rax
  22e5:	  mov    0x230(%rax),%rax

Setting skb->dev before the call in tap.c fixes the issue.

BUG: kernel NULL pointer dereference, address: 0000000000000230
RIP: 0010:virtio_net_hdr_to_skb.constprop.0+0x335/0x410 [tap]
Code: c0 0f 85 b7 fd ff ff eb d4 41 39 c6 77 cf 29 c6 48 89 df 44 01 f6 e8 7a 79 83 c1 48 85 c0 0f 85 d9 fd ff ff eb b7 48 8b 43 10 <48> 8b 80 30 02 00 00 48 85 c0 74 55 48 8b 40 28 48 85 c0 74 4c 48
RSP: 0018:ffffc90005c27c38 EFLAGS: 00010246
RAX: 0000000000000000 RBX: ffff888298f25300 RCX: 0000000000000010
RDX: 0000000000000005 RSI: ffffc90005c27cb6 RDI: ffff888298f25300
RBP: ffffc90005c27c80 R08: 00000000ffffffea R09: 00000000000007e8
R10: ffff88858ec77458 R11: 0000000000000000 R12: 0000000000000001
R13: 0000000000000014 R14: ffffc90005c27e08 R15: ffffc90005c27cb6
FS:  0000000000000000(0000) GS:ffff88858ec40000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000230 CR3: 0000000281408006 CR4: 00000000003706e0
Call Trace:
 tap_get_user+0x3f1/0x540 [tap]
 tap_sendmsg+0x56/0x362 [tap]
 ? get_tx_bufs+0xc2/0x1e0 [vhost_net]
 handle_tx_copy+0x114/0x670 [vhost_net]
 handle_tx+0xb0/0xe0 [vhost_net]
 handle_tx_kick+0x15/0x20 [vhost_net]
 vhost_worker+0x7b/0xc0 [vhost]
 ? vhost_vring_call_reset+0x40/0x40 [vhost]
 kthread+0xfa/0x120
 ? kthread_complete_and_exit+0x20/0x20
 ret_from_fork+0x1f/0x30

Fixes: 924a9bc3 ("net: check if protocol extracted by virtio_net_hdr_set_proto is correct")
Signed-off-by: Cezar Bulinaru <cbulinaru@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Mat Martineau says:

====================
mptcp: Fixes for mptcp cleanup/close and a selftest

Patch 1 fixes an issue with leaking subflow sockets if there's a failure
in a CGROUP_INET_SOCK_CREATE eBPF program.

Patch 2 fixes a syzkaller-detected race at MPTCP socket close.

Patch 3 is a fix for one mode of the mptcp_connect.sh selftest.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When the selftest got added, sendfile() on mptcp sockets returned
-EOPNOTSUPP, so running 'mptcp_connect.sh -m sendfile' failed
immediately.

This is no longer the case, but the script fails anyway due to timeout.
Let the receiver know once the sender has sent all data, just like
with '-m mmap' mode.

v2: need to respect cfg_wait too, as pm_userspace.sh relied
on -m sendfile to keep the connection open (Mat Martineau)

Fixes: 048d19d4 ("mptcp: add basic kselftest for mptcp")
Reported-by: Xiumei Mu <xmu@redhat.com>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Dipanjan reported a syzbot splat at close time:

WARNING: CPU: 1 PID: 10818 at net/ipv4/af_inet.c:153
inet_sock_destruct+0x6d0/0x8e0 net/ipv4/af_inet.c:153
Modules linked in: uio_ivshmem(OE) uio(E)
CPU: 1 PID: 10818 Comm: kworker/1:16 Tainted: G           OE
5.19.0-rc6-g2eae0556bb9d #2
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS
1.13.0-1ubuntu1.1 04/01/2014
Workqueue: events mptcp_worker
RIP: 0010:inet_sock_destruct+0x6d0/0x8e0 net/ipv4/af_inet.c:153
Code: 21 02 00 00 41 8b 9c 24 28 02 00 00 e9 07 ff ff ff e8 34 4d 91
f9 89 ee 4c 89 e7 e8 4a 47 60 ff e9 a6 fc ff ff e8 20 4d 91 f9 <0f> 0b
e9 84 fe ff ff e8 14 4d 91 f9 0f 0b e9 d4 fd ff ff e8 08 4d
RSP: 0018:ffffc9001b35fa78 EFLAGS: 00010246
RAX: 0000000000000000 RBX: 00000000002879d0 RCX: ffff8881326f3b00
RDX: 0000000000000000 RSI: ffff8881326f3b00 RDI: 0000000000000002
RBP: ffff888179662674 R08: ffffffff87e983a0 R09: 0000000000000000
R10: 0000000000000005 R11: 00000000000004ea R12: ffff888179662400
R13: ffff888179662428 R14: 0000000000000001 R15: ffff88817e38e258
FS:  0000000000000000(0000) GS:ffff8881f5f00000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000020007bc0 CR3: 0000000179592000 CR4: 0000000000150ee0
Call Trace:
 <TASK>
 __sk_destruct+0x4f/0x8e0 net/core/sock.c:2067
 sk_destruct+0xbd/0xe0 net/core/sock.c:2112
 __sk_free+0xef/0x3d0 net/core/sock.c:2123
 sk_free+0x78/0xa0 net/core/sock.c:2134
 sock_put include/net/sock.h:1927 [inline]
 __mptcp_close_ssk+0x50f/0x780 net/mptcp/protocol.c:2351
 __mptcp_destroy_sock+0x332/0x760 net/mptcp/protocol.c:2828
 mptcp_worker+0x5d2/0xc90 net/mptcp/protocol.c:2586
 process_one_work+0x9cc/0x1650 kernel/workqueue.c:2289
 worker_thread+0x623/0x1070 kernel/workqueue.c:2436
 kthread+0x2e9/0x3a0 kernel/kthread.c:376
 ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:302
 </TASK>

The root cause of the problem is that an mptcp-level (re)transmit can
race with mptcp_close() and the packet scheduler checks the subflow
state before acquiring the socket lock: we can try to (re)transmit on
an already closed ssk.

Fix the issue checking again the subflow socket status under the
subflow socket lock protection. Additionally add the missing check
for the fallback-to-tcp case.

Fixes: d5f49190 ("mptcp: allow picking different xmit subflows")
Reported-by: Dipanjan Das <mail.dipanjan.das@gmail.com>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the mptcp socket creation fails due to a CGROUP_INET_SOCK_CREATE
eBPF program, the MPTCP protocol ends-up leaking all the subflows:
the related cleanup happens in __mptcp_destroy_sock() that is not
invoked in such code path.

Address the issue moving the subflow sockets cleanup in the
mptcp_destroy_common() helper, which is invoked in every msk cleanup
path.

Additionally get rid of the intermediate list_splice_init step, which
is an unneeded relic from the past.

The issue is present since before the reported root cause commit, but
any attempt to backport the fix before that hash will require a complete
rewrite.

Fixes: e16163b6 ("mptcp: refactor shutdown and close")
Reported-by: Nguyen Dinh Phi <phind.uet@gmail.com>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Co-developed-by: Nguyen Dinh Phi <phind.uet@gmail.com>
Signed-off-by: Nguyen Dinh Phi <phind.uet@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The port flag isn't set to `NFP_PORT_CHANGED` when using
`ethtool -m DEVNAME` before, so the port state (e.g. interface)
cannot be updated. Therefore, it caused that `ethtool -m DEVNAME`
sometimes cannot read the correct information.

E.g. `ethtool -m DEVNAME` cannot work when load driver before plug
in optical module, as the port interface is still NONE without port
update.

Now update the port state before sending info to NIC to ensure that
port interface is correct (latest state).

Fixes: 61f7c6f4 ("nfp: implement ethtool get module EEPROM")
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Yu Xiao <yu.xiao@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20220802093355.69065-1-simon.horman@corigine.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Calling mdio_bus_phy_resume() with neither the PHY state machine set to
PHY_HALTED nor phydev->mac_managed_pm set to true is a good indication
that we can produce a race condition looking like this:

CPU0						CPU1
bcmgenet_resume
 -> phy_resume
   -> phy_init_hw
 -> phy_start
   -> phy_resume
                                                phy_start_aneg()
mdio_bus_phy_resume
 -> phy_resume
    -> phy_write(..., BMCR_RESET)
     -> usleep()                                  -> phy_read()

with the phy_resume() function triggering a PHY behavior that might have
to be worked around with (see bf8bfc43 ("net: phy: broadcom: Fix
brcm_fet_config_init()") for instance) that ultimately leads to an error
reading from the PHY.

Fixes: fba863b8 ("net: phy: make PHY PM ops a no-op if MAC driver manages PHY PM")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220801233403.258871-1-f.fainelli@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Vladimir Oltean says:

====================
Make DSA work with bonding's ARP monitor

Since commit 2b86cb82 ("net: dsa: declare lockless TX feature for
slave ports") in v5.7, DSA breaks the ARP monitoring logic from the
bonding driver, fact which was pointed out by Brian Hutchinson who uses
a linux-5.10.y stable kernel.

Initially I got lured by other similar hacks introduced for other
NETIF_F_LLTX drivers, which, inspired by the bonding documentation,
update the trans_start of their TX queues by hand.

However Jakub pointed out that this simply isn't a proper solution, and
after coming to think more about it, I agree, and it doesn't work
properly with DSA nor is it maintainable for the future changes I plan
for it (multiple DSA masters in a LAG).

I've tested these changes using a DSA-based setup and a veth-based
setup, using the active-backup mode and ARP monitoring, with and without
arp_validate.

Link to v1:
https://patchwork.kernel.org/project/netdevbpf/patch/20220715232641.952532-1-vladimir.oltean@nxp.com/

Link to v2:
https://patchwork.kernel.org/project/netdevbpf/patch/20220727152000.3616086-1-vladimir.oltean@nxp.com/
====================

Link: https://lore.kernel.org/r/20220731124108.2810233-1-vladimir.oltean@nxp.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

ARP monitoring no longer depends on dev->last_rx or dev_trans_start(),
so delete this information.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

This reverts commit e66e257a. The veth
driver no longer needs these hacks which are slightly detrimential to
the fast path performance, because the bonding driver is keeping track
of TX times of ARP and NS probes by itself, which it should.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Now that the bonding driver keeps track of the last TX time of ARP and
NS probes, we effectively revert the following commits:

32d3e51a ("net_sched: use macvlan real dev trans_start in dev_trans_start()")
07ce76aa ("net_sched: make dev_trans_start return vlan's real dev trans_start")

Note that the approach of continuing to hack at this function would not
get us very far, hence the desire to take a different approach. DSA is
also a virtual device that uses NETIF_F_LLTX, but there, many uppers
share the same lower (DSA master, i.e. the physical host port of a
switch). By making dev_trans_start() on a DSA interface return the
dev_trans_start() of the master, we effectively assume that all other
DSA interfaces are silent, otherwise this corrupts the validity of the
probe timestamp data from the bonding driver's perspective.

Furthermore, the hacks didn't take into consideration the fact that the
lower interface of @dev may not have been physical either. For example,
VLAN over VLAN, or DSA with 2 masters in a LAG.

And even furthermore, there are NETIF_F_LLTX devices which are not
stacked, like veth. The hack here would not work with those, because it
would not have to provide the bonding driver something to chew at all.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The bonding driver piggybacks on time stamps kept by the network stack
for the purpose of the netdev TX watchdog, and this is problematic
because it does not work with NETIF_F_LLTX devices.

It is hard to say why the driver looks at dev_trans_start() of the
slave->dev, considering that this is updated even by non-ARP/NS probes
sent by us, and even by traffic not sent by us at all (for example PTP
on physical slave devices). ARP monitoring in active-backup mode appears
to still work even if we track only the last TX time of actual ARP
probes.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Pull networking changes from Paolo Abeni:
 "Core:

   - Refactor the forward memory allocation to better cope with memory
     pressure with many open sockets, moving from a per socket cache to
     a per-CPU one

   - Replace rwlocks with RCU for better fairness in ping, raw sockets
     and IP multicast router.

   - Network-side support for IO uring zero-copy send.

   - A few skb drop reason improvements, including codegen the source
     file with string mapping instead of using macro magic.

   - Rename reference tracking helpers to a more consistent netdev_*
     schema.

   - Adapt u64_stats_t type to address load/store tearing issues.

   - Refine debug helper usage to reduce the log noise caused by bots.

  BPF:

   - Improve socket map performance, avoiding skb cloning on read
     operation.

   - Add support for 64 bits enum, to match types exposed by kernel.

   - Introduce support for sleepable uprobes program.

   - Introduce support for enum textual representation in libbpf.

   - New helpers to implement synproxy with eBPF/XDP.

   - Improve loop performances, inlining indirect calls when possible.

   - Removed all the deprecated libbpf APIs.

   - Implement new eBPF-based LSM flavor.

   - Add type match support, which allow accurate queries to the eBPF
     used types.

   - A few TCP congetsion control framework usability improvements.

   - Add new infrastructure to manipulate CT entries via eBPF programs.

   - Allow for livepatch (KLP) and BPF trampolines to attach to the same
     kernel function.

  Protocols:

   - Introduce per network namespace lookup tables for unix sockets,
     increasing scalability and reducing contention.

   - Preparation work for Wi-Fi 7 Multi-Link Operation (MLO) support.

   - Add support to forciby close TIME_WAIT TCP sockets via user-space
     tools.

   - Significant performance improvement for the TLS 1.3 receive path,
     both for zero-copy and not-zero-copy.

   - Support for changing the initial MTPCP subflow priority/backup
     status

   - Introduce virtually contingus buffers for sockets over RDMA, to
     cope better with memory pressure.

   - Extend CAN ethtool support with timestamping capabilities

   - Refactor CAN build infrastructure to allow building only the needed
     features.

  Driver API:

   - Remove devlink mutex to allow parallel commands on multiple links.

   - Add support for pause stats in distributed switch.

   - Implement devlink helpers to query and flash line cards.

   - New helper for phy mode to register conversion.

  New hardware / drivers:

   - Ethernet DSA driver for the rockchip mt7531 on BPI-R2 Pro.

   - Ethernet DSA driver for the Renesas RZ/N1 A5PSW switch.

   - Ethernet DSA driver for the Microchip LAN937x switch.

   - Ethernet PHY driver for the Aquantia AQR113C EPHY.

   - CAN driver for the OBD-II ELM327 interface.

   - CAN driver for RZ/N1 SJA1000 CAN controller.

   - Bluetooth: Infineon CYW55572 Wi-Fi plus Bluetooth combo device.

  Drivers:

   - Intel Ethernet NICs:
      - i40e: add support for vlan pruning
      - i40e: add support for XDP framented packets
      - ice: improved vlan offload support
      - ice: add support for PPPoE offload

   - Mellanox Ethernet (mlx5)
      - refactor packet steering offload for performance and scalability
      - extend support for TC offload
      - refactor devlink code to clean-up the locking schema
      - support stacked vlans for bridge offloads
      - use TLS objects pool to improve connection rate

   - Netronome Ethernet NICs (nfp):
      - extend support for IPv6 fields mangling offload
      - add support for vepa mode in HW bridge
      - better support for virtio data path acceleration (VDPA)
      - enable TSO by default

   - Microsoft vNIC driver (mana)
      - add support for XDP redirect

   - Others Ethernet drivers:
      - bonding: add per-port priority support
      - microchip lan743x: extend phy support
      - Fungible funeth: support UDP segmentation offload and XDP xmit
      - Solarflare EF100: add support for virtual function representors
      - MediaTek SoC: add XDP support

   - Mellanox Ethernet/IB switch (mlxsw):
      - dropped support for unreleased H/W (XM router).
      - improved stats accuracy
      - unified bridge model coversion improving scalability (parts 1-6)
      - support for PTP in Spectrum-2 asics

   - Broadcom PHYs
      - add PTP support for BCM54210E
      - add support for the BCM53128 internal PHY

   - Marvell Ethernet switches (prestera):
      - implement support for multicast forwarding offload

   - Embedded Ethernet switches:
      - refactor OcteonTx MAC filter for better scalability
      - improve TC H/W offload for the Felix driver
      - refactor the Microchip ksz8 and ksz9477 drivers to share the
        probe code (parts 1, 2), add support for phylink mac
        configuration

   - Other WiFi:
      - Microchip wilc1000: diable WEP support and enable WPA3
      - Atheros ath10k: encapsulation offload support

  Old code removal:

   - Neterion vxge ethernet driver: this is untouched since more than 10 years"

* tag 'net-next-6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1890 commits)
  doc: sfp-phylink: Fix a broken reference
  wireguard: selftests: support UML
  wireguard: allowedips: don't corrupt stack when detecting overflow
  wireguard: selftests: update config fragments
  wireguard: ratelimiter: use hrtimer in selftest
  net/mlx5e: xsk: Discard unaligned XSK frames on striding RQ
  net: usb: ax88179_178a: Bind only to vendor-specific interface
  selftests: net: fix IOAM test skip return code
  net: usb: make USB_RTL8153_ECM non user configurable
  net: marvell: prestera: remove reduntant code
  octeontx2-pf: Reduce minimum mtu size to 60
  net: devlink: Fix missing mutex_unlock() call
  net/tls: Remove redundant workqueue flush before destroy
  net: txgbe: Fix an error handling path in txgbe_probe()
  net: dsa: Fix spelling mistakes and cleanup code
  Documentation: devlink: add add devlink-selftests to the table of contents
  dccp: put dccp_qpolicy_full() and dccp_qpolicy_push() in the same lock
  net: ionic: fix error check for vlan flags in ionic_set_nic_features()
  net: ice: fix error NETIF_F_HW_VLAN_CTAG_FILTER check in ice_vsi_sync_fltr()
  nfp: flower: add support for tunnel offload without key ID
  ...

Pull ATA updates from Damien Le Moal:

 - Some code refactoring for the pata_hpt37x and pata_hpt3x2n drivers,
   from Sergei.

 - Several patches to cleanup in libata-core, libata-scsi and libata-eh
   code: fixes arguments and variables types, change some functions
   declaration to static and fix for a typo in a comment. From Sergey
   and Xiang.

 - Fix a compilation warning in the pata_macio driver, from me.

 - A fix for the expected number of resources in the sata_mv driver fix,
   from Andrew.

* tag 'ata-5.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata:
  ata: sata_mv: Fixes expected number of resources now IRQs are gone
  ata: libata-scsi: fix result type of ata_ioc32()
  ata: pata_macio: Fix compilation warning
  ata: libata-eh: fix sloppy result type of ata_internal_cmd_timeout()
  ata: libata-core: fix sloppy parameter type in ata_exec_internal[_sg]()
  ata: make ata_port::fastdrain_cnt *unsigned int*
  ata: libata-eh: fix sloppy result type of ata_eh_nr_in_flight()
  ata: libata-core: make ata_exec_internal_sg() *static*
  ata: make transfer mode masks *unsigned int*
  ata: libata-core: get rid of *else* branches in ata_id_n_sectors()
  ata: libata-core: fix sloppy typing in ata_id_n_sectors()
  ata: pata_hpt3x2n: pass base DPLL frequency to hpt3x2n_pci_clock()
  ata: pata_hpt37x: merge hpt374_read_freq() to hpt37x_pci_clock()
  ata: pata_hpt37x: factor out hpt37x_pci_clock()
  ata: pata_hpt37x: move claculating PCI clock from hpt37x_clock_slot()
  ata: libata: Fix syntax errors in comments

Pull zonefs update from Damien Le Moal:
 "A single change for this cycle to simplify handling of the memory page
  used as super block buffer during mount (from Fabio)"

* tag 'zonefs-5.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/zonefs:
  zonefs: Call page_address() on page acquired with GFP_KERNEL flag

Pull iomap updates from Darrick Wong:
 "The most notable change in this first batch is that we no longer
  schedule pages beyond i_size for writeback, preferring instead to let
  truncate deal with those pages.

  Next week, there may be a second pull request to remove
  iomap_writepage from the other two filesystems (gfs2/zonefs) that use
  iomap for buffered IO. This follows in the same vein as the recent
  removal of writepage from XFS, since it hasn't been triggered in a few
  years; it does nothing during direct reclaim; and as far as the people
  who examined the patchset can tell, it's moving the codebase in the
  right direction.

  However, as it was a late addition to for-next, I'm holding off on
  that section for another week of testing to see if anyone can come up
  with a solid reason for holding off in the meantime.

  Summary:

   - Skip writeback for pages that are completely beyond EOF

   - Minor code cleanups"

* tag 'iomap-5.20-merge-1' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  dax: set did_zero to true when zeroing successfully
  iomap: set did_zero to true when zeroing successfully
  iomap: skip pages past eof in iomap_do_writepage()

Pull affs fix from David Sterba:
 "One update to AFFS, switching away from the kmap/kmap_atomic API"

* tag 'affs-5.20-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  affs: use memcpy_to_page and remove replace kmap_atomic()

Pull btrfs updates from David Sterba:
 "This brings some long awaited changes, the send protocol bump,
  otherwise lots of small improvements and fixes. The main core part is
  reworking bio handling, cleaning up the submission and endio and
  improving error handling.

  There are some changes outside of btrfs adding helpers or updating
  API, listed at the end of the changelog.

  Features:

   - sysfs:
      - export chunk size, in debug mode add tunable for setting its size
      - show zoned among features (was only in debug mode)
      - show commit stats (number, last/max/total duration)

   - send protocol updated to 2
      - new commands:
         - ability write larger data chunks than 64K
         - send raw compressed extents (uses the encoded data ioctls),
           ie. no decompression on send side, no compression needed on
           receive side if supported
         - send 'otime' (inode creation time) among other timestamps
         - send file attributes (a.k.a file flags and xflags)
      - this is first version bump, backward compatibility on send and
        receive side is provided
      - there are still some known and wanted commands that will be
        implemented in the near future, another version bump will be
        needed, however we want to minimize that to avoid causing
        usability issues

   - print checksum type and implementation at mount time

   - don't print some messages at mount (mentioned as people asked about
     it), we want to print messages namely for new features so let's
     make some space for that
      - big metadata - this has been supported for a long time and is
        not a feature that's worth mentioning
      - skinny metadata - same reason, set by default by mkfs

  Performance improvements:

   - reduced amount of reserved metadata for delayed items
      - when inserted items can be batched into one leaf
      - when deleting batched directory index items
      - when deleting delayed items used for deletion
      - overall improved count of files/sec, decreased subvolume lock
        contention

   - metadata item access bounds checker micro-optimized, with a few
     percent of improved runtime for metadata-heavy operations

   - increase direct io limit for read to 256 sectors, improved
     throughput by 3x on sample workload

  Notable fixes:

   - raid56
      - reduce parity writes, skip sectors of stripe when there are no
        data updates
      - restore reading from on-disk data instead of using stripe cache,
        this reduces chances to damage correct data due to RMW cycle

   - refuse to replay log with unknown incompat read-only feature bit
     set

   - zoned
      - fix page locking when COW fails in the middle of allocation
      - improved tracking of active zones, ZNS drives may limit the
        number and there are ENOSPC errors due to that limit and not
        actual lack of space
      - adjust maximum extent size for zone append so it does not cause
        late ENOSPC due to underreservation

   - mirror reading error messages show the mirror number

   - don't fallback to buffered IO for NOWAIT direct IO writes, we don't
     have the NOWAIT semantics for buffered io yet

   - send, fix sending link commands for existing file paths when there
     are deleted and created hardlinks for same files

   - repair all mirrors for profiles with more than 1 copy (raid1c34)

   - fix repair of compressed extents, unify where error detection and
     repair happen

  Core changes:

   - bio completion cleanups
      - don't double defer compression bios
      - simplify endio workqueues
      - add more data to btrfs_bio to avoid allocation for read requests
      - rework bio error handling so it's same what block layer does,
        the submission works and errors are consumed in endio
      - when asynchronous bio offload fails fall back to synchronous
        checksum calculation to avoid errors under writeback or memory
        pressure

   - new trace points
      - raid56 events
      - ordered extent operations

   - super block log_root_transid deprecated (never used)

   - mixed_backref and big_metadata sysfs feature files removed, they've
     been default for sufficiently long time, there are no known users
     and mixed_backref could be confused with mixed_groups

  Non-btrfs changes, API updates:

   - minor highmem API update to cover const arguments

   - switch all kmap/kmap_atomic to kmap_local

   - remove redundant flush_dcache_page()

   - address_space_operations::writepage callback removed

   - add bdev_max_segments() helper"

* tag 'for-5.20-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux: (163 commits)
  btrfs: don't call btrfs_page_set_checked in finish_compressed_bio_read
  btrfs: fix repair of compressed extents
  btrfs: remove the start argument to check_data_csum and export
  btrfs: pass a btrfs_bio to btrfs_repair_one_sector
  btrfs: simplify the pending I/O counting in struct compressed_bio
  btrfs: repair all known bad mirrors
  btrfs: merge btrfs_dev_stat_print_on_error with its only caller
  btrfs: join running log transaction when logging new name
  btrfs: simplify error handling in btrfs_lookup_dentry
  btrfs: send: always use the rbtree based inode ref management infrastructure
  btrfs: send: fix sending link commands for existing file paths
  btrfs: send: introduce recorded_ref_alloc and recorded_ref_free
  btrfs: zoned: wait until zone is finished when allocation didn't progress
  btrfs: zoned: write out partially allocated region
  btrfs: zoned: activate necessary block group
  btrfs: zoned: activate metadata block group on flush_space
  btrfs: zoned: disable metadata overcommit for zoned
  btrfs: zoned: introduce space_info->active_total_bytes
  btrfs: zoned: finish least available block group on data bg allocation
  btrfs: let can_allocate_chunk return error
  ...

Pull efivars sysfs interface removal from Ard Biesheuvel:
 "Remove the obsolete 'efivars' sysfs based interface to the EFI
  variable store, now that all users have moved to the efivarfs pseudo
  file system, which was created ~10 years ago to address some
  fundamental shortcomings in the sysfs based driver.

  Move the 'business logic' related to which EFI variables are important
  and may affect the boot flow from the efivars support layer into the
  efivarfs pseudo file system, so it is no longer exposed to other parts
  of the kernel"

* tag 'efi-efivars-removal-for-v5.20' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi:
  efi: vars: Move efivar caching layer into efivarfs
  efi: vars: Switch to new wrapper layer
  efi: vars: Remove deprecated 'efivars' sysfs interface

Pull EFI updates from Ard Biesheuvel:

 - Enable mirrored memory for arm64

 - Fix up several abuses of the efivar API

 - Refactor the efivar API in preparation for moving the 'business
   logic' part of it into efivarfs

 - Enable ACPI PRM on arm64

* tag 'efi-next-for-v5.20' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi: (24 commits)
  ACPI: Move PRM config option under the main ACPI config
  ACPI: Enable Platform Runtime Mechanism(PRM) support on ARM64
  ACPI: PRM: Change handler_addr type to void pointer
  efi: Simplify arch_efi_call_virt() macro
  drivers: fix typo in firmware/efi/memmap.c
  efi: vars: Drop __efivar_entry_iter() helper which is no longer used
  efi: vars: Use locking version to iterate over efivars linked lists
  efi: pstore: Omit efivars caching EFI varstore access layer
  efi: vars: Add thin wrapper around EFI get/set variable interface
  efi: vars: Don't drop lock in the middle of efivar_init()
  pstore: Add priv field to pstore_record for backend specific use
  Input: applespi - avoid efivars API and invoke EFI services directly
  selftests/kexec: remove broken EFI_VARS secure boot fallback check
  brcmfmac: Switch to appropriate helper to load EFI variable contents
  iwlwifi: Switch to proper EFI variable store interface
  media: atomisp_gmin_platform: stop abusing efivar API
  efi: efibc: avoid efivar API for setting variables
  efi: avoid efivars layer when loading SSDTs from variables
  efi: Correct comment on efi_memmap_alloc
  memblock: Disable mirror feature if kernelcore is not specified
  ...

Pull 9p iov_iter fix from Al Viro:
 "net/9p abuses iov_iter primitives - it attempts to copy _from_ a
  destination-only iov_iter when it handles Rerror arriving in reply to
  zero-copy request.   Not hard to fix, fortunately.

  This is a prereq for the iov_iter_get_pages() work in the second part
  of iov_iter series, ended up in a separate branch"

* tag 'pull-work.9p' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  9p: handling Rerror without copy_from_iter_full()

Pull copy_to_iter_mc fix from Al Viro:
 "Backportable fix for copy_to_iter_mc() - the second part of iov_iter
  work will pretty much overwrite this, but would be much harder to
  backport"

* tag 'pull-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  fix short copy handling in copy_mc_pipe_to_iter()

Pull vfs iov_iter updates from Al Viro:
 "Part 1 - isolated cleanups and optimizations.

  One of the goals is to reduce the overhead of using ->read_iter() and
  ->write_iter() instead of ->read()/->write().

  new_sync_{read,write}() has a surprising amount of overhead, in
  particular inside iocb_flags(). That's the explanation for the
  beginning of the series is in this pile; it's not directly
  iov_iter-related, but it's a part of the same work..."

* tag 'pull-work.iov_iter-base' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  first_iovec_segment(): just return address
  iov_iter: massage calling conventions for first_{iovec,bvec}_segment()
  iov_iter: first_{iovec,bvec}_segment() - simplify a bit
  iov_iter: lift dealing with maxpages out of first_{iovec,bvec}_segment()
  iov_iter_get_pages{,_alloc}(): cap the maxsize with MAX_RW_COUNT
  iov_iter_bvec_advance(): don't bother with bvec_iter
  copy_page_{to,from}_iter(): switch iovec variants to generic
  keep iocb_flags() result cached in struct file
  iocb: delay evaluation of IS_SYNC(...) until we want to check IOCB_DSYNC
  struct file: use anonymous union member for rcuhead and llist
  btrfs: use IOMAP_DIO_NOSYNC
  teach iomap_dio_rw() to suppress dsync
  No need of likely/unlikely on calls of check_copy_size()

Pull vfs dcache updates from Al Viro:
 "The main part here is making parallel lookups safe for RT - making
  sure preemption is disabled in start_dir_add()/ end_dir_add() sections
  (on non-RT it's automatic, on RT it needs to to be done explicitly)
  and moving wakeups from __d_lookup_done() inside of such to the end of
  those sections.

  Wakeups can be safely delayed for as long as ->d_lock on in-lookup
  dentry is held; proving that has caught a bug in d_add_ci() that
  allows memory corruption when sufficiently bogus ntfs (or
  case-insensitive xfs) image is mounted. Easily fixed, fortunately"

* tag 'pull-work.dcache' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  fs/dcache: Move wakeup out of i_seq_dir write held region.
  fs/dcache: Move the wakeup from __d_lookup_done() to the caller.
  fs/dcache: Disable preemption on i_dir_seq write side on PREEMPT_RT
  d_add_ci(): make sure we don't miss d_lookup_done()

Pull vfs lseek updates from Al Viro:
 "Jason's lseek series.

  Saner handling of 'lseek should fail with ESPIPE' - this gets rid of
  the magical no_llseek thing and makes checks consistent.

  In particular, the ad-hoc "can we do splice via internal pipe" checks
  got saner (and somewhat more permissive, which is what Jason had been
  after, AFAICT)"

* tag 'pull-work.lseek' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  fs: remove no_llseek
  fs: check FMODE_LSEEK to control internal pipe splicing
  vfio: do not set FMODE_LSEEK flag
  dma-buf: remove useless FMODE_LSEEK flag
  fs: do not compare against ->llseek
  fs: clear or set FMODE_LSEEK based on llseek function

Pull vfs namei updates from Al Viro:
 "RCU pathwalk cleanups.

  Storing sampled ->d_seq of the next dentry in nameidata simplifies
  life considerably, especially if we delay fetching ->d_inode until
  step_into()"

* tag 'pull-work.namei' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  step_into(): move fetching ->d_inode past handle_mounts()
  lookup_fast(): don't bother with inode
  follow_dotdot{,_rcu}(): don't bother with inode
  step_into(): lose inode argument
  namei: stash the sampled ->d_seq into nameidata
  namei: move clearing LOOKUP_RCU towards rcu_read_unlock()
  switch try_to_unlazy_next() to __legitimize_mnt()
  follow_dotdot{,_rcu}(): change calling conventions
  namei: get rid of pointless unlikely(read_seqcount_retry(...))
  __follow_mount_rcu(): verify that mount_lock remains unchanged

Pull folio updates from Matthew Wilcox:

 - Fix an accounting bug that made NR_FILE_DIRTY grow without limit
   when running xfstests

 - Convert more of mpage to use folios

 - Remove add_to_page_cache() and add_to_page_cache_locked()

 - Convert find_get_pages_range() to filemap_get_folios()

 - Improvements to the read_cache_page() family of functions

 - Remove a few unnecessary checks of PageError

 - Some straightforward filesystem conversions to use folios

 - Split PageMovable users out from address_space_operations into
   their own movable_operations

 - Convert aops->migratepage to aops->migrate_folio

 - Remove nobh support (Christoph Hellwig)

* tag 'folio-6.0' of git://git.infradead.org/users/willy/pagecache: (78 commits)
  fs: remove the NULL get_block case in mpage_writepages
  fs: don't call ->writepage from __mpage_writepage
  fs: remove the nobh helpers
  jfs: stop using the nobh helper
  ext2: remove nobh support
  ntfs3: refactor ntfs_writepages
  mm/folio-compat: Remove migration compatibility functions
  fs: Remove aops->migratepage()
  secretmem: Convert to migrate_folio
  hugetlb: Convert to migrate_folio
  aio: Convert to migrate_folio
  f2fs: Convert to filemap_migrate_folio()
  ubifs: Convert to filemap_migrate_folio()
  btrfs: Convert btrfs_migratepage to migrate_folio
  mm/migrate: Add filemap_migrate_folio()
  mm/migrate: Convert migrate_page() to migrate_folio()
  nfs: Convert to migrate_folio
  btrfs: Convert btree_migratepage to migrate_folio
  mm/migrate: Convert expected_page_refs() to folio_expected_refs()
  mm/migrate: Convert buffer_migrate_page() to buffer_migrate_folio()
  ...

Pull XArray/IDR updates from Matthew Wilcox:

 - Add appropriate might_alloc() annotations to the XArray APIs

 - Document that the IDR is deprecated

* tag 'xarray-6.0' of git://git.infradead.org/users/willy/xarray:
  IDR: Note that the IDR API is deprecated
  XArray: Add calls to might_alloc()

Pull cgroup updates from Tejun Heo:
 "Several core optimizations:

   - threadgroup_rwsem write locking is skipped when configuring
     controllers in empty subtrees.

     Combined with CLONE_INTO_CGROUP, this allows the common static
     usage pattern to not grab threadgroup_rwsem at all (glibc still
     doesn't seem ready for CLONE_INTO_CGROUP unfortunately).

   - threadgroup_rwsem used to be put into non-percpu mode by default
     due to latency concerns in specific use cases. There's no reason
     for everyone else to pay for it. Make the behavior optional.

   - psi no longer allocates memory when disabled.

  ... along with some code cleanups"

* tag 'cgroup-for-5.20' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
  cgroup: Skip subtree root in cgroup_update_dfl_csses()
  cgroup: remove "no" prefixed mount options
  cgroup: Make !percpu threadgroup_rwsem operations optional
  cgroup: Add "no" prefixed mount options
  cgroup: Elide write-locking threadgroup_rwsem when updating csses on an empty subtree
  cgroup.c: remove redundant check for mixable cgroup in cgroup_migrate_vet_dst
  cgroup.c: add helper __cset_cgroup_from_root to cleanup duplicated codes
  psi: dont alloc memory for psi by default

Conflicts:

net/ax25/af_ax25.c
  d7c4c9e0 ("ax25: fix incorrect dev_tracker usage")
  d62607c3 ("net: rename reference+tracking helpers")

drivers/net/netdevsim/fib.c
  180a6a3e ("netdevsim: fib: Fix reference count leak on route deletion failure")
  012ec02a ("netdevsim: convert driver to use unlocked devlink API during init/fini")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

The commit in Fixes: has changed a .txt file into a .yaml file. Update the
documentation accordingly.

While at it add some `` around some file names to improve the output.

Fixes: 70991f1e ("dt-bindings: net: convert sff,sfp to dtschema")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/be3c7e87ca7f027703247eccfe000b8e34805094.1659247114.git.christophe.jaillet@wanadoo.frSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Merge tag 'flexible-array-transformations-UAPI-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux

Pull uapi flexible array update from Gustavo Silva:
 "A treewide patch that replaces zero-length arrays with flexible-array
  members in UAPI. This has been baking in linux-next for 5 weeks now.

  '-fstrict-flex-arrays=3' is coming and we need to land these changes
  to prevent issues like these in the short future:

    fs/minix/dir.c:337:3: warning: 'strcpy' will always overflow; destination buffer has size 0, but the source string has length 2 (including NUL byte) [-Wfortify-source]
		strcpy(de3->name, ".");
		^

  Since these are all [0] to [] changes, the risk to UAPI is nearly
  zero. If this breaks anything, we can use a union with a new member
  name"

Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=101836

* tag 'flexible-array-transformations-UAPI-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux:
  treewide: uapi: Replace zero-length arrays with flexible-array members

Merge tag 'linux-kselftest-next-5.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest

Pull Kselftest updates from Shuah Khan:

 - timers test build fixes and cleanups for new tool chains

 - removing khdr from kselftest framework and main Makefile

 - changes to test output messages to improve reports

* tag 'linux-kselftest-next-5.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest: (24 commits)
  Makefile: replace headers_install with headers for kselftest
  selftests/landlock: drop deprecated headers dependency
  selftests: timers: clocksource-switch: adapt to kselftest framework
  selftests: timers: clocksource-switch: add 'runtime' command line parameter
  selftests: timers: clocksource-switch: add command line switch to skip sanity check
  selftests: timers: clocksource-switch: sort includes
  selftests: timers: clocksource-switch: fix passing errors from child
  selftests: timers: inconsistency-check: adapt to kselftest framework
  selftests: timers: nanosleep: adapt to kselftest framework
  selftests: timers: fix declarations of main()
  selftests: timers: valid-adjtimex: build fix for newer toolchains
  Makefile: add headers_install to kselftest targets
  selftests: drop KSFT_KHDR_INSTALL make target
  selftests: stop using KSFT_KHDR_INSTALL
  selftests: drop khdr make target
  selftests: drivers/dma-buf: Improve message in selftest summary
  selftests/kcmp: Make the test output consistent and clear
  selftests:timers: globals don't need initialization to 0
  selftests/drivers/gpu: Add error messages to drm_mm.sh
  selftests/tpm2: increase timeout for kselftests
  ...