- 28 Aug, 2009 40 commits
-
-
Jussi Kivilinna authored
Add cfg80211 get_station and convert SIOCGIWRATE and get_wireless_stats to cfg80211. Signed-off-by:
Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Jussi Kivilinna authored
Add cfg80211 add_key/del_key/set_default_key and convert wext to use theim. Signed-off-by:
-
Jussi Kivilinna authored
Add cfg80211 set_channel and convert wext to use it. Signed-off-by:
-
Jussi Kivilinna authored
Add cfg80211 connect functions for station and ad-hoc modes and convert wext to use theim. Signed-off-by:
-
Jussi Kivilinna authored
Random essid must be set to turn on radio when not connected. If device is in ad-hoc mode, this results 'media connect' indications with the random essid which should be ignored. Signed-off-by:
-
Jussi Kivilinna authored
Signed-off-by:
-
Jussi Kivilinna authored
Use is_zero_ether_addr() and is_broadcast_ether_addr() instead of memcmp against ffff_bssid/zero_bssid. Signed-off-by:
-
Jussi Kivilinna authored
Move link up/down work to separate functions and use local array for allocating memory for info structure instead of kzmalloc. Signed-off-by:
-
Jussi Kivilinna authored
Increase scan delay from 1 sec to 6 sec. Spec says that scan by OID_802_11_BSSID_LIST_SCAN completes in 6 seconds. Before rfkill patch too short delay was not problem as device was always active (radio on) and performing background scanning. Signed-off-by:
-
Jussi Kivilinna authored
Buffer used for bssid list might be too small. Change rndis_query_oid() to return required buffer length to caller and make rndis_check_bssid_list() resize buffer when needed. Signed-off-by:
-
Jussi Kivilinna authored
OID_802_11_BSSID_LIST_SCAN clears device's bssid list, so retrieve current bssid list from device before issuing new scan. Signed-off-by:
-
Jussi Kivilinna authored
Setting WPA keys with OID_802_11_ADD_KEY sometimes trigger instant media connect indication. These indications are extranous and should be ignored, as otherwise driver would send reassociation event to userspace which in this case is not needed. Signed-off-by:
-
Gábor Stefanik authored
The A/G-PHY changes are fallout fixes from the enum change, which in turn allows the LP-PHY code to be much simpler. The antenna_to_phyctl change is a fix for a potential existing bug that this patch may otherwise trigger. Signed-off-by:
Gábor Stefanik <netrolller.3d@gmail.com> Signed-off-by:
-
Gábor Stefanik authored
The most common LP-PHY device, BCM4312, is now fully functional. So, no need to say "probably won't work for you" anymore. It's also not "for debuggers and developers only", as it is perfectly usable for end-users now (at least for BCM4312). Signed-off-by:
-
Pavel Roskin authored
AR5K_SREV is available even if the chip has been put to sleep. Relying on the chip register allows binding non-standard PCI IDs by echo VENDOR_ID PRODUCT_ID >/sys/bus/pci/drivers/ath5k/new_id without having to specify the driver data as well. Signed-off-by:
Pavel Roskin <proski@gnu.org> Acked-by:
Bob Copeland <me@bobcopeland.com> Acked-by:
Nick Kossifidis <mickflemm@gmail.com> Signed-off-by:
-
Pavel Roskin authored
The `val' variable in ath5k_eeprom_read_turbo_modes() is used uninitialized. gcc 4.4.1 with -fno-inline-functions-called-once reports it: eeprom.c: In function 'ath5k_eeprom_read_turbo_modes': eeprom.c:441: warning: 'val' may be used uninitialized in this function Comparing the code to the Atheros HAL, it's clear that the split between ath5k_eeprom_read_modes() and ath5k_eeprom_read_turbo_modes() was incorrect. The Atheros HAL reads both turbo and non-turbo data from EEPROM in one function. Some turbo mode parameters are derived from the same EEPROM values as non-turbo parameters, just from different bits. Merge ath5k_eeprom_read_turbo_modes() into ath5k_eeprom_read_modes() to fix the warning. The actual values and offsets have been cross-checked against Atheros HAL. Signed-off-by:
-
Bob Copeland authored
As Pavel Roskin noted, the check for mac version as copied from legacy_hal made no sense. This replaces it with the equivalent and makes up a suitable #define for the mac version legacy_hal checked. Signed-off-by:
-
Gábor Stefanik authored
After some discussion on IRC about the PHY register write change, I am not sure anymore if this is the right thing to do. Signed-off-by:
-
Johannes Berg authored
The ICT IRQ table is a set of __le32 values, not u32 values, so when reading it we need to take into account that it has to be converted to CPU endianness. This was causing a lot of trouble on my powerpc box where various things would simply not work for no apparent reason with 5xxx cards, but worked with 4965 -- which doesn't use the ICT table. Signed-off-by:
Johannes Berg <johannes@sipsolutions.net> Acked-by:
Reinette Chatre <reinette.chatre@intel.com> Signed-off-by:
-
Ivo van Doorn authored
Since patch "rt2x00: bss_info_changed() callback is allowed to sleep" the variable delayed wasn't used anymore. This means it can be removed along with the call to schedule_work which depended on that variable. Signed-off-by:
Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by:
-
Gábor Stefanik authored
Implement the "PMU LDO set voltage" and "PMU LDO PA ref enable" functions, and use them during LP-PHY baseband init in b43. Signed-off-by:
-
Gábor Stefanik authored
-Fix a few nasty typos (b43_phy_* operations instead of b43_radio_*) in the channel tune routines. -Fix some typos & spec errors found by MMIO tracing. -Optimize b43_phy_write & b43_phy_mask/set/maskset to use only the minimal number of MMIO accesses. (Write is possible using a single 32-bit MMIO write, while set/mask/maskset can be done in 3 16-bit MMIOs). -Set the default channel back to 1, as the bug forcing us to use channel 7 is now fixed. With this, the device comes up, scans, associates, transmits, receives, monitors and injects on all channels - in other words, it's fully functional. Sensitivity and TX power are still sub-optimal, due to the lack of calibration (that's next on my list). Signed-off-by:
-
Gábor Stefanik authored
The Qdiv roundup routine is essentially a fixed-point division algorithm, using only integer math. However, the version in the specs had a major error that has been recently fixed (a missing quotient++). Replace Qdiv roundup with a rewritten, simplified version. Signed-off-by:
-
Herton Ronaldo Krzesinski authored
This change implements rfkill support for RTL8187B and RTL8187L devices, using new cfg80211 rfkill API. Acked-by:
Larry Finger <Larry.Finger@lwfinger.net> Tested-by:
Hin-Tak Leung <htl10@users.sourceforge.net> Signed-off-by:
Herton Ronaldo Krzesinski <herton@mandriva.com.br> Signed-off-by:
-
Herton Ronaldo Krzesinski authored
Larry Finger reports following lockdep warning: [ INFO: possible circular locking dependency detected ] 2.6.31-rc6-wl #201 ------------------------------------------------------- rfkill/30578 is trying to acquire lock: (&(&priv->work)->work#2){+.+...}, at: [<ffffffff81051215>] __cancel_work_timer+0xd9/0x222 but task is already holding lock: (&priv->conf_mutex#2){+.+.+.}, at: [<ffffffffa064a024>] rtl8187_stop+0x31/0x364 [rtl8187] which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #1 (&priv->conf_mutex#2){+.+.+.}: [<ffffffff81065957>] __lock_acquire+0x12d0/0x1614 [<ffffffff81065d54>] lock_acquire+0xb9/0xdd [<ffffffff8127c32f>] mutex_lock_nested+0x56/0x2a8 [<ffffffffa064a392>] rtl8187_work+0x3b/0xf2 [rtl8187] [<ffffffff81050758>] worker_thread+0x1fa/0x30a [<ffffffff81054ca5>] kthread+0x8f/0x97 [<ffffffff8100cb7a>] child_rip+0xa/0x20 [<ffffffffffffffff>] 0xffffffffffffffff -> #0 (&(&priv->work)->work#2){+.+...}: [<ffffffff8106568c>] __lock_acquire+0x1005/0x1614 [<ffffffff81065d54>] lock_acquire+0xb9/0xdd [<ffffffff8105124e>] __cancel_work_timer+0x112/0x222 [<ffffffff8105136b>] cancel_delayed_work_sync+0xd/0xf [<ffffffffa064a33f>] rtl8187_stop+0x34c/0x364 [rtl8187] [<ffffffffa0242866>] ieee80211_stop_device+0x29/0x61 [mac80211] [<ffffffffa0239194>] ieee80211_stop+0x476/0x530 [mac80211] [<ffffffff8120ce15>] dev_close+0x8a/0xac [<ffffffffa01d9fa7>] cfg80211_rfkill_set_block+0x4a/0x7a [cfg80211] [<ffffffffa01bf4f0>] rfkill_set_block+0x84/0xd9 [rfkill] [<ffffffffa01bfc31>] rfkill_fop_write+0xda/0x124 [rfkill] [<ffffffff810cf286>] vfs_write+0xae/0x14a [<ffffffff810cf3e6>] sys_write+0x47/0x6e [<ffffffff8100ba6b>] system_call_fastpath+0x16/0x1b [<ffffffffffffffff>] 0xffffffffffffffff The problem here is that rtl8187_stop, while helding priv->conf_mutex, runs cancel_delayed_work_sync on an workqueue that runs rtl8187_work, which also takes priv->conf_mutex lock. Move cancel_delayed_work_sync out of rtl8187_stop priv->conf_mutex locking region. Reported-by: -
Vasanthakumar Thiagarajan authored
This patch adds 3-wire bluetooth coex support for AR9285. This support can be enabled through btcoex_enable modparam. Signed-off-by:
Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by:
-
Vasanthakumar Thiagarajan authored
Signed-off-by:
-
Vasanthakumar Thiagarajan authored
We don't need a hw cap bit for btcoex anymore as btcoex scheme type is enough to do this. Signed-off-by:
-
Vasanthakumar Thiagarajan authored
Signed-off-by:
-
Vasanthakumar Thiagarajan authored
Also define macros for wlanactive and btactive (5 & 6) gpios. Signed-off-by:
-
Vasanthakumar Thiagarajan authored
Make sure btcoex register configured with appropriate values after it is initialized with the default values from initvals.h during reset. Signed-off-by:
-
Vasanthakumar Thiagarajan authored
Signed-off-by:
-
Vasanthakumar Thiagarajan authored
This function currently does initialization + enable the btcoex support. Split it into two logical functions which does the above operations separately. Btcoex initialization is done during attach time and enabling this feature is done in start(). Also, add code to disable btcoex support in stop(). Signed-off-by:
-
Jussi Kivilinna authored
rndis_wlan does not set cipher suites list for cfg80211 which causes wext-compat-range to report rndis_wlan not supporting WPA. Patch adds cipher suites list and fixes NetworkManager not being able to connect to WPA encrypted APs. Signed-off-by:
-
Sujith authored
When dumping register contents, HW has to be awake. Signed-off-by:
Sujith <Sujith.Manoharan@atheros.com> Signed-off-by:
-
Sujith authored
Signed-off-by:
-
Sujith authored
PA Calibration is not needed for high power solutions. Signed-off-by:
-
Sujith authored
* First PA driver (PDPADRV1) was not powered down properly. * Compensation capacitor for dynamic PA was programmed incorrectly. Also, remove a stray REG_READ. Signed-off-by:
-
Sujith authored
PA calibration need not be done if the offset is not varying. The current logic does PA calibration even if the offset is the same. Signed-off-by:
-
John W. Linville authored
Initiate the conversion of libipw to the new cfg80211 configuration API. For now, leave CONFIG_IPW2200_PROMISCUOUS stuff alone. Eventually migrate it to cfg80211 when the add/del/change_virtual_intf methods are implemented. Signed-off-by:
-
