The descriptor list is a shared resource across all of the transmit queues, and
the locking mechanism used today only protects concurrency across a given
transmit queue between the transmit and reclaiming. This creates an opportunity
for the SYSTEMPORT hardware to work on corrupted descriptors if we have
multiple producers at once which is the case when using multiple transmit
queues.

This was particularly noticeable when using multiple flows/transmit queues and
it showed up in interesting ways in that UDP packets would get a correct UDP
header checksum being calculated over an incorrect packet length. Similarly TCP
packets would get an equally correct checksum computed by the hardware over an
incorrect packet length.

The SYSTEMPORT hardware maintains an internal descriptor list that it re-arranges
when the driver produces a new descriptor anytime it writes to the
WRITE_PORT_{HI,LO} registers, there is however some delay in the hardware to
re-organize its descriptors and it is possible that concurrent TX queues
eventually break this internal allocation scheme to the point where the
length/status part of the descriptor gets used for an incorrect data buffer.

The fix is to impose a global serialization for all TX queues in the short
section where we are writing to the WRITE_PORT_{HI,LO} registers which solves
the corruption even with multiple concurrent TX queues being used.

Fixes: 80105bef ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20211215202450.4086240-1-f.fainelli@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

In nginx/wrk benchmark, there's a hung problem with high probability
on case likes that: (client will last several minutes to exit)

server: smc_run nginx

client: smc_run wrk -c 10000 -t 1 http://server

Client hangs with the following backtrace:

0 [ffffa7ce8Of3bbf8] __schedule at ffffffff9f9eOd5f
1 [ffffa7ce8Of3bc88] schedule at ffffffff9f9eløe6
2 [ffffa7ce8Of3bcaO] schedule_timeout at ffffffff9f9e3f3c
3 [ffffa7ce8Of3bd2O] wait_for_common at ffffffff9f9el9de
4 [ffffa7ce8Of3bd8O] __flush_work at ffffffff9fOfeOl3
5 [ffffa7ce8øf3bdfO] smc_release at ffffffffcO697d24 [smc]
6 [ffffa7ce8Of3be2O] __sock_release at ffffffff9f8O2e2d
7 [ffffa7ce8Of3be4ø] sock_close at ffffffff9f8ø2ebl
8 [ffffa7ce8øf3be48] __fput at ffffffff9f334f93
9 [ffffa7ce8Of3be78] task_work_run at ffffffff9flOlff5
10 [ffffa7ce8Of3beaO] do_exit at ffffffff9fOe5Ol2
11 [ffffa7ce8Of3bflO] do_group_exit at ffffffff9fOe592a
12 [ffffa7ce8Of3bf38] __x64_sys_exit_group at ffffffff9fOe5994
13 [ffffa7ce8Of3bf4O] do_syscall_64 at ffffffff9f9d4373
14 [ffffa7ce8Of3bfsO] entry_SYSCALL_64_after_hwframe at ffffffff9fa0007c

This issue dues to flush_work(), which is used to wait for
smc_connect_work() to finish in smc_release(). Once lots of
smc_connect_work() was pending or all executing work dangling,
smc_release() has to block until one worker comes to free, which
is equivalent to wait another smc_connnect_work() to finish.

In order to fix this, There are two changes:

1. For those idle smc_connect_work(), cancel it from the workqueue; for
   executing smc_connect_work(), waiting for it to finish. For that
   purpose, replace flush_work() with cancel_work_sync().

2. Since smc_connect() hold a reference for passive closing, if
   smc_connect_work() has been cancelled, release the reference.

Fixes: 24ac3a08 ("net/smc: rebuild nonblocking connect")
Reported-by: Tony Lu <tonylu@linux.alibaba.com>
Tested-by: Dust Li <dust.li@linux.alibaba.com>
Reviewed-by: Dust Li <dust.li@linux.alibaba.com>
Reviewed-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: D. Wythe <alibuda@linux.alibaba.com>
Acked-by: Karsten Graul <kgraul@linux.ibm.com>
Link: https://lore.kernel.org/r/1639571361-101128-1-git-send-email-alibuda@linux.alibaba.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

When printing netdev features %pNF already takes care of the 0x prefix,
remove the explicit one.

Fixes: 6413139d ("skbuff: increase verbosity when dumping skb data")
Signed-off-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We found the stat of rx drops for small pkts does not increment when
build_skb fail, it's not coherent with other mode's rx drops stat.
Signed-off-by: Wenliang Wang <wangwenliang.1995@bytedance.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Debug print uses invalid check to detect if speed is unforced:
(speed != SPEED_UNFORCED) should be used instead of (!speed).

Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Andrey Eremeev <Axtone4all@yandex.ru>
Fixes: 96a2b40c ("net: dsa: mv88e6xxx: add port's MAC speed setter")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The return value of kmalloc() needs to be checked.
To avoid use in efx_nic_update_stats() in case of the failure of alloc.

Fixes: b593b6f1 ("sfc_ef100: statistics gathering")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

KASAN reports an out-of-bounds read in rk_gmac_setup on the line:

	while (ops->regs[i]) {

This happens for most platforms since the regs flexible array member is
empty, so the memory after the ops structure is being read here.  It
seems that mostly this happens to contain zero anyway, so we get lucky
and everything still works.

To avoid adding redundant data to nearly all the ops structures, add a
new flag to indicate whether the regs field is valid and avoid this loop
when it is not.

Fixes: 3bb3d6b1 ("net: stmmac: Add RK3566/RK3568 SoC support")
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tony Nguyen says:

====================
Intel Wired LAN Driver Updates 2021-12-15

This series contains updates to igb, igbvf, igc and ixgbe drivers.

Karen moves checks for invalid VF MAC filters to occur earlier for
igb.

Letu Ren fixes a double free issue in igbvf probe.

Sasha fixes incorrect min value being used when calculating for max for
igc.

Robert Schlabbach adds documentation on enabling NBASE-T support for
ixgbe.

Cyril Novikov adds missing initialization of MDIO bus speed for ixgbe.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds the vendor and product IDs for the AT29M2-AF which is a
lan7801-based device.
Signed-off-by: Greg Jesionowski <jesionowskigreg@gmail.com>
Link: https://lore.kernel.org/r/20211214221027.305784-1-jesionowskigreg@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Packet sockets may switch ring versions. Avoid misinterpreting state
between versions, whose fields share a union. rx_owner_map is only
allocated with a packet ring (pg_vec) and both are swapped together.
If pg_vec is NULL, meaning no packet ring was allocated, then neither
was rx_owner_map. And the field may be old state from a tpacket_v3.

Fixes: 61fad681 ("net/packet: tpacket_rcv: avoid a producer race condition")
Reported-by: Syzbot <syzbot+1ac0994a0a0c55151121@syzkaller.appspotmail.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20211215143937.106178-1-willemdebruijn.kernel@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Zero-initialize memory for new map's value in function nsim_bpf_map_alloc
since it may cause a potential kernel information leak issue, as follows:
1. nsim_bpf_map_alloc calls nsim_map_alloc_elem to allocate elements for
a new map.
2. nsim_map_alloc_elem uses kmalloc to allocate map's value, but doesn't
zero it.
3. A user application can use IOCTL BPF_MAP_LOOKUP_ELEM to get specific
element's information in the map.
4. The kernel function map_lookup_elem will call bpf_map_copy_value to get
the information allocated at step-2, then use copy_to_user to copy to the
user buffer.
This can only leak information for an array map.

Fixes: 395cacb5 ("netdevsim: bpf: support fake map offload")
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Haimin Zhang <tcs.kernel@gmail.com>
Link: https://lore.kernel.org/r/20211215111530.72103-1-tcs.kernel@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Unfortunately, with the blamed commit I also added a side effect in the
ethtool stats shown. Because I added two more fields in the per channel
structure without verifying if its size is used in any way, part of the
ethtool statistics were off by 2.
Fix this by not looking up the size of the structure but instead on a
fixed value kept in a macro.

Fixes: fc398bec ("net: dpaa2: add adaptive interrupt coalescing")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/20211215105831.290070-1-ioana.ciornei@nxp.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The MDIO bus speed must be initialized before talking to the PHY the first
time in order to avoid talking to it using a speed that the PHY doesn't
support.

This fixes HW initialization error -17 (IXGBE_ERR_PHY_ADDR_INVALID) on
Denverton CPUs (a.k.a. the Atom C3000 family) on ports with a 10Gb network
plugged in. On those devices, HLREG0[MDCSPD] resets to 1, which combined
with the 10Gb network results in a 24MHz MDIO speed, which is apparently
too fast for the connected PHY. PHY register reads over MDIO bus return
garbage, leading to initialization failure.

Reproduced with Linux kernel 4.19 and 5.15-rc7. Can be reproduced using
the following setup:

* Use an Atom C3000 family system with at least one X552 LAN on the SoC
* Disable PXE or other BIOS network initialization if possible
  (the interface must not be initialized before Linux boots)
* Connect a live 10Gb Ethernet cable to an X550 port
* Power cycle (not reset, doesn't always work) the system and boot Linux
* Observe: ixgbe interfaces w/ 10GbE cables plugged in fail with error -17

Fixes: e84db727 ("ixgbe: Introduce function to control MDIO speed")
Signed-off-by: Cyril Novikov <cnovikov@lynx.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Commit a296d665 ("ixgbe: Add ethtool support to enable 2.5 and 5.0
Gbps support") introduced suppression of the advertisement of NBASE-T
speeds by default, according to Todd Fujinaka to accommodate customers
with network switches which could not cope with advertised NBASE-T
speeds, as posted in the E1000-devel mailing list:

https://sourceforge.net/p/e1000/mailman/message/37106269/

However, the suppression was not documented at all, nor was how to
enable NBASE-T support.

Properly document the NBASE-T suppression and how to enable NBASE-T
support.

Fixes: a296d665 ("ixgbe: Add ethtool support to enable 2.5 and 5.0 Gbps support")
Reported-by: Robert Schlabbach <robert_s@gmx.net>
Signed-off-by: Robert Schlabbach <robert_s@gmx.net>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

The LTR maximum value was incorrectly written using the scale from
the LTR minimum value. This would cause incorrect values to be sent,
in cases where the initial calculation lead to different min/max scales.

Fixes: 707abf06 ("igc: Add initial LTR support")
Suggested-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

In `igbvf_probe`, if register_netdev() fails, the program will go to
label err_hw_init, and then to label err_ioremap. In free_netdev() which
is just below label err_ioremap, there is `list_for_each_entry_safe` and
`netif_napi_del` which aims to delete all entries in `dev->napi_list`.
The program has added an entry `adapter->rx_ring->napi` which is added by
`netif_napi_add` in igbvf_alloc_queues(). However, adapter->rx_ring has
been freed below label err_hw_init. So this a UAF.

In terms of how to patch the problem, we can refer to igbvf_remove() and
delete the entry before `adapter->rx_ring`.

The KASAN logs are as follows:

[   35.126075] BUG: KASAN: use-after-free in free_netdev+0x1fd/0x450
[   35.127170] Read of size 8 at addr ffff88810126d990 by task modprobe/366
[   35.128360]
[   35.128643] CPU: 1 PID: 366 Comm: modprobe Not tainted 5.15.0-rc2+ #14
[   35.129789] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.0-59-gc9ba5276e321-prebuilt.qemu.org 04/01/2014
[   35.131749] Call Trace:
[   35.132199]  dump_stack_lvl+0x59/0x7b
[   35.132865]  print_address_description+0x7c/0x3b0
[   35.133707]  ? free_netdev+0x1fd/0x450
[   35.134378]  __kasan_report+0x160/0x1c0
[   35.135063]  ? free_netdev+0x1fd/0x450
[   35.135738]  kasan_report+0x4b/0x70
[   35.136367]  free_netdev+0x1fd/0x450
[   35.137006]  igbvf_probe+0x121d/0x1a10 [igbvf]
[   35.137808]  ? igbvf_vlan_rx_add_vid+0x100/0x100 [igbvf]
[   35.138751]  local_pci_probe+0x13c/0x1f0
[   35.139461]  pci_device_probe+0x37e/0x6c0
[   35.165526]
[   35.165806] Allocated by task 366:
[   35.166414]  ____kasan_kmalloc+0xc4/0xf0
[   35.167117]  foo_kmem_cache_alloc_trace+0x3c/0x50 [igbvf]
[   35.168078]  igbvf_probe+0x9c5/0x1a10 [igbvf]
[   35.168866]  local_pci_probe+0x13c/0x1f0
[   35.169565]  pci_device_probe+0x37e/0x6c0
[   35.179713]
[   35.179993] Freed by task 366:
[   35.180539]  kasan_set_track+0x4c/0x80
[   35.181211]  kasan_set_free_info+0x1f/0x40
[   35.181942]  ____kasan_slab_free+0x103/0x140
[   35.182703]  kfree+0xe3/0x250
[   35.183239]  igbvf_probe+0x1173/0x1a10 [igbvf]
[   35.184040]  local_pci_probe+0x13c/0x1f0

Fixes: d4e0fe01 (igbvf: add new driver to support 82576 virtual functions)
Reported-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Letu Ren <fantasquex@gmail.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Move checking condition of VF MAC filter before clearing
or adding MAC filter to VF to prevent potential blackout caused
by removal of necessary and working VF's MAC filter.

Fixes: 1b8b062a ("igb: add VF trust infrastructure")
Signed-off-by: Karen Sornek <karen.sornek@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Merge tag 'wireless-drivers-2021-12-15' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers

Kalle Valo says:

====================
wireless-drivers fixes for v5.16

Second set of fixes for v5.16, hopefully also the last one. I changed
my email in MAINTAINERS, one crash fix in iwlwifi and some build
problems fixed.

iwlwifi

* fix crash caused by a warning

* fix LED linking problem

brcmsmac

* rework LED dependencies for being consistent with other drivers

mt76

* mt7921: fix build regression
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Tony Nguyen says:

====================
Intel Wired LAN Driver Updates 2021-12-14

This series contains updates to ice driver only.

Karol corrects division that was causing incorrect calculations and
adds a check to ensure stale timestamps are not being used.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Mat Martineau says:

====================
mptcp: Fixes for ULP, a deadlock, and netlink docs

Two of the MPTCP fixes in this set are related to the TCP_ULP socket
option with MPTCP sockets operating in "fallback" mode (the connection
has reverted to regular TCP). The other issues are an observed deadlock
and missing parameter documentation in the MPTCP netlink API.

Patch 1 marks TCP_ULP as unsupported earlier in MPTCP setsockopt code,
so the fallback code path in the MPTCP layer does not pass the TCP_ULP
option down to the subflow TCP socket.

Patch 2 makes sure a TCP fallback socket returned to userspace by
accept()ing on a MPTCP listening socket does not allow use of the
"mptcp" TCP_ULP type. That ULP is intended only for use by in-kernel
MPTCP subflows.

Patch 3 fixes the possible deadlock when sending data and there are
socket option changes to sync to the subflows.

Patch 4 makes sure all MPTCP netlink event parameters are documented
in the MPTCP uapi header.
====================

Link: https://lore.kernel.org/r/20211214231604.211016-1-mathew.j.martineau@linux.intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

'loc_id' and 'rem_id' are set in all events linked to subflows but those
were missing in the events description in the comments.

Fixes: b911c97c ("mptcp: add netlink event support")
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

__mptcp_push_pending() may call mptcp_flush_join_list() with subflow
socket lock held. If such call hits mptcp_sockopt_sync_all() then
subsequently __mptcp_sockopt_sync() could try to lock the subflow
socket for itself, causing a deadlock.

sysrq: Show Blocked State
task:ss-server       state:D stack:    0 pid:  938 ppid:     1 flags:0x00000000
Call Trace:
 <TASK>
 __schedule+0x2d6/0x10c0
 ? __mod_memcg_state+0x4d/0x70
 ? csum_partial+0xd/0x20
 ? _raw_spin_lock_irqsave+0x26/0x50
 schedule+0x4e/0xc0
 __lock_sock+0x69/0x90
 ? do_wait_intr_irq+0xa0/0xa0
 __lock_sock_fast+0x35/0x50
 mptcp_sockopt_sync_all+0x38/0xc0
 __mptcp_push_pending+0x105/0x200
 mptcp_sendmsg+0x466/0x490
 sock_sendmsg+0x57/0x60
 __sys_sendto+0xf0/0x160
 ? do_wait_intr_irq+0xa0/0xa0
 ? fpregs_restore_userregs+0x12/0xd0
 __x64_sys_sendto+0x20/0x30
 do_syscall_64+0x38/0x90
 entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f9ba546c2d0
RSP: 002b:00007ffdc3b762d8 EFLAGS: 00000246 ORIG_RAX: 000000000000002c
RAX: ffffffffffffffda RBX: 00007f9ba56c8060 RCX: 00007f9ba546c2d0
RDX: 000000000000077a RSI: 0000000000e5e180 RDI: 0000000000000234
RBP: 0000000000cc57f0 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00007f9ba56c8060
R13: 0000000000b6ba60 R14: 0000000000cc7840 R15: 41d8685b1d7901b8
 </TASK>

Fix the issue by using __mptcp_flush_join_list() instead of plain
mptcp_flush_join_list() inside __mptcp_push_pending(), as suggested by
Florian. The sockopt sync will be deferred to the workqueue.

Fixes: 1b3e7ede ("mptcp: setsockopt: handle SO_KEEPALIVE and SO_PRIORITY")
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/244Suggested-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Maxim Galaganov <max@internet.ru>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The mptcp ULP extension relies on sk->sk_sock_kern being set correctly:
It prevents setsockopt(fd, IPPROTO_TCP, TCP_ULP, "mptcp", 6); from
working for plain tcp sockets (any userspace-exposed socket).

But in case of fallback, accept() can return a plain tcp sk.
In such case, sk is still tagged as 'kernel' and setsockopt will work.

This will crash the kernel, The subflow extension has a NULL ctx->conn
mptcp socket:

BUG: KASAN: null-ptr-deref in subflow_data_ready+0x181/0x2b0
Call Trace:
 tcp_data_ready+0xf8/0x370
 [..]

Fixes: cf7da0d6 ("mptcp: Create SUBFLOW socket for incoming connections")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

TCP_ULP setsockopt cannot be used for mptcp because its already
used internally to plumb subflow (tcp) sockets to the mptcp layer.

syzbot managed to trigger a crash for mptcp connections that are
in fallback mode:

KASAN: null-ptr-deref in range [0x0000000000000020-0x0000000000000027]
CPU: 1 PID: 1083 Comm: syz-executor.3 Not tainted 5.16.0-rc2-syzkaller #0
RIP: 0010:tls_build_proto net/tls/tls_main.c:776 [inline]
[..]
 __tcp_set_ulp net/ipv4/tcp_ulp.c:139 [inline]
 tcp_set_ulp+0x428/0x4c0 net/ipv4/tcp_ulp.c:160
 do_tcp_setsockopt+0x455/0x37c0 net/ipv4/tcp.c:3391
 mptcp_setsockopt+0x1b47/0x2400 net/mptcp/sockopt.c:638

Remove support for TCP_ULP setsockopt.

Fixes: d9e4c129 ("mptcp: only admit explicitly supported sockopt")
Reported-by: syzbot+1fd9b69cde42967d1add@syzkaller.appspotmail.com
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The driver has to check if it does not accidentally put the timestamp in
the SKB before previous timestamp gets overwritten.
Timestamp values in the PHY are read only and do not get cleared except
at hardware reset or when a new timestamp value is captured.
The cached_tstamp field is used to detect the case where a new timestamp
has not yet been captured, ensuring that we avoid sending stale
timestamp data to the stack.

Fixes: ea9b847c ("ice: enable transmit timestamps for E810 devices")
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Change the division in ice_ptp_adjfine from div_u64 to div64_u64.
div_u64 is used when the divisor is 32 bit but in this case incval is
64 bit and it caused incorrect calculations and incval adjustments.

Fixes: 06c16d89 ("ice: register 1588 PTP clock device object for E810 devices")
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Ido Schimmel says:

====================
mlxsw: MAC profiles occupancy fix

Patch #1 fixes a router interface (RIF) MAC profiles occupancy bug that
was merged in the last cycle.

Patch #2 adds a selftest that fails without the fix.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a test case to cover the bug fixed by the previous patch.

Edit the MAC address of one netdev so that it matches the MAC address of
the second netdev. Verify that the two MAC profiles were consolidated by
testing that the MAC profiles occupancy decreased by one.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, when setting a router interface (RIF) MAC address while the
MAC profile is not shared with other RIFs, the profile is edited so that
the new MAC address is assigned to it.

This does not take into account a situation in which the new MAC address
already matches an existing MAC profile. In that situation, two MAC
profiles will be occupied even though they hold MAC addresses from the
same profile.

In order to prevent that, add a check to ensure that editing a MAC
profile takes place only when the new MAC address does not match an
existing profile.

Fixes: 605d25cd ("mlxsw: spectrum_router: Add RIF MAC profiles support")
Reported-by: Maksym Yaremchuk <maksymy@nvidia.com>
Tested-by: Maksym Yaremchuk <maksymy@nvidia.com>
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

__rds_conn_create() did not release conn->c_path when loop_trans != 0 and
trans->t_prefer_loopback != 0 and is_outgoing == 0.

Fixes: aced3ce5 ("RDS tcp loopback connection can hang")
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Reviewed-by: Sharath Srinivasan <sharath.srinivasan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'mac80211-for-net-2021-12-14' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211

Johannes Berg says:

====================
A fairly large number of fixes this time:
 * fix a station info memory leak on insert collisions
 * a rate control fix for retransmissions
 * two aggregation setup fixes
 * reload current regdomain when reloading database
 * a locking fix in regulatory work
 * a probe request allocation size fix in mac80211
 * apply TCP vs. aggregation (sk pacing) on mesh
 * fix ordering of channel context update vs. station
   state
 * set up skb->dev for mesh forwarding properly
 * track QoS data frames only for admission control to
   avoid out-of-bounds read (found by syzbot)
 * validate extended element ID vs. existing data to
   avoid out-of-bounds read (found by syzbot)
 * fix locking in mac80211 aggregation TX setup
 * fix traffic stall after HW restart when TXQs are used
 * fix ordering of reconfig/restart after HW restart
 * fix interface type for extended aggregation capability
   lookup
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Tony Nguyen says:

====================
Intel Wired LAN Driver Updates 2021-12-13

This series contains updates to iavf driver only.

Dan Carpenter fixes some missing mutex unlocking.

Stefan Assmann restores stopping watchdog from overriding to reset state.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

We need to return EOPNOTSUPP for the unsupported mpls action type when
setup the flow action.

In the original implement, we will return 0 for the unsupported mpls
action type, actually we do not setup it and the following actions
to the flow action entry.

Fixes: 9838b20a ("net: sched: take rtnl lock in tc_setup_flow_action()")
Signed-off-by: Baowen Zheng <baowen.zheng@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To replicate the issue:-

1) Add 1 flower filter for VLAN Priority based frame steering:-
$ IFDEVNAME=eth0
$ tc qdisc add dev $IFDEVNAME ingress
$ tc qdisc add dev $IFDEVNAME root mqprio num_tc 8 \
   map 0 1 2 3 4 5 6 7 0 0 0 0 0 0 0 0 \
   queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 hw 0
$ tc filter add dev $IFDEVNAME parent ffff: protocol 802.1Q \
   flower vlan_prio 0 hw_tc 0

2) Get the 'pref' id
$ tc filter show dev $IFDEVNAME ingress

3) Delete a specific tc flower record (say pref 49151)
$ tc filter del dev $IFDEVNAME parent ffff: pref 49151

From dmesg, we will observe kernel NULL pointer ooops

[  197.170464] BUG: kernel NULL pointer dereference, address: 0000000000000000
[  197.171367] #PF: supervisor read access in kernel mode
[  197.171367] #PF: error_code(0x0000) - not-present page
[  197.171367] PGD 0 P4D 0
[  197.171367] Oops: 0000 [#1] PREEMPT SMP NOPTI

<snip>

[  197.171367] RIP: 0010:tc_setup_cls+0x20b/0x4a0 [stmmac]

<snip>

[  197.171367] Call Trace:
[  197.171367]  <TASK>
[  197.171367]  ? __stmmac_disable_all_queues+0xa8/0xe0 [stmmac]
[  197.171367]  stmmac_setup_tc_block_cb+0x70/0x110 [stmmac]
[  197.171367]  tc_setup_cb_destroy+0xb3/0x180
[  197.171367]  fl_hw_destroy_filter+0x94/0xc0 [cls_flower]

The above issue is due to previous incorrect implementation of
tc_del_vlan_flow(), shown below, that uses flow_cls_offload_flow_rule()
to get struct flow_rule *rule which is no longer valid for tc filter
delete operation.

  struct flow_rule *rule = flow_cls_offload_flow_rule(cls);
  struct flow_dissector *dissector = rule->match.dissector;

So, to ensure tc_del_vlan_flow() deletes the right VLAN cls record for
earlier configured RX queue (configured by hw_tc) in tc_add_vlan_flow(),
this patch introduces stmmac_rfs_entry as driver-side flow_cls_offload
record for 'RX frame steering' tc flower, currently used for VLAN
priority. The implementation has taken consideration for future extension
to include other type RX frame steering such as EtherType based.

v2:
 - Clean up overly extensive backtrace and rewrite git message to better
   explain the kernel NULL pointer issue.

Fixes: 0e039f5c ("net: stmmac: add RX frame steering based on VLAN priority in tc flower")
Tested-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When we reconfigure, the driver might do some things to complete
the reconfiguration. It's strange and could be broken in some
cases because we restart other works (e.g. remain-on-channel and
TX) before this happens, yet only start queues later.

Change this to do the reconfig complete when reconfiguration is
actually complete, not when we've already started doing other
things again.

For iwlwifi, this should fix a race where the reconfig can race
with TX, for ath10k and ath11k that also use this it won't make
a difference because they just start queues there, and mac80211
also stopped the queues and will restart them later as before.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211129152938.cab99f22fe19.Iefe494687f15fd85f77c1b989d1149c8efdfdc36@changeidSigned-off-by: Johannes Berg <johannes.berg@intel.com>

Mark TXQs as having seen transmit while they were stopped if
we bail out of drv_wake_tx_queue() due to reconfig, so that
the queue wake after this will make them catch up. This is
particularly necessary for when TXQs are used for management
packets since those TXQs won't see a lot of traffic that'd
make them catch up later.

Cc: stable@vger.kernel.org
Fixes: 4856bfd2 ("mac80211: do not call driver wake_tx_queue op during reconfig")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211129152938.4573a221c0e1.I0d1d5daea3089be3fc0dccc92991b0f8c5677f0c@changeidSigned-off-by: Johannes Berg <johannes.berg@intel.com>

Currently channel context is updated only after station got an update about
new assoc state, this results in station using the old channel context.

Fix this by moving the update channel context before updating station,
enabling the driver to immediately use the updated channel context in
the new assoc state.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211129152938.1c80c17ffd8a.I94ae31378b363c1182cfdca46c4b7e7165cff984@changeidSigned-off-by: Johannes Berg <johannes.berg@intel.com>

Instead of using the hard-coded value of '100' use the correct
scan IEs length as calculated during HW registration to mac80211.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211129152938.0a82d6891719.I8ded1f2e0bccb9e71222c945666bcd86537f2e35@changeidSigned-off-by: Johannes Berg <johannes.berg@intel.com>

We should be doing the HE capabilities lookup based on the full
interface type so if P2P doesn't have HE but client has it doesn't
get confused. Fix that.

Fixes: 2ab45876 ("mac80211: add support for the ADDBA extension element")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211129152938.010fc1d61137.If3a468145f29d670cb00a693bed559d8290ba693@changeidSigned-off-by: Johannes Berg <johannes.berg@intel.com>

Before attempting to parse an extended element, verify that
the extended element ID is present.

Fixes: 41cbb0f5 ("mac80211: add support for HE")
Reported-by: syzbot+59bdff68edce82e393b6@syzkaller.appspotmail.com
Link: https://lore.kernel.org/r/20211211201023.f30a1b128c07.I5cacc176da94ba316877c6e10fe3ceec8b4dbd7d@changeid
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>