The trick in socket splicing where we try to convert the skb->data
into a page based reference using virt_to_page() does not work so
well.

The idea is to pass the virt_to_page() reference via the pipe
buffer, and refcount the buffer using a SKB reference.

But if we are splicing from a socket to a socket (via sendpage)
this doesn't work.

The from side processing will grab the page (and SKB) references.
The sendpage() calls will grab page references only, return, and
then the from side processing completes and drops the SKB ref.

The page based reference to skb->data is not enough to keep the
kmalloc() buffer backing it from being reused.  Yet, that is
all that the socket send side has at this point.

This leads to data corruption if the skb->data buffer is reused
by SLAB before the send side socket actually gets the TX packet
out to the device.

The fix employed here is to simply allocate a page and copy the
skb->data bytes into that page.

This will hurt performance, but there is no clear way to fix this
properly without a copy at the present time, and it is important
to get rid of the data corruption.

With fixes from Herbert Xu.
Tested-by: Willy Tarreau <w@1wt.eu>
Foreseen-by: Changli Gao <xiaosuo@gmail.com>
Diagnosed-by: Willy Tarreau <w@1wt.eu>
Reported-by: Willy Tarreau <w@1wt.eu>
Fixed-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch modifies how the tg3 driver handles device firmware.

The patch starts by consolidating David Woodhouse's earlier patch under
the same name.  Specifically, the patch moves the request_firmware call
into a separate tg3_request_firmware() function and calls that function
from tg3_open() rather than tg3_init_one().

The patch then goes on to limit the number of devices that will make
request_firmware calls.  The original firmware patch unnecessarily
requested TSO firmware for devices that did not need it.  This patch
reduces the set of devices making TSO firmware patches to approximately
the following device set : 5703, 5704, and 5705.

Finally, the patch reduces the effects of a request_firmware() failure.
For those devices that are requesting TSO firmware, the driver will turn
off the TSO capability.  If TSO firmware becomes available at a later
time, the device can be closed and then opened again to reacquire the
TSO capability.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netif_carrier_off() is sufficient to stop Tx into the driver.  Stopping the Tx
queues is redundant and unnecessary.  By the same token, netif_carrier_on()
will be sufficient to re-enable Tx, so waking the queues is unnecessary.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Register VLAN ID 0 so that frames with VLAN ID 0 are received and get
their tag stripped when ixgbe is not in DCB mode.  VLAN ID 0 means
that the frame is 'priority tagged' only - it is not a VLAN, but the
priority value is the tag in valid.  The functions
ixgbe_vlan_rx_register() and ixgbe_vlan_rx_kill_vid() were moved up a
couple functions to correct compiling issues with this change.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Eric W Multanen <eric.w.multanen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The is an issue where setting Relaxed Ordering (RO) bit
(in a PCI-E write transaction) on 82598 causing the chipset
to drop DCA hints.  This patch forces RO not to be set for
descriptors as well as payload.  This will only be in effect
while DCA is enabled and no performance difference was
noticed in testing.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

I'm trying to track down why people're hitting the checksum warning
in skb_gso_segment.  As the problem seems to be hitting lots of
people and I can't reproduce it or locate the bug, here is a patch
to print out more details which hopefully should help us to track
this down.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

As the assigned value is being overwritten shortly after, it can be
dropped and so the whole variable definition moved to the start of the
function.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is copy and paste from the original driver. As skb_reserve() is
also called within korina_alloc_ring() when initially allocating the
receive descriptors, the same should be done when allocating new space
after passing an skb to upper layers.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

After the last loop iteration, i has the value RC32434_NUM_RDS and
therefore leads to an index overflow when used afterwards to address the
last element. This is yet another another bug introduced when rewriting
parts of the driver for upstream preparation, as the original driver
used 'RC32434_NUM_RDS - 1' instead.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The lro manager's frag_align_pad setting was missing,
leading to misaligned access to the skb passed up
to the stack.
Tested-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In rare cases when an underrun occur, all macb buffers where consumed
and the netif_queue was stopped infinitely. This happens then the TGO
(transfer ongoing) bit in the TSR is set (and UND). It seems like
clening up after the underrun makes the driver and the macb hardware
end up in an inconsistent state. The result of this is that in the
following calls to macb_tx no TX buffers are released -> the
netif_queue was stopped, and never woken up again.

The solution is to disable the transmitter, if TGO is set, before
clening up after the underrun, and re-enable the transmitter when the
cleaning up is done.
Signed-off-by: Richard Röjfors <richard.rojfors@endian.se>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Updating the version and the year of updated files
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To make sure no swapping are made by the compiler, changed HAS_WORK to inline
functions and added all the necessary barriers
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Driver supports the 57711 and 57711E as well but the description was out of
date
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the default PHY version (0x4321) is read - the PHY FW load failed
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10M/100M autoneg was not establishing link.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Setting loopback requires time to take effect
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The HW should be configured so fast toggling between 1G and 10G will not be
missed. Make sure that the HW is re-configured in full
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the page size is > 8KB this violation happens
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Don't dump eeprom when bnx2x adapter is down.  Running ethtool -e causes an eeh
without it when the device is down
Signed-off-by: Paul Larson <pl@linux.vnet.ibm.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Has a negative side effect when sending MAC update with no content (as done in
the self-test)
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The lock was release too soon. Make sure the HW is marked as locked until the
boot driver was unloaded from FW perspective
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Failures in the probe not handled correctly - separate the flow to handle

different failures
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Error check could result with not freeing the IRQ
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
  IB/ehca: Use consistent types for ehca_plpar_hcall9()
  IB/ehca: Fix printk format warnings from u64 type change
  IPoIB: Do not print error messages for multicast join retries
  IB/mlx4: Fix memory ordering problem when posting LSO sends
  mlx4_core: Fix min() warning
  IPoIB: Fix deadlock between ipoib_open() and child interface create
  IPoIB: Fix hang in napi_disable() if P_Key is never found

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6:
  move wm8400-regulator's probe function to .devinit.text

Reading 0 bytes from /sys/devices/platform/dell_rbu/image_type or
/sys/devices/platform/dell_rbu/packet_size by an ordinary user causes an
oops.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Plug this leak.
Acked-by: David Howells <dhowells@redhat.com>
Cc: James Morris <jmorris@namei.org>
Cc: <stable@kernel.org>
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

A pointer to wm8400_regulator_probe is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded.  Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.

An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

ehca_plpar_hcall9() takes an unsigned long array, so make all callers
pass that in.  This fixes warnings introduced by commit fe333321
("powerpc: Change u64/s64 to a long long integer type"), which changed
u64 from unsigned long to unsigned long long.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Commit fe333321 ("powerpc: Change u64/s64 to a long long integer
type") changed u64 from unsigned long to unsigned long long, which
means that printk formats for printing u64 values should use "ll"
instead of "l" to avoid warnings.  Fix all the places affected by this
in ehca.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

When IPoIB tries to join a multicast group, and the SA module's SM
address handle is NULL (because of an SM change, etc), the join
returns with -EAGAIN status.  In that case, don't print an error
message unless multicast debugging is enabled.
Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

The current work request posting code writes the LSO segment before
writing any data segments.  This leaves a window where the LSO segment
overwrites the stamping in one cacheline that the HCA prefetches
before the rest of the cacheline is filled with the correct data
segments.  When the HCA processes this work request, a local
protection error may result.

Fix this by saving the LSO header size field off and writing it only
after all data segments are written.  This fix is a cleaned-up version
of a patch from Jack Morgenstein <jackm@dev.mellanox.co.il>.

This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1383>.
Reported-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (23 commits)
  ACPI PCI hotplug: harden against panic regression
  ACPI: rename main.c to sleep.c
  dell-laptop: move to drivers/platform/x86/ from drivers/misc/
  eeepc-laptop: enable Bluetooth ACPI details
  ACPI: fix ACPI_FADT_S4_RTC_WAKE comment
  kprobes: check CONFIG_FREEZER instead of CONFIG_PM
  PM: Fix freezer compilation if PM_SLEEP is unset
  thermal fixup for broken BIOS which has invalid trip points.
  ACPI: EC: Don't trust ECDT tables from ASUS
  ACPI: EC: Limit workaround for ASUS notebooks even more
  ACPI: thinkpad-acpi: bump up version to 0.22
  ACPI: thinkpad-acpi: handle HKEY event 6030
  ACPI: thinkpad-acpi: clean-up fan subdriver quirk
  ACPI: thinkpad-acpi: start the event hunt season
  ACPI: thinkpad-acpi: handle HKEY thermal and battery alarms
  ACPI: thinkpad-acpi: clean up hotkey_notify()
  ACPI: thinkpad-acpi: use killable instead of interruptible mutexes
  ACPI: thinkpad-acpi: add UWB radio support
  ACPI: thinkpad-acpi: preserve radio state across shutdown
  ACPI: thinkpad-acpi: resume with radios disabled
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  netxen: include ipv6.h (fixes build failure)
  netxen: avoid invalid iounmap

ACPI hotplug panic with current git head
http://lkml.org/lkml/2009/1/10/136

Rather than reverting the entire commit that causes the crash:
e8c331e9
"PCI hotplug: introduce functions for ACPI slot detection"

simply harden against it while the changes to
the hotplug code on this particularl machine are understood.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Len Brown <len.brown@intel.com>