- 21 Mar, 2016 28 commits
-
-
Mikulas Patocka authored
commit d531be2c upstream. I have a ST4000DM000 disk. If Linux is booted while the disk is spun down, the command that sets transfer mode causes the disk to spin up. The spin-up takes longer than the default 5s timeout, so the command fails and timeout is reported. Fix this by increasing the timeout to 15s, which is enough for the disk to spin up. Signed-off-by:
Mikulas Patocka <mpatocka@redhat.com> Signed-off-by:
Tejun Heo <tj@kernel.org> Signed-off-by:
Zefan Li <lizefan@huawei.com>
-
Arne Fitzenreiter authored
commit cda57b1b upstream. This device loses blocks, often the partition table area, on trim. Disable TRIM. http://pcengines.ch/msata16a.htmSigned-off-by:
Arne Fitzenreiter <arne_f@ipfire.org> Signed-off-by:
-
Arne Fitzenreiter authored
commit 71d126fd upstream. Some devices lose data on TRIM whether queued or not. This patch adds a horkage to disable TRIM. tj: Collapsed unnecessary if() nesting. Signed-off-by:
-
Aleksei Mamlin authored
commit 08c85d2a upstream. Enabling AA on HP 250GB SATA disk VB0250EAVER causes errors: [ 3.788362] ata3.00: failed to enable AA (error_mask=0x1) [ 3.789243] ata3.00: failed to enable AA (error_mask=0x1) Add the ATA_HORKAGE_BROKEN_FPDMA_AA for this specific harddisk. tj: Collected FPDMA_AA entries and updated comment. Signed-off-by:
Aleksei Mamlin <mamlinav@gmail.com> Signed-off-by:
-
Lior Amsalem authored
commit 945b4744 upstream. This commit adds the necessary quirk to make the Marvell 4140 SATA PMP work properly. This PMP doesn't like SRST on port number 4 (the host port) so this commit marks this port as not supporting SRST. Signed-off-by:
Lior Amsalem <alior@marvell.com> Reviewed-by:
Nadav Haklai <nadavh@marvell.com> Signed-off-by:
Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by:
-
Seymour, Shane M authored
commit e7ac6c66 upstream. Two SLES11 SP3 servers encountered similar crashes simultaneously following some kind of SAN/tape target issue: ... qla2xxx [0000:81:00.0]-801c:3: Abort command issued nexus=3:0:2 -- 1 2002. qla2xxx [0000:81:00.0]-801c:3: Abort command issued nexus=3:0:2 -- 1 2002. qla2xxx [0000:81:00.0]-8009:3: DEVICE RESET ISSUED nexus=3:0:2 cmd=ffff882f89c2c7c0. qla2xxx [0000:81:00.0]-800c:3: do_reset failed for cmd=ffff882f89c2c7c0. qla2xxx [0000:81:00.0]-800f:3: DEVICE RESET FAILED: Task management failed nexus=3:0:2 cmd=ffff882f89c2c7c0. qla2xxx [0000:81:00.0]-8009:3: TARGET RESET ISSUED nexus=3:0:2 cmd=ffff882f89c2c7c0. qla2xxx [0000:81:00.0]-800c:3: do_reset failed for cmd=ffff882f89c2c7c0. qla2xxx [0000:81:00.0]-800f:3: TARGET RESET FAILED: Task management failed nexus=3:0:2 cmd=ffff882f89c2c7c0. qla2xxx [0000:81:00.0]-8012:3: BUS RESET ISSUED nexus=3:0:2. qla2xxx [0000:81:00.0]-802b:3: BUS RESET SUCCEEDED nexus=3:0:2. qla2xxx [0000:81:00.0]-505f:3: Link is operational (8 Gbps). qla2xxx [0000:81:00.0]-8018:3: ADAPTER RESET ISSUED nexus=3:0:2. qla2xxx [0000:81:00.0]-00af:3: Performing ISP error recovery - ha=ffff88bf04d18000. rport-3:0-0: blocked FC remote port time out: removing target and saving binding qla2xxx [0000:81:00.0]-505f:3: Link is operational (8 Gbps). qla2xxx [0000:81:00.0]-8017:3: ADAPTER RESET SUCCEEDED nexus=3:0:2. rport-2:0-0: blocked FC remote port time out: removing target and saving binding sg_rq_end_io: device detached BUG: unable to handle kernel NULL pointer dereference at 00000000000002a8 IP: [<ffffffff8133b268>] __pm_runtime_idle+0x28/0x90 PGD 7e6586f067 PUD 7e5af06067 PMD 0 [1739975.390354] Oops: 0002 [#1] SMP CPU 0 ... Supported: No, Proprietary modules are loaded [1739975.390463] Pid: 27965, comm: ABCD Tainted: PF X 3.0.101-0.29-default #1 HP ProLiant DL580 Gen8 RIP: 0010:[<ffffffff8133b268>] [<ffffffff8133b268>] __pm_runtime_idle+0x28/0x90 RSP: 0018:ffff8839dc1e7c68 EFLAGS: 00010202 RAX: 0000000000000000 RBX: ffff883f0592fc00 RCX: 0000000000000090 RDX: 0000000000000000 RSI: 0000000000000004 RDI: 0000000000000138 RBP: 0000000000000138 R08: 0000000000000010 R09: ffffffff81bd39d0 R10: 00000000000009c0 R11: ffffffff81025790 R12: 0000000000000001 R13: ffff883022212b80 R14: 0000000000000004 R15: ffff883022212b80 FS: 00007f8e54560720(0000) GS:ffff88407f800000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b CR2: 00000000000002a8 CR3: 0000007e6ced6000 CR4: 00000000001407f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 Process ABCD (pid: 27965, threadinfo ffff8839dc1e6000, task ffff883592e0c640) Stack: ffff883f0592fc00 00000000fffffffa 0000000000000001 ffff883022212b80 ffff883eff772400 ffffffffa03fa309 0000000000000000 0000000000000000 ffffffffa04003a0 ffff883f063196c0 ffff887f0379a930 ffffffff8115ea1e Call Trace: [<ffffffffa03fa309>] st_open+0x129/0x240 [st] [<ffffffff8115ea1e>] chrdev_open+0x13e/0x200 [<ffffffff811588a8>] __dentry_open+0x198/0x310 [<ffffffff81167d74>] do_last+0x1f4/0x800 [<ffffffff81168fe9>] path_openat+0xd9/0x420 [<ffffffff8116946c>] do_filp_open+0x4c/0xc0 [<ffffffff8115a00f>] do_sys_open+0x17f/0x250 [<ffffffff81468d92>] system_call_fastpath+0x16/0x1b [<00007f8e4f617fd0>] 0x7f8e4f617fcf Code: eb d3 90 48 83 ec 28 40 f6 c6 04 48 89 6c 24 08 4c 89 74 24 20 48 89 fd 48 89 1c 24 4c 89 64 24 10 41 89 f6 4c 89 6c 24 18 74 11 <f0> ff 8f 70 01 00 00 0f 94 c0 45 31 ed 84 c0 74 2b 4c 8d a5 a0 RIP [<ffffffff8133b268>] __pm_runtime_idle+0x28/0x90 RSP <ffff8839dc1e7c68> CR2: 00000000000002a8 Analysis reveals the cause of the crash to be due to STp->device being NULL. The pointer was NULLed via scsi_tape_put(STp) when it calls scsi_tape_release(). In st_open() we jump to err_out after scsi_block_when_processing_errors() completes and returns the device as offline (sdev_state was SDEV_DEL): 1180 /* Open the device. Needs to take the BKL only because of incrementing the SCSI host 1181 module count. */ 1182 static int st_open(struct inode *inode, struct file *filp) 1183 { 1184 int i, retval = (-EIO); 1185 int resumed = 0; 1186 struct scsi_tape *STp; 1187 struct st_partstat *STps; 1188 int dev = TAPE_NR(inode); 1189 char *name; ... 1217 if (scsi_autopm_get_device(STp->device) < 0) { 1218 retval = -EIO; 1219 goto err_out; 1220 } 1221 resumed = 1; 1222 if (!scsi_block_when_processing_errors(STp->device)) { 1223 retval = (-ENXIO); 1224 goto err_out; 1225 } ... 1264 err_out: 1265 normalize_buffer(STp->buffer); 1266 spin_lock(&st_use_lock); 1267 STp->in_use = 0; 1268 spin_unlock(&st_use_lock); 1269 scsi_tape_put(STp); <-- STp->device = 0 after this 1270 if (resumed) 1271 scsi_autopm_put_device(STp->device); 1272 return retval; The ref count for the struct scsi_tape had already been reduced to 1 when the .remove method of the st module had been called. The kref_put() in scsi_tape_put() caused scsi_tape_release() to be called: 0266 static void scsi_tape_put(struct scsi_tape *STp) 0267 { 0268 struct scsi_device *sdev = STp->device; 0269 0270 mutex_lock(&st_ref_mutex); 0271 kref_put(&STp->kref, scsi_tape_release); <-- calls this 0272 scsi_device_put(sdev); 0273 mutex_unlock(&st_ref_mutex); 0274 } In scsi_tape_release() the struct scsi_device in the struct scsi_tape gets set to NULL: 4273 static void scsi_tape_release(struct kref *kref) 4274 { 4275 struct scsi_tape *tpnt = to_scsi_tape(kref); 4276 struct gendisk *disk = tpnt->disk; 4277 4278 tpnt->device = NULL; <<<---- where the dev is nulled 4279 4280 if (tpnt->buffer) { 4281 normalize_buffer(tpnt->buffer); 4282 kfree(tpnt->buffer->reserved_pages); 4283 kfree(tpnt->buffer); 4284 } 4285 4286 disk->private_data = NULL; 4287 put_disk(disk); 4288 kfree(tpnt); 4289 return; 4290 } Although the problem was reported on SLES11.3 the problem appears in linux-next as well. The crash is fixed by reordering the code so we no longer access the struct scsi_tape after the kref_put() is done on it in st_open(). Signed-off-by:
Shane Seymour <shane.seymour@hp.com> Signed-off-by:
Darren Lavender <darren.lavender@hp.com> Reviewed-by:
Johannes Thumshirn <jthumshirn@suse.com> Acked-by:
Kai Mäkisara <kai.makisara@kolumbus.fi> Signed-off-by:
James Bottomley <JBottomley@Odin.com> Signed-off-by:
-
Wengang Wang authored
commit 4fabb594 upstream. Fixes: 3e0249f9 ("RDS/IB: add refcount tracking to struct rds_ib_device") There lacks a dropping on rds_ib_device.refcount in case rds_ib_alloc_fmr failed(mr pool running out). this lead to the refcount overflow. A complain in line 117(see following) is seen. From vmcore: s_ib_rdma_mr_pool_depleted is 2147485544 and rds_ibdev->refcount is -2147475448. That is the evidence the mr pool is used up. so rds_ib_alloc_fmr is very likely to return ERR_PTR(-EAGAIN). 115 void rds_ib_dev_put(struct rds_ib_device *rds_ibdev) 116 { 117 BUG_ON(atomic_read(&rds_ibdev->refcount) <= 0); 118 if (atomic_dec_and_test(&rds_ibdev->refcount)) 119 queue_work(rds_wq, &rds_ibdev->free_work); 120 } fix is to drop refcount when rds_ib_alloc_fmr failed. Signed-off-by:
Wengang Wang <wen.gang.wang@oracle.com> Reviewed-by:
Haggai Eran <haggaie@mellanox.com> Signed-off-by:
Doug Ledford <dledford@redhat.com> Signed-off-by:
-
Heiko Carstens authored
commit e47994dd upstream. The sfpc inline assembly within execve_tail() may incorrectly set bits 28-31 of the sfpc instruction to a value which is not zero. These bits however are currently unused and therefore should be zero so we won't get surprised if these bits will be used in the future. Therefore remove the second operand from the inline assembly. Signed-off-by:
Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by:
Martin Schwidefsky <schwidefsky@de.ibm.com> [lizf: Backported to 3.4: adjust context] Signed-off-by:
-
Julian Anastasov authored
commit 2c17d27c upstream. Incoming packet should be either in backlog queue or in RCU read-side section. Otherwise, the final sequence of flush_backlog() and synchronize_net() may miss packets that can run without device reference: CPU 1 CPU 2 skb->dev: no reference process_backlog:__skb_dequeue process_backlog:local_irq_enable on_each_cpu for flush_backlog => IPI(hardirq): flush_backlog - packet not found in backlog CPU delayed ... synchronize_net - no ongoing RCU read-side sections netdev_run_todo, rcu_barrier: no ongoing callbacks __netif_receive_skb_core:rcu_read_lock - too late free dev process packet for freed dev Fixes: 6e583ce5 ("net: eliminate refcounting in backlog queue") Cc: Eric W. Biederman <ebiederm@xmission.com> Cc: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by:
Julian Anastasov <ja@ssi.bg> Signed-off-by:
David S. Miller <davem@davemloft.net> [lizf: Backported to 3.4: - adjust context - no need to change "goto unlock" to "goto out"] Signed-off-by:
-
Julian Anastasov authored
commit e9e4dd32 upstream. commit 381c759d ("ipv4: Avoid crashing in ip_error") fixes a problem where processed packet comes from device with destroyed inetdev (dev->ip_ptr). This is not expected because inetdev_destroy is called in NETDEV_UNREGISTER phase and packets should not be processed after dev_close_many() and synchronize_net(). Above fix is still required because inetdev_destroy can be called for other reasons. But it shows the real problem: backlog can keep packets for long time and they do not hold reference to device. Such packets are then delivered to upper levels at the same time when device is unregistered. Calling flush_backlog after NETDEV_UNREGISTER_FINAL still accounts all packets from backlog but before that some packets continue to be delivered to upper levels long after the synchronize_net call which is supposed to wait the last ones. Also, as Eric pointed out, processed packets, mostly from other devices, can continue to add new packets to backlog. Fix the problem by moving flush_backlog early, after the device driver is stopped and before the synchronize_net() call. Then use netif_running check to make sure we do not add more packets to backlog. We have to do it in enqueue_to_backlog context when the local IRQ is disabled. As result, after the flush_backlog and synchronize_net sequence all packets should be accounted. Thanks to Eric W. Biederman for the test script and his valuable feedback! Reported-by:
Vittorio Gambaletta <linuxbugs@vittgam.net> Fixes: 6e583ce5 ("net: eliminate refcounting in backlog queue") Cc: Eric W. Biederman <ebiederm@xmission.com> Cc: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by:
-
Daniel Borkmann authored
commit 4f7d2cdf upstream. Jason Gunthorpe reported that since commit c02db8c6 ("rtnetlink: make SR-IOV VF interface symmetric"), we don't verify IFLA_VF_INFO attributes anymore with respect to their policy, that is, ifla_vfinfo_policy[]. Before, they were part of ifla_policy[], but they have been nested since placed under IFLA_VFINFO_LIST, that contains the attribute IFLA_VF_INFO, which is another nested attribute for the actual VF attributes such as IFLA_VF_MAC, IFLA_VF_VLAN, etc. Despite the policy being split out from ifla_policy[] in this commit, it's never applied anywhere. nla_for_each_nested() only does basic nla_ok() testing for struct nlattr, but it doesn't know about the data context and their requirements. Fix, on top of Jason's initial work, does 1) parsing of the attributes with the right policy, and 2) using the resulting parsed attribute table from 1) instead of the nla_for_each_nested() loop (just like we used to do when still part of ifla_policy[]). Reference: http://thread.gmane.org/gmane.linux.network/368913 Fixes: c02db8c6 ("rtnetlink: make SR-IOV VF interface symmetric") Reported-by:
Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Cc: Chris Wright <chrisw@sous-sol.org> Cc: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com> Cc: Greg Rose <gregory.v.rose@intel.com> Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Cc: Rony Efraim <ronye@mellanox.com> Cc: Vlad Zolotarov <vladz@cloudius-systems.com> Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com> Cc: Thomas Graf <tgraf@suug.ch> Signed-off-by:
Daniel Borkmann <daniel@iogearbox.net> Acked-by:
Vlad Zolotarov <vladz@cloudius-systems.com> Signed-off-by:
Ben Hutchings <ben@decadent.org.uk> Signed-off-by:
-
Zhao Junwang authored
commit 01447e9f upstream. legacy setcrtc ioctl does take a 32 bit value which might indeed overflow the checks of crtc_req->x > INT_MAX and crtc_req->y > INT_MAX aren't needed any more with this v2: -polish the annotation according to Daniel's comment Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by:
Zhao Junwang <zhjwpku@gmail.com> Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by:
-
Martin Schwidefsky authored
commit f9c87a6f upstream. If the kernel is compiled with gcc 5.1 and the XZ compression option the decompress_kernel function calls _sclp_print_early in 64-bit mode while the content of the upper register half of %r6 is non-zero. This causes a specification exception on the servc instruction in _sclp_servc. The _sclp_print_early function saves and restores the upper registers halves but it fails to clear them for the 31-bit code of the mini sclp driver. Signed-off-by:
-
Joe Thornber authored
commit 1c751879 upstream. Allocate memory using GFP_NOIO when deleting a btree. dm_btree_del() can be called via an ioctl and we don't want to recurse into the FS or block layer. Signed-off-by:
Joe Thornber <ejt@redhat.com> Signed-off-by:
Mike Snitzer <snitzer@redhat.com> Signed-off-by:
-
Peter Sanford authored
commit f98a7aa8 upstream. Add the USB serial console device ID for Aruba Networks 7xxx series controllers which have a USB port for their serial console. Signed-off-by:
Peter Sanford <peter@sanford.io> Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Claudio Cappelli authored
commit f6d7fb37 upstream. Add device Olivetti Olicard 300 (Network Connect: MT6225) - IDs 2020:4000. T: Bus=01 Lev=02 Prnt=04 Port=00 Cnt=01 Dev#= 10 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=2020 ProdID=4000 Rev=03.00 S: Manufacturer=Network Connect S: Product=MT6225 C: #Ifs= 7 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=02 Prot=01 Driver=option I: If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 6 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage Signed-off-by:
Claudio Cappelli <claudio.cappelli.linux@gmail.com> Suggested-by:
Lars Melin <larsm17@gmail.com> [johan: amend commit message with devices info ] Signed-off-by:
-
Joe Thornber authored
commit a822c83e upstream. Given the pool's cell_sort_array holds 8192 pointers it triggers an order 5 allocation via kmalloc. This order 5 allocation is prone to failure as system memory gets more fragmented over time. Fix this by allocating the cell_sort_array using vmalloc. Signed-off-by:
-
Dennis Yang authored
commit 4c7e3093 upstream. redistribute3() shares entries out across 3 nodes. Some entries were being moved the wrong way, breaking the ordering. This manifested as a BUG() in dm-btree-remove.c:shift() when entries were removed from the btree. For additional context see: https://www.redhat.com/archives/dm-devel/2015-May/msg00113.htmlSigned-off-by:
Dennis Yang <shinrairis@gmail.com> Signed-off-by:
-
Dominic Sacré authored
commit 0689a86a upstream. The Steinberg MI2 and MI4 interfaces are compatible with the USB class audio spec, but the MIDI part of the devices is reported as a vendor specific interface. This patch adds entries to quirks-table.h to recognize the MIDI endpoints. Audio functionality was already working and is unaffected by this change. Signed-off-by:
Dominic Sacré <dominic.sacre@gmx.de> Signed-off-by:
Albert Huitsing <albert@huitsing.nl> Acked-by:
Clemens Ladisch <clemens@ladisch.de> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Al Viro authored
commit 0a73d0a2 upstream. Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
Joe Perches authored
commit a28e4b2b upstream. Removing unnecessary static buffers is good. Use the vsprintf %pV extension instead. Signed-off-by:
Joe Perches <joe@perches.com> Signed-off-by:
Mikulas Patocka <mikulas@twibright.com> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> [Mikulas: - The bug corrected by the patch is - if hpfs_error is called concurrently on multiple filesystems, it could corrupt the string because the text buffer is shared. That's why I marked the patch for stable.] [lizf: Backported to 3.4: adjust context] Signed-off-by:
-
Sanidhya Kashyap authored
commit ce657611 upstream. There is a possibility of nothing being allocated to the new_opts in case of memory pressure, therefore return ENOMEM for such case. Signed-off-by:
Sanidhya Kashyap <sanidhya.gatech@gmail.com> Signed-off-by:
-
Kirill A. Shutemov authored
commit 6b7339f4 upstream. Reading page fault handler code I've noticed that under right circumstances kernel would map anonymous pages into file mappings: if the VMA doesn't have vm_ops->fault() and the VMA wasn't fully populated on ->mmap(), kernel would handle page fault to not populated pte with do_anonymous_page(). Let's change page fault handler to use do_anonymous_page() only on anonymous VMA (->vm_ops == NULL) and make sure that the VMA is not shared. For file mappings without vm_ops->fault() or shred VMA without vm_ops, page fault on pte_none() entry would lead to SIGBUS. Signed-off-by:
Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Acked-by:
Oleg Nesterov <oleg@redhat.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Willy Tarreau <w@1wt.eu> Signed-off-by:
-
Michal Hocko authored
commit 7444a072 upstream. ext4_free_blocks is looping around the allocation request and mimics __GFP_NOFAIL behavior without any allocation fallback strategy. Let's remove the open coded loop and replace it with __GFP_NOFAIL. Without the flag the allocator has no way to find out never-fail requirement and cannot help in any way. Signed-off-by:
Michal Hocko <mhocko@suse.cz> Signed-off-by:
Theodore Ts'o <tytso@mit.edu> Signed-off-by:
-
Nikolay Borisov authored
commit c45653c3 upstream. Switch ext4 to using sb_getblk_gfp with GFP_NOFS added to fix possible deadlocks in the page writeback path. Signed-off-by:
Nikolay Borisov <kernel@kyup.com> Signed-off-by:
-
Nikolay Borisov authored
commit bd7ade3c upstream. sb_getblk() is used during ext4 (and possibly other FSes) writeback paths. Sometimes such path require allocating memory and guaranteeing that such allocation won't block. Currently, however, there is no way to provide user flags for sb_getblk which could lead to deadlocks. This patch implements a sb_getblk_gfp with the only difference it can accept user-provided GFP flags. Signed-off-by:
-
Gioh Kim authored
commit 3b5e6454 upstream. A buffer cache is allocated from movable area because it is referred for a while and released soon. But some filesystems are taking buffer cache for a long time and it can disturb page migration. New APIs are introduced to allocate buffer cache with user specific flag. *_gfp APIs are for user want to set page allocation flag for page cache allocation. And *_unmovable APIs are for the user wants to allocate page cache from non-movable area. Signed-off-by:
Gioh Kim <gioh.kim@lge.com> Signed-off-by:
Jan Kara <jack@suse.cz> [lizf: Backported to 3.4: adjust context] Signed-off-by:
-
Filipe Manana authored
commit c3f4a168 upstream. The free space entries are allocated using kmem_cache_zalloc(), through __btrfs_add_free_space(), therefore we should use kmem_cache_free() and not kfree() to avoid any confusion and any potential problem. Looking at the kfree() definition at mm/slab.c it has the following comment: /* * (...) * * Don't free memory not originally allocated by kmalloc() * or you will run into trouble. */ So better be safe and use kmem_cache_free(). Signed-off-by:
Filipe Manana <fdmanana@suse.com> Reviewed-by:
David Sterba <dsterba@suse.cz> Signed-off-by:
Chris Mason <clm@fb.com> Signed-off-by:
-
- 22 Oct, 2015 12 commits
-
-
Zefan Li authored
-
Olga Kornievskaia authored
commit a41cbe86 upstream. A test case is as the description says: open(foobar, O_WRONLY); sleep() --> reboot the server close(foobar) The bug is because in nfs4state.c in nfs4_reclaim_open_state() a few line before going to restart, there is clear_bit(NFS4CLNT_RECLAIM_NOGRACE, &state->flags). NFS4CLNT_RECLAIM_NOGRACE is a flag for the client states not open owner states. Value of NFS4CLNT_RECLAIM_NOGRACE is 4 which is the value of NFS_O_WRONLY_STATE in nfs4_state->flags. So clearing it wipes out state and when we go to close it, “call_close” doesn’t get set as state flag is not set and CLOSE doesn’t go on the wire. Signed-off-by:
Olga Kornievskaia <aglo@umich.edu> Signed-off-by:
Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by:
-
Eric W. Biederman authored
commit 397d425d upstream. In rare cases a directory can be renamed out from under a bind mount. In those cases without special handling it becomes possible to walk up the directory tree to the root dentry of the filesystem and down from the root dentry to every other file or directory on the filesystem. Like division by zero .. from an unconnected path can not be given a useful semantic as there is no predicting at which path component the code will realize it is unconnected. We certainly can not match the current behavior as the current behavior is a security hole. Therefore when encounting .. when following an unconnected path return -ENOENT. - Add a function path_connected to verify path->dentry is reachable from path->mnt.mnt_root. AKA to validate that rename did not do something nasty to the bind mount. To avoid races path_connected must be called after following a path component to it's next path component. Signed-off-by:
"Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by:
-
Eric W. Biederman authored
commit cde93be4 upstream. A rename can result in a dentry that by walking up d_parent will never reach it's mnt_root. For lack of a better term I call this an escaped path. prepend_path is called by four different functions __d_path, d_absolute_path, d_path, and getcwd. __d_path only wants to see paths are connected to the root it passes in. So __d_path needs prepend_path to return an error. d_absolute_path similarly wants to see paths that are connected to some root. Escaped paths are not connected to any mnt_root so d_absolute_path needs prepend_path to return an error greater than 1. So escaped paths will be treated like paths on lazily unmounted mounts. getcwd needs to prepend "(unreachable)" so getcwd also needs prepend_path to return an error. d_path is the interesting hold out. d_path just wants to print something, and does not care about the weird cases. Which raises the question what should be printed? Given that <escaped_path>/<anything> should result in -ENOENT I believe it is desirable for escaped paths to be printed as empty paths. As there are not really any meaninful path components when considered from the perspective of a mount tree. So tweak prepend_path to return an empty path with an new error code of 3 when it encounters an escaped path. Signed-off-by:
-
Mike Marciniszyn authored
commit d6f1c17e upstream. The lkey table is allocated with with a get_user_pages() with an order based on a number of index bits from a module parameter. The underlying kernel code cannot allocate that many contiguous pages. There is no reason the underlying memory needs to be physically contiguous. This patch: - switches the allocation/deallocation to vmalloc/vfree - caps the number of bits to 23 to insure at least 1 generation bit o this matches the module parameter description Reviewed-by:
Vinit Agnihotri <vinit.abhay.agnihotri@intel.com> Signed-off-by:
Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by:
-
Jan Kara authored
commit 841df7df upstream. Commit 6f6a6fda "jbd2: fix ocfs2 corrupt when updating journal superblock fails" changed jbd2_cleanup_journal_tail() to return EIO when the journal is aborted. That makes logic in jbd2_log_do_checkpoint() bail out which is fine, except that jbd2_journal_destroy() expects jbd2_log_do_checkpoint() to always make a progress in cleaning the journal. Without it jbd2_journal_destroy() just loops in an infinite loop. Fix jbd2_journal_destroy() to cleanup journal checkpoint lists of jbd2_log_do_checkpoint() fails with error. Reported-by:
Eryu Guan <guaneryu@gmail.com> Tested-by:
Jan Kara <jack@suse.com> Signed-off-by:
-
John Youn authored
commit aebda618 upstream. This fixes an issue introduced in commit b23c8439 (usb: dwc3: gadget: fix DEPSTARTCFG for non-EP0 EPs) that made sure we would only use DEPSTARTCFG once per SetConfig. The trick is that we should use one DEPSTARTCFG per SetConfig *OR* SetInterface. SetInterface was completely missed from the original patch. This problem became aparent after commit 76e838c9 (usb: dwc3: gadget: return error if command sent to DEPCMD register fails) added checking of the return status of device endpoint commands. 'Set Endpoint Transfer Resource' command was caught failing occasionally. This is because the Transfer Resource Index was not getting reset during a SET_INTERFACE request. Finally, to fix the issue, was we have to do is make sure that our start_config_issued flag gets reset whenever we receive a SetInterface request. To verify the problem (and its fix), all we have to do is run test 9 from testusb with 'testusb -t 9 -s 2048 -a -c 5000'. Tested-by:
Huang Rui <ray.huang@amd.com> Tested-by:
Subbaraya Sundeep Bhatta <subbaraya.sundeep.bhatta@xilinx.com> Fixes: b23c8439 (usb: dwc3: gadget: fix DEPSTARTCFG for non-EP0 EPs) Signed-off-by:
John Youn <johnyoun@synopsys.com> Signed-off-by:
Felipe Balbi <balbi@ti.com> [lizf: Backported to 3.4: use dev_vdbg() instead of dwc3_trace()] Signed-off-by:
-
Zefan Li authored
Reported-by:
Jim Faulkner <jfaulkne@ccs.neu.edu> Fixed-by:
Nicolas Schichan <nschichan@freebox.fr> Signed-off-by:
-
Zefan Li authored
Signed-off-by: -
Christian König authored
commit 7c0411d2 upstream. We have that bug for years and some users report side effects when fixing it on older hardware. So revert it for VM_CONTEXT0_PAGE_TABLE_END_ADDR, but keep it for VM 1-15. Signed-off-by:
Christian König <christian.koenig@amd.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> [lizf: Backported to 3.4: drop the change to clk.c] Signed-off-by:
-
Zefan Li authored
This reverts commit 961bd135. Both Satoshi-san and Cal reported a kernel crash due to this commit. Reported-by:
Satoshi Iwamoto <satoshi.iwamoto@nifty.ne.jp> Reported-by:
Cal Peake <cp@absolutedigital.net> Signed-off-by:
-
Jani Nikula authored
commit 245ec9d8 upstream. This reverts commit 0aedb162. I messed things up while applying [1] to drm-intel-fixes. Rectify. [1] http://mid.gmane.org/1432827156-9605-1-git-send-email-ville.syrjala@linux.intel.com Fixes: 0aedb162 ("drm/i915: Don't skip request retirement if the active list is empty") Acked-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by:
Jani Nikula <jani.nikula@intel.com> [lizf: Backported to 3.4: adjust context] Signed-off-by:
-
