wait_for_completion_timeout() never returns negative value.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

From 'clock-frequency' device tree property, configure I2C SCL
frequency by calculating the timing register values according to
input clock.

After soft reset in reinit function, the timing registers are set
to default values (configured in design tool). So, setting SCL
frequency is done inside reinit function after the soft reset.
This allows configuration of SCL frequency exclusively through
software via device tree property, overriding the design.
If the clock-frequency parameter is not specified in DT, driver
doesn't configure frequency, making it backward compatible.
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Signed-off-by: Manikanta Guntupalli <manikanta.guntupalli@amd.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Xilinx AXI I2C IP is updated with a bug fix for dynamic mode reads.
Older IPs are handled with a workaround in which they are using
xiic standard mode for all these effected use cases.
Add the new IP version to compatible.
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Signed-off-by: Manikanta Guntupalli <manikanta.guntupalli@amd.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Add xilinx I2C new version 'xlnx,axi-iic-2.1' string to compatible.
Add clock-frequency as optional property.
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Signed-off-by: Manikanta Guntupalli <manikanta.guntupalli@amd.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Avoid code duplication by calling i801_check_post() from i801_access().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

This avoids code duplication, in a next step we'll call
i801_check_post() from i801_transaction() as well.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Similar to what was done for non-block commands, centralize block
command register settings in i801_block_transaction().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Currently configuring command register settings is distributed over multiple
functions. At first centralize this for non-block commands in
i801_simple_transaction().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Currently we touch SMBAUXCTL even if not needed. That's the case for block
commands that don't use block buffer mode, either because block buffer
mode isn't available or because it's not supported for the respective
command (e.g. I2C block transfer). Improve this by setting/resetting
SMBAUXCTL_E32B in i801_block_transaction_by_block() only.

Small downside is that we now access SMBAUXCTL twice for transactions
that use PEC and block buffer mode. But this should a rather rare case
and the impact is negligible.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Factor out non-block pre/post processing to a new function
i801_simple_transaction(), complementing existing function
i801_block_transaction(). This makes i801_access() better readable.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Correct spelling problems for Documentation/i2c/ as reported
by codespell.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Convert i2c-st.txt into st,sti-i2c.yaml for the i2c-st driver.
Signed-off-by: Alain Volmat <avolmat@me.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Factor out setting SMBHSTADD to a helper. The current code makes the
assumption that constant I2C_SMBUS_READ has bit 0 set, that's not ideal.
Therefore let the new helper explicitly check for I2C_SMBUS_READ.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

According to the datasheet the block process call requires block
buffer mode. The user may disable block buffer mode by module
parameter disable_features, in such a case we have to clear
FEATURE_BLOCK_PROC.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Host notification uses an interrupt, therefore it makes sense only if
interrupts are enabled. Make this dependency explicit by removing
FEATURE_HOST_NOTIFY if FEATURE_IRQ isn't set.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Not sure if it can happen, but better play safe: If SMBHSTSTS_BYTE_DONE
and an error flag is set, then don't trust the result and skip calling
i801_isr_byte_done(). In addition clear status bit SMBHSTSTS_BYTE_DONE
in the main interrupt handler, this allows to simplify the code a
little.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Rely on pm_sleep_ptr when setting the pm ops and get rid
of the ifdef CONFIG_PM_SLEEP around suspend/resume functions.
Signed-off-by: Alain Volmat <avolmat@me.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

UniPhier I2C controller allows reset control support.
Add resets property to the controller as optional.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Add myself as maintainer of the Loongson LS2X I2C driver.
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

'DYNAMIC_MODE_READ_BROKEN_BIT' quirk added in the driver,
effected IP versions no longer enter dynamic mode.
So, remove local_irq_save/local_irq_restore APIs from driver.
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Signed-off-by: Manikanta Guntupalli <manikanta.guntupalli@amd.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

smbus_block_read is added to xiic driver to read from few sensors
which support this command. Since the number of bytes to read is not
known prior to transfer, xiic standard mode is being used for low level
control of IP.
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Signed-off-by: Manikanta Guntupalli <manikanta.guntupalli@amd.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

If the tx_half_empty interrupt comes first instead of tx_empty,
STOP bit is generated even before all the bytes are transmitted
out on the bus.
STOP bit should be sent only after all the bytes in the FIFO are
transmitted out of the FIFO. So wait until FIFO is empty before sending
the STOP bit.
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Signed-off-by: Manikanta Guntupalli <manikanta.guntupalli@amd.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Xilinx I2C IP has two modes of operation, both of which implement
I2C transactions. The only difference from sw perspective is the
programming sequence for these modes.
Dynamic mode  -> Simple to program, less number of steps in sequence.
Standard mode -> Gives flexibility, more number of steps in sequence.

In dynamic mode, during the i2c-read transactions, if there is a
delay(> 200us) between the register writes (address & byte count),
read transaction fails. On a system with load, this scenario is
occurring frequently.
To avoid this, switch to standard mode if there is a read request.

Added a quirk to identify the IP version effected by this and follow
the standard mode.
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Signed-off-by: Manikanta Guntupalli <manikanta.guntupalli@amd.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

repeated start

When a combined message request comes from user space, the
controller has to initiate repeated start sequence. In standard
mode, this repeated start sequence is corrupted if there is still
data in the Tx FIFO.

So, always make sure that all the bytes are completely transmitted
out of the FIFO by waiting for TXEMPTY, if the previous message is
of Tx type.
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Signed-off-by: Manikanta Guntupalli <manikanta.guntupalli@amd.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

read transfers

Added standard mode for AXI I2C controller to enable read transfers
of size more than 255 bytes. The driver selects standard mode in the
following scenarios.

1. If a single message request comes from user space, requesting a
read of more than 255 bytes

2. If a message set request comes from user space consisting of many
messages and if any one of them is a read operation, irrespective
of the size of transfer. (This is done because it is observed that
repeated start operation is not happening in dynamic mode read as
expected in a message set request from user space.)
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Signed-off-by: Manikanta Guntupalli <manikanta.guntupalli@amd.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

This I2C module is integrated into the Loongson-2K SoCs and Loongson
LS7A bridge chip.
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Add Loongson LS2X I2C controller binding with DT schema format using
json-schema.
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

regmap_read() API signature expects the caller to send "unsigned int"
type to return back the read value, but there are some occurrences of 'u32'
across i2c-designware-* files.

Change them to match the regmap_read() signature.
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

On some AMD platforms, based on the new designware datasheet,
BIOS sets the BIT(11) within the IC_CON register to advertise
the "bus clear feature capability".

AMD/Designware datasheet says:

Bit(11) BUS_CLEAR_FEATURE_CTRL. Read-write,Volatile. Reset: 0.
Description: In Master mode:
- 1'b1: Bus Clear Feature is enabled.
- 1'b0: Bus Clear Feature is Disabled.
In Slave mode, this register bit is not applicable.

On AMD platform designs:
1. BIOS programs the BUS_CLEAR_FEATURE_CTRL and enables the detection
of SCL/SDA stuck low.
2. Whenever the stuck low is detected, the SMU FW shall do the bus
recovery procedure.

Currently, the way in which the "master_cfg" is built in the driver, it
overrides the BUS_CLEAR_FEATURE_CTRL advertised by BIOS and the SMU FW
cannot initiate the bus recovery if the stuck low is detected.

Hence add a check in i2c_dw_probe_master() that if the BIOS
advertises the bus clear feature, let driver not ignore it and
adapt accordingly.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

There are slave devices that understand I2C but have read-only SDA and
SCL. Examples are FD650 7-segment LED controller and its derivatives.
Typical board designs don't even have a pull-up for both pins.
Handle the new attributes for write-only SDA and missing pull-up on
SDA/SCL.

For either pin the open-drain and has-no-pullup properties are
mutually-exclusive, what is documented in the DT property documentation.
We don't add an extra warning here because the open-drain properties
are marked deprecated anyway.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
[wsa: switched to device properties]
Signed-off-by: Wolfram Sang <wsa@kernel.org>

This is in preparation of supporting write-only SDA in i2c-gpio.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

There are slave devices that understand I2C but have read-only SDA and
SCL. Examples are FD650 7-segment LED controller and its derivatives.
Typical board designs don't even have a pull-up for both pins.
Therefore add properties for not using open-drain. For write-only SCL
we have a property already, add one for write-only SDA.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Document the compatible for the CCI block found on SM6350 SoC.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Add support for the ACPI-based device registration, so that the driver
can be also enabled through ACPI table.
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Tested-by: Peibao Liu <liupeibao@loongson.cn>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

In the mrecv() function the Cadence I2C driver has the following expression
in an if clause.

	((id->p_msg->flags & I2C_M_RECV_LEN) != I2C_M_RECV_LEN) &&
	 (id->recv_count <= CDNS_I2C_FIFO_DEPTH))

Earlier in the same function when I2C_M_RECV_LEN is set the recv_count is
initialized to a value that is larger than CDNS_I2C_FIFO_DEPTH. This means
if the first expression is false the second expression is also false.
Checking the first expression is thus redundant and can be removed.

This slightly simplifies the logic.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

The irq field of the driver state struct is only used in the probe
function. There is no need to keep it around. Remove it from the state
struct and use a on-stack variable instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>