Commit 9ad18043 ("thermal: core: Send trip crossing notifications
at init time if needed") overlooked the case when a trip point that
has started as invalid is set to a valid temperature later.  Namely,
the initial threshold value for all trips is zero, so if a previously
invalid trip becomes valid and its (new) low temperature is above the
zone temperature, a spurious trip crossing notification will occur and
it may trigger the WARN_ON() in handle_thermal_trip().

To address this, set the initial threshold for all trips to INT_MAX.

There is also the case when a valid writable trip becomes invalid that
requires special handling.  First, in accordance with the change
mentioned above, the trip's threshold needs to be set to INT_MAX to
avoid the same issue.  Second, if the trip in question is passive and
it has been crossed by the thermal zone temperature on the way up, the
zone's passive count has been incremented and it is in the passive
polling mode, so its passive count needs to be adjusted to allow the
passive polling to be turned off eventually.

Fixes: 9ad18043 ("thermal: core: Send trip crossing notifications at init time if needed")
Fixes: 042a3d80 ("thermal: core: Move passive polling management to the core")
Reported-by: Zhang Rui <zhang.rui@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Wendy Wang <wendy.wang@intel.com>

Merge thermal driver fixes for 6.10-rc1 from Daniel Lezcano:

"- Check for a NULL pointer before using it in the probe routine of the
   Mediatek LVTS driver (Julien Panis)

 - Remove the num_lvts_sensor and cal_offset fields of the
   lvts_ctrl_data as they are not used. These are not functional fixes
   but slight memory usage fix of the Mediatek LVTS driver (Julien
   Panis)

 - Fix wrong lvts_ctrl index leading to a NULL pointer dereference in
   the Mediatek LVTS driver (Julien Panis)"

* tag 'thermal-v6.10-rc1-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/thermal/linux:
  thermal/drivers/mediatek/lvts_thermal: Fix wrong lvts_ctrl index
  thermal/drivers/mediatek/lvts_thermal: Remove unused members from struct lvts_ctrl_data
  thermal/drivers/mediatek/lvts_thermal: Check NULL ptr on lvts_data

Pull thermal control updates from Rafael Wysocki:
 "The most significant part of this is a rework of thermal governors,
  including a redesign of the thermal governor interface and changes to
  make some of them take trip point hysteresis into account properly, as
  well as some related cleanups of the thermal governors and thermal
  core.

  The above is based on preliminary changes refactoring thermal data
  structures and moving the definitions of some of them into the thermal
  core which also ensure that trip point crossing notifications will be
  sent to user space via netlink and recorded in the debug statistics in
  temperature order.

  In addition, netlink bind/unbind notifications are added to the
  thermal core and the Intel HFI driver is modified to use them to avoid
  sending netlink messages until there are subscribers.

  Apart from that, multiple thermal drivers are updated which includes
  new hardware support (MediaTek MT8188 and MT8186, Amlogic A1 thermal
  sensor, Loongson-2K2000, Lmh QCM2290), fixes, cleanups and
  documentation updates, and the recently added thermal debug code is
  fixed and cleaned up.

  Specifics:

   - Redesign the thermal governor interface to allow the governors to
     work in a more straightforward way (Rafael Wysocki)

   - Make thermal governors take the current trip point thresholds into
     account in their computations which allows trip hysteresis to be
     observed more accurately (Rafael Wysocki)

   - Make the thermal core manage passive polling for thermal zones and
     remove passive polling management from thermal governors (Rafael
     Wysocki)

   - Refactor trip point representation and move the definition of
     thermal governor and thermal zone device structures to the thermal
     core (Rafael Wysocki)

   - Sort trip point crossing notifications and debug recording of trip
     point crossing events by temperature (Rafael Wysocki)

   - Improve the handling of cooling device states and thermal
     mitigation episodes in progress in the thermal debug code (Rafael
     Wysocki)

   - Avoid excessive updates of trip point statistics and clean up the
     printing of thermal mitigation episode information (Rafael Wysocki)

   - Clean up thermal governors and thermal core (Rafael Wysocki)

   - Allow thermal drivers to register notifiers that will be invoked on
     netlink events like BIND and UNBIND, so that they can adjust their
     activity depending on whether or not there are any subscribers of
     netlink messages coming from them, and make the Intel HFI driver
     use this mechanism (Stanislaw Gruszka)

   - Adjust the update delay and capabilities-per-event values in the
     Intel HFI thermal driver to prevent it from missing events and
     allow it to process more data in one go (Ricardo Neri)

   - Add missing MODULE_DESCRIPTION() to multiple files in the
     int340x_thermal and intel_soc_dts_iosf drivers (Srinivas
     Pandruvada)

   - Replace deprecated strncpy() with strscpy() in the int340x_thermal
     driver (Justin Stitt)

   - Add QCM2290 compatible DT bindings for Lmh and fix a NULL pointer
     dereference in the lmh driver when the SCM is not present (Konrad
     Dybcio)

   - Use the strreplace() function instead of doing it manually in the
     Armada driver (Rasmus Villemoes)

   - Convert st,stih407-thermal to DT schema and fix up missing
     properties (Raphael Gallais-Pou)

   - Add suspend/resume by restoring the context of the tsens sensor
     (Priyansh Jain)

   - Support A1 SoC family Thermal Sensor controller and add the DT
     bindings (Dmitry Rokosov)

   - Improve the temperature approximation calculation and consolidate
     the Tj constant into a shared area of the structure instead of
     duplicating it on the Rcar Gen3 (Niklas Söderlund)

   - Fix the Mediatek LVTS sensor coefficient for the MT8192 in order to
     support it correctly (Hsin-Te Yuan)

   - Fix a NULL pointer dereference in the tsens driver when the
     function compute_intercept_slope() is called with a NULL parameter
     (Aleksandr Mishin)

   - Remove some unused fields in struct qpnp_tm_chip and k3_bandgap
     (Christophe Jaillet)

   - Fix up calibration efuse data decoding, consolidate the code by
     checking boundaries and refactor some part of the LVTS Mediatek
     driver. After setting the scene, add MT8186 and MT8188 along with
     the DT bindings (Nicolas Pitre)

   - Add Loongson-2K2000 support after some minor code adjustements and
     providing the DT bindings definition (Binbin Zhou)"

* tag 'thermal-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (72 commits)
  thermal: intel: hfi: Increase the number of CPU capabilities per netlink event
  thermal: intel: hfi: Rename HFI_MAX_THERM_NOTIFY_COUNT
  thermal: intel: hfi: Shorten the thermal netlink event delay to 100ms
  thermal: intel: hfi: Rename HFI_UPDATE_INTERVAL
  thermal: intel: Add missing module description
  thermal: core: Move passive polling management to the core
  thermal: core: Do not call handle_thermal_trip() if zone temperature is invalid
  thermal: trip: Add missing empty code line
  thermal/debugfs: Avoid printing zero duration for mitigation events in progress
  thermal/debugfs: Pass cooling device state to thermal_debug_cdev_add()
  thermal/debugfs: Create records for cdev states as they get used
  thermal: core: Introduce thermal_governor_trip_crossed()
  thermal/debugfs: Make tze_seq_show() skip invalid trips and trips with no stats
  thermal/debugfs: Rename thermal_debug_update_temp() to thermal_debug_update_trip_stats()
  thermal/debugfs: Clean up thermal_debug_update_temp()
  thermal/debugfs: Avoid excessive updates of trip point statistics
  thermal: core: Relocate critical and hot trip handling
  thermal: core: Drop the .throttle() governor callback
  thermal: gov_user_space: Use .trip_crossed() instead of .throttle()
  thermal: gov_fair_share: Eliminate unnecessary integer divisions
  ...

Merge tag 'linux_kselftest-next-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest

Pull kselftest updates from Shuah Khan:

 - make framework and tests reporting KTAP compliant

 - make ktap_helpers and power_supply test POSIX compliant

 - add ksft_exit_fail_perror() to include errono in string form

 - avoid clang reporting false positive static analysis errors about
   functions that exit and never return. ksft_exit* functions are marked
   __noreturn to address this problem

 - add mechanism for reporting a KSFT_ result code

 - fix build warnings related missing headers and unused variables

 - fix clang build failures

 - cleanups to resctrl test

 - add host arch for LLVM builds

* tag 'linux_kselftest-next-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest: (44 commits)
  selftests/sgx: Include KHDR_INCLUDES in Makefile
  selftests: Compile kselftest headers with -D_GNU_SOURCE
  selftests/resctrl: fix clang build warnings related to abs(), labs() calls
  selftests/ftrace: Fix checkbashisms errors
  selftests/ftrace: Fix BTFARG testcase to check fprobe is enabled correctly
  selftests/capabilities: fix warn_unused_result build warnings
  selftests: filesystems: add missing stddef header
  selftests: kselftest_deps: fix l5_test() empty variable
  selftests: default to host arch for LLVM builds
  selftests/resctrl: fix clang build failure: use LOCAL_HDRS
  selftests/binderfs: use the Makefile's rules, not Make's implicit rules
  Documentation: kselftest: fix codeblock
  selftests: kselftest: Make ksft_exit functions return void instead of int
  selftests: x86: ksft_exit_pass() does not return
  selftests: timers: ksft_exit functions do not return
  selftests: sync: ksft_exit_pass() does not return
  selftests/resctrl: ksft_exit_skip() does not return
  selftests: pidfd: ksft_exit functions do not return
  selftests/mm: ksft_exit functions do not return
  selftests: membarrier: ksft_exit_pass() does not return
  ...

Merge tag 'linux_kselftest-kunit-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest

Pull kunit updates from Shuah Khan:

 - fix race condition in try-catch completion

 - change __kunit_test_suites_init() to exit early if there is
   nothing to test

 - change string-stream-test to use KUNIT_DEFINE_ACTION_WRAPPER

 - move fault tests behind KUNIT_FAULT_TEST Kconfig option

 - kthread test fixes and improvements

 - iov_iter test fixes

* tag 'linux_kselftest-kunit-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
  kunit: bail out early in __kunit_test_suites_init() if there are no suites to test
  kunit: string-stream-test: use KUNIT_DEFINE_ACTION_WRAPPER
  kunit: test: Move fault tests behind KUNIT_FAULT_TEST Kconfig option
  kunit: unregister the device on error
  kunit: Fix race condition in try-catch completion
  kunit: Add tests for fault
  kunit: Print last test location on fault
  kunit: Fix KUNIT_SUCCESS() calls in iov_iter tests
  kunit: Handle test faults
  kunit: Fix timeout message
  kunit: Fix kthread reference
  kunit: Handle thread creation error

Merge tag 'linux_kselftest-nolibc-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest

Pull nolibc updates from Shuah Khan:

 - add support for uname(2)

 - remove open-coded strnlen()

 - export strlen()

 - add tests for strlcat() and strlcpy()

 - fix memory error in realloc()

 - fix strlcat() and strlcpy() return code and size usage

* tag 'linux_kselftest-nolibc-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
  tools/nolibc: add support for uname(2)
  tools/nolibc/string: remove open-coded strnlen()
  selftests/nolibc: Add tests for strlcat() and strlcpy()
  tools/nolibc: Fix strlcpy() return code and size usage
  tools/nolibc: Fix strlcat() return code and size usage
  tools/nolibc/string: export strlen()
  tools/nolibc/stdlib: fix memory error in realloc()

Pull OpenRISC updates from Stafford Horne:
 "A few cleanups and fixups from me:

   - Add a few missing relocations to fix module loading

   - Cleanup FPU state save and restore to be more efficient

   - Cleanups to traps handling and logging

   - Fix issue with poweroff being broken after recent power driver
     refactorings"

* tag 'for-linus' of https://github.com/openrisc/linux:
  openrisc: Move FPU state out of pt_regs
  openrisc: Add FPU config
  openrisc: traps: Don't send signals to kernel mode threads
  openrisc: traps: Remove calls to show_registers before die
  openrisc: traps: Convert printks to pr_<level> macros
  openrisc: Add support for more module relocations
  openrisc: Define openrisc relocation types
  openrisc: Use do_kernel_power_off()

Pull sh updates from John Paul Adrian Glaubitz:
 "The majority of improvements are coming from Geert Uytterhoeven who
  took the time to fix a total of 30 cases of "-Wmissing-prototypes"
  compiler warnings, either by adding a missing header include, defining
  the missing forward declarations or making the functions in question
  static.

  In the case of several DMA functions, the fix was to actually just
  remove them as they were added but never used. Another one of these
  warnings was eliminated by removing the left-over sh5 cache handling
  support, a change that was suggested by Yoshinori Sato and, finally,
  the last of these warnings was fixed by guarding the function
  setup_profiling_timer() with CONFIG_PROFILING.

  While at it, Geert also removed two unneeded casts to kprobe_opcode_t
  in the kprobes code.

  Another change was contributed by Guenter Roeck to fix errors that
  were reported during checksum unit tests. The fix actually reverts the
  older change cadc4e1a ("sh: Handle calling csum_partial with
  misaligned data") which turned to be incorrect. It remains to be
  investigated whether there is a better way to handle misaligned data
  in csum_partial().

  A small fix contributed by Krzysztof Kozlowski drops the incorrect SPI
  controller spi-max-frequency property in the device tree source file
  for the J2 device platform while Uwe Kleine-König converted the
  push-switch driver to have its callback function return void, a change
  that is currently being applied to all drivers throughout the kernel
  in order to avoid resource leaks.

  Last but not least, Artur Rojek has fixed the IOPORT base address for
  the Sega Dreamcast platform which allows the Linux kernel to be
  successfully booted on this once popular video game console for the
  first time since a long time ago"

* tag 'sh-for-v6.10-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/glaubitz/sh-linux: (35 commits)
  sh: setup: Add missing forward declaration for sh_fdt_init()
  sh: smp: Protect setup_profiling_timer() by CONFIG_PROFILING
  sh: of-generic: Add missing #include <asm/clock.h>
  sh: dreamcast: Fix GAPS PCI bridge addressing
  sh: boot: Add proper forward declarations
  sh: boot: Remove sh5 cache handling
  Revert "sh: Handle calling csum_partial with misaligned data"
  sh: j2: Drop incorrect SPI controller spi-max-frequency property
  sh: push-switch: Convert to platform remove callback returning void
  sh: sh7785lcr: Make init_sh7785lcr_IRQ() static
  sh: sh7757: Add missing #include <asm/mmzone.h>
  sh: sh7757lcr: Make init_sh7757lcr_IRQ() static
  sh: mach-sh03: Make sh03_rtc_settimeofday() static
  sh: mach-highlander: Add missing #include <mach/highlander.h>
  sh: traps: Make is_dsp_inst() static
  sh: cache: Move forward declarations to <asm/cacheflush.h>
  sh: dma: Remove unused functionality
  sh: dwarf: Make dwarf_lookup_fde() static
  sh: kprobes: Remove unneeded kprobe_opcode_t casts
  sh: kprobes: Make trampoline_probe_handler() static
  ...

Pull arm64 updates from Will Deacon:
 "The most interesting parts are probably the mm changes from Ryan which
  optimise the creation of the linear mapping at boot and (separately)
  implement write-protect support for userfaultfd.

  Outside of our usual directories, the Kbuild-related changes under
  scripts/ have been acked by Masahiro whilst the drivers/acpi/ parts
  have been acked by Rafael and the addition of cpumask_any_and_but()
  has been acked by Yury.

  ACPI:

   - Support for the Firmware ACPI Control Structure (FACS) signature
     feature which is used to reboot out of hibernation on some systems

  Kbuild:

   - Support for building Flat Image Tree (FIT) images, where the kernel
     Image is compressed alongside a set of devicetree blobs

  Memory management:

   - Optimisation of our early page-table manipulation for creation of
     the linear mapping

   - Support for userfaultfd write protection, which brings along some
     nice cleanups to our handling of invalid but present ptes

   - Extend our use of range TLBI invalidation at EL1

  Perf and PMUs:

   - Ensure that the 'pmu->parent' pointer is correctly initialised by
     PMU drivers

   - Avoid allocating 'cpumask_t' types on the stack in some PMU drivers

   - Fix parsing of the CPU PMU "version" field in assembly code, as it
     doesn't follow the usual architectural rules

   - Add best-effort unwinding support for USER_STACKTRACE

   - Minor driver fixes and cleanups

  Selftests:

   - Minor cleanups to the arm64 selftests (missing NULL check, unused
     variable)

  Miscellaneous:

   - Add a command-line alias for disabling 32-bit application support

   - Add part number for Neoverse-V2 CPUs

   - Minor fixes and cleanups"

* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (64 commits)
  arm64/mm: Fix pud_user_accessible_page() for PGTABLE_LEVELS <= 2
  arm64/mm: Add uffd write-protect support
  arm64/mm: Move PTE_PRESENT_INVALID to overlay PTE_NG
  arm64/mm: Remove PTE_PROT_NONE bit
  arm64/mm: generalize PMD_PRESENT_INVALID for all levels
  arm64: simplify arch_static_branch/_jump function
  arm64: Add USER_STACKTRACE support
  arm64: Add the arm64.no32bit_el0 command line option
  drivers/perf: hisi: hns3: Actually use devm_add_action_or_reset()
  drivers/perf: hisi: hns3: Fix out-of-bound access when valid event group
  drivers/perf: hisi_pcie: Fix out-of-bound access when valid event group
  kselftest: arm64: Add a null pointer check
  arm64: defer clearing DAIF.D
  arm64: assembler: update stale comment for disable_step_tsk
  arm64/sysreg: Update PIE permission encodings
  kselftest/arm64: Remove unused parameters in abi test
  perf/arm-spe: Assign parents for event_source device
  perf/arm-smmuv3: Assign parents for event_source device
  perf/arm-dsu: Assign parents for event_source device
  perf/arm-dmc620: Assign parents for event_source device
  ...

Pull m68k updates from Geert Uytterhoeven:

 - Fix invalid context sleep and reboot hang on Mac

 - Fix spinlock race in kernel thread creation

 - Miscellaneous fixes and improvements

 - defconfig updates

* tag 'm68k-for-v6.10-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
  m68k: defconfig: Update defconfigs for v6.9-rc1
  m68k: Move ARCH_HAS_CPU_CACHE_ALIASING
  m68k: mac: Fix reboot hang on Mac IIci
  m68k: Fix spinlock race in kernel thread creation
  m68k: Let GENERIC_IOMAP depend on HAS_IOPORT
  m68k: amiga: Use str_plural() to fix Coccinelle warning
  macintosh/via-macii: Fix "BUG: sleeping function called from invalid context"
  zorro: Use helpers from ioport.h
  m68k: Calculate THREAD_SIZE from THREAD_SIZE_ORDER

Pull x86 interrupt handling updates from Thomas Gleixner:
 "Add support for posted interrupts on bare metal.

  Posted interrupts is a virtualization feature which allows to inject
  interrupts directly into a guest without host interaction. The VT-d
  interrupt remapping hardware sets the bit which corresponds to the
  interrupt vector in a vector bitmap which is either used to inject the
  interrupt directly into the guest via a virtualized APIC or in case
  that the guest is scheduled out provides a host side notification
  interrupt which informs the host that an interrupt has been marked
  pending in the bitmap.

  This can be utilized on bare metal for scenarios where multiple
  devices, e.g. NVME storage, raise interrupts with a high frequency. In
  the default mode these interrupts are handles independently and
  therefore require a full roundtrip of interrupt entry/exit.

  Utilizing posted interrupts this roundtrip overhead can be avoided by
  coalescing these interrupt entries to a single entry for the posted
  interrupt notification. The notification interrupt then demultiplexes
  the pending bits in a memory based bitmap and invokes the
  corresponding device specific handlers.

  Depending on the usage scenario and device utilization throughput
  improvements between 10% and 130% have been measured.

  As this is only relevant for high end servers with multiple device
  queues per CPU attached and counterproductive for situations where
  interrupts are arriving at distinct times, the functionality is opt-in
  via a kernel command line parameter"

* tag 'x86-irq-2024-05-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/irq: Use existing helper for pending vector check
  iommu/vt-d: Enable posted mode for device MSIs
  iommu/vt-d: Make posted MSI an opt-in command line option
  x86/irq: Extend checks for pending vectors to posted interrupts
  x86/irq: Factor out common code for checking pending interrupts
  x86/irq: Install posted MSI notification handler
  x86/irq: Factor out handler invocation from common_interrupt()
  x86/irq: Set up per host CPU posted interrupt descriptors
  x86/irq: Reserve a per CPU IDT vector for posted MSIs
  x86/irq: Add a Kconfig option for posted MSI
  x86/irq: Remove bitfields in posted interrupt descriptor
  x86/irq: Unionize PID.PIR for 64bit access w/o casting
  KVM: VMX: Move posted interrupt descriptor out of VMX code

Pull interrupt subsystem updates from Thomas Gleixner:
 "Core code:

   - Interrupt storm detection for the lockup watchdog:

     Lockups which are caused by interrupt storms are not easy to debug
     because there is no information about the events which make the
     lockup detector trigger.

     To make this more user friendly, provide an extenstion to interrupt
     statistics which allows to take snapshots and an interface to
     retrieve the delta to the snapshot. Use this new mechanism in the
     watchdog code to do a two stage lockup analysis by taking the
     snapshot and printing the deltas for the topmost active interrupts
     on the second trigger.

     Note: This contains both the interrupt and the watchdog changes as
     the latter depend on the former obviously.

   - Avoid summation loops in the /proc/interrupts output and use the
     global counter when possible

   - Skip suspended interrupts on CPU hotplug operations to ensure that
     they are not delivered before the system resumes the device drivers
     when coming out of suspend.

   - On CPU hot-unplug interrupts which are affine to the outgoing CPU
     are migrated to a different CPU in the affinity mask. This can fail
     when the CPUs have no vectors left. Instead of giving up try to
     migrate it to any online CPU and thereby breaking the affinity
     setting in order to prevent a stale device interrupt which targets
     an offline CPU

   - The usual small cleanups

  Driver code:

   - Support for the RISCV AIA MSI controller

   - Make the interrupt allocation for the Loongson PCH controller more
     flexible to prevent vector exhaustion

   - The usual set of cleanups and fixes all over the place"

* tag 'irq-core-2024-05-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (51 commits)
  irqchip/gic-v3-its: Remove BUG_ON in its_vpe_irq_domain_alloc
  cpuidle: Avoid explicit cpumask allocation on stack
  irqchip/sifive-plic: Avoid explicit cpumask allocation on stack
  irqchip/riscv-aplic-direct: Avoid explicit cpumask allocation on stack
  irqchip/loongson-eiointc: Avoid explicit cpumask allocation on stack
  irqchip/gic-v3-its: Avoid explicit cpumask allocation on stack
  irqchip/irq-bcm6345-l1: Avoid explicit cpumask allocation on stack
  cpumask: Introduce cpumask_first_and_and()
  irqchip/irq-brcmstb-l2: Avoid saving mask on shutdown
  genirq: Reuse irq_is_nmi()
  genirq/cpuhotplug: Retry with cpu_online_mask when migration fails
  genirq/cpuhotplug: Skip suspended interrupts when restoring affinity
  arm64: dts: st: Add interrupt parent to pinctrl on stm32mp251
  arm64: dts: st: Add exti1 and exti2 nodes on stm32mp251
  ARM: dts: stm32: List exti parent interrupts on stm32mp131
  ARM: dts: stm32: List exti parent interrupts on stm32mp151
  arm64: Kconfig.platforms: Enable STM32_EXTI for ARCH_STM32
  irqchip/stm32-exti: Mark events reserved with RIF configuration check
  irqchip/stm32-exti: Skip secure events
  irqchip/stm32-exti: Convert driver to standard PM
  ...

Pull x86 timers update from Thomas Gleixner:
 "A single update for the TSC synchronixation sanity checks:

  The sad state of TSC being notoriously non-sychronized for several
  decades caused the kernel to grow quite rigorous sanity checks to
  detect whether the TSC is valid to be used for timekeeping.

  The TSC ADJUST MSR provides the offset between the initial TSC value
  after hardware reset and later modifications. This allows to detect
  cases where firmware tampers with the TSC and also allows to correct
  the firmware induced damage by resetting the offset in a controlled
  way.

  The universal correct rule is that the TSC ADJUST value has to be
  consistent within all CPUs of a socket.

  The kernel further assumes that the TSC offset should be consistent
  between sockets. That's not really correct as systems with a huge
  number of sockets are not architecurally guaranteed to reset the per
  socket TSC base synchronously.

  In case that the per socket offset is not consistent the kernel resets
  it to the offset of the boot CPU and then does a synchronization check
  which corrects for the inter socket delays.

  That works most of the time, but it is suboptimal as the firmware has
  eventually better information about the per socket offset and on sane
  systems that offset should just work in the validation checks"

* tag 'x86-timers-2024-05-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/tsc: Trust initial offset in architectural TSC-adjust MSRs

Pull timers and timekeeping updates from Thomas Gleixner:
 "Core code:

   - Make timekeeping and VDSO time readouts resilent against math
     overflow:

     In guest context the kernel is prone to math overflow when the host
     defers the timer interrupt due to overload, malfunction or malice.

     This can be mitigated by checking the clocksource delta for the
     maximum deferrement which is readily available. If that value is
     exceeded then the code uses a slowpath function which can handle
     the multiplication overflow.

     This functionality is enabled unconditionally in the kernel, but
     made conditional in the VDSO code. The latter is conditional
     because it allows architectures to optimize the check so it is not
     causing performance regressions.

     On X86 this is achieved by reworking the existing check for
     negative TSC deltas as a negative delta obviously exceeds the
     maximum deferrement when it is evaluated as an unsigned value. That
     avoids two conditionals in the hotpath and allows to hide both the
     negative delta and the large delta handling in the same slow path.

   - Add an initial minimal ktime_t abstraction for Rust

   - The usual boring cleanups and enhancements

  Drivers:

   - Boring updates to device trees and trivial enhancements in various
     drivers"

* tag 'timers-core-2024-05-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (33 commits)
  clocksource/drivers/arm_arch_timer: Mark hisi_161010101_oem_info const
  clocksource/drivers/timer-ti-dm: Remove an unused field in struct dmtimer
  clocksource/drivers/renesas-ostm: Avoid reprobe after successful early probe
  clocksource/drivers/renesas-ostm: Allow OSTM driver to reprobe for RZ/V2H(P) SoC
  dt-bindings: timer: renesas: ostm: Document Renesas RZ/V2H(P) SoC
  rust: time: doc: Add missing C header links
  clocksource: Make the int help prompt unit readable in ncurses
  hrtimer: Rename __hrtimer_hres_active() to hrtimer_hres_active()
  timerqueue: Remove never used function timerqueue_node_expires()
  rust: time: Add Ktime
  vdso: Fix powerpc build U64_MAX undeclared error
  clockevents: Convert s[n]printf() to sysfs_emit()
  clocksource: Convert s[n]printf() to sysfs_emit()
  clocksource: Make watchdog and suspend-timing multiplication overflow safe
  timekeeping: Let timekeeping_cycles_to_ns() handle both under and overflow
  timekeeping: Make delta calculation overflow safe
  timekeeping: Prepare timekeeping_cycles_to_ns() for overflow safety
  timekeeping: Fold in timekeeping_delta_to_ns()
  timekeeping: Consolidate timekeeping helpers
  timekeeping: Refactor timekeeping helpers
  ...

Pull x86 APIC update from Dave Hansen:
 "Coccinelle complained about some 64-bit divisions, but the divisor was
  really just a 32-bit value being stored as 'unsigned long'.

  Fixing the types fixes the warning"

* tag 'x86_apic_for_6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/apic: Improve data types to fix Coccinelle warnings

Pull x86 SEV updates from Borislav Petkov:

 - Small cleanups and improvements

* tag 'x86_sev_for_v6.10_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/sev: Make the VMPL0 checking more straight forward
  x86/sev: Rename snp_init() in boot/compressed/sev.c
  x86/sev: Shorten struct name snp_secrets_page_layout to snp_secrets_page

Pull x86 microcode loader updates from Borislav Petkov:

 - Fix a clang-15 build warning and other cleanups

* tag 'x86_microcode_for_v6.10_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/microcode: Remove unused struct cpu_info_ctx
  x86/microcode/AMD: Remove unused PATCH_MAX_SIZE macro
  x86/microcode/AMD: Avoid -Wformat warning with clang-15

Pull x86 resource control updates from Borislav Petkov:

 - Add a tracepoint to read out LLC occupancy of resource monitor IDs
   with the goal of freeing them sooner rather than later

 - Other code improvements and cleanups

* tag 'x86_cache_for_v6.10_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/resctrl: Add tracepoint for llc_occupancy tracking
  x86/resctrl: Rename pseudo_lock_event.h to trace.h
  x86/resctrl: Simplify call convention for MSR update functions
  x86/resctrl: Pass domain to target CPU

Pull x86 asm alternatives updates from Borislav Petkov:

 - Switch the in-place instruction patching which lead to at least one
   weird bug with 32-bit guests, seeing stale instruction bytes, to one
   working on a buffer, like the rest of the alternatives code does

 - Add a long overdue check to the X86_FEATURE flag modifying functions
   to warn when former get changed in a non-compatible way after
   alternatives have been patched because those changes will be already
   wrong

 - Other cleanups

* tag 'x86_alternatives_for_v6.10_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/alternatives: Remove alternative_input_2()
  x86/alternatives: Sort local vars in apply_alternatives()
  x86/alternatives: Optimize optimize_nops()
  x86/alternatives: Get rid of __optimize_nops()
  x86/alternatives: Use a temporary buffer when optimizing NOPs
  x86/alternatives: Catch late X86_FEATURE modifiers

Pull RAS update from Borislav Petkov:

 - Change the fixed-size buffer for MCE records to a dynamically sized
   one based on the number of CPUs present in the system

* tag 'ras_core_for_v6.10_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/mce: Dynamically size space for machine check records

Pull EDAC updates from Borislav Petkov:

 - Have skx_edac decode error addresses belonging to SGX properly

 - Remove a bunch of unused struct members

 - Other cleanups

* tag 'edac_updates_for_v6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras:
  EDAC/skx_common: Allow decoding of SGX addresses
  EDAC/mc_sysfs: Convert sprintf()/snprintf() to sysfs_emit()
  EDAC: Remove unused struct members
  EDAC: Remove dynamic attributes from edac_device_alloc_ctl_info()
  EDAC/device: Remove edac_dev_sysfs_block_attribute::store()
  EDAC/device: Remove edac_dev_sysfs_block_attribute::{block,value}
  EDAC/amd64: Remove unused struct member amd64_pvt::ext_nbcfg

Pull DSA and IAA accelerator mis-alignment fix from Arjan van de Ven:
 "The DSA (memory copy/zero/etc) and IAA (compression) accelerators in
  the Sapphire Rapids and Emerald Rapids SOCs turn out to have a bug
  that has security implications.

  Both of these accelerators work by the application submitting a 64
  byte command to the device; this command contains an opcode as well as
  the virtual address of the return value that the device will update on
  completion... and a set of opcode specific values.

  In a typical scenario a ring 3 application mmaps the device file and
  uses the ENQCMD or MOVDIR64 instructions (which are variations of a 64
  byte atomic write) on this mmap'd memory region to directly submit
  commands to a device hardware.

  The return value as specified in the command, is supposed to be 32 (or
  64) bytes aligned in memory, and generally the hardware checks and
  enforces this alignment.

  However in testing it has been found that there are conditions
  (controlled by the submitter) where this enforcement does not
  happen... which makes it possible for the return value to span a page
  boundary. And this is where it goes wrong - the accelerators will
  perform the virtual to physical address lookup on the first of the two
  pages, but end up continue writing to the next consecutive physical
  (host) page rather than the consecutive virtual page. In addition, the
  device will end up in a hung state on such unaligned write of the
  return value.

  This patch series has the proposed software side solution consisting
  of three parts:

   - Don't allow these two PCI devices to be assigned to VM guests (we
     cannot trust a VM guest to behave correctly and not cause this
     condition)

   - Don't allow ring 3 applications to set up the mmap unless they have
     CAP_SYS_RAWIO permissions. This makes it no longer possible for
     non-root applications to directly submit commands to the
     accelerator

   - Add a write() method to the device so that an application can
     submit its commands to the kernel driver, which performs the needed
     sanity checks before submitting it to the hardware.

  This switch from mmap to write is an incompatible interface change to
  non-root userspace, but we have not found a way to avoid this. All
  software we know of uses a small set of accessor libraries for these
  accelerators, for which libqpl and libdml (on github) are the most
  common. As part of the security release, updated versions of these
  libraries will be released that transparently fall back to write().

  Intel has assigned CVE-2024-21823 to this hardware issue"

* tag 'idxd-for-linus-may2024' of git bundle from Arjan:
  dmaengine: idxd: add a write() method for applications to submit work
  dmaengine: idxd: add a new security check to deal with a hardware erratum
  VFIO: Add the SPR_DSA and SPR_IAX devices to the denylist

Pull x86 shadow stacks from Ingo Molnar:
 "Enable shadow stacks for x32.

  While we normally don't do such feature-enabling for 32-bit anymore,
  this change is small, straightforward & tested on upstream glibc"

* tag 'x86-shstk-2024-05-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/shstk: Enable shadow stacks for x32

Pull x86 platform updates from Ingo Molnar:

 - Improve the DeviceTree (OF) NUMA enumeration code to address
   kernel warnings & mis-mappings on DeviceTree platforms

 - Migrate x86 platform drivers to the .remove_new callback API

 - Misc cleanups & fixes

* tag 'x86-platform-2024-05-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/platform/olpc-xo1-sci: Convert to platform remove callback returning void
  x86/platform/olpc-x01-pm: Convert to platform remove callback returning void
  x86/platform/iris: Convert to platform remove callback returning void
  x86/of: Change x86_dtb_parse_smp_config() to static
  x86/of: Map NUMA node to CPUs as per DeviceTree
  x86/of: Set the parse_smp_cfg for all the DeviceTree platforms by default
  x86/hyperv/vtl: Correct x86_init.mpparse.parse_smp_cfg assignment

Pull x86 percpu updates from Ingo Molnar:

 - Expand the named address spaces optimizations down to
   GCC 9.1+.

 - Re-enable named address spaces with sanitizers for GCC 13.3+

 - Generate better this_percpu_xchg_op() code

 - Introduce raw_cpu_read_long() to reduce ifdeffery

 - Simplify the x86_this_cpu_test_bit() et al macros

 - Address Sparse warnings

 - Misc cleanups & fixes

* tag 'x86-percpu-2024-05-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/percpu: Introduce raw_cpu_read_long() to reduce ifdeffery
  x86/percpu: Rewrite x86_this_cpu_test_bit() and friends as macros
  x86/percpu: Fix x86_this_cpu_variable_test_bit() asm template
  x86/percpu: Re-enable named address spaces with sanitizers for GCC 13.3+
  x86/percpu: Use __force to cast from __percpu address space
  x86/percpu: Do not use this_cpu_read_stable_8() for 32-bit targets
  x86/percpu: Unify arch_raw_cpu_ptr() defines
  x86/percpu: Enable named address spaces for GCC 9.1+
  x86/percpu: Re-enable named address spaces with KASAN for GCC 13.3+
  x86/percpu: Move raw_percpu_xchg_op() to a better place
  x86/percpu: Convert this_percpu_xchg_op() from asm() to C code, to generate better code

Pull x86 mm updates from Ingo Molnar:

 - Fix W^X violation check false-positives in the CPA code
   when running as a Xen PV guest

 - Fix W^X violation warning false-positives in show_fault_oops()

* tag 'x86-mm-2024-05-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/pat: Fix W^X violation false-positives when running as Xen PV guest
  x86/pat: Restructure _lookup_address_cpa()
  x86/mm: Use lookup_address_in_pgd_attr() in show_fault_oops()
  x86/pat: Introduce lookup_address_in_pgd_attr()

Pull x86 fpu updates from Ingo Molnar:

 - Fix asm() constraints & modifiers in restore_fpregs_from_fpstate()

 - Update comments

 - Robustify the free_vm86() definition

* tag 'x86-fpu-2024-05-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/fpu: Update fpu_swap_kvm_fpu() uses in comments as well
  x86/vm86: Make sure the free_vm86(task) definition uses its parameter even in the !CONFIG_VM86 case
  x86/fpu: Fix AMD X86_BUG_FXSAVE_LEAK fixup

Pull x86 entry cleanup from Ingo Molnar:

 - Merge thunk_64.S and thunk_32.S into thunk.S

* tag 'x86-entry-2024-05-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/entry: Merge thunk_64.S and thunk_32.S into thunk.S

Pull x86 cpu updates from Ingo Molnar:

 - Rework the x86 CPU vendor/family/model code: introduce the 'VFM'
   value that is an 8+8+8 bit concatenation of the vendor/family/model
   value, and add macros that work on VFM values. This simplifies the
   addition of new Intel models & families, and simplifies existing
   enumeration & quirk code.

 - Add support for the AMD 0x80000026 leaf, to better parse topology
   information

 - Optimize the NUMA allocation layout of more per-CPU data structures

 - Improve the workaround for AMD erratum 1386

 - Clear TME from /proc/cpuinfo as well, when disabled by the firmware

 - Improve x86 self-tests

 - Extend the mce_record tracepoint with the ::ppin and ::microcode fields

 - Implement recovery for MCE errors in TDX/SEAM non-root mode

 - Misc cleanups and fixes

* tag 'x86-cpu-2024-05-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (34 commits)
  x86/mm: Switch to new Intel CPU model defines
  x86/tsc_msr: Switch to new Intel CPU model defines
  x86/tsc: Switch to new Intel CPU model defines
  x86/cpu: Switch to new Intel CPU model defines
  x86/resctrl: Switch to new Intel CPU model defines
  x86/microcode/intel: Switch to new Intel CPU model defines
  x86/mce: Switch to new Intel CPU model defines
  x86/cpu: Switch to new Intel CPU model defines
  x86/cpu/intel_epb: Switch to new Intel CPU model defines
  x86/aperfmperf: Switch to new Intel CPU model defines
  x86/apic: Switch to new Intel CPU model defines
  perf/x86/msr: Switch to new Intel CPU model defines
  perf/x86/intel/uncore: Switch to new Intel CPU model defines
  perf/x86/intel/pt: Switch to new Intel CPU model defines
  perf/x86/lbr: Switch to new Intel CPU model defines
  perf/x86/intel/cstate: Switch to new Intel CPU model defines
  x86/bugs: Switch to new Intel CPU model defines
  x86/bugs: Switch to new Intel CPU model defines
  x86/cpu/vfm: Update arch/x86/include/asm/intel-family.h
  x86/cpu/vfm: Add new macros to work with (vendor/family/model) values
  ...

Pull x86 cleanups from Ingo Molnar:

 - Fix function prototypes to address clang function type cast
   warnings in the math-emu code

 - Reorder definitions in <asm/msr-index.h>

 - Remove unused code

 - Fix typos

 - Simplify #include sections

* tag 'x86-cleanups-2024-05-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/pci/ce4100: Remove unused 'struct sim_reg_op'
  x86/msr: Move ARCH_CAP_XAPIC_DISABLE bit definition to its rightful place
  x86/math-emu: Fix function cast warnings
  x86/extable: Remove unused fixup type EX_TYPE_COPY
  x86/rtc: Remove unused intel-mid.h
  x86/32: Remove unused IA32_STACK_TOP and two externs
  x86/head: Simplify relative include path to xen-head.S
  x86/fred: Fix typo in Kconfig description
  x86/syscall/compat: Remove ia32_unistd.h
  x86/syscall/compat: Remove unused macro __SYSCALL_ia32_NR
  x86/virt/tdx: Remove duplicate include
  x86/xen: Remove duplicate #include

Pull x86 build updates from Ingo Molnar:

 - Use -fpic to build the kexec 'purgatory' (the self-contained
   code that runs between two kernels)

 - Clean up vmlinux.lds.S generation

 - Simplify the X86_EXTENDED_PLATFORM section of the x86 Kconfig

 - Misc cleanups & fixes

* tag 'x86-build-2024-05-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/Kconfig: Merge the two CONFIG_X86_EXTENDED_PLATFORM entries
  x86/purgatory: Switch to the position-independent small code model
  x86/boot: Replace __PHYSICAL_START with LOAD_PHYSICAL_ADDR
  x86/vmlinux.lds.S: Take __START_KERNEL out conditional definition
  x86/vmlinux.lds.S: Remove conditional definition of LOAD_OFFSET
  vmlinux.lds.h: Fix a typo in comment

Pull x86 oops message cleanup from Ingo Molnar:

 - Use uniform "Oops: " prefix for die() messages

* tag 'x86-bugs-2024-05-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/dumpstack: Use uniform "Oops: " prefix for die() messages

Pull x86 boot updates from Ingo Molnar:

 - Move the kernel cmdline setup earlier in the boot process (again),
   to address a split_lock_detect= boot parameter bug

 - Ignore relocations in .notes sections

 - Simplify boot stack setup

 - Re-introduce a bootloader quirk wrt CR4 handling

 - Miscellaneous cleanups & fixes

* tag 'x86-boot-2024-05-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/boot/64: Clear most of CR4 in startup_64(), except PAE, MCE and LA57
  x86/boot: Move kernel cmdline setup earlier in the boot process (again)
  x86/build: Clean up arch/x86/tools/relocs.c a bit
  x86/boot: Ignore relocations in .notes sections in walk_relocs() too
  x86: Rename __{start,end}_init_task to __{start,end}_init_stack
  x86/boot: Simplify boot stack setup

Pull x86 asm updates from Ingo Molnar:

 - Clean up & fix asm() operand modifiers & constraints

 - Misc cleanups

* tag 'x86-asm-2024-05-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/alternatives: Remove a superfluous newline in _static_cpu_has()
  x86/asm/64: Clean up memset16(), memset32(), memset64() assembly constraints in <asm/string_64.h>
  x86/asm: Use "m" operand constraint in WRUSSQ asm template
  x86/asm: Use %a instead of %P operand modifier in asm templates
  x86/asm: Use %c/%n instead of %P operand modifier in asm templates
  x86/asm: Remove %P operand modifier from altinstr asm templates

Pull tip tree documentation update from Ingo Molnar:

 - Update the -tip maintainers merge policy document wrt
   merge window timing

* tag 'x86-misc-2024-05-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  Documentation/maintainer-tip: Clarify merge window policy

Pull scheduler updates from Ingo Molnar:

 - Add cpufreq pressure feedback for the scheduler

 - Rework misfit load-balancing wrt affinity restrictions

 - Clean up and simplify the code around ::overutilized and
   ::overload access.

 - Simplify sched_balance_newidle()

 - Bump SCHEDSTAT_VERSION to 16 due to a cleanup of CPU_MAX_IDLE_TYPES
   handling that changed the output.

 - Rework & clean up <asm/vtime.h> interactions wrt arch_vtime_task_switch()

 - Reorganize, clean up and unify most of the higher level
   scheduler balancing function names around the sched_balance_*()
   prefix

 - Simplify the balancing flag code (sched_balance_running)

 - Miscellaneous cleanups & fixes

* tag 'sched-core-2024-05-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (50 commits)
  sched/pelt: Remove shift of thermal clock
  sched/cpufreq: Rename arch_update_thermal_pressure() => arch_update_hw_pressure()
  thermal/cpufreq: Remove arch_update_thermal_pressure()
  sched/cpufreq: Take cpufreq feedback into account
  cpufreq: Add a cpufreq pressure feedback for the scheduler
  sched/fair: Fix update of rd->sg_overutilized
  sched/vtime: Do not include <asm/vtime.h> header
  s390/irq,nmi: Include <asm/vtime.h> header directly
  s390/vtime: Remove unused __ARCH_HAS_VTIME_TASK_SWITCH leftover
  sched/vtime: Get rid of generic vtime_task_switch() implementation
  sched/vtime: Remove confusing arch_vtime_task_switch() declaration
  sched/balancing: Simplify the sg_status bitmask and use separate ->overloaded and ->overutilized flags
  sched/fair: Rename set_rd_overutilized_status() to set_rd_overutilized()
  sched/fair: Rename SG_OVERLOAD to SG_OVERLOADED
  sched/fair: Rename {set|get}_rd_overload() to {set|get}_rd_overloaded()
  sched/fair: Rename root_domain::overload to ::overloaded
  sched/fair: Use helper functions to access root_domain::overload
  sched/fair: Check root_domain::overload value before update
  sched/fair: Combine EAS check with root_domain::overutilized access
  sched/fair: Simplify the continue_balancing logic in sched_balance_newidle()
  ...

Pull perf events updates from Ingo Molnar:

 - Combine perf and BPF for fast evalution of HW breakpoint
   conditions

 - Add LBR capture support outside of hardware events

 - Trigger IO signals for watermark_wakeup

 - Add RAPL support for Intel Arrow Lake and Lunar Lake

 - Optimize frequency-throttling

 - Miscellaneous cleanups & fixes

* tag 'perf-core-2024-05-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (21 commits)
  perf/bpf: Mark perf_event_set_bpf_handler() and perf_event_free_bpf_handler() as inline too
  selftests/perf_events: Test FASYNC with watermark wakeups
  perf/ring_buffer: Trigger IO signals for watermark_wakeup
  perf: Move perf_event_fasync() to perf_event.h
  perf/bpf: Change the !CONFIG_BPF_SYSCALL stubs to static inlines
  selftest/bpf: Test a perf BPF program that suppresses side effects
  perf/bpf: Allow a BPF program to suppress all sample side effects
  perf/bpf: Remove unneeded uses_default_overflow_handler()
  perf/bpf: Call BPF handler directly, not through overflow machinery
  perf/bpf: Remove #ifdef CONFIG_BPF_SYSCALL from struct perf_event members
  perf/bpf: Create bpf_overflow_handler() stub for !CONFIG_BPF_SYSCALL
  perf/bpf: Reorder bpf_overflow_handler() ahead of __perf_event_overflow()
  perf/x86/rapl: Add support for Intel Lunar Lake
  perf/x86/rapl: Add support for Intel Arrow Lake
  perf/core: Reduce PMU access to adjust sample freq
  perf/core: Optimize perf_adjust_freq_unthr_context()
  perf/x86/amd: Don't reject non-sampling events with configured LBR
  perf/x86/amd: Support capturing LBR from software events
  perf/x86/amd: Avoid taking branches before disabling LBR
  perf/x86/amd: Ensure amd_pmu_core_disable_all() is always inlined
  ...

Pull locking updates from Ingo Molnar:

 - Over a dozen code generation micro-optimizations for the atomic
   and spinlock code

 - Add more __ro_after_init attributes

 - Robustify the lockdevent_*() macros

* tag 'locking-core-2024-05-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  locking/pvqspinlock/x86: Use _Q_LOCKED_VAL in PV_UNLOCK_ASM macro
  locking/qspinlock/x86: Micro-optimize virt_spin_lock()
  locking/atomic/x86: Merge __arch{,_try}_cmpxchg64_emu_local() with __arch{,_try}_cmpxchg64_emu()
  locking/atomic/x86: Introduce arch_try_cmpxchg64_local()
  locking/pvqspinlock/x86: Remove redundant CMP after CMPXCHG in __raw_callee_save___pv_queued_spin_unlock()
  locking/pvqspinlock: Use try_cmpxchg() in qspinlock_paravirt.h
  locking/pvqspinlock: Use try_cmpxchg_acquire() in trylock_clear_pending()
  locking/qspinlock: Use atomic_try_cmpxchg_relaxed() in xchg_tail()
  locking/atomic/x86: Define arch_atomic_sub() family using arch_atomic_add() functions
  locking/atomic/x86: Rewrite x86_32 arch_atomic64_{,fetch}_{and,or,xor}() functions
  locking/atomic/x86: Introduce arch_atomic64_read_nonatomic() to x86_32
  locking/atomic/x86: Introduce arch_atomic64_try_cmpxchg() to x86_32
  locking/atomic/x86: Introduce arch_try_cmpxchg64() for !CONFIG_X86_CMPXCHG64
  locking/atomic/x86: Modernize x86_32 arch_{,try_}_cmpxchg64{,_local}()
  locking/atomic/x86: Correct the definition of __arch_try_cmpxchg128()
  x86/tsc: Make __use_tsc __ro_after_init
  x86/kvm: Make kvm_async_pf_enabled __ro_after_init
  context_tracking: Make context_tracking_key __ro_after_init
  jump_label,module: Don't alloc static_key_mod for __ro_after_init keys
  locking/qspinlock: Always evaluate lockevent* non-event parameter once

Merge tag 'tag-chrome-platform-firmware-for-v6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux

Pull chrome platform firmware updates from Tzung-Bi Shih:

 - Set driver owner in the core registration so that coreboot drivers
   don't need to set it individually

* tag 'tag-chrome-platform-firmware-for-v6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux:
  firmware: google: cbmem: drop driver owner initialization
  firmware: coreboot: store owner from modules with coreboot_driver_register()

Merge tag 'tag-chrome-platform-for-v6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux

Pull chrome platform updates from Tzung-Bi Shih:
 "New:
   - Support Framework Laptop 13 and 16 (AMD Ryzen)

  Improvements:
   - Use sysfs_emit() instead of sprintf() for sysfs' show()

  Fixes:
   - Fix flex-array-member-not-at-end compiler warnings by using
     DEFINE_RAW_FLEX()
   - Add HAS_IOPORT dependencies
   - Fix long pending events during suspend after resume

  Misc cleanups:
   - Provide ID tables for avoiding fallback match
   - Replace deprecated UNIVERSAL_DEV_PM_OPS()"

* tag 'tag-chrome-platform-for-v6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux: (22 commits)
  platform/chrome: cros_ec: Handle events during suspend after resume completion
  platform/chrome: cros_ec_lpc: add quirks for the Framework Laptop (AMD)
  platform/chrome: cros_ec_lpc: add a "quirks" system
  platform/chrome: cros_ec_lpc: pass driver_data from DMI to the device
  platform/chrome: cros_ec_lpc: introduce a priv struct for the lpc device
  platform/chrome: add HAS_IOPORT dependencies
  platform/chrome: cros_hps_i2c: Replace deprecated UNIVERSAL_DEV_PM_OPS()
  platform/chrome: cros_kbd_led_backlight: provide ID table for avoiding fallback match
  platform/chrome: wilco_ec: core: provide ID table for avoiding fallback match
  platform/chrome: wilco_ec: event: remove redundant MODULE_ALIAS
  platform/chrome: wilco_ec: debugfs: provide ID table for avoiding fallback match
  platform/chrome: wilco_ec: telemetry: provide ID table for avoiding fallback match
  platform/chrome: cros_ec_vbc: provide ID table for avoiding fallback match
  platform/chrome: cros_ec_lightbar: provide ID table for avoiding fallback match
  platform/chrome: cros_ec_sysfs: provide ID table for avoiding fallback match
  platform/chrome: cros_ec_debugfs: provide ID table for avoiding fallback match
  platform/chrome: cros_ec_chardev: provide ID table for avoiding fallback match
  platform/chrome: cros_usbpd_notify: provide ID table for avoiding fallback match
  platform/chrome: cros_usbpd_logger: provide ID table for avoiding fallback match
  platform/chrome: cros_ec_sensorhub: provide ID table for avoiding fallback match
  ...