- 15 Jun, 2020 3 commits
-
-
Sowmiya Sree Elavalagan authored
Removed reo cmd lock and unlock which was acquiring the lock immediately after unlock. Done for code clean up. Signed-off-by:
Sowmiya Sree Elavalagan <ssreeela@codeaurora.org> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1591713432-26426-1-git-send-email-ssreeela@codeaurora.org
-
Karthikeyan Periyasamy authored
spectral scan control interface is exposed through debugfs eentry. Relayfs is used to collect the spectral data. These interfaces are similar to ath10k spectral. spectral debugfs interfaces are below, echo background > /sys/kernel/debug/ieee80211/phy0/ath11k/spectral_scan_ctl echo trigger > /sys/kernel/debug/ieee80211/phy0/ath11k/spectral_scan_ctl iw dev wlan0 scan echo disable > /sys/kernel/debug/ieee80211/phy0/ath11k/spectral_scan_ctl cat /sys/kernel/debug/ieee80211/phy0/ath11k/spectral_scan0 > fft_samples.dump Tested-on: IPQ8074 WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1 Signed-off-by:
Karthikeyan Periyasamy <periyasa@codeaurora.org> Signed-off-by:
-
Karthikeyan Periyasamy authored
Add direct buffer ring (dbring) with helper API, which is used by the spectral scan. Initialise the direct buffer ring based on the dma ring capability, which get announced in the wmi service ready extended event. This ring is slightly changed from data path rings. Compare to data path ring this ring shares the hp and tp address to firmware though WMI commands. Also the replenish buffer size is derived from firmware announcement. driver receive indication through WMI event WMI_PDEV_DMA_RING_BUF_RELEASE_EVENTID. Tested-on: IPQ8074 WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1 Signed-off-by:
-
- 11 Jun, 2020 9 commits
-
-
Rajkumar Manoharan authored
Build 6 GHz band capability from HT and VHT capabilities reported by firmware. Signed-off-by:
Rajkumar Manoharan <rmanohar@codeaurora.org> Signed-off-by:
-
Pradeep Kumar Chitrapu authored
Add support for 6Ghz short ssid and bssid hint mechanism as part of scan command. Signed-off-by:
Pradeep Kumar Chitrapu <pradeepc@codeaurora.org> Signed-off-by:
-
Pradeep Kumar Chitrapu authored
With addition of 6Ghz channels, it is possible that wmi buffer size can exceed the maximum wmi buffer size. So iterate over the channel list, and send multiple messages till channel list is empty. Also mark PSC channel flag for 6GHz channels accordingly. Signed-off-by:
-
Pradeep Kumar Chitrapu authored
Add 6G scan active and passive dwell time parameter to scan request. Signed-off-by:
-
Pradeep Kumar Chitrapu authored
If 6 ghz channel is a Preferred Scanning Channel(PSC), mark the channel flag accordingly when updating channel list to firmware. This will be used when making scanning decision in 6GHz channels. Signed-off-by:
-
Pradeep Kumar Chitrapu authored
This adds support required for configuring min_data_rate of 6GHz oper IE and peer_he_caps_6ghz in peer assoc command. The Minimum Rate field indicates the minimum rate, in units of 1 Mb/s, that the non-AP STA is allowed to use for sending PPDUs as defined in IEEE P802.11ax
™ /D6.0. Signed-off-by: -
Pradeep Kumar Chitrapu authored
As 6GHz cahnnel numbers overlap with those of 5GHz and 2GHz bands, it is necessary to use frequency when determining the band info in rx path. Signed-off-by:
-
Pradeep Kumar Chitrapu authored
This patch adds 6GHz band support and mac80211 registration for the 6G phy radio. Signed-off-by:
-
Pradeep Kumar Chitrapu authored
This patch adds support for 6GHz frequency listing. Signed-off-by:
-
- 09 Jun, 2020 2 commits
-
-
Flavio Suligoi authored
In some ath files, the wiki url is still the old "wireless.kernel.org" instead of the new "wireless.wiki.kernel.org" Signed-off-by:
Flavio Suligoi <f.suligoi@asem.it> Signed-off-by:
-
Evan Green authored
ath10k_htt_tx_free_msdu_id() has a lockdep assertion that htt->tx_lock is held. Acquire the lock in a couple of error paths when calling that function to ensure this condition is met. Fixes: 6421969f ("ath10k: refactor tx pending management") Fixes: e62ee5c3 ("ath10k: Add support for htt_data_tx_desc_64 descriptor") Signed-off-by:
Evan Green <evgreen@chromium.org> Signed-off-by:
-
- 01 Jun, 2020 1 commit
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netDavid S. Miller authored
xdp_umem.c had overlapping changes between the 64-bit math fix for the calculation of npgs and the removal of the zerocopy memory type which got rid of the chunk_size_nohdr member. The mlx5 Kconfig conflict is a case where we just take the net-next copy of the Kconfig entry dependency as it takes on the ESWITCH dependency by one level of indirection which is what the 'net' conflicting change is trying to ensure. Signed-off-by:David S. Miller <davem@davemloft.net>
-
- 31 May, 2020 25 commits
-
-
David S. Miller authored
Merge tag 'mac80211-next-for-davem-2020-05-31' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next Johannes Berg says: ==================== Another set of changes, including * many 6 GHz changes, though it's not _quite_ complete (I left out scanning for now, we're still discussing) * allow userspace SA-query processing for operating channel validation * TX status for control port TX, for AP-side operation * more per-STA/TID control options * move to kHz for channels, for future S1G operation * various other small changes ==================== Signed-off-by:
-
Joe Perches authored
Yes, staying withing 80 columns is certainly still _preferred_. But it's not the hard limit that the checkpatch warnings imply, and other concerns can most certainly dominate. Increase the default limit to 100 characters. Not because 100 characters is some hard limit either, but that's certainly a "what are you doing" kind of value and less likely to be about the occasional slightly longer lines. Miscellanea: - to avoid unnecessary whitespace changes in files, checkpatch will no longer emit a warning about line length when scanning files unless --strict is also used - Add a bit to coding-style about alignment to open parenthesis Signed-off-by:
Joe Perches <joe@perches.com> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull x86 fixes from Thomas Gleixner: "A pile of x86 fixes: - Prevent a memory leak in ioperm which was caused by the stupid assumption that the exit cleanup is always called for current, which is not the case when fork fails after taking a reference on the ioperm bitmap. - Fix an arithmething overflow in the DMA code on 32bit systems - Fill gaps in the xstate copy with defaults instead of leaving them uninitialized - Revert: "Make __X32_SYSCALL_BIT be unsigned long" as it turned out that existing user space fails to build" * tag 'x86-urgent-2020-05-31' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/ioperm: Prevent a memory leak when fork fails x86/dma: Fix max PFN arithmetic overflow on 32 bit systems copy_xstate_to_kernel(): don't leave parts of destination uninitialized x86/syscalls: Revert "x86/syscalls: Make __X32_SYSCALL_BIT be unsigned long" -
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull scheduler fix from Thomas Gleixner: "A single scheduler fix preventing a crash in NUMA balancing. The current->mm check is not reliable as the mm might be temporary due to use_mm() in a kthread. Check for PF_KTHREAD explictly" * tag 'sched-urgent-2020-05-31' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: sched/fair: Don't NUMA balance for kthreads
-
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netLinus Torvalds authored
Pull networking fixes from David Miller: "Another week, another set of bug fixes: 1) Fix pskb_pull length in __xfrm_transport_prep(), from Xin Long. 2) Fix double xfrm_state put in esp{4,6}_gro_receive(), also from Xin Long. 3) Re-arm discovery timer properly in mac80211 mesh code, from Linus Lüssing. 4) Prevent buffer overflows in nf_conntrack_pptp debug code, from Pablo Neira Ayuso. 5) Fix race in ktls code between tls_sw_recvmsg() and tls_decrypt_done(), from Vinay Kumar Yadav. 6) Fix crashes on TCP fallback in MPTCP code, from Paolo Abeni. 7) More validation is necessary of untrusted GSO packets coming from virtualization devices, from Willem de Bruijn. 8) Fix endianness of bnxt_en firmware message length accesses, from Edwin Peer. 9) Fix infinite loop in sch_fq_pie, from Davide Caratti. 10) Fix lockdep splat in DSA by setting lockless TX in netdev features for slave ports, from Vladimir Oltean. 11) Fix suspend/resume crashes in mlx5, from Mark Bloch. 12) Fix use after free in bpf fmod_ret, from Alexei Starovoitov. 13) ARP retransmit timer guard uses wrong offset, from Hongbin Liu. 14) Fix leak in inetdev_init(), from Yang Yingliang. 15) Don't try to use inet hash and unhash in l2tp code, results in crashes. From Eric Dumazet" * git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (77 commits) l2tp: add sk_family checks to l2tp_validate_socket l2tp: do not use inet_hash()/inet_unhash() net: qrtr: Allocate workqueue before kernel_bind mptcp: remove msk from the token container at destruction time. mptcp: fix race between MP_JOIN and close mptcp: fix unblocking connect() net/sched: act_ct: add nat mangle action only for NAT-conntrack devinet: fix memleak in inetdev_init() virtio_vsock: Fix race condition in virtio_transport_recv_pkt drivers/net/ibmvnic: Update VNIC protocol version reporting NFC: st21nfca: add missed kfree_skb() in an error path neigh: fix ARP retransmit timer guard bpf, selftests: Add a verifier test for assigning 32bit reg states to 64bit ones bpf, selftests: Verifier bounds tests need to be updated bpf: Fix a verifier issue when assigning 32bit reg states to 64bit ones bpf: Fix use-after-free in fmod_ret check net/mlx5e: replace EINVAL in mlx5e_flower_parse_meta() net/mlx5e: Fix MLX5_TC_CT dependencies net/mlx5e: Properly set default values when disabling adaptive moderation net/mlx5e: Fix arch depending casting issue in FEC ... -
Nathan Errera authored
With some newer AKMs, the KCK and KEK are bigger, so allow that if the driver advertises support for it. In addition, add a new attribute for the AKM so we can use it for offloaded rekeying. Signed-off-by:
Nathan Errera <nathan.errera@intel.com> [reword commit message] Link: https://lore.kernel.org/r/20200528212237.5eb58b00a5d1.I61b09d77c4f382e8d58a05dcca78096e99a6bc15@changeidSigned-off-by:
Johannes Berg <johannes.berg@intel.com>
-
Tova Mussai authored
Set short slot also for 6 GHz band, just like 5 GHz. Signed-off-by:
Tova Mussai <tova.mussai@intel.com> Link: https://lore.kernel.org/r/20200528213443.75f38e6f5efd.I272fbae402b03123f04e9ae69204eeab960c70cd@changeidSigned-off-by:
-
Ilan Peer authored
Treat it like the 5 GHz band. Signed-off-by:
Ilan Peer <ilan.peer@intel.com> Link: https://lore.kernel.org/r/20200528213443.889e5c9dd006.Id8ed3bb8000ba8738be5df05639415eb2e23c61a@changeidSigned-off-by:
-
Johannes Berg authored
On 6 GHz, stations don't have ht_supported set, but they can still do aggregation since they must have HE, allow that. Link: https://lore.kernel.org/r/20200528213443.776d3c891b64.Ifa099d450617b50c691832b3c4aa08959fab520a@changeidSigned-off-by:
-
Johannes Berg authored
On 6 GHz band, HE capabilities must be available for all of the interface types, otherwise we shouldn't use 6 GHz. Check this. Link: https://lore.kernel.org/r/20200528213443.5881cb3c8c4a.I583b54172f91f98d44af64a16c5826fe458cbb27@changeidSigned-off-by:
-
Johannes Berg authored
On the 6 GHz band, HE should be used, but without any direct HT/VHT capabilities, instead the HE 6 GHz band capabilities will capture the relevant information. Reject HT/VHT capabilities here. Link: https://lore.kernel.org/r/20200528213443.bfe89c35459a.Ibba5e066fa0087fd49d13cfee89d196ea0c68ae2@changeidSigned-off-by:
-
Johannes Berg authored
If a 6 GHz channel exists, then we can probably safely assume that the device actually supports it, and then it should support most bandwidths. This will probably need to be extended to check the interface type and then dig into the HE capabilities for that though, to have the correct bandwidth check. Link: https://lore.kernel.org/r/20200528213443.d4864ef52e92.I82f09b2b14a56413ce20376d09967fe954a033eb@changeidSigned-off-by:
-
Ilan Peer authored
On 6 GHz, the 6 GHz capabilities element should be added, do that. Signed-off-by:
-
Johannes Berg authored
In order to handle 6 GHz AP side, take the HE 6 GHz band capability data and pass it to the driver (which needs it for A-MPDU spacing and A-MPDU length). Link: https://lore.kernel.org/r/1589399105-25472-6-git-send-email-rmanohar@codeaurora.orgCo-developed-by:
-
Shaul Triebitz authored
An AP supporting EMA (Enhanced Multi-BSSID advertisement) should set bit 83 in the extended capabilities IE (9.4.2.26 in the 802.11ax D5 spec). So the *3rd* bit of the 10th byte should be checked. Also, in one place, the wrong byte was checked. (cfg80211_find_ie returns a pointer to the beginning of the IE, so the data really starts at ie[2], so the 10th byte should be ie[12]. To avoid this confusion, use cfg80211_find_elem instead). Signed-off-by:
Shaul Triebitz <shaul.triebitz@intel.com> Link: https://lore.kernel.org/r/20200528213443.4316121fa2a3.I9745582f8d41ad8e689dac0fefcd70b276d7c1ea@changeidSigned-off-by:
-
Johannes Berg authored
Support connecting to HE 6 GHz APs and mesh networks on 6 GHz, where the HT/VHT information is missing but instead the HE 6 GHz band capability is present, and the 6 GHz Operation information field is used to encode the channel configuration instead of the HT/VHT operation elements. Also add some other bits needed to connect to 6 GHz networks. Link: https://lore.kernel.org/r/1589399105-25472-10-git-send-email-rmanohar@codeaurora.orgCo-developed-by:
-
Johannes Berg authored
If the AP advertises inconsistent data, namely it has CCFS1 or CCFS2, but doesn't advertise support for 160/80+80 bandwidth or "Extended NSS BW Support", then we cannot use any MCSes in the the higher bandwidth. Thus, avoid connecting with higher bandwidth since it's less efficient that way. Link: https://lore.kernel.org/r/20200528213443.0e55d40c3ccc.I6fd0b4708ebd087e5e46466c3e91f6efbcbef668@changeidSigned-off-by:
-
Rajkumar Manoharan authored
As HT/VHT elements are not allowed in 6 GHz band, do not include them in mesh beacon template formation. Signed-off-by:
-
Rajkumar Manoharan authored
Add 6 GHz operation information (IEEE 802.11ax/D6.0, Figure 9-787k) while building HE operation element for non-HE AP. This field is used to determine channel information in the absence of HT/VHT IEs. Signed-off-by:
-
Rajkumar Manoharan authored
Construct HE 6 GHz band capability element (IEEE 802.11ax/D6.0, 9.4.2.261) for association request and mesh beacon. The 6 GHz capability information is passed by driver through iftypes caps. Signed-off-by:
-
Johannes Berg authored
These capabilities cover what would otherwise be transported in HT/VHT capabilities, but only a subset thereof that is actually needed on 6 GHz with HE already present. Expose the capabilities to userspace, drivers are expected to set them as using the 6 GHz band (currently) requires HE capability. Link: https://lore.kernel.org/r/20200528213443.244cd5cb9db8.Icd8c773277a88c837e7e3af1d4d1013cc3b66543@changeidSigned-off-by:
-
Rajkumar Manoharan authored
Handle 6 GHz band capability element parsing for association. Signed-off-by:
-
Rajkumar Manoharan authored
Handle 6 GHz HE capability while adding new station. It will be used later in mac80211 station processing. Signed-off-by:
-
Johannes Berg authored
Add the HE extended element IDs and the definitions for the HE 6 GHz band capabilities element, from Draft 5.0. Link: https://lore.kernel.org/r/20200528213443.1a6689fe093f.Ifdc5400fb01779351354daf38663ebeea03c9ad9@changeidSigned-off-by:
-
Johannes Berg authored
Add some code to obtain and parse the 6 GHz operation field inside the HE operation element. While at it, fix the required length using sizeof() the new struct, which is 5 instead of 4 now. Link: https://lore.kernel.org/r/20200528213443.42ca72c45ca9.Id74bc1b03da9ea6574f9bc70deeb60dfc1634359@changeidSigned-off-by:
-
