- 03 Dec, 2009 24 commits
-
-
Alan Cox authored
We were never able to get docs for this out of Toshiba for years. Dave Barnes produced a NetBSD driver however and from that we can fill in the needed tables. As we correct the PCI identifiers a bit also update the old ide generic driver at the same time so it stays compiling. Signed-off-by:
Alan Cox <alan@linux.intel.com> Signed-off-by:
Jeff Garzik <jgarzik@redhat.com>
-
Alan Cox authored
Making the new stuff work broke some of the old chipsets. We need to go back to the old set up values for these it seems. Unfortunately even with documentation this is basically a mix of cargoculting and guesswork. Chased down to the exact line by Gianluca. Signed-off-by:
-
Alan Cox authored
Signed-off-by:
-
Alan Cox authored
Daniela Engert pointed out that there are some implementation notes for the 643 and 646 that deal with certain serialization rules. In theory we don't need them because they apply when the motherboard decides not to retry PCI requests for long enough and the chip is busy doing a DMA transfer on the other channel. The rule basically is "don't touch the taskfile of the other channel while a DMA is in progress". To implement that we need to - not issue a command on a channel when there is a DMA command queued - not issue a DMA command on a channel when there are PIO commands queued - use the alternative access to the interrupt source so that we do not touch altstatus or status on shared IRQ. Updated to remote extra conditional check Bartlomiej noted and to remove the variables for irq checks as the CMD648 doesn't have the underlying problem. Signed-off-by:
-
Alan Cox authored
Bartlomiej pointed out that while this got fixed in the old driver whoever did it didn't port it across. Signed-off-by:
-
Alan Cox authored
Reported by Mikulas Patocka. VIA VT82C586B + Transcend TS64GSSD25-M v0826 does not work in UDMA mode Signed-off-by:
-
Benjamin Herrenschmidt authored
In libata-sff, ata_sff_post_internal_cmd() directly calls ata_bmdma_stop() instead of ap->ops->bmdma_stop(). This can be a problem for controllers that use their own bmdma_stop for which the generic sff one isn't suitable Signed-off-by:
Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by:
-
Christoph Hellwig authored
Add support for the ATA TRIM command in libata. We translate a WRITE SAME 16 command with the unmap bit set into an ATA TRIM command and export enough information in READ CAPACITY 16 and the block limits EVPD page so that the new SCSI layer discard support will driver this for us. Note that I hardcode the WRITE_SAME_16 opcode for now as the patch to introduce the symbolic is not in 2.6.32 yet but only in the SCSI tree - as soon as it is merged we can fix it up to properly use the symbolic name. Signed-off-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
-
Tejun Heo authored
If ATA device failed FLUSH, it means that the device failed to write out some amount of data and the error needs to be reported to upper layers. As retries can't recover the lost data, FLUSH failures need to be reported immediately in general. However, if FLUSH fails due to transmission errors, the FLUSH needs to be retried; otherwise, filesystems may switch to RO mode and/or raid array may drop a drive for a random transmission glitch. This condition can be rather easily reproduced on certain ahci controllers which go through a PHY event after powersave mode switch + ext4 combination. Powersave mode switch is often closely followed by flush from the filesystem failing the FLUSH with ATA bus error which makes the filesystem code believe that data is lost and drop to RO mode. This was reported in the following bugzilla bug. http://bugzilla.kernel.org/show_bug.cgi?id=14543 This patch makes libata EH retry FLUSH if it wasn't failed by the device. Signed-off-by:
Tejun Heo <tj@kernel.org> Reported-by:
Andrey Vihrov <andrey.vihrov@gmail.com> Signed-off-by:
-
ashish kalra authored
Enable device hot-plug support on Port multiplier fan-out ports Signed-off-by:
Ashish Kalra <Ashish.Kalra@freescale.com> Signed-off-by:
-
Bartlomiej Zolnierkiewicz authored
Alan Cox reported that cable detection sometimes works unreliably for HPT3xxN and that the issue is fixed by adding debounce delay as used by the vendor driver. Sergei Shtylyov also noticed that debounce delay is needed for all HPT37x and HPT3xxN chipsets according to vendor drivers. Signed-off-by:
Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Signed-off-by:
-
Bartlomiej Zolnierkiewicz authored
The detection was reversed between primary and secondary ports. Fix it to match hpt366 and the vendor driver. Signed-off-by:
-
Matthew Garrett authored
sysfs attributes shouldn't require newlines. Make it possible to set the link power management policy without a trailing newline. Signed-off-by:
Matthew Garrett <mjg@redhat.com> Signed-off-by:
-
Otavio Salvador authored
Signed-off-by:
Otavio Salvador <otavio@ossystems.com.br> Signed-off-by:
-
Bartlomiej Zolnierkiewicz authored
We can use the same ->pre_reset method for all HPT37x chipsets now. Signed-off-by:
-
Bartlomiej Zolnierkiewicz authored
Signed-off-by:
-
Shaohua Li authored
I obseved there is a sata_async_notification() for every ahci interrupt. But the async notification does nothing (this is hard disk drive and no pmp). This cause cpu wastes some time on sntf register access. It appears ICH AHCI doesn't support SNotification register, but the controller reports it does. After quirking it, the async notification disappears. PS. it appears all ICH don't support SNotification register from ICH manual, don't know if we need quirk all ICH. I don't have machines with all kinds of ICH. Signed-off-by:
Shaohua Li <shaohua.li@intel.com> Signed-off-by:
-
Vivek Mahajan authored
The following patch adds MSI support. Some platforms may have broken MSI, so those are defaulted to use legacy PCI interrupts. Signed-off-by:
Vivek Mahajan <vivek.mahajan@freescale.com> Signed-off-by:
-
Robert Hancock authored
Remove the experimental tag on Parallel ATA drivers. Though some of the individual PATA drivers are still marked as experimental, as a group they can hardly be considered to be, given they've been used in various distros for some time. Signed-off-by:
Robert Hancock <hancockrwd@gmail.com> Signed-off-by:
-
Thiago Farina authored
Use ARRAY_SIZE macro of kernel api instead. Signed-off-by:
Thiago Farina <tfransosi@gmail.com> Signed-off-by:
-
Jiri Slaby authored
In via_init_one, when via_isa_bridges iterator reaches PCI_DEVICE_ID_VIA_ANON and last but one via_isa_bridges bridge is found but rev doesn't match, pci_dev_put(isa) is called twice. Do pci_dev_put only once. Signed-off-by:
Jiri Slaby <jirislaby@gmail.com> Signed-off-by:
-
Krzysztof Halasa authored
Tested on IXP425 + CS5536. Signed-off-by:
Krzysztof Hałasa <khc@pm.waw.pl> Signed-off-by:
-
Tejun Heo authored
Missing _SDD is not an error. Don't treat it as one. Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Linus Torvalds authored
-
- 02 Dec, 2009 16 commits
-
-
Julia Lawall authored
request_region should be used with release_region, not request_mem_region. Geert Uytterhoeven pointed out that in the case of drivers/video/gbefb.c, the problem is actually the other way around; request_mem_region should be used instead of request_region. The semantic patch that finds/fixes this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> @r1@ expression start; @@ request_region(start,...) @b1@ expression r1.start; @@ request_mem_region(start,...) @depends on !b1@ expression r1.start; expression E; @@ - release_mem_region + release_region (start,E) // </smpl> Signed-off-by:
Julia Lawall <julia@diku.dk> Signed-off-by:
Ralf Baechle <ralf@linux-mips.org>
-
Atsushi Nemoto authored
TXx9 SPI bit rate is calculated by: fBR = (spi-baseclk) / (n + 1) Fix calculation of min_speed_hz, max_speed_hz and n. Signed-off-by:Atsushi Nemoto <anemo@mba.ocn.ne.jp> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6Linus Torvalds authored
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: mfd: Correct WM831X_MAX_ISEL_VALUE
-
Anisse Astier authored
These laptops often leave i8042 in a wierd state resulting in non- operational touchpad and keyboard. Signed-off-by:
Anisse Astier <anisse@astier.eu> Signed-off-by:
Dmitry Torokhov <dtor@mail.ru> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
git://neil.brown.name/mdLinus Torvalds authored
* 'for-linus' of git://neil.brown.name/md: md: revert incorrect fix for read error handling in raid1.
-
Rusty Russell authored
Jon confirms that recent modprobe will look in /proc/cmdline, so these cmdline options can still be used. See http://bugzilla.kernel.org/show_bug.cgi?id=14164Reported-by:
Adam Williamson <awilliam@redhat.com> Cc: stable@kernel.org Signed-off-by:
Rusty Russell <rusty@rustcorp.com.au> Signed-off-by:
-
git://ftp.linux-mips.org/pub/scm/upstream-linusLinus Torvalds authored
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: MIPS: RB532: Fix devices.c compilation. MIPS: Fix MIPS I build.
-
git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdogLinus Torvalds authored
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog: [PATCH] rc32434_wdt: fix compilation failure [WATCHDOG] rc32434_wdt.c: use resource_size()
-
Helge Deller authored
On the parisc architecture we face for each and every loaded kernel module this kernel "badness warning": sysfs: cannot create duplicate filename '/module/ac97_bus/sections/.text' Badness at fs/sysfs/dir.c:487 Reason for that is, that on parisc all kernel modules do have multiple .text sections due to the usage of the -ffunction-sections compiler flag which is needed to reach all jump targets on this platform. An objdump on such a kernel module gives: Sections: Idx Name Size VMA LMA File off Algn 0 .note.gnu.build-id 00000024 00000000 00000000 00000034 2**2 CONTENTS, ALLOC, LOAD, READONLY, DATA 1 .text 00000000 00000000 00000000 00000058 2**0 CONTENTS, ALLOC, LOAD, READONLY, CODE 2 .text.ac97_bus_match 0000001c 00000000 00000000 00000058 2**2 CONTENTS, ALLOC, LOAD, READONLY, CODE 3 .text 00000000 00000000 00000000 000000d4 2**0 CONTENTS, ALLOC, LOAD, READONLY, CODE ... Since the .text sections are empty (size of 0 bytes) and won't be loaded by the kernel module loader anyway, I don't see a reason why such sections need to be listed under /sys/module/<module_name>/sections/<section_name> either. The attached patch does solve this issue by not exporting section names which are empty. This fixes bugzilla http://bugzilla.kernel.org/show_bug.cgi?id=14703Signed-off-by:Helge Deller <deller@gmx.de> CC: rusty@rustcorp.com.au CC: akpm@linux-foundation.org CC: James.Bottomley@HansenPartnership.com CC: roland@redhat.com CC: dave@hiauly1.hia.nrc.ca Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6Linus Torvalds authored
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6: regulator: Initialise wm831x structure pointor for ISINK driver
-
Mark Brown authored
The version that made it into mainline missed the initialisation of the chip handle. Signed-off-by:
Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by:
Liam Girdwood <lrg@slimlogic.co.uk>
-
Florian Fainelli authored
We should now use dev_set_drvdata to set the driver driver_data field. Signed-off-by:
Florian Fainelli <florian@openwrt.org> Patchwork: http://patchwork.linux-mips.org/patch/747/Signed-off-by:
-
Ralf Baechle authored
Broken by d63c63e889bbeeaa461a8addf1245f89f3ce4ece (lmo) rsp. f1e39a4a (kernel.org). Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/ycmiao/pxa-linux-2.6Linus Torvalds authored
* 'fix' of git://git.kernel.org/pub/scm/linux/kernel/git/ycmiao/pxa-linux-2.6: [ARM] pxamci: call mmc_remove_host() before freeing resources
-
Daniel Mack authored
mmc_remove_host() will cause the mmc core to switch off the bus power by eventually calling pxamci_set_ios(). This function uses the regulator or the GPIO which have been freed already. This causes the following Oops on module unload. [ 49.519649] Unable to handle kernel paging request at virtual address 30303a70 [ 49.526878] pgd = c7084000 [ 49.529563] [30303a70] *pgd=00000000 [ 49.533136] Internal error: Oops: 5 [#1] [ 49.537025] last sysfs file: /sys/devices/platform/pxa27x-ohci/usb1/1-1/1-1:1.0/host0/target0:0:0/0:0:0:0/scsi_level [ 49.547471] Modules linked in: pxamci(-) eeti_ts [ 49.552061] CPU: 0 Not tainted (2.6.32-rc8 #322) [ 49.557001] PC is at regulator_is_enabled+0x3c/0xbc [ 49.561846] LR is at regulator_is_enabled+0x30/0xbc [ 49.566691] pc : [<c01a2448>] lr : [<c01a243c>] psr: 60000013 [ 49.566702] sp : c7083e70 ip : 30303a30 fp : 00000000 [ 49.578093] r10: c705e200 r9 : c7082000 r8 : c705e2e0 [ 49.583280] r7 : c7061340 r6 : c7061340 r5 : c7083e70 r4 : 00000000 [ 49.589759] r3 : c04dc434 r2 : c04dc434 r1 : c03eecea r0 : 00000047 [ 49.596241] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user [ 49.603329] Control: 0000397f Table: a7084018 DAC: 00000015 [ 49.609031] Process rmmod (pid: 1101, stack limit = 0xc7082278) [ 49.614908] Stack: (0xc7083e70 to 0xc7084000) [ 49.619238] 3e60: c7082000 c703c4f8 c705ea00 c04f4074 [ 49.627366] 3e80: 00000000 c705e3a0 ffffffff c0247ddc c70361a0 00000000 c705e3a0 ffffffff [ 49.635499] 3ea0: c705e200 bf006400 c78c4f00 c705e200 c705e3a0 ffffffff c705e200 ffffffff [ 49.643633] 3ec0: c04d8ac8 c02476d0 ffffffff c0247c60 c705e200 c0248678 c705e200 c0249064 [ 49.651765] 3ee0: ffffffff bf006204 c04d8ad0 c04d8ad0 c04d8ac8 bf007490 00000880 c00440c4 [ 49.659898] 3f00: 0000b748 c01c5708 bf007490 c01c44c8 c04d8ac8 c04d8afc bf007490 c01c4570 [ 49.668031] 3f20: bf007490 bf00750c c04f4258 c01c37a4 00000000 bf00750c c7083f44 c007b014 [ 49.676162] 3f40: 4000d000 6d617870 08006963 00000001 00000000 c7085000 00000001 00000000 [ 49.684287] 3f60: 4000d000 c7083f8c 00000001 bea01a54 00005401 c7ab1400 c00440c4 00082000 [ 49.692420] 3f80: bf00750c 00000880 c7083f8c 00000000 4000cfa8 00000000 00000880 bea01cc8 [ 49.700552] 3fa0: 00000081 c0043f40 00000000 00000880 bea01cc8 00000880 00000006 00000000 [ 49.708677] 3fc0: 00000000 00000880 bea01cc8 00000081 00000097 0000cca4 0000b748 00000000 [ 49.716802] 3fe0: 4001a4f0 bea01cc0 00018bf4 4001a4fc 20000010 bea01cc8 a063e021 a063e421 [ 49.724958] [<c01a2448>] (regulator_is_enabled+0x3c/0xbc) from [<c0247ddc>] (mmc_regulator_set_ocr+0x14/0xd8) [ 49.734836] [<c0247ddc>] (mmc_regulator_set_ocr+0x14/0xd8) from [<bf006400>] (pxamci_set_ios+0xd8/0x17c [pxamci]) [ 49.745044] [<bf006400>] (pxamci_set_ios+0xd8/0x17c [pxamci]) from [<c02476d0>] (mmc_power_off+0x50/0x58) [ 49.754555] [<c02476d0>] (mmc_power_off+0x50/0x58) from [<c0247c60>] (mmc_detach_bus+0x68/0xc4) [ 49.763207] [<c0247c60>] (mmc_detach_bus+0x68/0xc4) from [<c0248678>] (mmc_stop_host+0xd4/0x1bc) [ 49.771944] [<c0248678>] (mmc_stop_host+0xd4/0x1bc) from [<c0249064>] (mmc_remove_host+0xc/0x20) [ 49.780681] [<c0249064>] (mmc_remove_host+0xc/0x20) from [<bf006204>] (pxamci_remove+0xc8/0x174 [pxamci]) [ 49.790211] [<bf006204>] (pxamci_remove+0xc8/0x174 [pxamci]) from [<c01c5708>] (platform_drv_remove+0x1c/0x24) [ 49.800164] [<c01c5708>] (platform_drv_remove+0x1c/0x24) from [<c01c44c8>] (__device_release_driver+0x7c/0xc4) [ 49.810110] [<c01c44c8>] (__device_release_driver+0x7c/0xc4) from [<c01c4570>] (driver_detach+0x60/0x8c) [ 49.819535] [<c01c4570>] (driver_detach+0x60/0x8c) from [<c01c37a4>] (bus_remove_driver+0x90/0xcc) [ 49.828452] [<c01c37a4>] (bus_remove_driver+0x90/0xcc) from [<c007b014>] (sys_delete_module+0x1d8/0x254) [ 49.837891] [<c007b014>] (sys_delete_module+0x1d8/0x254) from [<c0043f40>] (ret_fast_syscall+0x0/0x28) [ 49.847145] Code: eb06c53a e596c030 e1a0500d e59f106c (e59c0040) [ 49.853566] ---[ end trace b5fa66a00cea142f ]--- Signed-off-by:
Daniel Mack <daniel@caiaq.de> Reported-by:
Sven Neumann <s.neumann@raumfeld.com> Cc: Pierre Ossman <pierre@ossman.eu> Cc: linux-mmc@vger.kernel.org Cc: linux-arm-kernel@lists.infradead.org Cc: stable@kernel.org Signed-off-by:
Eric Miao <eric.y.miao@gmail.com>
-
Florian Fainelli authored
This patch fixes the compilation failure of rc32434 due to a bad module parameter description. Signed-off-by:
Wim Van Sebroeck <wim@iguana.be>
-
