Pull spi updates from Mark Brown:
 "Quite a quiet release for SPI, there are no changes at all to the core
  and not that many changes to drivers. Highlights of those driver
  changes include:

   - SH MSIOF support for GPIO chip selects contributed by Geert
     Uytterhoeven.

   - Full duplex support for a3700 contributed by Maxime Chevallier.

   - Support for DMA transfers on Atmel devices that require a bounce
     buffer contributed by Radu Pirea"

* tag 'spi-v4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (31 commits)
  spi: dw: Remove unused members from struct chip_data
  spi: orion: Fix a resource leak if the optional "axi" clk is deferred
  spi: a3700: Remove endianness swapping for full-duplex transfers
  spi: a3700: Remove endianness swapping functions when accessing FIFOs
  spi: a3700: Add full-duplex support
  spi: a3700: Allow to enable or disable FIFO mode
  spi: a3700: Set frequency limits at startup
  spi: a3700: Clear DATA_OUT when performing a read
  spi: orion: Fix clock resource by adding an optional bus clock
  spi: s3c64xx: add SPDX identifier
  spi: imx: do not access registers while clocks disabled
  spi: atmel: Implements transfers with bounce buffer
  spi: sh-msiof: Fix timeout failures for TX-only DMA transfers
  spi: spi-fsl-dspi: account for const type of of_device_id.data
  spi: bcm53xx: simplify reading SPI data
  spi: sirf: account for const type of of_device_id.data
  spi: pxa2xx: Use gpiod_put() not gpiod_free()
  spi: pxa2xx: avoid redundant gpio_to_desc(desc_to_gpio()) round-trip
  spi: sh-msiof: Document hardware limitations related to chip selects
  spi: sh-msiof: Implement cs-gpios configuration
  ...

Pull MMC updates from Ulf Hansson:
 "There are two major achievements for MMC in this release, which
  deserves to be specially highlighted.

  First, we have converted the MMC block device from using the legacy
  blk interface into using the modern blkmq interface. Not only do we
  get all the nice effects from using blkmq, but it also means that new
  fresh nice code replaces old rusty code. Great news to everybody that
  cares about MMC/SD!

  It should also be noted that converting to blkmq has not been trivial,
  mostly because of that we have been carrying too much of MMC specific
  optimizations for the I/O request path, rather than striving to move
  these to the generic blk layer. Hopefully we won't be doing that
  mistake, ever again.

  Special thanks to Adrian Hunter (Intel) and to Linus Walleij (Linaro),
  who both have been working on this for quite some time!

  Second, on top of the blkmq deployment, we have enabled full support
  the eMMC command queuing feature, introduced in the eMMC v.5.1 spec.
  This also includes an implementation of a host driver library,
  supporting the corresponding CQHCI HW. Ideally, those controllers that
  supports CQHCI should only need some minor adaptations to make this
  play.

  So far the sdhci-pci driver for the Intel GLKs and the sdhci-of-arasan
  driver used on Rockchip RK3399, have enabled support for eMMC command
  queueing.

  Worth to highlight is also that, implementing the eMMC command queuing
  support has been a collaborative effort, as several people from
  Codeaurora, Rockchip, Intel and Linaro have been involved. However,
  the work has been driven by Adrian Hunter (Intel).

  In some shadow of the above, here are the rest of the highlights:

  MMC core:
   - Don't remove non-removable cards during system suspend
   - Add a slot-gpio helper to check capability of GPIO WP detection

  MMC host:
   - sdhci: Cleanups and improvements of some wakeup related code
   - sdhci-pci-arasan: New variant to support Arasan PCI HW with integrated phy
   - sdhci-acpi: Avoid broken UHS transfer modes on Intel CHT
   - sdhci-acpi: Add support for ACPI HID of AMD Controller with HS400
   - sdhci_f_sdh30: Add ACPI support
   - sdhci-esdhc-imx: Enable/disable clock at runtime suspend/resume
   - sdhci-of-esdhc: A few minor fixes
   - mmci: Add support for new STM32 variant
   - renesas_sdhi: enable R-Car D3 (r8a77995) support
   - tmio/renesas_sdhi: Re-structuring, cleanups and modernizations"

* tag 'mmc-v4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (96 commits)
  mmc: mmci: fix error return code in mmci_probe()
  mmc: davinci: suppress error message on EPROBE_DEFER
  mmc: davinci: dont' use module_platform_driver_probe()
  mmc: tmio: hide unused tmio_mmc_clk_disable/tmio_mmc_clk_enable functions
  mmc: mmci: Add STM32 variant
  mmc: mmci: Add support for setting pad type via pinctrl
  mmc: mmci: Don't pretend all variants to have OPENDRAIN bit
  mmc: mmci: Don't pretend all variants to have MCI_STARBITERR flag
  mmc: mmci: Don't pretend all variants to have MMCIMASK1 register
  mmc: tmio: refactor .get_ro hook
  mmc: slot-gpio: add a helper to check capability of GPIO WP detection
  mmc: tmio: remove dma_ops from tmio_mmc_host_probe() argument
  mmc: tmio: move {tmio_}mmc_of_parse() to tmio_mmc_host_alloc()
  mmc: tmio: move clk_enable/disable out of tmio_mmc_host_probe()
  mmc: tmio: ioremap memory resource in tmio_mmc_host_alloc()
  mmc: sh_mmcif: remove redundant initialization of 'opc'
  mmc: sdhci: Rework sdhci_enable_irq_wakeups()
  mmc: sdhci: Handle failure of enable_irq_wake()
  mmc: sdhci: Stop exporting sdhci_enable_irq_wakeups()
  mmc: sdhci-pci: Use device wakeup capability to determine MMC_PM_WAKE_SDIO_IRQ capability
  ...

Merge tag 'hwmon-for-linus-v4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull hwmon updates from Guenter Roeck:

 - New driver for W83773G

 - Fan control support for PMBus drivers

 - Improvements and minor fixes in several drivers

* tag 'hwmon-for-linus-v4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (32 commits)
  hwmon: (dell-smm) Disable fan support for Dell Vostro 3360
  hwmon: (dell-smm) Disable fan support for Dell Inspiron 7720
  hwmon: (dell-smm) Enable broken functionality via "force" module param
  hwmon: (k10temp) Add temperature offset for Ryzen 1900X
  hwmon: (lm75) Fix trailing semicolon
  hwmon: (ina2xx) Fix access to uninitialized mutex
  hwmon: (pmbus/ir35221) Remove unnecessary scaling
  hwmon: (sht3x) wait predefined limits loading complete before access
  hwmon: (pmbus/ibm-cffps) Add dependency on LEDS_CLASS
  hwmon: (pmbus/cffps) Add led class device for power supply fault led
  hwmon: (pmbus) cffps: Add PMBUS_SKIP_STATUS_CHECK
  hwmon: (aspeed-pwm-tacho) Deassert reset in probe
  dt-bindings: hwmon: aspeed-pwm-tacho: Add reset node
  hwmon: (pmbus) cffps: Add debugfs entries
  hwmon: (pmbus) Export pmbus device debugfs directory entry
  hwmon: (w83773g) Fix fault detection and reporting
  hwmon: (hih6130) Fix documentation of struct hih6130
  hwmon: (iio_hwmon) Fix documentation of struct iio_hwmon_state
  hwmon: (sht15) Fix parameter documentation of sht15_crc8()
  hwmon: (sht21) Fix documentation of struct sht21
  ...

Pull MTD updates from Boris Brezillon:
 "MTD core changes:
   - Rework core functions to avoid duplicating generic checks in
     NAND/OneNAND sub-layers
   - Update the MAINTAINERS entry to reflect the fact that MTD
     maintainers now use a single git tree

  MTD driver changes:
   - CFI: use macros instead of inline functions to limit stack usage
     and make KASAN happy

  NAND core changes:
   - Fix NAND_CMD_NONE handling in nand_command[_lp]() hooks
   - Introduce the ->exec_op() infrastructure
   - Rework NAND buffers handling
   - Fix ECC requirements for K9F4G08U0D
   - Fix nand_do_read_oob() to return the number of bitflips
   - Mark K9F1G08U0E as not supporting subpage writes

  NAND driver changes:
   - MTK: Rework the driver to support new IP versions
   - OMAP OneNAND: Full rework to use new APIs (libgpio, dmaengine) and
     fix DT support
   - Marvell: Add a new driver to replace the pxa3xx one

  SPI NOR core changes:
   - Add support to new ISSI and Cypress/Spansion memory parts.
   - Fix support of Micron memories by checking error bits in the FSR.
   - Fix update of block-protection bits by reading back the SR.
   - Restore the internal state of the SPI flash memory when removing
     the device.

  SPI NOR driver changes:
   - Maintenance for Freescale, Intel and Metiatek drivers.
   - Add support of the direct access mode for the Cadence QSPI
     controller"

* tag 'mtd/for-4.16' of git://git.infradead.org/linux-mtd: (93 commits)
  mtd: nand: sunxi: Fix ECC strength choice
  mtd: nand: gpmi: Fix subpage reads
  mtd: nand: Fix build issues due to an anonymous union
  mtd: nand: marvell: Fix missing memory allocation modifier
  mtd: nand: marvell: remove redundant variable 'oob_len'
  mtd: nand: marvell: fix spelling mistake: "suceed"-> "succeed"
  mtd: onenand: omap2: Remove redundant dev_err call in omap2_onenand_probe()
  mtd: Remove duplicate checks on mtd_oob_ops parameter
  mtd: Fallback to ->_read/write_oob() when ->_read/write() is missing
  mtd: mtdpart: Make ECC stat handling consistent
  mtd: onenand: omap2: print resource using %pR format string
  mtd: mtk-nor: modify functions' name more generally
  mtd: onenand: samsung: remove incorrect __iomem annotation
  MAINTAINERS: Add entry for Marvell NAND controller driver
  ARM: OMAP2+: Remove gpmc-onenand
  mtd: onenand: omap2: Configure driver from DT
  mtd: onenand: omap2: Decouple DMA enabling from INT pin availability
  mtd: onenand: omap2: Do not make delay for GPIO OMAP3 specific
  mtd: onenand: omap2: Convert to use dmaengine for memcpy
  mtd: onenand: omap2: Unify OMAP2 and OMAP3 DMA implementation
  ...

Pull backlight updates from Lee Jones:
 "Fix-ups:
   - Deprecate pci_get_bus_and_slot() in apple_bl

  Bug Fixes:
   - Enable Chip Select when conducting SPI transfers in corgi_lcd,
     tdo24m, tosa_lcd"

* tag 'for-backlight-next-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight:
  backlight: tdo24m: Fix the SPI CS between transfers
  backlight: apple_bl: Deprecate pci_get_bus_and_slot()

Pull MFD updates from Lee Jones:
 "New Drivers:
   - Add support for RAVE Supervisory Processor

  Moved drivers:
   - Move Realtek Card Reader Driver to Misc

  New Device Support:
   - Add support for Pinctrl to axp20x

  New Functionality:
   - Add resume support to atmel-flexcom

  Fix-ups:
   - Split MFD (mfd) and userspace handlers (platform) in cros_ec
   - Fix trivial (whitespace, spelling) issue(s) in pcf50633-core
   - Clean-up error handling in ab8500-debugfs
   - General tidying up in tmio_core
   - Kconfig fix-ups for qcom-pm8xxx
   - Licensing changes (SPDX) to stm32-lptimer, stm32-timers
   - Device Tree fixups in mc13xxx
   - Simplify/remove unused code in cros_ec_spi, axp20x, ti_am335x_tscadc,
     kempld-core, intel_soc_pmic_core.c, ab8500-debugfs"

* tag 'mfd-next-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (32 commits)
  mfd: lpc_ich: Do not touch SPI-NOR write protection bit on Apollo Lake
  mfd: axp20x: Mark axp288 CHRG_BAK_CTRL register volatile
  mfd: ab8500: Introduce DEFINE_SHOW_ATTRIBUTE() macro
  atmel_flexcom: Support resuming after a chip reset
  mfd: Remove duplicate includes
  dt-bindings: mfd: mc13xxx: Add the unit address to sysled
  mfd: stm32: Adopt SPDX identifier
  mfd: axp20x: Add pinctrl cell for AXP813
  mfd: pm8xxx: Make elegible for COMPILE_TEST
  mfd: kempld-core: Use resource_size function on resource object
  mfd: tmio: Move register macros to tmio_core.c
  mfd: cros ec: spi: Simplify delay handling between SPI messages
  mfd: palmas: Assign the right powerhold mask for tps65917
  mfd: ab8500-debugfs: Use common error handling code in ab8500_print_modem_registers()
  mfd: ti_am335x_tscadc: Remove redundant assignment to node
  mfd: pcf50633: Fix spelling mistake: 'Falied' -> 'Failed'
  dt-bindings: watchdog: Add bindings for RAVE SP watchdog driver
  watchdog: Add RAVE SP watchdog driver
  mfd: Add driver for RAVE Supervisory Processor
  serdev: Introduce devm_serdev_device_open()
  ...

Pull PNP updates from Rafael Wysocki:
 "These make pnpbios_thread_init() use PTR_ERR_OR_ZERO() and remove an
  unnecessary kallsyms include from drivers/pnp/quirks.c (Vasyl
  Gomonovych, Sergey Senozhatsky)"

* tag 'pnp-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  PNP: pnpbios: Use PTR_ERR_OR_ZERO()
  PNP: remove unneeded kallsyms include

Pull ACPI updates from Rafael Wysocki:
 "The majority of this is an update of the ACPICA kernel code to
  upstream revision 20171215 with a cosmetic change and a maintainers
  information update on top of it.

  The rest is mostly some minor fixes and cleanups in the ACPI drivers
  and cleanups to initialization on x86.

  Specifics:

   - Update the ACPICA kernel code to upstream revision 20171215 including:
      * Support for ACPI 6.0A changes in the NFIT table (Bob Moore)
      * Local 64-bit divide in string conversions (Bob Moore)
      * Fix for a regression in acpi_evaluate_object_type() (Bob Moore)
      * Fixes for memory leaks during package object resolution (Bob
        Moore)
      * Deployment of safe version of strncpy() (Bob Moore)
      * Debug and messaging updates (Bob Moore)
      * Support for PDTT, SDEV, TPM2 tables in iASL and tools (Bob
        Moore)
      * Null pointer dereference avoidance in Op and cleanups (Colin Ian
        King)
      * Fix for memory leak from building prefixed pathname (Erik
        Schmauss)
      * Coding style fixes, disassembler and compiler updates (Hanjun
        Guo, Erik Schmauss)
      * Additional PPTT flags from ACPI 6.2 (Jeremy Linton)
      * Fix for an off-by-one error in acpi_get_timer_duration()
        (Jung-uk Kim)
      * Infinite loop detection timeout and utilities cleanups (Lv
        Zheng)
      * Windows 10 version 1607 and 1703 OSI strings (Mario
        Limonciello)

   - Update ACPICA information in MAINTAINERS to reflect the current
     status of ACPICA maintenance and rename a local variable in one
     function to match the corresponding upstream code (Rafael Wysocki)

   - Clean up ACPI-related initialization on x86 (Andy Shevchenko)

   - Add support for Intel Merrifield to the ACPI GPIO code (Andy
     Shevchenko)

   - Clean up ACPI PMIC drivers (Andy Shevchenko, Arvind Yadav)

   - Fix the ACPI Generic Event Device (GED) driver to free IRQs on
     shutdown and clean up the PCI IRQ Link driver (Sinan Kaya)

   - Make the GHES code call into the AER driver on all errors and clean
     up the ACPI APEI code (Colin Ian King, Tyler Baicar)

   - Make the IA64 ACPI NUMA code parse all SRAT entries (Ganapatrao
     Kulkarni)

   - Add a lid switch blacklist to the ACPI button driver and make it
     print extra debug messages on lid events (Hans de Goede)

   - Add quirks for Asus GL502VSK and UX305LA to the ACPI battery driver
     and clean it up somewhat (Bjørn Mork, Kai-Heng Feng)

   - Add device link for CHT SD card dependency on I2C to the ACPI LPSS
     (Intel SoCs) driver and make it avoid creating platform device
     objects for devices without MMIO resources (Adrian Hunter, Hans de
     Goede)

   - Fix the ACPI GPE mask kernel command line parameter handling
     (Prarit Bhargava)

   - Fix the handling of (incorrectly exposed) backlight interfaces
     without LCD (Hans de Goede)

   - Fix the usage of debugfs_create_*() in the ACPI EC driver (Geert
     Uytterhoeven)"

* tag 'acpi-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (62 commits)
  ACPI/PCI: pci_link: reduce verbosity when IRQ is enabled
  ACPI / LPSS: Do not instiate platform_dev for devs without MMIO resources
  ACPI / PMIC: Convert to use builtin_platform_driver() macro
  ACPI / x86: boot: Propagate error code in acpi_gsi_to_irq()
  ACPICA: Update version to 20171215
  ACPICA: trivial style fix, no functional change
  ACPICA: Fix a couple memory leaks during package object resolution
  ACPICA: Recognize the Windows 10 version 1607 and 1703 OSI strings
  ACPICA: DT compiler: prevent error if optional field at the end of table is not present
  ACPICA: Rename a global variable, no functional change
  ACPICA: Create and deploy safe version of strncpy
  ACPICA: Cleanup the global variables and update comments
  ACPICA: Debugger: fix slight indentation issue
  ACPICA: Fix a regression in the acpi_evaluate_object_type() interface
  ACPICA: Update for a few debug output statements
  ACPICA: Debug output, no functional change
  ACPI: EC: Fix debugfs_create_*() usage
  ACPI / video: Default lcd_only to true on Win8-ready and newer machines
  ACPI / x86: boot: Don't setup SCI on HW-reduced platforms
  ACPI / x86: boot: Use INVALID_ACPI_IRQ instead of 0 for acpi_sci_override_gsi
  ...

Pull power management updates from Rafael Wysocki:
 "This includes some infrastructure changes in the PM core, mostly
  related to integration between runtime PM and system-wide suspend and
  hibernation, plus some driver changes depending on them and fixes for
  issues in that area which have become quite apparent recently.

  Also included are changes making more x86-based systems use the Low
  Power Sleep S0 _DSM interface by default, which turned out to be
  necessary to handle power button wakeups from suspend-to-idle on
  Surface Pro3.

  On the cpufreq front we have fixes and cleanups in the core, some new
  hardware support, driver updates and the removal of some unused code
  from the CPU cooling thermal driver.

  Apart from this, the Operating Performance Points (OPP) framework is
  prepared to be used with power domains in the future and there is a
  usual bunch of assorted fixes and cleanups.

  Specifics:

   - Define a PM driver flag allowing drivers to request that their
     devices be left in suspend after system-wide transitions to the
     working state if possible and add support for it to the PCI bus
     type and the ACPI PM domain (Rafael Wysocki).

   - Make the PM core carry out optimizations for devices with driver PM
     flags set in some cases and make a few drivers set those flags
     (Rafael Wysocki).

   - Fix and clean up wrapper routines allowing runtime PM device
     callbacks to be re-used for system-wide PM, change the generic
     power domains (genpd) framework to stop using those routines
     incorrectly and fix up a driver depending on that behavior of genpd
     (Rafael Wysocki, Ulf Hansson, Geert Uytterhoeven).

   - Fix and clean up the PM core's device wakeup framework and
     re-factor system-wide PM core code related to device wakeup
     (Rafael Wysocki, Ulf Hansson, Brian Norris).

   - Make more x86-based systems use the Low Power Sleep S0 _DSM
     interface by default (to fix power button wakeup from
     suspend-to-idle on Surface Pro3) and add a kernel command line
     switch to tell it to ignore the system sleep blacklist in the ACPI
     core (Rafael Wysocki).

   - Fix a race condition related to cpufreq governor module removal and
     clean up the governor management code in the cpufreq core (Rafael
     Wysocki).

   - Drop the unused generic code related to the handling of the static
     power energy usage model in the CPU cooling thermal driver along
     with the corresponding documentation (Viresh Kumar).

   - Add mt2712 support to the Mediatek cpufreq driver (Andrew-sh
     Cheng).

   - Add a new operating point to the imx6ul and imx6q cpufreq drivers
     and switch the latter to using clk_bulk_get() (Anson Huang, Dong
     Aisheng).

   - Add support for multiple regulators to the TI cpufreq driver along
     with a new DT binding related to that and clean up that driver
     somewhat (Dave Gerlach).

   - Fix a powernv cpufreq driver regression leading to incorrect CPU
     frequency reporting, fix that driver to deal with non-continguous
     P-states correctly and clean it up (Gautham Shenoy, Shilpasri
     Bhat).

   - Add support for frequency scaling on Armada 37xx SoCs through the
     generic DT cpufreq driver (Gregory CLEMENT).

   - Fix error code paths in the mvebu cpufreq driver (Gregory CLEMENT).

   - Fix a transition delay setting regression in the longhaul cpufreq
     driver (Viresh Kumar).

   - Add Skylake X (server) support to the intel_pstate cpufreq driver
     and clean up that driver somewhat (Srinivas Pandruvada).

   - Clean up the cpufreq statistics collection code (Viresh Kumar).

   - Drop cluster terminology and dependency on physical_package_id from
     the PSCI driver and drop dependency on arm_big_little from the SCPI
     cpufreq driver (Sudeep Holla).

   - Add support for system-wide suspend and resume to the RAPL power
     capping driver and drop a redundant semicolon from it (Zhen Han,
     Luis de Bethencourt).

   - Make SPI domain validation (in the SCSI SPI transport driver) and
     system-wide suspend mutually exclusive as they rely on the same
     underlying mechanism and cannot be carried out at the same time
     (Bart Van Assche).

   - Fix the computation of the amount of memory to preallocate in the
     hibernation core and clean up one function in there (Rainer Fiebig,
     Kyungsik Lee).

   - Prepare the Operating Performance Points (OPP) framework for being
     used with power domains and clean up one function in it (Viresh
     Kumar, Wei Yongjun).

   - Clean up the generic sysfs interface for device PM (Andy
     Shevchenko).

   - Fix several minor issues in power management frameworks and clean
     them up a bit (Arvind Yadav, Bjorn Andersson, Geert Uytterhoeven,
     Gustavo Silva, Julia Lawall, Luis de Bethencourt, Paul Gortmaker,
     Sergey Senozhatsky, gaurav jindal).

   - Make it easier to disable PM via Kconfig (Mark Brown).

   - Clean up the cpupower and intel_pstate_tracer utilities (Doug
     Smythies, Laura Abbott)"

* tag 'pm-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (89 commits)
  PCI / PM: Remove spurious semicolon
  cpufreq: scpi: remove arm_big_little dependency
  drivers: psci: remove cluster terminology and dependency on physical_package_id
  powercap: intel_rapl: Fix trailing semicolon
  dmaengine: rcar-dmac: Make DMAC reinit during system resume explicit
  PM / runtime: Allow no callbacks in pm_runtime_force_suspend|resume()
  PM / hibernate: Drop unused parameter of enough_swap
  PM / runtime: Check ignore_children in pm_runtime_need_not_resume()
  PM / runtime: Rework pm_runtime_force_suspend/resume()
  PM / genpd: Stop/start devices without pm_runtime_force_suspend/resume()
  cpufreq: powernv: Dont assume distinct pstate values for nominal and pmin
  cpufreq: intel_pstate: Add Skylake servers support
  cpufreq: intel_pstate: Replace bxt_funcs with core_funcs
  platform/x86: surfacepro3: Support for wakeup from suspend-to-idle
  ACPI / PM: Use Low Power S0 Idle on more systems
  PM / wakeup: Print warn if device gets enabled as wakeup source during sleep
  PM / domains: Don't skip driver's ->suspend|resume_noirq() callbacks
  PM / core: Propagate wakeup_path status flag in __device_suspend_late()
  PM / core: Re-structure code for clearing the direct_complete flag
  powercap: add suspend and resume mechanism for SOC power limit
  ...

Pull sound updates from Takashi Iwai:
 "The major changes in the core API side in this cycle are the still
  on-going ASoC componentization works. Other than that, only few small
  changes such as 20bit PCM format support are found.

  Meanwhile the rest majority of changes are for ASoC drivers:

   - Large cleanups of some of the TI CODEC drivers

   - Continued work on Intel ASoC stuff for new quirks, ACPI GPIO
     handling, Kconfigs and lots of cleanups

   - Refactoring of the Freescale SSI driver, as preliminary work for
     the upcoming changes

   - Work on ST DFSDM driver, including the required IIO patches

   - New drivers for Allwinner A83T, Maxim MAX89373, SocioNext UiniPhier
     EVEA Tempo Semiconductor TSCS42xx and TI PCM816x, TAS5722 and
     TAS6424 devices

   - Removal of dead codes for SN95031 and board drivers

  Last but not least, a few HD-audio and USB-audio quirks are included
  as usual, too"

* tag 'sound-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (303 commits)
  ALSA: hda - Reduce the suspend time consumption for ALC256
  ASoC: use seq_file to dump the contents of dai_list,platform_list and codec_list
  ASoC: soc-core: add missing EXPORT_SYMBOL_GPL() for snd_soc_rtdcom_lookup
  IIO: ADC: stm32-dfsdm: remove unused variable again
  ASoC: bcm2835: fix hw_params error when device is in prepared state
  ASoC: mxs-sgtl5000: Do not print error on probe deferral
  ASoC: sgtl5000: Do not print error on probe deferral
  ASoC: Intel: remove select on non-existing SND_SOC_INTEL_COMMON
  ALSA: usb-audio: Support changing input on Sound Blaster E1
  ASoC: Intel: remove second duplicated assignment to pointer 'res'
  ALSA: hda/realtek - update ALC215 depop optimize
  ALSA: hda/realtek - Support headset mode for ALC215/ALC285/ALC289
  ALSA: pcm: Fix trailing semicolon
  ASoC: add Component level .read/.write
  ASoC: cx20442: fix regression by adding back .read/.write
  ASoC: uda1380: fix regression by adding back .read/.write
  ASoC: tlv320dac33: fix regression by adding back .read/.write
  ALSA: hda - Use IS_REACHABLE() for dependency on input
  IIO: ADC: stm32-dfsdm: fix static check warning
  IIO: ADC: stm32-dfsdm: code optimization
  ...

Pull init_task initializer cleanups from David Howells:
 "It doesn't seem useful to have the init_task in a header file rather
  than in a normal source file. We could consolidate init_task handling
  instead and expand out various macros.

  Here's a series of patches that consolidate init_task handling:

   (1) Make THREAD_SIZE available to vmlinux.lds for cris, hexagon and
       openrisc.

   (2) Alter the INIT_TASK_DATA linker script macro to set
       init_thread_union and init_stack rather than defining these in C.

       Insert init_task and init_thread_into into the init_stack area in
       the linker script as appropriate to the configuration, with
       different section markers so that they end up correctly ordered.

       We can then get merge ia64's init_task.c into the main one.

       We then have a bunch of single-use INIT_*() macros that seem only
       to be macros because they used to be used per-arch. We can then
       expand these in place of the user and get rid of a few lines and
       a lot of backslashes.

   (3) Expand INIT_TASK() in place.

   (4) Expand in place various small INIT_*() macros that are defined
       conditionally. Expand them and surround them by #if[n]def/#endif
       in the .c file as it takes fewer lines.

   (5) Expand INIT_SIGNALS() and INIT_SIGHAND() in place.

   (6) Expand INIT_STRUCT_PID in place.

  These macros can then be discarded"

* tag 'init_task-20180117' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
  Expand INIT_STRUCT_PID and remove
  Expand the INIT_SIGNALS and INIT_SIGHAND macros and remove
  Expand various INIT_* macros and remove
  Expand INIT_TASK() in init/init_task.c and remove
  Construct init thread stack in the linker script rather than by union
  openrisc: Make THREAD_SIZE available to vmlinux.lds
  hexagon: Make THREAD_SIZE available to vmlinux.lds
  cris: Make THREAD_SIZE available to vmlinux.lds

Pull NAND changes from Boris Brezillon:

"
  Core changes:
  * Fix NAND_CMD_NONE handling in nand_command[_lp]() hooks
  * Introduce the ->exec_op() infrastructure
  * Rework NAND buffers handling
  * Fix ECC requirements for K9F4G08U0D
  * Fix nand_do_read_oob() to return the number of bitflips
  * Mark K9F1G08U0E as not supporting subpage writes

  Driver changes:
  * MTK: Rework the driver to support new IP versions
  * OMAP OneNAND: Full rework to use new APIs (libgpio, dmaengine) and fix
    DT support
  * Marvell: Add a new driver to replace the pxa3xx one
"

Pull spi-nor changes from Cyrille Pitchen:

"
  This pull-request contains the following notable changes:

  Core changes:
  * Add support to new ISSI and Cypress/Spansion memory parts.
  * Fix support of Micron memories by checking error bits in the FSR.
  * Fix update of block-protection bits by reading back the SR.
  * Restore the internal state of the SPI flash memory when removing the
    device.

  Driver changes:
  * Maintenance for Freescale, Intel and Metiatek drivers.
  * Add support of the direct access mode for the Cadence QSPI controller.
"

Pull x86 retpoline fixlet from Thomas Gleixner:
 "Remove the ESP/RSP thunks for retpoline as they cannot ever work.

  Get rid of them before they show up in a release"

* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/retpoline: Remove the esp/rsp thunk

Pull x86 fixes from Thomas Gleixner:
 "A set of small fixes for 4.15:

   - Fix vmapped stack synchronization on systems with 4-level paging
     and a large amount of memory caused by a missing 5-level folding
     which made the pgd synchronization logic to fail and causing double
     faults.

   - Add a missing sanity check in the vmalloc_fault() logic on 5-level
     paging systems.

   - Bring back protection against accessing a freed initrd in the
     microcode loader which was lost by a wrong merge conflict
     resolution.

   - Extend the Broadwell micro code loading sanity check.

   - Add a missing ENDPROC annotation in ftrace assembly code which
     makes ORC unhappy.

   - Prevent loading the AMD power module on !AMD platforms. The load
     itself is uncritical, but an unload attempt results in a kernel
     crash.

   - Update Peter Anvins role in the MAINTAINERS file"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/ftrace: Add one more ENDPROC annotation
  x86: Mark hpa as a "Designated Reviewer" for the time being
  x86/mm/64: Tighten up vmalloc_fault() sanity checks on 5-level kernels
  x86/mm/64: Fix vmapped stack syncing on very-large-memory 4-level systems
  x86/microcode: Fix again accessing initrd after having been freed
  x86/microcode/intel: Extend BDW late-loading further with LLC size check
  perf/x86/amd/power: Do not load AMD power module on !AMD platforms

Pull timer fix from Thomas Gleixner:
 "A single fix for a ~10 years old problem which causes high resolution
  timers to stop after a CPU unplug/plug cycle due to a stale flag in
  the per CPU hrtimer base struct.

  Paul McKenney was hunting this for about a year, but the heisenbug
  nature made it resistant against debug attempts for quite some time"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  hrtimer: Reset hrtimer cpu base proper on CPU hotplug

Pull scheduler fix from Thomas Gleixner:
 "A single bug fix to prevent a subtle deadlock in the scheduler core
  code vs cpu hotplug"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/core: Fix cpu.max vs. cpuhotplug deadlock

Pull perf fixes from Thomas Gleixner:
 "Four patches which all address lock inversions and deadlocks in the
  perf core code and the Intel debug store"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/x86: Fix perf,x86,cpuhp deadlock
  perf/core: Fix ctx::mutex deadlock
  perf/core: Fix another perf,trace,cpuhp lock inversion
  perf/core: Fix lock inversion between perf,trace,cpuhp

Pull locking fixes from Thomas Gleixner:
 "Two final locking fixes for 4.15:

   - Repair the OWNER_DIED logic in the futex code which got wreckaged
     with the recent fix for a subtle race condition.

   - Prevent the hard lockup detector from triggering when dumping all
     held locks in the system"

* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  locking/lockdep: Avoid triggering hardlockup from debug_show_all_locks()
  futex: Fix OWNER_DEAD fixup

When ORC support was added for the ftrace_64.S code, an ENDPROC
for function_hook() was missed. This results in the following warning:

  arch/x86/kernel/ftrace_64.o: warning: objtool: .entry.text+0x0: unreachable instruction

Fixes: e2ac83d7 ("x86/ftrace: Fix ORC unwinding from ftrace handlers")
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Reported-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://lkml.kernel.org/r/20180128022150.dqierscqmt3uwwsr@treble

Calling fan related SMM functions implemented by Dell BIOS firmware on Dell
Vostro 3360 freeze kernel for about 500ms.

Unfortunately, it is unlikely for Dell to fix this since the machine
is pretty old, so this commit just disables fan support to make the
system usable again.

Via "force" module param fan support can be enabled.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=195751
Link: http://lkml.iu.edu/hypermail/linux/kernel/1711.2/06083.htmlReviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Calling fan related SMM functions implemented by Dell BIOS firmware on Dell
Inspiron 7720 freeze kernel for about 500ms. Until Dell fixes it we need to
disable fan support for Dell Inspiron 7720 as it makes system unusable.

Via "force" module param fan support can be enabled.

Reported-by: vova7890@mail.ru
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=195751
Cc: stable@vger.kernel.org # v4.0+, will need backport
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Some Dell machines are broken and some functionality is disabled. Show
warning into dmesg about this fact and allow user via "force" module param
to override brokenness and enable broken functionality.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

The hrtimer interrupt code contains a hang detection and mitigation
mechanism, which prevents that a long delayed hrtimer interrupt causes a
continous retriggering of interrupts which prevent the system from making
progress. If a hang is detected then the timer hardware is programmed with
a certain delay into the future and a flag is set in the hrtimer cpu base
which prevents newly enqueued timers from reprogramming the timer hardware
prior to the chosen delay. The subsequent hrtimer interrupt after the delay
clears the flag and resumes normal operation.

If such a hang happens in the last hrtimer interrupt before a CPU is
unplugged then the hang_detected flag is set and stays that way when the
CPU is plugged in again. At that point the timer hardware is not armed and
it cannot be armed because the hang_detected flag is still active, so
nothing clears that flag. As a consequence the CPU does not receive hrtimer
interrupts and no timers expire on that CPU which results in RCU stalls and
other malfunctions.

Clear the flag along with some other less critical members of the hrtimer
cpu base to ensure starting from a clean state when a CPU is plugged in.

Thanks to Paul, Sebastian and Anna-Maria for their help to get down to the
root cause of that hard to reproduce heisenbug. Once understood it's
trivial and certainly justifies a brown paperbag.

Fixes: 41d2e494 ("hrtimer: Tune hrtimer_interrupt hang logic")
Reported-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Sewior <bigeasy@linutronix.de>
Cc: Anna-Maria Gleixner <anna-maria@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/alpine.DEB.2.20.1801261447590.2067@nanos

Due to some unfortunate events, I have not been directly involved in
the x86 kernel patch flow for a while now.  I have also not been able
to ramp back up by now like I had hoped to, and after reviewing what I
will need to work on both internally at Intel and elsewhere in the near
term, it is clear that I am not going to be able to ramp back up until
late 2018 at the very earliest.

It is not acceptable to not recognize that this load is currently
taken by Ingo and Thomas without my direct participation, so I mark
myself as R: (designated reviewer) rather than M: (maintainer) until
further notice.  This is in fact recognizing the de facto situation
for the past few years.

I have obviously no intention of going away, and I will do everything
within my power to improve Linux on x86 and x86 for Linux.  This,
however, puts credit where it is due and reflects a change of focus.

This patch also removes stale entries for portions of the x86
architecture which have not been maintained separately from arch/x86
for a long time.  If there is a reason to re-introduce them then that
can happen later.
Signed-off-by: H. Peter Anvin <h.peter.anvin@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Bruce Schlobohm <bruce.schlobohm@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20180125195934.5253-1-hpa@zytor.comSigned-off-by: Ingo Molnar <mingo@kernel.org>

Merge tag 'riscv-for-linus-4.15-maintainers' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux

Pull RISC-V update from Palmer Dabbelt:
 "RISC-V: We have a new mailing list and git repo!

  Sorry to send something essentially as late as possible (Friday after
  an rc9), but we managed to get a mailing list for the RISC-V Linux
  port. We've been using patches@groups.riscv.org for a while, but that
  list has some problems (it's Google Groups and it's shared over all
  RISC-V software projects). The new infaread.org list is much better.
  We just got it on Wednesday but I used it a bit on Thursday to shake
  out all the configuration problems and it appears to be in working
  order.

  When I updated the mailing list I noticed that the MAINTAINERS file
  was pointing to our github repo, but now that we have a kernel.org
  repo I'd like to point to that instead so I changed that as well.
  We'll be centralizing all RISC-V Linux related development here as
  that seems to be the saner way to go about it.

  I can understand if it's too late to get this into 4.15, but given
  that it's not a code change I was hoping it'd still be OK. It would be
  nice to have the new mailing list and git repo in the release tarballs
  so when people start to find bugs they'll get to the right place"

* tag 'riscv-for-linus-4.15-maintainers' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux:
  Update the RISC-V MAINTAINERS file

Merge remote-tracking branches 'spi/topic/pxa2xx', 'spi/topic/s3c64xx', 'spi/topic/sh-msiof', 'spi/topic/sirf' and 'spi/topic/sun6i' into spi-next

Merge remote-tracking branches 'spi/topic/fsl-dspi', 'spi/topic/imx', 'spi/topic/jcore', 'spi/topic/meson' and 'spi/topic/orion' into spi-next

Merge remote-tracking branches 'spi/topic/a3700', 'spi/topic/atmel', 'spi/topic/bcm53xx', 'spi/topic/davinci' and 'spi/topic/dw' into spi-next

Pull networking fixes from David Miller:

 1) The per-network-namespace loopback device, and thus its namespace,
    can have its teardown deferred for a long time if a kernel created
    TCP socket closes and the namespace is exiting meanwhile. The kernel
    keeps trying to finish the close sequence until it times out (which
    takes quite some time).

    Fix this by forcing the socket closed in this situation, from Dan
    Streetman.

 2) Fix regression where we're trying to invoke the update_pmtu method
    on route types (in this case metadata tunnel routes) that don't
    implement the dst_ops method. Fix from Nicolas Dichtel.

 3) Fix long standing memory corruption issues in r8169 driver by
    performing the chip statistics DMA programming more correctly. From
    Francois Romieu.

 4) Handle local broadcast sends over VRF routes properly, from David
    Ahern.

 5) Don't refire the DCCP CCID2 timer endlessly, otherwise the socket
    can never be released. From Alexey Kodanev.

 6) Set poll flags properly in VSOCK protocol layer, from Stefan
    Hajnoczi.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  VSOCK: set POLLOUT | POLLWRNORM for TCP_CLOSING
  dccp: don't restart ccid2_hc_tx_rto_expire() if sk in closed state
  net: vrf: Add support for sends to local broadcast address
  r8169: fix memory corruption on retrieval of hardware statistics.
  net: don't call update_pmtu unconditionally
  net: tcp: close sock if net namespace is exiting

Pull drm fixes from Dave Airlie:
 "A fairly urgent nouveau regression fix for broken irqs across
  suspend/resume came in. This was broken before but a patch in 4.15 has
  made it much more obviously broken and now s/r fails a lot more often.

  The fix removes freeing the irq across s/r which never should have
  been done anyways.

  Also two vc4 fixes for a NULL deference and some misrendering /
  flickering on screen"

* tag 'drm-fixes-for-v4.15-rc10-2' of git://people.freedesktop.org/~airlied/linux:
  drm/nouveau: Move irq setup/teardown to pci ctor/dtor
  drm/vc4: Fix NULL pointer dereference in vc4_save_hang_state()
  drm/vc4: Flush the caches before the bin jobs, as well.

select(2) with wfds but no rfds must return when the socket is shut down
by the peer.  This way userspace notices socket activity and gets -EPIPE
from the next write(2).

Currently select(2) does not return for virtio-vsock when a SEND+RCV
shutdown packet is received.  This is because vsock_poll() only sets
POLLOUT | POLLWRNORM for TCP_CLOSE, not the TCP_CLOSING state that the
socket is in when the shutdown is received.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ccid2_hc_tx_rto_expire() timer callback always restarts the timer
again and can run indefinitely (unless it is stopped outside), and after
commit 120e9dab ("dccp: defer ccid_hc_tx_delete() at dismantle time"),
which moved ccid_hc_tx_delete() (also includes sk_stop_timer()) from
dccp_destroy_sock() to sk_destruct(), this started to happen quite often.
The timer prevents releasing the socket, as a result, sk_destruct() won't
be called.

Found with LTP/dccp_ipsec tests running on the bonding device,
which later couldn't be unloaded after the tests were completed:

  unregister_netdevice: waiting for bond0 to become free. Usage count = 148

Fixes: 2a91aa39 ("[DCCP] CCID2: Initial CCID2 (TCP-Like) implementation")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now that we're upstream in Linux we've been able to make some
infrastructure changes so our port works a bit more like other ports.
Specifically:

* We now have a mailing list specific to the RISC-V Linux port, hosted
  at lists.infreadead.org.
* We now have a kernel.org git tree where work on our port is
  coordinated.

This patch changes the RISC-V maintainers entry to reflect these new
bits of infrastructure.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>

On a 5-level kernel, if a non-init mm has a top-level entry, it needs to
match init_mm's, but the vmalloc_fault() code skipped over the BUG_ON()
that would have checked it.

While we're at it, get rid of the rather confusing 4-level folded "pgd"
logic.

Cleans-up: b50858ce ("x86/mm/vmalloc: Add 5-level paging support")
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Neil Berrington <neil.berrington@datacore.com>
Link: https://lkml.kernel.org/r/2ae598f8c279b0a29baf75df207e6f2fdddc0a1b.1516914529.git.luto@kernel.org

Neil Berrington reported a double-fault on a VM with 768GB of RAM that uses
large amounts of vmalloc space with PTI enabled.

The cause is that load_new_mm_cr3() was never fixed to take the 5-level pgd
folding code into account, so, on a 4-level kernel, the pgd synchronization
logic compiles away to exactly nothing.

Interestingly, the problem doesn't trigger with nopti.  I assume this is
because the kernel is mapped with global pages if we boot with nopti.  The
sequence of operations when we create a new task is that we first load its
mm while still running on the old stack (which crashes if the old stack is
unmapped in the new mm unless the TLB saves us), then we call
prepare_switch_to(), and then we switch to the new stack.
prepare_switch_to() pokes the new stack directly, which will populate the
mapping through vmalloc_fault().  I assume that we're getting lucky on
non-PTI systems -- the old stack's TLB entry stays alive long enough to
make it all the way through prepare_switch_to() and switch_to() so that we
make it to a valid stack.

Fixes: b50858ce ("x86/mm/vmalloc: Add 5-level paging support")
Reported-and-tested-by: Neil Berrington <neil.berrington@datacore.com>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Cc: stable@vger.kernel.org
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Link: https://lkml.kernel.org/r/346541c56caed61abbe693d7d2742b4a380c5001.1516914529.git.luto@kernel.org

Local struct chip_data has two members that are not used:

- cs. Looks like was never used
- enable_dma. Became unused by the commit f89a6d8f ("spi: dw-mid: move
  to use core SPI DMA mappings").
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>