In SPI mode the transfer buffer is locked with a mutex. However this
mutex is only initilized after the probe, but some transfer needs to
be done in the probe.

To fix this bug we move the mutex initialization at the beginning of
the device probe.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Acked-by: Denis Ciocca <denis.ciocca@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

The VREFN channel is bipolar, not unipolar. Small negative values do
occur (e.g., -1mV), and unsigned conversion maps them incorrectly to
large positive values (about +1V), so fix this.
Signed-off-by: Thomas Betker <thomas.betker@rohde-schwarz.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

The scaling factor for VREFP is 3.0/4096, not 1.0/4096; fix this to get
correct readings.
Signed-off-by: Thomas Betker <thomas.betker@rohde-schwarz.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

For the "vccaux" channel, read the VCCAUX register, not VCCINT.
Signed-off-by: Thomas Betker <thomas.betker@rohde-schwarz.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Define the register addresses for MIN_VCCPINT, MIN_VCCPAUX, MIN_VCCO_DDR
correctly.
Signed-off-by: Thomas Betker <thomas.betker@rohde-schwarz.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Fix "null" in the raw attribute and scan elements.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Currently in_proximity_(null)_raw is getting presented as raw sysfs
attribute. Same with the scan_elements.
The modifier doesn't apply to this channel.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

With 'dx' equal to 0.625V and 15 bit ADC, calculations overflow
when difference against GND is ~20% of the ADC range. Fix this.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Commit 65de7654 ("iio: iio: Fix iio_channel_read return if
channel havn't info") added a check for valid info masks.

This patch adds missing channel info masks for all ADC channels.
Otherwise, iio_read_channel_raw() would return -EINVAL when called
by consumer drivers.

Note that the change of _processed to _raw actually fixes an ABI abuse
in the original driver where it was used to avoid some special handling
rather than because it was correct.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Temperature reads on bmp280 device always return 0,
due to a missing step in the compensation formula
(data->tfine is never initialized).

Initialize data->tfine value so we get correct
temperature and pressure values.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Reviewed-by: Vlad Dogaru <vlad.dogaru@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

We want those fixes (iio primarily) into the -next branch to help with
merge and testing issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull networking fixes from David Miller:

 1) In TCP, don't register an FRTO for cumulatively ACK'd data that was
    previously SACK'd, from Neal Cardwell.

 2) Need to hold RNL mutex in ipv4 multicast code namespace cleanup,
    from Cong WANG.

 3) Similarly we have to hold RNL mutex for fib_rules_unregister(), also
    from Cong WANG.

 4) Revert and rework netns nsid allocation fix, from Nicolas Dichtel.

 5) When we encapsulate for a tunnel device, skb->sk still points to the
    user socket.  So this leads to cases where we retraverse the
    ipv4/ipv6 output path with skb->sk being of some other address
    family (f.e. AF_PACKET).  This can cause things to crash since the
    ipv4 output path is dereferencing an AF_PACKET socket as if it were
    an ipv4 one.

    The short term fix for 'net' and -stable is to elide these socket
    checks once we've entered an encapsulation sequence by testing
    xmit_recursion.

    Longer term we have a better solution wherein we pass the tunnel's
    socket down through the output paths, but that is way too invasive
    for 'net' and -stable.

    From Hannes Frederic Sowa.

 6) l2tp_init() failure path forgets to unregister per-net ops, from
    Cong WANG.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  net/mlx4_core: Fix error message deprecation for ConnectX-2 cards
  net: dsa: fix filling routing table from OF description
  l2tp: unregister l2tp_net_ops on failure path
  mvneta: dont call mvneta_adjust_link() manually
  ipv6: protect skb->sk accesses from recursive dereference inside the stack
  netns: don't allocate an id for dead netns
  Revert "netns: don't clear nsid too early on removal"
  ip6mr: call del_timer_sync() in ip6mr_free_table()
  net: move fib_rules_unregister() under rtnl lock
  ipv4: take rtnl_lock and mark mrt table as freed on namespace cleanup
  tcp: fix FRTO undo on cumulative ACK of SACKed range
  xen-netfront: transmit fully GSO-sized packets

Commit 1daa4303 ("net/mlx4_core: Deprecate error message at
ConnectX-2 cards startup to debug") did the deprecation only for port 1
of the card. Need to deprecate for port 2 as well.

Fixes: 1daa4303 ("net/mlx4_core: Deprecate error message at ConnectX-2 cards startup to debug")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

According to description in 'include/net/dsa.h', in cascade switches
configurations where there are more than one interconnected devices,
'rtable' array in 'dsa_chip_data' structure is used to indicate which
port on this switch should be used to send packets to that are destined
for corresponding switch.

However, dsa_of_setup_routing_table() fills 'rtable' with port numbers
of the _target_ switch, but not current one.

This commit removes redundant devicetree parsing and adds needed port
number as a function argument. So dsa_of_setup_routing_table() now just
looks for target switch number by parsing parent of 'link' device node.

To remove possible misunderstandings with the way of determining target
switch number, a corresponding comment was added to the source code and
to the DSA device tree bindings documentation file.

This was tested on a custom board with two Marvell 88E6095 switches with
following corresponding routing tables: { -1, 10 } and { 8, -1 }.
Signed-off-by: Pavel Nakonechny <pavel.nakonechny@skitlab.ru>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull input fixes from Dmitry Torokhov:
 "Updates for the input subsystem - two more tweaks for ALPS driver to
  work out kinks after splitting the touchpad, trackstick, and potential
  external PS/2 mouse into separate input devices.

  Changes to support ALPS SS4 devices (protocol V8) will be coming in
  4.1..."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: alps - document stick behavior for protocol V2
  Input: alps - report V2 Dualpoint Stick events via the right evdev node
  Input: alps - report interleaved bare PS/2 packets via dev3

Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mvneta_adjust_link() is a callback for of_phy_connect() and should
not be called directly. The result of calling it directly is as below:
Signed-off-by: David S. Miller <davem@davemloft.net>

We should not consult skb->sk for output decisions in xmit recursion
levels > 0 in the stack. Otherwise local socket settings could influence
the result of e.g. tunnel encapsulation process.

ipv6 does not conform with this in three places:

1) ip6_fragment: we do consult ipv6_npinfo for frag_size

2) sk_mc_loop in ipv6 uses skb->sk and checks if we should
   loop the packet back to the local socket

3) ip6_skb_dst_mtu could query the settings from the user socket and
   force a wrong MTU

Furthermore:
In sk_mc_loop we could potentially land in WARN_ON(1) if we use a
PF_PACKET socket ontop of an IPv6-backed vxlan device.

Reuse xmit_recursion as we are currently only interested in protecting
tunnel devices.

Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Document that protocol V2 uses standard (bare) PS/2 mouse packets for the
DualPoint stick.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-By: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

On V2 devices the DualPoint Stick reports bare packets, these should be
reported via the "AlpsPS/2 ALPS DualPoint Stick" dev2 evdev node, which also
has the INPUT_PROP_POINTING_STICK propbit set.

Note that since there is no way to distinguish these packets from an external
PS/2 mouse (insofar as these laptops have an external PS/2 port) this means
that we will be reporting PS/2 mouse events via this evdev node too, as we've
been doing in kernel 3.19 and older.

This has been tested on a Dell Latitude D620 and a Dell Latitude E6400,
which both have a V2 touchpad + a DualPoint Stick which reports bare packets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Bare packets should be reported via the same evdev device independent on
whether they are detected on the beginning of a packet or in the middle
of a packet.

This has been tested on a Dell Latitude E6400, where the DualPoint Stick
reports bare packets, which get reported via dev3 when the touchpad is
idle, and via dev2 when the touchpad and stick are used simultaneously.

This commit fixes this inconsistency by always reporting bare packets via
dev3. Note that since the come from a DualPoint Stick they really should be
reported via dev2, this gets fixed in a later commit.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Orthography and coding style corrections.
Signed-off-by: Amaury Bouchra Pilet <Amaury.Bouchra.Pilet@ENS.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Return a negative error code on failure.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
 { ... return ret; }
|
ret = 0
)
... when != ret = e1
    when != &ret
*if(...)
{
  ... when != ret = e2
      when forall
 return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Sparse reports:

drivers/staging/lustre/lustre/obdclass/obd_mount.c:1284:6: warning:
 symbol 'lustre_kill_super' was not declared. Should it be static?

Fix this warning by making lustre_kill_super static.
It is not used outside this file.
Signed-off-by: Tal Shorer <tal.shorer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull USB fixes from Greg KH:
 "Here are some small USB fixes and new device ids for 4.0-rc6.  Nothing
  major, some xhci fixes for reported problems, and some usb-serial
  device ids.

  All have been in linux-next for a while"

* tag 'usb-4.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  USB: ftdi_sio: Use jtag quirk for SNAP Connect E10
  usb: isp1760: fix spin unlock in the error path of isp1760_udc_start
  usb: xhci: apply XHCI_AVOID_BEI quirk to all Intel xHCI controllers
  usb: xhci: handle Config Error Change (CEC) in xhci driver
  USB: keyspan_pda: add new device id
  USB: ftdi_sio: Added custom PID for Synapse Wireless product

Pull staging driver fixes from Greg KH:
 "Here are some staging driver fixes, well, really all just IIO driver
  fixes, for 4.0-rc6.  They fix issues that have been reported with
  these drivers.

  All of these patches have been in linux-next for a while"

* tag 'staging-4.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  iio: imu: Use iio_trigger_get for indio_dev->trig assignment
  iio: adc: vf610: use ADC clock within specification
  iio/adc/cc10001_adc.c: Fix !HAS_IOMEM build
  iio: core: Fix double free.
  iio:inv-mpu6050: Fix inconsistency for the scale channel
  staging: iio: dummy: Fix undefined symbol build error
  iio: inv_mpu6050: Clear timestamps fifo while resetting hardware fifo
  staging: iio: hmc5843: Set iio name property in sysfs
  iio: bmc150: change sampling frequency
  iio: fix drivers that check buffer->scan_mask

Pull tty/serial fixes from Greg KH:
 "Here are 3 serial driver fixes for 4.0-rc6.  They fix some reported
  issues with the samsung and fsl_lpuart drivers.

  All have been in linux-next for a while"

* tag 'tty-4.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  tty: serial: fsl_lpuart: clear receive flag on FIFO flush
  tty: serial: fsl_lpuart: specify transmit FIFO size
  serial: samsung: Clear operation mode on UART shutdown

This reverts commit 6ad6b5ed.

It added a file that should not be in the kernel source tree.

Cc: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull input subsystem fixes from Dmitry Torokhov:
 "A fix for ALPS driver for issue introduced in the latest update and a
  tweak for yet another Lenovo box in Synaptics.

  There will be more ALPS tweaks coming.."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: define INPUT_PROP_ACCELEROMETER behavior
  Input: synaptics - fix min-max quirk value for E440
  Input: synaptics - add quirk for Thinkpad E440
  Input: ALPS - fix max coordinates for v5 and v7 protocols
  Input: add MT_TOOL_PALM

Pull block layer fix from Jens Axboe:
 "Just one patch in this pull request, fixing a regression caused by a
  'mathematically correct' change to lcm()"

* 'for-linus' of git://git.kernel.dk/linux-block:
  block: fix blk_stack_limits() regression due to lcm() change

Pull x86 fixes from Ingo Molnar:
 "Misc fixes: a SYSRET single-stepping fix, a dmi-scan robustization
  fix, a reboot quirk and a kgdb fixlet"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  kgdb/x86: Fix reporting of 'si' in kgdb on x86_64
  x86/asm/entry/64: Disable opportunistic SYSRET if regs->flags has TF set
  x86/reboot: Add ASRock Q1900DC-ITX mainboard reboot quirk
  MAINTAINERS: Change the x86 microcode loader maintainer
  firmware: dmi_scan: Prevent dmi_num integer overflow

Pull perf fixes from Ingo Molnar:
 "Two x86 Intel PMU constraint handling fixes"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/x86/intel: Fix Haswell CYCLE_ACTIVITY.* counter constraints
  perf/x86/intel: Filter branches for PEBS event

Pull devicetree fix from Grant Likely:
 "Simple bugfix for bad device tree data on the PA-Semi platform"

* tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux:
  drivers/of: Add empty ranges quirk for PA-Semi

Pull CIFS fixes from Steve French:
 "A set of small cifs fixes fixing a memory leak, kernel oops, and
  infinite loop (and some spotted by Coverity)"

* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
  Fix warning
  Fix another dereference before null check warning
  CIFS: session servername can't be null
  Fix warning on impossible comparison
  Fix coverity warning
  Fix dereference before null check warning
  Don't ignore errors on encrypting password in SMBTcon
  Fix warning on uninitialized buftype
  cifs: potential memory leaks when parsing mnt opts
  cifs: fix use-after-free bug in find_writable_file
  cifs: smb2_clone_range() - exit on unhandled error

First, let's explain the problem.
Suppose you have an ipip interface that stands in the netns foo and its link
part in the netns bar (so the netns bar has an nsid into the netns foo).
Now, you remove the netns bar:
 - the bar nsid into the netns foo is removed
 - the netns exit method of ipip is called, thus our ipip iface is removed:
   => a netlink message is built in the netns foo to advertise this deletion
   => this netlink message requests an nsid for bar, thus a new nsid is
      allocated for bar and never removed.

This patch adds a check in peernet2id() so that an id cannot be allocated for
a netns which is currently destroyed.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts
commit 4217291e ("netns: don't clear nsid too early on removal").

This is not the right fix, it introduces races.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is supposed to be ->rates_ex[] instead of ->rates[].  I found this
because static checkers complain than ->rates is too small so we're
reading beyond the end of the array.  It has 12 elements instead of 15.

This bug was apparently copy and pasted from ipw2x00.  I fixed it before
in that driver 428e3cf5 ('ipw2x00: printing the wrong array in
debug code')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove commented-out code
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

- Multiline comments use "network subsystem comment style"
- Merge short multiline comments
- Remove empty comments
- Remove function name comment at the end of small (<1 screen) functions
- Reformat 802.11 data frame format to use spaces and network format
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>