Some definitions at the beginning of this file were wrongly
indented: fix the indentation for all of these and, while at
it, also move the MTK_SPI_IDLE and MTK_SPI_PAUSED down, as to
implicitly group the hardware related definitions to the
software (driver) related ones.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220407114428.167091-9-angelogioacchino.delregno@collabora.comSigned-off-by: Mark Brown <broonie@kernel.org>

One of the two structures was already partially documented, but not
in kerneldoc format: enhance readability by adding the missing
documentation bits and use kerneldoc.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220407114428.167091-8-angelogioacchino.delregno@collabora.comSigned-off-by: Mark Brown <broonie@kernel.org>

Switch to dev_err_probe() to remove all dev_err() -> return repeated
patterns, simplifying and shortening the probe function.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220407114428.167091-7-angelogioacchino.delregno@collabora.comSigned-off-by: Mark Brown <broonie@kernel.org>

The last goto in the probe function can be removed by calling
pm_runtime_enable() right before devm_spi_register_master(), as
only some init checks were being performed after enabling pm.
This is a cleanup and brings no functional changes.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220407114428.167091-6-angelogioacchino.delregno@collabora.comSigned-off-by: Mark Brown <broonie@kernel.org>

Reparenting sel_clk to parent_clk can be done before enabling any of
spi_clk and spi_hclk. Move the call to clk_set_parent() for sel_clk
earlier, and call disable_unprepare() upon spi_clk prepare_enable()
failure to remove all clock disablement related gotos.
This commit is in preparation of a later cleanup.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220407114428.167091-5-angelogioacchino.delregno@collabora.comSigned-off-by: Mark Brown <broonie@kernel.org>

In preparation for switching to dev_err_probe() in this function, add
a pointer to struct device and replace all occurrences of '&pdev->dev'
to using this 'dev' pointer.
This is done for one-line fitting of the dev_err_probe() calls.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220407114428.167091-4-angelogioacchino.delregno@collabora.comSigned-off-by: Mark Brown <broonie@kernel.org>

Instead of performing yet another match check in the probe function,
simply switch to device_get_match_data().
This is a cleanup and brings no functional change.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220407114428.167091-3-angelogioacchino.delregno@collabora.comSigned-off-by: Mark Brown <broonie@kernel.org>

Switch to the devm variant of spi_alloc_master() to save some gotos.
This patch is a cleanup that brings no functional changes.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220407114428.167091-2-angelogioacchino.delregno@collabora.comSigned-off-by: Mark Brown <broonie@kernel.org>

The previous commit that made bits-per-word validation conditional
results in leaving no unconditional affectation of the status variable.

Since the variable is returned at the end of the function, initialize
it to avoid returning an undefined value.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Fixes: b3fe2e51 ("spi: core: Only check bits_per_word validity when explicitly provided")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20220414084040.975520-1-paul.kocialkowski@bootlin.comSigned-off-by: Mark Brown <broonie@kernel.org>

Pull in Atmel fix series, only first patch of which is for Linus
Signed-off-by: Mark Brown <broonie@kernel.org>

Remove the DTR checks as they are already handled in
spi_mem_default_supports_op(). This code removal was intentionally not done
in the previous patch that introduced the use of the
spi_mem_default_supports_op() core helper and fixed the buswidth adjustment
between SPIMEM and the SPI controller, so that the fix can be easily
backported to stable kernels.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20220406133604.455356-2-tudor.ambarus@microchip.comSigned-off-by: Mark Brown <broonie@kernel.org>

Use the spi_mem_default_supports_op() core helper in order to take into
account the buswidth specified by the user in device tree.

Cc: <stable@vger.kernel.org>
Fixes: 0e6aae08 ("spi: Add QuadSPI driver for Atmel SAMA5D2")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20220406133604.455356-1-tudor.ambarus@microchip.comSigned-off-by: Mark Brown <broonie@kernel.org>

Since the conversion to spi-mem, the driver advertised support for
various operations that cqspi_set_protocol() was never expected to handle
correctly - in particuar all non-DTR operations with command or address
buswidth > 1. For DTR, all operations except for 8-8-8 would fail, as
cqspi_set_protocol() returns -EINVAL.

In non-DTR mode, this resulted in data corruption for SPI-NOR flashes that
support such operations. As a minimal fix that can be backported to stable
kernels, simply disallow the unsupported operations again to avoid this
issue.

Fixes: a314f636 ("mtd: spi-nor: Convert cadence-quadspi to use spi-mem framework")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20220406132832.199777-1-matthias.schiffer@ew.tq-group.comSigned-off-by: Mark Brown <broonie@kernel.org>

Intel Raptor Lake-S has the same SPI serial flash controller as Alder
Lake-P. Add Raptor Lake-S PCI ID to the driver list of supported
devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20220411112116.53281-1-mika.westerberg@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

After system resumes, the registers of nor controller are
initialized with default values. The nor controller will
not function properly.

To handle both issues above, we add mtk_nor_init() in
mtk_nor_resume after pm_runtime_force_resume().

Fixes: 3bfd9103 ("spi: spi-mtk-nor: Add power management support")
Signed-off-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Link: https://lore.kernel.org/r/20220412115743.22641-1-allen-kh.cheng@mediatek.comSigned-off-by: Mark Brown <broonie@kernel.org>

The direction field in the DMA config is deprecated. The rspi driver
sets {src,dst}_{addr,addr_width} based on the DMA direction and
it results in dmaengine_slave_config() failure as RZ DMAC driver
validates {src,dst}_addr_width values independent of DMA direction.

This patch fixes the issue by passing both {src,dst}_{addr,addr_width}
values independent of DMA direction.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Suggested-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20220411173115.6619-1-biju.das.jz@bp.renesas.comSigned-off-by: Mark Brown <broonie@kernel.org>

On SPI device probe, the core will call spi_setup in spi_add_device
before the corresponding driver was probed. When this happens, the
bits_per_word member of the device is not yet set by the driver,
resulting in the default being set to 8 bits-per-word.

However some controllers do not support 8 bits-per-word at all, which
results in a failure when checking the bits-per-word validity.

In order to support these devices, skip the bits-per-word validity
check when it is not explicitly provided by drivers.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Link: https://lore.kernel.org/r/20220412122207.130181-1-paul.kocialkowski@bootlin.comSigned-off-by: Mark Brown <broonie@kernel.org>

Using pm_runtime_resume_and_get is more appropriate
for simplifing code
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Link: https://lore.kernel.org/r/20220412070906.2532091-1-chi.minghao@zte.com.cnSigned-off-by: Mark Brown <broonie@kernel.org>

wait_for_completion_timeout() returns unsigned long not int.
It returns 0 if timed out, and positive if completed.
The check for <= 0 is ambiguous and should be == 0 here
indicating timeout which is the only error case.

Fixes: 5720ec0a ("spi: spi-ti-qspi: Add DMA support for QSPI mmap read")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220411111034.24447-1-linmq006@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

Kernel function name don't match with function name.

Error log:
drivers/spi/spi-cadence.c:661: warning: expecting prototype for
cdns_spi_runtime_resume(). Prototype was for cnds_runtime_resume() instead
drivers/spi/spi-cadence.c:690: warning: expecting prototype for
cdns_spi_runtime_suspend(). Prototype was for cnds_runtime_suspend()
instead

Fixes: d36ccd9f ("spi: cadence: Runtime pm adaptation")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Link: https://lore.kernel.org/r/20220322150018.12736-1-amit.kumar-mahapatra@xilinx.comSigned-off-by: Mark Brown <broonie@kernel.org>

This fixes case where MSPI controller is used to access spi-nor
flash and BSPI block is not present.

Fixes: 5f195ee7 ("spi: bcm-qspi: Implement the spi_mem interface")
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220328142442.7553-1-kdasu.kdev@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

cqspi_set_protocol() only set the data width, but ignored the command
and address width (except for 8-8-8 DTR ops), leading to corruption of
all transfers using 1-X-X or X-X-X ops. Fix by setting the other two
widths as well.

While we're at it, simplify the code a bit by replacing the
CQSPI_INST_TYPE_* constants with ilog2().

Tested on a TI AM64x with a Macronix MX25U51245G QSPI flash with 1-4-4
read and write operations.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20220331110819.133392-1-matthias.schiffer@ew.tq-group.comSigned-off-by: Mark Brown <broonie@kernel.org>

Commit b470e10e ("spi: core: add dma_map_dev for dma device") added
dma_map_dev for _spi_map_msg() but missed to add for unmap routine,
__spi_unmap_msg(), so add it now.

Fixes: b470e10e ("spi: core: add dma_map_dev for dma device")
Cc: stable@vger.kernel.org # v5.14+
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20220406132238.1029249-1-vkoul@kernel.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Merge series from Leilk Liu <leilk.liu@mediatek.com>:

This series of patches are based on spi for-next, and provide 3 patches
to support MT7986.

To move the list iterator variable into the list_for_each_entry_*()
macro in the future it should be avoided to use the list iterator
variable after the loop body.

To *never* use the list iterator variable after the loop it was
concluded to use a separate iterator variable instead of a
found boolean [1].

This removes the need to use a found variable and simply checking if
the variable was set, can determine if the break/goto was hit.

Link: https://lore.kernel.org/all/CAHk-=wgRr_D8CB-D9Kg-c=EHreAsk5SqXPwr9Y7k9sA6cWXJ6w@mail.gmail.com/Signed-off-by: Jakob Koschel <jakobkoschel@gmail.com>
Link: https://lore.kernel.org/r/20220324072534.63420-1-jakobkoschel@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

powerpc's asm/prom.h brings some headers that it doesn't
need itself.

In order to clean it up, first add missing headers in
users of asm/prom.h
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/5ed3298d8b5b1b5bf681d79584c61cb495852f4e.1648833423.git.christophe.leroy@csgroup.euSigned-off-by: Mark Brown <broonie@kernel.org>

Add minItems constraint to interconnect-names as well. The schema
currently tries to match 2 names and fail for DTs with single entry.

With the change applied, below interconnect-names values are possible:
['qspi-config'], ['qspi-config', 'qspi-memory']

Fixes: 8f9c2915 ("dt-bindings: spi: Add interconnect binding for QSPI")
Signed-off-by: Kuldeep Singh <singh.kuldeep87k@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220328192006.18523-1-singh.kuldeep87k@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

Instead of calling the OF specific APIs, use device property ones.

It also prevents misusing PRP0001 in ACPI when trying to instantiate
spidev directly. We only support special SPI test devices there.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220323140215.2568-4-andriy.shevchenko@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Instead of calling the ACPI specific APIs, use device_get_match_data().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220323140215.2568-3-andriy.shevchenko@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

static_assert() is a preferred method to fail build when the certain
constraints are not met. Convert BUILD_BUG_ON() to static_assert().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220323140215.2568-2-andriy.shevchenko@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

this patch support hclk for AHB bus.
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220321013922.24067-3-leilk.liu@mediatek.comSigned-off-by: Mark Brown <broonie@kernel.org>

this patch adds hclk support.
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220321013922.24067-4-leilk.liu@mediatek.comSigned-off-by: Mark Brown <broonie@kernel.org>

this patch add the support of spi-mem for ipm design.
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220321013922.24067-2-leilk.liu@mediatek.comSigned-off-by: Mark Brown <broonie@kernel.org>

If spi_register_master() fails, we must undo a previous
mxic_spi_mem_ecc_probe() call, as already done in the remove function.

Fixes: 00360eba ("spi: mxic: Add support for pipelined ECC operations")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/09c81f751241f6ec0bac7a48d4ec814a742e0d17.1648980664.git.christophe.jaillet@wanadoo.frSigned-off-by: Mark Brown <broonie@kernel.org>

If rpcif_hw_init() fails, Runtime PM is left enabled.

Fixes: b04cc0d9 ("memory: renesas-rpc-if: Add support for RZ/G2L")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/1c78a1f447d019bb66b6e7787f520ae78821e2ae.1648562287.git.geert+renesas@glider.beSigned-off-by: Mark Brown <broonie@kernel.org>

Pull more tracing updates from Steven Rostedt:

 - Rename the staging files to give them some meaning. Just
   stage1,stag2,etc, does not show what they are for

 - Check for NULL from allocation in bootconfig

 - Hold event mutex for dyn_event call in user events

 - Mark user events to broken (to work on the API)

 - Remove eBPF updates from user events

 - Remove user events from uapi header to keep it from being installed.

 - Move ftrace_graph_is_dead() into inline as it is called from hot
   paths and also convert it into a static branch.

* tag 'trace-v5.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  tracing: Move user_events.h temporarily out of include/uapi
  ftrace: Make ftrace_graph_is_dead() a static branch
  tracing: Set user_events to BROKEN
  tracing/user_events: Remove eBPF interfaces
  tracing/user_events: Hold event_mutex during dyn_event_add
  proc: bootconfig: Add null pointer check
  tracing: Rename the staging files for trace_events

Pull clk fix from Stephen Boyd:
 "A single revert to fix a boot regression seen when clk_put() started
  dropping rate range requests. It's best to keep various systems
  booting so we'll kick this out and try again next time"

* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
  Revert "clk: Drop the rate range on clk_put()"

Pull x86 fixes from Thomas Gleixner:
 "A set of x86 fixes and updates:

   - Make the prctl() for enabling dynamic XSTATE components correct so
     it adds the newly requested feature to the permission bitmap
     instead of overwriting it. Add a selftest which validates that.

   - Unroll string MMIO for encrypted SEV guests as the hypervisor
     cannot emulate it.

   - Handle supervisor states correctly in the FPU/XSTATE code so it
     takes the feature set of the fpstate buffer into account. The
     feature sets can differ between host and guest buffers. Guest
     buffers do not contain supervisor states. So far this was not an
     issue, but with enabling PASID it needs to be handled in the buffer
     offset calculation and in the permission bitmaps.

   - Avoid a gazillion of repeated CPUID invocations in by caching the
     values early in the FPU/XSTATE code.

   - Enable CONFIG_WERROR in x86 defconfig.

   - Make the X86 defconfigs more useful by adapting them to Y2022
     reality"

* tag 'x86-urgent-2022-04-03' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/fpu/xstate: Consolidate size calculations
  x86/fpu/xstate: Handle supervisor states in XSTATE permissions
  x86/fpu/xsave: Handle compacted offsets correctly with supervisor states
  x86/fpu: Cache xfeature flags from CPUID
  x86/fpu/xsave: Initialize offset/size cache early
  x86/fpu: Remove unused supervisor only offsets
  x86/fpu: Remove redundant XCOMP_BV initialization
  x86/sev: Unroll string mmio with CC_ATTR_GUEST_UNROLL_STRING_IO
  x86/config: Make the x86 defconfigs a bit more usable
  x86/defconfig: Enable WERROR
  selftests/x86/amx: Update the ARCH_REQ_XCOMP_PERM test
  x86/fpu/xstate: Fix the ARCH_REQ_XCOMP_PERM implementation

Pull RT signal fix from Thomas Gleixner:
 "Revert the RT related signal changes. They need to be reworked and
  generalized"

* tag 'core-urgent-2022-04-03' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  Revert "signal, x86: Delay calling signals in atomic on RT enabled kernels"