Some adt7473 can't manage the 20µs delay we use for the bitbanging, bumping
it to 40µs seem to do the trick.
Signed-off-by: Martin Peres <martin.peres@free.fr>
Tested-by: Marcel Dopita <mdop@seznam.cz>

I spent some time this weekend trying to find in the vbios the number of
pulses per revolutions in the vbios but couldn't find it. It would seem
all my cards have 2 pulses per revolution so let's stick to that until
further notice.

Thermal table's id 0x48 may indicate this information but it would seem
that changing the value results in the blob power or clock gating the
RPM counter... We should ask NVIDIA about that, should be trivial-enough
for them to answer.
Signed-off-by: Martin Peres <martin.peres@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Only tested on nvf1, was advised to enable on all.
Signed-off-by: John Rowley <john.rowley08@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Signed-off-by: John Rowley <john.rowley08@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Set the correct subdev/engine classes when GK20A (0xea) is probed.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Add a GR device for GK20A based on NVE4, with the correct classes
definitions (GK20A's 3D class is 0xa297).

Most of the NVE4 code can be used on GK20A, so make relevant bits of
NVE4 available to other chips as well.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Pad the microcode to a multiple of 0x40 words, otherwise firmware will
fail to run from non-prepadded firmware files.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

nvc0_graph_ctor() would only let the graphics engine be enabled if its
oclass has a proper microcode linked to it. This prevents GR from being
enabled at all on chips that rely exclusively on external firmware, even
though such a use-case is valid.

Relax the conditions enabling the GR engine to also include the case
where an external firmware has also been loaded.

Also switch to external firmware if the graph class has no microcode
linked to it.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

GK20A's FIFO is compatible with NVE0, but only features 128 channels and
1 runlist.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Add a simple FB device for GK20A, as well as a RAM implementation
suitable for chips that use system memory as video RAM.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Add support for initializing the priv ring of GK20A. This is done by the
BIOS on desktop GPUs, but needs to be done by hand on Tegra.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Adapt the NVC0 BAR driver to make it able to support chips that do not
expose a BAR3. When this happens, BAR1 is then used for USERD mapping
and the BAR alloc() functions is disabled, making GPU objects unable
to rely on BAR for data access and falling back to PRAMIN.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Some chips that use system memory exclusively (e.g. GK20A) do not
expose 2 BAR regions. For them only BAR1 exists, and it should be used
for USERD mapping. Do not map BAR3 if its resource does not exist.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm/panel: Changes for v3.16-rc1

This set of commits contains a couple of fixes to existing panel drivers
and support for some new panels.

One commit touches the DRM core in that in modifies the MIPI DSI support
to hook up the shutdown function so that drivers can provide code that's
run on shutdown. This is used by a subsequent commit to make the simple
panel driver power off the backlight on shutdown.

* tag 'drm/panel/for-3.16-rc1' of git://anongit.freedesktop.org/tegra/linux:
  drm/panel: simple - Add AUO B133XTN01 panel support
  drm/panel: simple - Disable panel on shutdown
  drm/panel: add support for EDT ET057090DHU panel
  drm/panel: Add support for EDT ETM0700G0DH6 and ET070080DH6 panels
  drm/panel: ld9040: add power control sequence
  drm/panel: s6e8aa0: silence array overflow warning
  drm/dsi: Support device shutdown

drm/tegra: Changes for v3.16-rc1

The majority of these changes are a slew of cleanups across the board.
A more noteworthy change is the addition of drm_dev_set_unique() and the
conversion of the Tegra DRM driver to use it. This allows us to get rid
of the host1x drm_bus implementation. Other USB and platform drivers can
be changed in a similar way. Unfortunately for most PCI devices there is
some userspace that relies on the old functionality and cannot be as
easily converted.

HDMI and hardware cursor support is added for Tegra124. The SOR output
gains support for exposing CRCs via debugfs, which can be used for
automated testing. Many values that were hardcoded in the SOR/eDP code
are now computed at runtime to increase compatibility with more devices.

* tag 'drm/tegra/for-3.16-rc1' of git://anongit.freedesktop.org/tegra/linux: (47 commits)
  drm/tegra: sor - Remove obsolete comment
  drm/tegra: sor - Enable only the necessary number of lanes
  drm/tegra: sor - Power on only the necessary lanes
  drm/tegra: sor - Do not program interlaced mode registers
  drm/tegra: sor - Do not hardcode link speed
  drm/tegra: sor - Do not hardcode number of blank symbols
  drm/tegra: sor - Don't hardcode link parameters
  drm/tegra: sor - Change power down ordering
  drm/tegra: sor - Fix copy/paste error
  drm/tegra: sor - Remove pixel clock rounding
  drm/tegra: sor - Make debugfs setup consistent
  drm/tegra: sor - Recursively remove debugfs tree
  drm/tegra: dp - Mark the connector as hotplug capable
  drm/tegra: dp - Implement hotplug detection in work queue
  drm/tegra: Add hardware cursor support
  drm/tegra: Remove host1x drm_bus implementation
  drm: Document how to register devices without struct drm_bus
  drm: Add device registration documentation
  drm: Introduce drm_dev_set_unique()
  gpu: host1x: Rename internal functions for clarity
  ...

This panel is used by nyan-big and can be supported by the simple-panel
driver.
Signed-off-by: Stéphane Marchesin <marcheu@chromium.org>
[treding@nvidia.com: add device tree binding document]
Signed-off-by: Thierry Reding <treding@nvidia.com>

According to the DP specification the disparity of the first symbol
should always be negative. It is therefore safe to assume that panels
will conform to that and therefore parameterizing this field should
never be necessary.
Signed-off-by: Thierry Reding <treding@nvidia.com>

Instead of always enabling all four lanes, enable only the number probed
from the link.
Signed-off-by: Thierry Reding <treding@nvidia.com>

Power on only those lanes required for the specified link.
Signed-off-by: Thierry Reding <treding@nvidia.com>

Interlaced mode is currently not supported on the SOR, so don't program
any associated registers.
Signed-off-by: Thierry Reding <treding@nvidia.com>

Use the speed probed from the link at runtime rather than relying on a
hardcoded default.
Signed-off-by: Thierry Reding <treding@nvidia.com>

The number of HBLANK and VBLANK symbols can be computed at runtime so
that they can be set appropriately depending on the video mode and DP
link.

These values are used by the packet generation logic to determine how
many audio samples can be transferred during the blanking intervals.
Signed-off-by: Thierry Reding <treding@nvidia.com>

The currently hardcoded link parameters don't work on all eDP panels, so
compute the parameters at runtime depending on the mode and panel type
to allow the driver to cope with a wider variety of panels.

Note that the number of bits per pixel of the panel is still hardcoded,
but this can be addressed in a separate patch.

This is largely based on a patch by Stéphane Marchesin but the algorithm
was largely rewritten to be more readable and concise.
Signed-off-by: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Lanes are powered up in decreasing order. Power them down in increasing
order for consistency.
Signed-off-by: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>

The comment above mentions link A/B but this isn't what the code does,
so let's fix that.
Signed-off-by: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>

The code currently rounds up the clock to the next MHZ, which is
rounding up a 69.5MHz clock to 70MHz on my machine. This in turn
prevents the display from syncing. Removing this rounding fixes eDP
for me.
Signed-off-by: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>

> Bunch of stuff for 3.16 still:
> - Mipi dsi panel support for byt. Finally! From Shobhit&others. I've
>   squeezed this in since it's a regression compared to vbios and we've
>   been ridiculed about it a bit too often ...
> - connection_mutex deadlock fix in get_connector (only affects i915).
> - Core patches from Matt's primary plane from Matt Roper, I've pushed the
>   i915 stuff to 3.17.
> - vlv power well sequencing fixes from Jesse.
> - Fix for cursor size changes from Chris.
> - agpbusy fixes from Ville.
> - A few smaller things.
>

* tag 'drm-intel-fixes-2014-06-06' of git://anongit.freedesktop.org/drm-intel: (32 commits)
  drm/i915: BDW: Adding missing cursor offsets.
  drm: Fix getconnector connection_mutex locking
  drm/i915/bdw: Only use 2g GGTT for 32b platforms
  drm/i915: Nuke pipe A quirk on i830M
  drm/i915: fix display power sw state reporting
  drm/i915: Always apply cursor width changes
  drm/i915: tell the user if both KMS and UMS are disabled
  drm/plane-helper: Add drm_plane_helper_check_update() (v3)
  drm: Check CRTC compatibility in setplane
  drm/i915: use VBT to determine whether to enumerate the VGA port
  drm/i915: Don't WARN about ring idle bit on gen2
  drm/i915: Silence the WARN if the user tries to GTT mmap an incoherent object
  drm/i915: Move the C3 LP write bit setup to gen3_init_clock_gating() for KMS
  drm/i915: Enable interrupt-based AGPBUSY# enable on 85x
  drm/i915: Flip the sense of AGPBUSY_DIS bit
  drm/i915: Set AGPBUSY# bit in init_clock_gating
  drm/i915/vlv: add pll assertion when disabling DPIO common well
  drm/i915/vlv: move DPIO common reset de-assert into __vlv_set_power_well
  drm/i915/vlv: re-order power wells so DPIO common comes after TX
  drm/i915/vlv: move CRI refclk enable into __vlv_set_power_well
  ...

Other output drivers set up debugfs slightly differently. Bring the SOR
driver in line with those for consistency.
Signed-off-by: Thierry Reding <treding@nvidia.com>

Removing only the root directory will fail when there are still files in
it. Instead of manually removing all files, remove the whole directory
recursively.
Signed-off-by: Thierry Reding <treding@nvidia.com>

Doing so allows the hotplug events generated by the connector to be
properly handled by the DRM poll helpers.
Signed-off-by: Thierry Reding <treding@nvidia.com>

Calling the drm_helper_hpd_irq_event() helper can sleep, so instead of
invoking it directly from the interrupt handler, schedule a work queue
and run it from there.
Signed-off-by: Thierry Reding <treding@nvidia.com>

Enable hardware cursor support on Tegra124. Earlier generations support
the hardware cursor to some degree as well, but not in a way that can be
generically exposed.
Signed-off-by: Thierry Reding <treding@nvidia.com>

The DRM core can now cope with drivers that don't have an associated
struct drm_bus, so the host1x implementation is no longer useful.
Signed-off-by: Thierry Reding <treding@nvidia.com>

With the recent addition of the drm_set_unique() function, devices can
now be registered without requiring a drm_bus. Add a brief description
to the DRM docbook to show how that can be achieved.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Describe how devices are registered using the drm_*_init() functions.
Adding this to docbook requires a largish set of changes to the comments
in drm_{pci,usb,platform}.c since they are doxygen-style rather than
proper kernel-doc and therefore mess with the docbook generation.

While at it, mark usage of drm_put_dev() as discouraged in favour of
calling drm_dev_unregister() and drm_dev_unref() directly.
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Add a helper function that allows drivers to statically set the unique
name of the device. This will allow platform and USB drivers to get rid
of their DRM bus implementations and directly use drm_dev_alloc() and
drm_dev_register().
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

The internal host1x_{,un}register_client() functions can potentially be
confused with public the host1x_client_{,un}register() functions.

Rename them to host1x_{add,del}_client() to remove some of the possible
confusion.
Signed-off-by: Thierry Reding <treding@nvidia.com>

The function is never used outside of the source file and therefore can
be locally scoped.
Signed-off-by: Thierry Reding <treding@nvidia.com>

Tegra124 is mostly backwards-compatible with Tegra114. However, Tegra124
supports a few more features (e.g. interlacing, ...). Introduce a new
compatible string and TMDS tables to cope with these differences.
Signed-off-by: Thierry Reding <treding@nvidia.com>