Since commit bb276262 ("mtd: spi-nor: only apply reset hacks to
broken hardware"), we need to mark the spi-nor as "broken" for reboot
to work.
Note that nothing is actually broken here.  The hardware-watchdog in
the SoC isn't wired in a way that works, but then the board doesn't
claim to support a hardware watchdog - and the SPI certain isn't
"broken".

This causes an annoying warning on every boot, but that is better than
failing on ever reboot.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Since commit f8c55dc6 ("MIPS: use generic dma noncoherent ops for
simple noncoherent platforms") changed MIPS dma handling, the mmc
driver fails because it doesn't have a dma mask is set.

So set the correct dma mask.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Since commit f8c55dc6 ("MIPS: use generic dma noncoherent ops for
simple noncoherent platforms") changed MIPS dma handling, the eth
driver fails because the dma mask is set on the wrong 'struct device'.

Move the setting to the correct struct device.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

I had started the removal of semaphores in this driver without knowing
that Nicolas Saenz Julienne also worked on this. In case of the "remote
event" infrastructure, my solution seemed significantly better, so I'm
proposing this as a change on top.

The problem with using either semaphores or completions here is that
it's an overly complex way of waking up a thread, and it looks like the
'count' of the semaphore can easily get out of sync, even though I found
it hard to come up with a specific example.

Changing it to a 'wait_queue_head_t' instead of a completion simplifies
this by letting us wait directly on the 'event->fired' variable that is
set by the videocore.

Another simplification is passing the wait queue directly into the helper
functions instead of going through the fragile logic of recording the
offset inside of a structure as part of a shared memory variable. This
also avoids one uncached memory read and should be faster.

Note that I'm changing it back to 'killable' after the previous patch
changed 'killable' to 'interruptible', apparently based on a misunderstanding
of the subtle down_interruptible() macro override in vchiq_killable.h.

Fixes: f27e47bc ("staging: vchiq: use completions instead of semaphores")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Nothing uses the semaphores any more in this driver, so remove
all references to that type.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This semaphore is used like a mutex, so it should use the regular
mutex API, as we do in the other copies of this driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This driver uses many semaphores, most of them are equivalent to
completions. The other copies of this driver got moved over to
completions a while ago, so do the same here.

In this usage scenario, the two are equivalent, so the behavior
should not change.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

HGz -> GHz
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The function rtw_port_switch_chk() returns always false.
Remove the function and related dead code.
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use Hal_GetChnlGroup88E() instead of duplicating it's code
in get_rx_power_val_by_reg().
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Zeroing the array result[m][n] and setting only the values at
even 'n's simplifies the code and slightly reduces object file
size.
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Changes do_insn*_ioctl functions to allow for data lengths for each
comedi_insn of up to 2^16.  This patch also changes these functions to only
allocate as much memory as is necessary for each comedi_insn, rather than
allocating a fixed-sized scratch space.

In testing some user-space code for the new INSN_DEVICE_CONFIG_GET_ROUTES
facility with some newer hardware, I discovered that do_insn_ioctl and
do_insnlist_ioctl limited the amount of data that can be passed into the
kernel for insn's to a length of 256.  For some newer hardware, the number
of routes can be greater than 1000.  Working around the old limits (256)
would complicate the user-space/kernel interaction.

The new upper limit is reasonable with current memory available and does
not otherwise impact the memory footprint for any current or otherwise
typical configuration.
Signed-off-by: Spencer E. Olson <olsonse@umich.edu>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

As explained in previous patch, this SPI controller seems to be
tested on SPI flash only before mass production and some bits are
swizzled under other SPI modes probably due to incorrect wiring
inside the silicon. Drop implementation of SPI mode 1/2/3 since
they are broken.

Also drop RT2880_SPI_MODE_BITS macro because we now have only
SPI_LSB_FIRST implemented and the mode_bits is so short that we
don't need a macro there.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Reviewed-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

According to John Crispin (aka blogic) on IRC on Nov 26 2018:
  so basically i made cs1 work for MTK/labs when i built
  the linkit smart for them. the req-sheet said that cs1 should be proper
  duplex spi. however ....
   1) the core will always send 1 byte before any transfer, this is the
      m25p80 command.
   2) mode 3 is broken and bit reversed (?)
   3) some bit are incorrectly wired in hw for mode2/3
  we wrote a test script and test for [0-0xffff] on all modes and certain
  bits are swizzled under certain conditions and it was not possible to
  fix this even using a hack.
  we then decided to use spi-gpio and i never removed the errornous code
  basically the spi is fecked for anything but half duplex spi mode0
  running a sflash on it

The controller will always send some data from OPCODE register under half
duplex mode before starting a full-duplex transfer, so the full-duplex
mode is broken.
This piece of code also make CS1 unavailable since it forces the
broken full-duplex mode to be used on CS1.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Reviewed-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In this driver, both function the same way, but we want to eventually
kill off semaphores, so a completion is the better choice here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Changed "stoped" to "stopped".
Signed-off-by: Aaron Strahlberger <aaron.strahlberger@posteo.de>
Signed-off-by: Julius Wiedmann <julius.wiedmann@fau.de>
Signed-off-by: Dominik Huber <domi250@gmx.de>
Reviewed-by: Gao Xiang <gaoxiang25@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

It's better to use pre-calculated values to make
on-disk definition more straight-forward and human-readable.

Since there is the only one user, let's remove
__EROFS_BIT entirely.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Gao Xiang <hsiangkao@aol.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

remove all redundant BUG_ONs, and turn the rest
useful usages to DBG_BUGONs.
Signed-off-by: Gao Xiang <gaoxiang25@huawei.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

remove all redundant BUG_ONs, and turn the rest
useful usages to DBG_BUGONs.
Signed-off-by: Gao Xiang <gaoxiang25@huawei.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We want the staging fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull networking fixes from David Miller:
 "A decent batch of fixes here. I'd say about half are for problems that
  have existed for a while, and half are for new regressions added in
  the 4.20 merge window.

   1) Fix 10G SFP phy module detection in mvpp2, from Baruch Siach.

   2) Revert bogus emac driver change, from Benjamin Herrenschmidt.

   3) Handle BPF exported data structure with pointers when building
      32-bit userland, from Daniel Borkmann.

   4) Memory leak fix in act_police, from Davide Caratti.

   5) Check RX checksum offload in RX descriptors properly in aquantia
      driver, from Dmitry Bogdanov.

   6) SKB unlink fix in various spots, from Edward Cree.

   7) ndo_dflt_fdb_dump() only works with ethernet, enforce this, from
      Eric Dumazet.

   8) Fix FID leak in mlxsw driver, from Ido Schimmel.

   9) IOTLB locking fix in vhost, from Jean-Philippe Brucker.

  10) Fix SKB truesize accounting in ipv4/ipv6/netfilter frag memory
      limits otherwise namespace exit can hang. From Jiri Wiesner.

  11) Address block parsing length fixes in x25 from Martin Schiller.

  12) IRQ and ring accounting fixes in bnxt_en, from Michael Chan.

  13) For tun interfaces, only iface delete works with rtnl ops, enforce
      this by disallowing add. From Nicolas Dichtel.

  14) Use after free in liquidio, from Pan Bian.

  15) Fix SKB use after passing to netif_receive_skb(), from Prashant
      Bhole.

  16) Static key accounting and other fixes in XPS from Sabrina Dubroca.

  17) Partially initialized flow key passed to ip6_route_output(), from
      Shmulik Ladkani.

  18) Fix RTNL deadlock during reset in ibmvnic driver, from Thomas
      Falcon.

  19) Several small TCP fixes (off-by-one on window probe abort, NULL
      deref in tail loss probe, SNMP mis-estimations) from Yuchung
      Cheng"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (93 commits)
  net/sched: cls_flower: Reject duplicated rules also under skip_sw
  bnxt_en: Fix _bnxt_get_max_rings() for 57500 chips.
  bnxt_en: Fix NQ/CP rings accounting on the new 57500 chips.
  bnxt_en: Keep track of reserved IRQs.
  bnxt_en: Fix CNP CoS queue regression.
  net/mlx4_core: Correctly set PFC param if global pause is turned off.
  Revert "net/ibm/emac: wrong bit is used for STA control"
  neighbour: Avoid writing before skb->head in neigh_hh_output()
  ipv6: Check available headroom in ip6_xmit() even without options
  tcp: lack of available data can also cause TSO defer
  ipv6: sr: properly initialize flowi6 prior passing to ip6_route_output
  mlxsw: spectrum_switchdev: Fix VLAN device deletion via ioctl
  mlxsw: spectrum_router: Relax GRE decap matching check
  mlxsw: spectrum_switchdev: Avoid leaking FID's reference count
  mlxsw: spectrum_nve: Remove easily triggerable warnings
  ipv4: ipv6: netfilter: Adjust the frag mem limit when truesize changes
  sctp: frag_point sanity check
  tcp: fix NULL ref in tail loss probe
  tcp: Do not underestimate rwnd_limited
  net: use skb_list_del_init() to remove from RX sublists
  ...

Pull x86 fixes from Ingo Molnar:
 "Three fixes: a boot parameter re-(re-)fix, a retpoline build artifact
  fix and an LLVM workaround"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/vdso: Drop implicit common-page-size linker flag
  x86/build: Fix compiler support check for CONFIG_RETPOLINE
  x86/boot: Clear RSDP address in boot_params for broken loaders

Pull kprobes fixes from Ingo Molnar:
 "Two kprobes fixes: a blacklist fix and an instruction patching related
  corruption fix"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  kprobes/x86: Blacklist non-attachable interrupt functions
  kprobes/x86: Fix instruction patching corruption when copying more than one RIP-relative instruction

Pull EFI fixes from Ingo Molnar:
 "Two fixes: a large-system fix and an earlyprintk fix with certain
  resolutions"

* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/earlyprintk/efi: Fix infinite loop on some screen widths
  x86/efi: Allocate e820 buffer before calling efi_exit_boot_service

Currently, duplicated rules are rejected only for skip_hw or "none",
hence allowing users to push duplicates into HW for no reason.

Use the flower tables to protect for that.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reported-by: Chris Mi <chrism@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Michael Chan says:

====================
bnxt_en: Bug fixes.

The first patch fixes a regression on CoS queue setup, introduced
recently by the 57500 new chip support patches.  The rest are
fixes related to ring and resource accounting on the new 57500 chips.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The CP rings are accounted differently on the new 57500 chips.  There
must be enough CP rings for the sum of RX and TX rings on the new
chips.  The current logic may be over-estimating the RX and TX rings.

The output parameter max_cp should be the maximum NQs capped by
MSIX vectors available for networking in the context of 57500 chips.
The existing code which uses CMPL rings capped by the MSIX vectors
works most of the time but is not always correct.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The new 57500 chips have introduced the NQ structure in addition to
the existing CP rings in all chips.  We need to introduce a new
bnxt_nq_rings_in_use().  On legacy chips, the 2 functions are the
same and one will just call the other.  On the new chips, they
refer to the 2 separate ring structures.  The new function is now
called to determine the resource (NQ or CP rings) associated with
MSIX that are in use.

On 57500 chips, the RDMA driver does not use the CP rings so
we don't need to do the subtraction adjustment.

Fixes: 41e8d798 ("bnxt_en: Modify the ring reservation functions for 57500 series chips.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The new 57500 chips use 1 NQ per MSIX vector, whereas legacy chips use
1 CP ring per MSIX vector.  To better unify this, add a resv_irqs
field to struct bnxt_hw_resc.  On legacy chips, we initialize resv_irqs
with resv_cp_rings.  On new chips, we initialize it with the allocated
MSIX resources.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Recent changes to support the 57500 devices have created this
regression.  The bnxt_hwrm_queue_qportcfg() call was moved to be
called earlier before the RDMA support was determined, causing
the CoS queues configuration to be set before knowing whether RDMA
was supported or not.  Fix it by moving it to the right place right
after RDMA support is determined.

Fixes: 98f04cf0 ("bnxt_en: Check context memory requirements from firmware.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull char/misc driver fixes from Greg KH:
 "Here are some small driver fixes for 4.20-rc6.

  There is a hyperv fix that for some reaon took forever to get into a
  shape that could be applied to the tree properly, but resolves a much
  reported issue. The others are some gnss patches, one a bugfix and the
  two others updates to the MAINTAINERS file to properly match the gnss
  files in the tree.

  All have been in linux-next for a while with no reported issues"

* tag 'char-misc-4.20-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  MAINTAINERS: exclude gnss from SIRFPRIMA2 regex matching
  MAINTAINERS: add gnss scm tree
  gnss: sirf: fix activation retry handling
  Drivers: hv: vmbus: Offload the handling of channels to two workqueues

Pull staging fixes from Greg KH:
 "Here are two staging driver bugfixes for 4.20-rc6.

  One is a revert of a previously incorrect patch that was merged a
  while ago, and the other resolves a possible buffer overrun that was
  found by code inspection.

  Both of these have been in the linux-next tree with no reported
  issues"

* tag 'staging-4.20-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  Revert commit ef9209b6 "staging: rtl8723bs: Fix indenting errors and an off-by-one mistake in core/rtw_mlme_ext.c"
  staging: rtl8712: Fix possible buffer overrun

Pull tty driver fixes from Greg KH:
 "Here are three small tty driver fixes for 4.20-rc6

  Nothing major, just some bug fixes for reported issues. Full details
  are in the shortlog.

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'tty-4.20-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  kgdboc: fix KASAN global-out-of-bounds bug in param_set_kgdboc_var()
  tty: serial: 8250_mtk: always resume the device in probe.
  tty: do not set TTY_IO_ERROR flag if console port

Pull USB fixes from Greg KH:
 "Here are some small USB fixes for 4.20-rc6

  The "largest" here are some xhci fixes for reported issues. Also here
  is a USB core fix, some quirk additions, and a usb-serial fix which
  required the export of one of the tty layer's functions to prevent
  code duplication. The tty maintainer agreed with this change.

  All of these have been in linux-next with no reported issues"

* tag 'usb-4.20-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  xhci: Prevent U1/U2 link pm states if exit latency is too long
  xhci: workaround CSS timeout on AMD SNPS 3.0 xHC
  USB: check usb_get_extra_descriptor for proper size
  USB: serial: console: fix reported terminal settings
  usb: quirk: add no-LPM quirk on SanDisk Ultra Flair device
  USB: Fix invalid-free bug in port_over_current_notify()
  usb: appledisplay: Add 27" Apple Cinema Display

Pull cifs fixes from Steve French:
 "Three small fixes: a fix for smb3 direct i/o, a fix for CIFS DFS for
  stable and a minor cifs Kconfig fix"

* tag '4.20-rc5-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
  CIFS: Avoid returning EBUSY to upper layer VFS
  cifs: Fix separator when building path from dentry
  cifs: In Kconfig CONFIG_CIFS_POSIX needs depends on legacy (insecure cifs)

Pull dax fixes from Dan Williams:
 "The last of the known regression fixes and fallout from the Xarray
  conversion of the filesystem-dax implementation.

  On the path to debugging why the dax memory-failure injection test
  started failing after the Xarray conversion a couple more fixes for
  the dax_lock_mapping_entry(), now called dax_lock_page(), surfaced.
  Those plus the bug that started the hunt are now addressed. These
  patches have appeared in a -next release with no issues reported.

  Note the touches to mm/memory-failure.c are just the conversion to the
  new function signature for dax_lock_page().

  Summary:

   - Fix the Xarray conversion of fsdax to properly handle
     dax_lock_mapping_entry() in the presense of pmd entries

   - Fix inode destruction racing a new lock request"

* tag 'dax-fixes-4.20-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  dax: Fix unlock mismatch with updated API
  dax: Don't access a freed inode
  dax: Check page->mapping isn't NULL

Pull libnvdimm fixes from Dan Williams:
 "A regression fix for the Address Range Scrub implementation, yes
  another one, and support for platforms that misalign persistent memory
  relative to the Linux memory hotplug section constraint. Longer term,
  support for sub-section memory hotplug would alleviate alignment
  waste, but until then this hack allows a 'struct page' memmap to be
  established for these misaligned memory regions.

  These have all appeared in a -next release, and thanks to Patrick for
  reporting and testing the alignment padding fix.

  Summary:

   - Unless and until the core mm handles memory hotplug units smaller
     than a section (128M), persistent memory namespaces must be padded
     to section alignment.

     The libnvdimm core already handled section collision with "System
     RAM", but some configurations overlap independent "Persistent
     Memory" ranges within a section, so additional padding injection is
     added for that case.

   - The recent reworks of the ARS (address range scrub) state machine
     to reduce the number of state flags inadvertantly missed a
     conversion of acpi_nfit_ars_rescan() call sites. Fix the regression
     whereby user-requested ARS results in a "short" scrub rather than a
     "long" scrub.

   - Fixup the unit tests to handle / test the 128M section alignment of
     mocked test resources.

* tag 'libnvdimm-fixes-4.20-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  acpi/nfit: Fix user-initiated ARS to be "ARS-long" rather than "ARS-short"
  libnvdimm, pfn: Pad pfn namespaces relative to other regions
  tools/testing/nvdimm: Align test resources to 128M

rx_ppp and tx_ppp can be set between 0 and 255, so don't clamp to 1.

Fixes: 6e8814ce ("net/mlx4_en: Fix mixed PFC and Global pause user control requests")
Signed-off-by: Tarick Bedeir <tarick@google.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull thermal SoC fixes from Eduardo Valentin:
 "Fixes for armada and broadcom thermal drivers"

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
  thermal: broadcom: constify thermal_zone_of_device_ops structure
  thermal: armada: constify thermal_zone_of_device_ops structure
  thermal: bcm2835: Switch to SPDX identifier
  thermal: armada: fix legacy resource fixup
  thermal: armada: fix legacy validity test sense