The gpmi's IP for imx6sx is nearly the same as the gpmi's IP for imx6q,
except the following two new features:

     (1) the new BCH contoller has 62-BIT correcting ECC strength
            (The BCH for imx6q only has 40-BIT ECC strength).

     (2) add the hardware Randomizer support.

This patch does the follow changes:

     (1) add a new macro GPMI_IS_MX6SX to represent the imx6sx's gpmi.

     (2) add a new macro GPMI_IS_MX6.
           We use this macro to initialize the same registers for both
         imx6sx and imx6q, and so on.

     (3) add a new gpmi_devdata instance, the gpmi_devdata_imx6sx, for
         imx6sx.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Since (a few releases before) v2.6.0 there have been checks for
CONFIG_MTD_SUPERH_RESERVE. One check is still present. But a Kconfig
symbol MTD_SUPERH_RESERVE has never been added. So a few lines of dead
code can be removed.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

This patch moves data allocated using kzalloc to managed data allocated
using devm_kzalloc and cleans now unnecessary kfrees in probe and remove
functions. Also, the now unnecessary label out_err_hw_init is done away
with and the label out_err_kzalloc is renamed to out_err.

The following Coccinelle semantic patch was used for making the change:

@platform@
identifier p, probefn, removefn;
@@
struct platform_driver p = {
  .probe = probefn,
  .remove = removefn,
};

@prb@
identifier platform.probefn, pdev;
expression e, e1, e2;
@@
probefn(struct platform_device *pdev, ...) {
  <+...
- e = kzalloc(e1, e2)
+ e = devm_kzalloc(&pdev->dev, e1, e2)
  ...
?-kfree(e);
  ...+>
}

@rem depends on prb@
identifier platform.removefn;
expression e;
@@
removefn(...) {
  <...
- kfree(e);
  ...>
}
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

The pxa3xx_nand driver currently uses __raw_writel() and __raw_readl()
to access I/O registers. However, those functions do not do any
endianness swapping, which means that they won't work when the CPU
runs in big-endian but the I/O registers are little endian, which is
the common situation for ARM systems running big endian.

Since __raw_writel() and __raw_readl() do not include any memory
barriers and the pxa3xx_nand driver can only be compiled for ARM
platforms, the closest I/o accessors functions that do endianess
swapping are writel_relaxed() and readl_relaxed().

This patch has been verified to work on Armada XP GP: without the
patch, the NAND is not detected when the kernel runs big endian while
it is properly detected when the kernel runs little endian. With the
patch applied, the NAND is properly detected in both situations
(little and big endian).
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: <stable@vger.kernel.org> # v3.13+
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

 Fixes:  2c9f2365
 mtd: nand: omap: ecc.calculate: merge omap3_calculate_ecc_bch4 in omap_calculate_ecc_bch

 Fixes: 7bcd1dca
 mtd: nand: omap: ecc.calculate: merge omap3_calculate_ecc_bch8 in omap_calculate_ecc_bch

Cc: <stable@vger.kernel.org> # 3.13.x+
Signed-off-by: Ted Juan <ted.juan@gmail.com>
Acked-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

The two loops in r852_write_buf() are designed to handle 4-byte-aligned
and then 1-byte-aligned portions, respectively. However, there are two
issues:

(1) The first loop will only terminate if 'len' is a multiple of 4
(2) The second loop will never terminate if it runs at least once

Rewrite these loops as they were probably intended. Compile tested only.

Issues pointed out by Coverity Scan.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Maxim Levitsky <maximlevitsky@gmail.com>

Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Set, but unused, variable.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

On m86k, and maybe a few other architectures, we get this kind of
warning, due to misuse of volatile:

   drivers/mtd/maps/sc520cdp.c: In function 'sc520cdp_setup_par':
>> drivers/mtd/maps/sc520cdp.c:223:2: warning: passing argument 1 of 'iounmap' discards 'volatile' qualifier from pointer target type [enabled by default]
   arch/m68k/include/asm/raw_io.h:22:13: note: expected 'void *' but argument is of type 'volatile long unsigned int *'

Rather than annotating the variable declaration, let's just use the
proper accessors, which add the 'volatile' qualifier to the operation.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

  drivers/mtd/devices/slram.c: In function 'init_slram':
  drivers/mtd/devices/slram.c:283:6: warning: variable 'i' set but not used [-Wunused-but-set-variable]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Fixes warning:

In file included from drivers/mtd/lpddr/qinfo_probe.c:31:0:
include/linux/mtd/pfow.h: In function ‘send_pfow_command’:
include/linux/mtd/pfow.h:104:6: warning: variable ‘chipnum’ set but not used [-Wunused-but-set-variable]
  int chipnum;
      ^
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Not all architectures implement a writel_relaxed() accessor. Hopefully
this will change eventually, but for now, this means lpddr2_nvm.c can't
compile on some architectures.

Let's add an ARM dependency for now, and leave a comment so maybe we can
change this in the future.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Vincenzo Aliberti <vincenzo.aliberti@gmail.com>

This commit updates the devicetree binding documentation for this driver
with the supported ECC strength and step size combinations.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

This commit adds support for the user to specify the ECC strength
and step size through the devicetree. We keep the previous behavior,
when there is no DT parameter provided.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Let's make pxa_ecc_init() return a negative errno on error or zero
if succesful, which is standard kernel practice. Also, report the
selected ECC strength and step size, which is important information.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

This commit makes use of the chip->ecc_strength_ds and chip->ecc_step_ds which
contain the datasheet minimum requested ECC strength to produce a noisy warning
if the configured ECC strength is weaker.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

- Adds DT binding property for BCH16 ECC scheme
 - Adds describes on factors which determine choice of ECC scheme for particular device

CC: devicetree@vger.kernel.org
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

This patch add support for BCH16 ecc-scheme in OMAP NAND driver, by extending
following functions:
 - omap_enable_hwecc (nand_chip->ecc.hwctl): configure GPMC controller
 - omap_calculate_ecc_bch (nand_chip->ecc.calculate): fetch ECC signature from GPMC controller
 - omap_elm_correct_data (nand_chip->ecc.correct): detect and correct ECC errors using ELM

(a) BCH16 ecc-scheme can detect and correct 16 bit-flips per 512Bytes of data.
(b) BCH16 ecc-scheme generates 26-bytes of ECC syndrome / 512B.
Due to (b) this scheme can only be used with NAND devices which have enough
OOB to satisfy the relation: "OOBsize per page >= 26 * (page-size / 512)"
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

ELM hardware engine is used to detect ECC errors for BCHx ecc-schemes
(like BCH4/BCH8/BCH16). This patch extends configuration of ELM registers
for adding support of BCH16_HW ecc-scheme.
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

This patch add support for BCH16_ECC in GPMC (controller) driver:
- extends configuration space to include BCH16 registers
- extends parsing of DT binding for selecting BCH16 ecc-scheme
Signed-off-by: Pekon Gupta <pekon@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Signed-off-by: Ron Lee <ron@debian.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Signed-off-by: Vincenzo Aliberti <vincenzo.aliberti@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Enhances the help for the CFI command set choices.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

A workaround was already in place that set the WP bit in the
IFC_CSPR0 register after a STATUS command, however it used an 8-bit
write method. As a result, the WP bit was never set on 16-bit devices,
and these devices would eventually be incorrectly marked as
write-protected.

This patch checks the chip options for a 16-bit device and uses the
appropriate write method to set the WP bit after a STATUS command.
Signed-off-by: Joe Schultz <jschultz@xes-inc.com>
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

The IFC buffer is accessed via 8-bit and 16-bit accessors. Changing
the 'addr' member of 'struct fsl_ifc_nand_ctrl' from 'u8 __iomem *' to
'void __iomem *' eliminates the need for explicit casts when the
16-bit accessors are used.
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

The break statements should be indented another tab.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

nand_base can be passed a kmap()'d buffers from highmem by
filesystems like jffs2. This results in failure to map the
physical address of the DMA buffer on various contoller
driver on different platforms. This change adds a chip option
to use preallocated databuf as bounce buffers used in
nand_do_read_ops() and nand_do_write_ops().
This allows for specific nand controller driver to set this
option as needed.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

The m25p80.c has used the SPI NOR framework now, and the m25p_ids has
been moved to spi-nor.c and renamed to spi_nor_ids.

This patch updates the document for m25p80.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

As subpage write is enabled by default for all drivers, nand_write_subpage_hwecc
causes a crash if the driver did not register ecc->hwctl or ecc->calculate.
This behavior was introduced in
   commit 837a6ba4
   "mtd: nand: subpage write support for hardware based ECC schemes".

This fixes a crash by emulating subpage write support by padding sub-page data
with 0xff on either sides to make it full page compatible.
Reported-by: Helmut Schaa <helmut.schaa@googlemail.com>
Tested-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Pekon Gupta <pekon@ti.com>
Reviewed-by: Scott Wood <scottwood@freescale.com>
Cc: <stable@vger.kernel.org> # 3.10.x+
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

The samsung onenand driver passes around a dma address token
through a void pointer, which is incorrect and leads to
warnings like this one:

onenand/samsung.c:548:2: warning: passing argument 1 of '__fswab32' makes integer from pointer without a cast [enabled by default]
  writel(src, base + S5PC110_DMA_SRC_ADDR);
  ^

This patch makes it use dma_addr_t here, which is more appropriate.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Make of_device_id array const, because all OF functions
handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Make of_device_id array const, because all OF functions
handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Make of_device_id array const, because all OF functions
handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

On m68k, where access_ok() doesn't cast the address parameter:

drivers/mtd/mtdchar.c: In function 'mtdchar_write_ioctl':
drivers/mtd/mtdchar.c:575:4: warning: passing argument 2 of 'access_ok' makes pointer from integer without a cast [enabled by default]
arch/m68k/include/asm/uaccess_mm.h:17:90: note: expected 'const void *' but argument is of type '__u64'
drivers/mtd/mtdchar.c:576:4: warning: passing argument 2 of 'access_ok' makes pointer from integer without a cast [enabled by default]
arch/m68k/include/asm/uaccess_mm.h:17:90: note: expected 'const void *' but argument is of type '__u64'

The address parameter of access_ok() is really a userspace pointer.
On most architectures, access_ok() is a macro that casts the address
parameter, hiding issues in its users.

Move around and use the existing usr_data and usr_oob temporary variables
to kill the warnings. Add a few "consts", and make more use of the
temporaries while we're at it.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

fixes: commit 62116e51
       mtd: nand: omap2: Support for hardware BCH error correction.

In omap_elm_correct_data(), if bitflip_count in an erased-page is within the
correctable limit (< ecc.strength), then it is not indicated back to the caller
ecc->read_page().

This mis-guides upper layers like MTD and UBIFS layer to assume erased-page as
perfectly clean and use it for writing even if actual bitflip_count was
dangerously high (bitflip_count > mtd->bitflip_threshold).

This patch fixes this above issue, by returning 'stats' to caller
ecc->read_page() under all scenarios.
Reported-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Pekon Gupta <pekon@ti.com>
Cc: <stable@vger.kernel.org> # 3.9.x+
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Spansion s25sl032p supports Dual and Quad SPI transfers, hence set the
SPI_NOR_DUAL_READ and SPI_NOR_QUAD_READ flags.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Commit 03e296f6 ("mtd: m25p80: use the SPI
nor framework") accidentally removed support for Dual SPI read transfers.
Add it back.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Fixes:
drivers/mtd/devices/elm.c:480:12: warning: 'elm_suspend' defined but not used [-Wunused-function]
drivers/mtd/devices/elm.c:488:12: warning: 'elm_resume' defined but not used [-Wunused-function]
Signed-off-by: Wolfram Sang <wsa@sang-engineering.com>
Acked-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Anyone working with an AMD Elan SC520 development or evaluation board
would be building a dedicated kernel for it, so we can make the
sc520cdp and netsc520 maps depend on MELAN. SC520_CPUFREQ already
depends on MELAN so it makes things more consistent. It also makes
kernel configuration for every other x86 user easier.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

The nand_chip::erase_cmd callback previously served a dual purpose; for
one, it allowed a per-flash-chip override, so that AG-AND devices could
use a different erase command than other NAND. These AND devices were
dropped in commit 14c65786 (mtd: nand:
remove AG-AND support). On the other hand, some drivers (denali and
doc-g4) need to use this sort of callback to implement
controller-specific erase operations.

To make the latter operation easier for some drivers (e.g., ST's new BCH
NAND driver), it helps if the command dispatch and wait functions can be
lumped together, rather than called separately.

This patch does two things:
 1. Pull the call to chip->waitfunc() into chip->erase_cmd(), and return
    the status from this callback
 2. Rename erase_cmd() to just erase(), since this callback does a
    little more than just send a command
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by: Lee Jones <lee.jones@linaro.org>