- 23 Jun, 2016 3 commits
-
-
Ramesh Shanmugasundaram authored
As per Wolfgang G, all new drivers should support decreasing state transition(back-to-error-active). This patch adds this support. This driver configures the controller to halt on bus-off entry. Hence, when in error states less than bus off state, the TEC/REC counters are checked for lower state transition eligibility and action. Signed-off-by:
Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de>
-
Ramesh Shanmugasundaram authored
The controller can operate in one of the two global modes - CAN FD only mode (default) - Classical CAN (CAN2.0) only mode This patch adds support for Classical CAN only mode. It can be enabled by defining the optional device tree property "renesas,no-can-fd" of this node. Note: R-Car Gen3 h/w manual v0.51E shows bit6 of RSCFDnCFDGCFG as reserved, which is incorrect. This bit is same as RSCFDnGCFG. Signed-off-by:
-
Arnd Bergmann authored
The change to leave out procfs support in CAN when CONFIG_PROC_FS is not set was incomplete and leads to a build error: net/built-in.o: In function `can_init': :(.init.text+0x9858): undefined reference to `can_stat_update' ERROR: "can_stat_update" [net/can/can.ko] undefined! This tries a better approach, encapsulating all of the calls within IS_ENABLED(), so we also leave out the timer function from the object file. Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Fixes: a20fadf8 ("can: build proc support only if CONFIG_PROC_FS is activated") Signed-off-by:
-
- 22 Jun, 2016 7 commits
-
-
William Tu authored
The commit f2a4d086 ("openvswitch: Add packet truncation support.") introduces packet truncation before sending to userspace upcall receiver. This patch passes up the skb->len before truncation so that the upcall receiver knows the original packet size. Potentially this will be used by sFlow, where OVS translates sFlow config header=N to a sample action, truncating packet to N byte in kernel datapath. Thus, only N bytes instead of full-packet size is copied from kernel to userspace, saving the kernel-to-userspace bandwidth. Signed-off-by:
William Tu <u9012063@gmail.com> Cc: Pravin Shelar <pshelar@nicira.com> Acked-by:
Pravin B Shelar <pshelar@ovn.org> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Philippe Reynes authored
There are two generics functions phy_ethtool_{get|set}_link_ksettings, so we can use them instead of defining the same code in the driver. Signed-off-by:Philippe Reynes <tremyfr@gmail.com> Signed-off-by:
-
Philippe Reynes authored
The private structure contain a pointer to phydev, but the structure net_device already contain such pointer. So we can remove the pointer phydev in the private structure, and update the driver to use the one contained in struct net_device. Signed-off-by:
-
Philippe Reynes authored
There are two generics functions phy_ethtool_{get|set}_link_ksettings, so we can use them instead of defining the same code in the driver. Signed-off-by: -
Philippe Reynes authored
The private structure contain a pointer to phydev, but the structure net_device already contain such pointer. So we can remove the pointer phydev in the private structure, and update the driver to use the one contained in struct net_device. Signed-off-by:
-
Philippe Reynes authored
There are two generics functions phy_ethtool_{get|set}_link_ksettings, so we can use them instead of defining the same code in the driver. Signed-off-by: -
Philippe Reynes authored
The private structure contain a pointer to phydev, but the structure net_device already contain such pointer. So we can remove the pointer phydev in the private structure, and update the driver to use the one contained in struct net_device. Signed-off-by:
-
- 21 Jun, 2016 30 commits
-
-
David S. Miller authored
Jiri Pirko says: ==================== mlxsw: Preparation for IPv4 router Ido says: This series prepares the driver for IPv4 router support. The router follow-up patches are available at: https://github.com/jpirko/linux_mlxsw/tree/net-next_queue Patches 1-9 simplify the netdevice notification block and also add several checks during PRECHANGEUPPER events against topologies that aren't supported by the device. This will ensure L3 interfaces are only configured on top of valid netdevs. Patches 10-13 contain trivial changes required for the introduction of a generic FID struct - currently only used for vFIDs - in patch 14. Making the FID struct generic will allow us to easily associate the underlying FIDs with their L3-counterparts - Router interfaces (RIFs): FID Type | Used by | RIF Type -------------------------------------------------------- FID | The VLAN-aware bridge | VLAN vFID | VLAN-unaware bridges | FID rFID | non-bridged netdevs (follow-up) | Sub-port Obligatory ASCII art to visualize the above: A.B.C.D + | FID RIF + br0 E.F.G.H + + | | VLAN RIF +---------+---------+ + | | br1.W | vFID | + | | | vPort +-+-+ +-+-+ + swXpY.Z | | | | br1 +-+-+ +-+-+ + | | FID=W | | | +------------+------------+ | | | | +---+---+ +---+-+-+ +---+---+ | | | | | | | | | | | | | | | | | | +-------+ +-------+ +-------+ swXpY Patches 15-16 further generalize the struct by exploiting the fact that the FID is a shared resource among ports. Each FID type is assigned a 'leave' function that is invoked based on CHANGEUPPER events and takes care of the necessary clean-up. Patches 17-22 build upon the previous patches and use the FID struct for the VLAN-aware bridge and take care of cleaning up FID resources in the 'leave' functions. For now, these are only FDB records, but later on we'll have to remove the RIFs associated with these FIDs, which will in turn take care of routes and neighbours clean-up. The last patch adds debug prints that proved very useful during the development of this series. Tested with the existing L2 recipes: https://github.com/jpirko/lnst/tree/master/recipes/switchdev ==================== Signed-off-by:
-
Ido Schimmel authored
For debug purposes, it's useful to know the order in which the driver responds to changes in the topology of its upper devices. Add debug prints to signal these events. Signed-off-by:
Ido Schimmel <idosch@mellanox.com> Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
-
Ido Schimmel authored
There are situations in which a vPort is destroyed while still holding references to device's resources such as FIDs and FDB records. This can happen, for example, when a VLAN device is deleted while still being bridged. Instead of trying to make sure vPort destruction is invoked when it no longer uses device's resources, just free them upon destruction. This simplifies the code, as we no longer need to take different situations into account when events are received - cleanup is taken care of in one place. Signed-off-by:
-
Ido Schimmel authored
FDB entries are learned using {Port / LAG ID, FID} and therefore should be flushed whenever a port (vPort) leaves its FID (vFID). However, when the bridge port is a LAG device (or a VLAN device on top), then FDB flushing is conditional. Ports removed from such LAG configurations must not trigger flushing, as other ports might still be members in the LAG and therefore the bridge port is still active. The decision whether to flush or not was previously computed in the netdevice notification block, but in order to flush the entries when a port leaves its FID this decision should be computed there. Strip the notification block from this logic and instead move it to one FDB flushing function that is invoked from both the FID / vFID leave functions. When port isn't member in LAG, FDB flushing should always occur. Otherwise, it should occur only when the last port (vPort) member in the LAG leaves the FID (vFID). This will allow us - in the next patch - to simplify the cleanup code paths that are hit whenever the topology above the port netdevs changes. Signed-off-by: -
Ido Schimmel authored
Not all vPorts will have FIDs assigned to them, so make sure functions first test for FID presence. Signed-off-by:
-
Ido Schimmel authored
As previously explained, not all vPorts will be assigned FIDs, so instead of returning the FID index of a vPort, return a pointer to its FID struct. This will allow us to know whether it's legal to access the vPort's FID parameters such as index and device. Signed-off-by:
-
Ido Schimmel authored
When L3 interfaces will be introduced a vPort won't necessarily have a FID assigned to it. This can happen if it's not member in a bridge (in which case it's assigned a vFID) or doesn't have an IP address (in which case it's assigned an rFID). Therefore, instead check the VID parameter to test whether a port is a vPort or not. Signed-off-by:
-
Ido Schimmel authored
In a very similar way to the vFIDs, make the first 4K FIDs - used in the VLAN-aware bridge - use the new FID struct. Upon first use of the FID by any of the ports do the following: 1) Create the FID 2) Setup a matching flooding entry 3) Create a mapping for the FID Unlike vFIDs, upon creation of a FID we always create a global VID-to-FID mapping, so that ports without upper vPorts can use it instead of creating an explicit {Port, VID} to FID mapping. When a port leaves a FID the reverse is performed. Whenever the FID's reference count reaches zero the FID is deleted along with the global mapping. The per-FID struct will later allow us to configure L3 interfaces on top of the VLAN-aware bridge. Signed-off-by: -
Ido Schimmel authored
Signed-off-by:
-
Ido Schimmel authored
When a vPort is created or when it joins a bridge we always do the same set of operations: 1) Create the vFID, if not already created 2) Setup flooding for the vFID 3) Map the {Port, VID} to the vFID When a vPort is destroyed or when it leaves a bridge the reverse is performed. Encapsulate the above in join / leave functions and simplify the code. FIDs and rFIDs will use a similar set of functions. Signed-off-by: -
Ido Schimmel authored
Up until now we had a dedicated struct only for vFIDs, but before introducing support for L3 interfaces we need to make it generic and use it for all three types of FIDs: 1) FIDs - 0..4K-1, used for the VLAN-aware bridge 2) vFIDs - 4K..15K-1, used for VLAN-unaware bridges 3) rFIDs - 15K..16K-1, used to direct traffic to / from the router in the device. Will be introduced later in the series. The three types of L3 interfaces - Router InterFaces, RIFs - that will be introduced correspond to the three types of FIDs and are configured using them. Therefore, we'll need to store the links between them as well as a reference count on the underlying FID, so that the corresponding RIF will be destroyed when it reaches zero. Note that the lower 0.5K vFIDs are currently used for for non-bridged netdevs, so that traffic could be flooded to the CPU port. However, when rFIDs will be introduced we'll no longer need these and they too will be used for VLAN-unaware bridges. Make the vFID struct generic by renaming it and some of its fields. FIDs will be converted to use it later in the series. Signed-off-by:
-
Ido Schimmel authored
Use a FID index instead of vFID and ease the transition towards a generic FID struct. Signed-off-by:
-
Ido Schimmel authored
A FID used by a vPort (vFID, but also rFID later in the series) is always mapped using {Port, VID} and not only VID as with the 4K FIDs of the VLAN-aware bridge. Instead of specifying all the arguments each time, just wrap this operation using a dedicated function and simplify the code. As before, the function takes FID as its argument in preparation for a generic FID struct. Signed-off-by: -
Ido Schimmel authored
Simplify the code and use only one function for vFID creation / destruction. Unlike before, the function receives a FID index as its argument and not a vFID index. Instead of passing 0, now one would need to pass 4K, which is the first vFID. This is the first step in creating a generic FID struct that will be used for all three types of FIDs. Signed-off-by:
-
Ido Schimmel authored
In all call sites 'only_uc' is set to false, so strip it. Signed-off-by:
-
Ido Schimmel authored
There is a macro to do this kind of declarations, so use it. Signed-off-by:
-
Ido Schimmel authored
We hold a reference count on the number of ports member in the VLAN-aware bridge, as we only support one. Instead of always incrementing / decrementing the reference count after joining / leaving the bridge, simply do this accounting in the join / leave functions. Signed-off-by:
-
Ido Schimmel authored
The argument 'br_dev' is never used, so remove it. Signed-off-by:
-
Ido Schimmel authored
When responding to unlinking CHANGEUPPER notifications we shouldn't return any value, as it's not checked by upper layers. In addition, there's nothing the driver can do in case of failure, so it should simply continue and try to free as much resources as possible and not stop on first error. Signed-off-by:
-
Ido Schimmel authored
Instead of checking for a condition and then issue the warning, just do it in one go and simplify the code. Signed-off-by:
-
Ido Schimmel authored
When upper device of a VLAN device changes we already made sure it's a bridge device in PRECHANGEUPPER, so no need to check it's a master device in CHANGEUPPER. Signed-off-by:
-
Ido Schimmel authored
When a port netdev is put under LAG it cannot have VLAN upper devices, so forbid that. The LAG device itself can have VLAN upper devices. Signed-off-by:
-
Ido Schimmel authored
We currently only support the following upper devices for port netdevs: 1) Bridge 2) LAG (bond / team) 3) VLAN Any other device is forbidden, so return an error. Signed-off-by:
-
Ido Schimmel authored
Instead of checking the error value and returning NOTIFY_BAD, just use notifier_from_errno() and simplify the code. Signed-off-by:
-
David S. Miller authored
Yisen Zhuang says: ==================== net: hns: fix some bugs in hns driver This series includes some bugs fixed. All these patches needs to be applied after the patchset about ACPI support, so this series is floated to net-next list. The patches are: > from Daode, fixes about pfc pause frame, getting coaslesce, led control logic, TSO on|off and tcam table configuration. > from Jun He, fix the potential leak to port unavailable > from Kejian, fix bug of loopback and failing to test ping6 > from Qianqian, fix the several typo in hns driver For more details, please see individual patches. ==================== Signed-off-by: -
Daode Huang authored
When enable/disable tso, the driver tries to access the hardware register, but this operation will cause the port unavalible when there is traffic. This patch tries to enable TSO when initialize, then control tso through TSE bit in transmit descriptor. Signed-off-by:
Daode Huang <huangdaode@hisilicon.com> Signed-off-by:
Yisen Zhuang <Yisen.Zhuang@huawei.com> Signed-off-by:
-
Daode Huang authored
The default coalesce timeout is 3us, which is will cause CPU usage is too high. This patch change it to 50us in order to reduce CPU usage and the value makes sure network latency also meets requirement. Signed-off-by:
-
Daode Huang authored
The default sbm config parameter leaves little buffer when there is heavy traffic, which will cause packets drop. This patch changes them to make enough buffers for handling packets. Signed-off-by:
-
Jun He authored
When hns_nic_poll_rx_skb alloc skb fail, it will break receive cycle and read new fbd_num to start new receive cycle. It recomputes cycle num is fbd_num minus clean_count, actually this cycle num is too big because it drop out receive cycle. It brings about the port unavailable. So we will goto out when alloc skb fail to fix this bug. Signed-off-by:
Jun He <hjat2005@huawei.com> Signed-off-by:
Ding Tianhong <dingtianhong@huawei.com> Signed-off-by:
-
Daode Huang authored
The default driver sets anchor led bit to 0 when link down, actually, the anchor bit should be set to 1, so fixes it when link status is down. Secondly, change the return value of cpld_set_led_id to 0, which means leave the cpld to control led blink frequece other than the driver itself. Signed-off-by:
-
