- 07 Apr, 2017 11 commits
-
-
Andi Kleen authored
commit 725fc629 upstream. Linux preallocates the task structs of the idle tasks for all possible CPUs. This currently means they all end up on node 0. This also implies that the cache line of MWAIT, which is around the flags field in the task struct, are all located in node 0. We see a noticeable performance improvement on Knights Landing CPUs when the cache lines used for MWAIT are located in the local nodes of the CPUs using them. I would expect this to give a (likely slight) improvement on other systems too. The patch implements placing the idle task in the node of its CPUs, by passing the right target node to copy_process() [js] to tls in copy_process in 3.12 yet [akpm@linux-foundation.org: use NUMA_NO_NODE, not a bare -1] Link: http://lkml.kernel.org/r/1463492694-15833-1-git-send-email-andi@firstfloor.orgSigned-off-by:
Andi Kleen <ak@linux.intel.com> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Cc: Sumit Semwal <sumit.semwal@linaro.org> Signed-off-by:
Jiri Slaby <jslaby@suse.cz>
-
Sebastian Ott authored
commit dba59909 upstream. After a failure during registration of the dma_table (because of the function being in error state) we free its memory but don't reset the associated pointer to zero. When we then receive a notification from firmware (about the function being in error state) we'll try to walk and free the dma_table again. Fix this by resetting the dma_table pointer. In addition to that make sure that we free the iommu_bitmap when appropriate. Signed-off-by:
Sebastian Ott <sebott@linux.vnet.ibm.com> Reviewed-by:
Gerald Schaefer <gerald.schaefer@de.ibm.com> Signed-off-by:
Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Sumit Semwal <sumit.semwal@linaro.org> Signed-off-by:
-
Thomas Huth authored
commit 708e75a3 upstream. If kvmppc_handle_exit_pr() calls kvmppc_emulate_instruction() to emulate one instruction (in the BOOK3S_INTERRUPT_H_EMUL_ASSIST case), it calls kvmppc_core_queue_program() afterwards if kvmppc_emulate_instruction() returned EMULATE_FAIL, so the guest gets an program interrupt for the illegal opcode. However, the kvmppc_emulate_instruction() also tried to inject a program exception for this already, so the program interrupt gets injected twice and the return address in srr0 gets destroyed. All other callers of kvmppc_emulate_instruction() are also injecting a program interrupt, and since the callers have the right knowledge about the srr1 flags that should be used, it is the function kvmppc_emulate_instruction() that should _not_ inject program interrupts, so remove the kvmppc_core_queue_program() here. This fixes the issue discovered by Laurent Vivier with kvm-unit-tests where the logs are filled with these messages when the test tries to execute an illegal instruction: Couldn't emulate instruction 0x00000000 (op 0 xop 0) kvmppc_handle_exit_pr: emulation at 700 failed (00000000) Signed-off-by:
Thomas Huth <thuth@redhat.com> Reviewed-by:
Alexander Graf <agraf@suse.de> Tested-by:
Laurent Vivier <lvivier@redhat.com> Signed-off-by:
Paul Mackerras <paulus@ozlabs.org> Cc: Sumit Semwal <sumit.semwal@linaro.org> Signed-off-by:
-
Vitaly Kuznetsov authored
commit a9f61ca7 upstream. When we crash from NMI context (e.g. after NMI injection from host when 'sysctl -w kernel.unknown_nmi_panic=1' is set) we hit kernel BUG at mm/vmalloc.c:1530! as vfree() is denied. While the issue could be solved with in_nmi() check instead I opted for skipping vfree on all sorts of crashes to reduce the amount of work which can cause consequent crashes. We don't really need to free anything on crash. [js] no tsc and kexec in 3.12 yet Signed-off-by:
Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by:
K. Y. Srinivasan <kys@microsoft.com> Cc: Sumit Semwal <sumit.semwal@linaro.org> Signed-off-by:
-
Vitaly Kuznetsov authored
commit 77c0c973 upstream. When we iterate through all HA regions in handle_pg_range() we have an assumption that all these regions are sorted in the list and the 'start_pfn >= has->end_pfn' check is enough to find the proper region. Unfortunately it's not the case with WS2016 where host can hot-add regions in a different order. We end up modifying the wrong HA region and crashing later on pages online. Modify the check to make sure we found the region we were searching for while iterating. Fix the same check in pfn_covered() as well. Signed-off-by:
-
Alex Hung authored
commit e34fbbac upstream. Some system supports hybrid graphics and its discrete VGA does not have any connectors and therefore has no _DOD method. Signed-off-by:
Alex Hung <alex.hung@canonical.com> Reviewed-by:
Aaron Lu <aaron.lu@intel.com> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Cc: Sumit Semwal <sumit.semwal@linaro.org> Signed-off-by:
-
Wang, Rui Y authored
commit 1a078340 upstream. cryptd_create_hash() fails by returning -EINVAL. It is because after 8996eafd ("crypto: ahash - ensure statesize is non-zero") all ahash drivers must have a non-zero statesize. This patch fixes the problem by properly assigning the statesize. Signed-off-by:
Rui Wang <rui.y.wang@intel.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Cc: Sumit Semwal <sumit.semwal@linaro.org> Signed-off-by:
-
Wang, Rui Y authored
commit 3a020a72 upstream. ghash_clmulni_intel fails to load on Linux 4.3+ with the following message: "modprobe: ERROR: could not insert 'ghash_clmulni_intel': Invalid argument" After 8996eafd ("crypto: ahash - ensure statesize is non-zero") all ahash drivers are required to implement import()/export(), and must have a non- zero statesize. This patch has been tested with the algif_hash interface. The calculated digest values, after several rounds of import()s and export()s, match those calculated by tcrypt. Signed-off-by:
-
Florian Westphal authored
commit d1b4c689 upstream. mmapped netlink has a number of unresolved issues: - TX zerocopy support had to be disabled more than a year ago via commit 4682a035 ("netlink: Always copy on mmap TX.") because the content of the mmapped area can change after netlink attribute validation but before message processing. - RX support was implemented mainly to speed up nfqueue dumping packet payload to userspace. However, since commit ae08ce00 ("netfilter: nfnetlink_queue: zero copy support") we avoid one copy with the socket-based interface too (via the skb_zerocopy helper). The other problem is that skbs attached to mmaped netlink socket behave different from normal skbs: - they don't have a shinfo area, so all functions that use skb_shinfo() (e.g. skb_clone) cannot be used. - reserving headroom prevents userspace from seeing the content as it expects message to start at skb->head. See for instance commit aa3a0220 ("netlink: not trim skb for mmaped socket when dump"). - skbs handed e.g. to netlink_ack must have non-NULL skb->sk, else we crash because it needs the sk to check if a tx ring is attached. Also not obvious, leads to non-intuitive bug fixes such as 7c7bdf35 ("netfilter: nfnetlink: use original skbuff when acking batches"). mmaped netlink also didn't play nicely with the skb_zerocopy helper used by nfqueue and openvswitch. Daniel Borkmann fixed this via commit 6bb0fef4 ("netlink, mmap: fix edge-case leakages in nf queue zero-copy")' but at the cost of also needing to provide remaining length to the allocation function. nfqueue also has problems when used with mmaped rx netlink: - mmaped netlink doesn't allow use of nfqueue batch verdict messages. Problem is that in the mmap case, the allocation time also determines the ordering in which the frame will be seen by userspace (A allocating before B means that A is located in earlier ring slot, but this also means that B might get a lower sequence number then A since seqno is decided later. To fix this we would need to extend the spinlocked region to also cover the allocation and message setup which isn't desirable. - nfqueue can now be configured to queue large (GSO) skbs to userspace. Queing GSO packets is faster than having to force a software segmentation in the kernel, so this is a desirable option. However, with a mmap based ring one has to use 64kb per ring slot element, else mmap has to fall back to the socket path (NL_MMAP_STATUS_COPY) for all large packets. To use the mmap interface, userspace not only has to probe for mmap netlink support, it also has to implement a recv/socket receive path in order to handle messages that exceed the size of an rx ring element. Cc: Daniel Borkmann <daniel@iogearbox.net> Cc: Ken-ichirou MATSUZAWA <chamaken@gmail.com> Cc: Pablo Neira Ayuso <pablo@netfilter.org> Cc: Patrick McHardy <kaber@trash.net> Cc: Thomas Graf <tgraf@suug.ch> Signed-off-by:
Florian Westphal <fw@strlen.de> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Darrick J. Wong authored
Commit ef388e20 upstream. The on-disk field di_size is used to set i_size, which is a signed integer of loff_t. If the high bit of di_size is set, we'll end up with a negative i_size, which will cause all sorts of problems. Since the VFS won't let us create a file with such length, we should catch them here in the verifier too. [nborisov: Backported to 3.12] Signed-off-by:
Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by:
Dave Chinner <dchinner@redhat.com> Signed-off-by:
Dave Chinner <david@fromorbit.com> Signed-off-by:
Nikolay Borisov <nborisov@suse.com> Signed-off-by:
-
Eric Sandeen authored
commit 4dfce57d upstream. There have been several reports over the years of NULL pointer dereferences in xfs_trans_log_inode during xfs_fsr processes, when the process is doing an fput and tearing down extents on the temporary inode, something like: BUG: unable to handle kernel NULL pointer dereference at 0000000000000018 PID: 29439 TASK: ffff880550584fa0 CPU: 6 COMMAND: "xfs_fsr" [exception RIP: xfs_trans_log_inode+0x10] #9 [ffff8800a57bbbe0] xfs_bunmapi at ffffffffa037398e [xfs] As it turns out, this is because the i_itemp pointer, along with the d_ops pointer, has been overwritten with zeros when we tear down the extents during truncate. When the in-core inode fork on the temporary inode used by xfs_fsr was originally set up during the extent swap, we mistakenly looked at di_nextents to determine whether all extents fit inline, but this misses extents generated by speculative preallocation; we should be using if_bytes instead. This mistake corrupts the in-memory inode, and code in xfs_iext_remove_inline eventually gets bad inputs, causing it to memmove and memset incorrect ranges; this became apparent because the two values in ifp->if_u2.if_inline_ext[1] contained what should have been in d_ops and i_itemp; they were memmoved due to incorrect array indexing and then the original locations were zeroed with memset, again due to an array overrun. Fix this by properly using i_df.if_bytes to determine the number of extents, not di_nextents. Thanks to dchinner for looking at this with me and spotting the root cause. [nborisov: Backported to 3.12] Signed-off-by:
Eric Sandeen <sandeen@redhat.com> Reviewed-by:
Brian Foster <bfoster@redhat.com> Signed-off-by:
-
- 28 Mar, 2017 29 commits
-
-
Zhaohongjiang authored
Commit 5cb13dcd upstream. When I ran xfstest/073 case, the remount process was blocked to wait transactions to be zero. I found there was a io error happened, and the setfilesize transaction was not released properly. We should add the changes to cancel the io error in this case. Reproduction steps: 1. dd if=/dev/zero of=xfs1.img bs=1M count=2048 2. mkfs.xfs xfs1.img 3. losetup -f ./xfs1.img /dev/loop0 4. mount -t xfs /dev/loop0 /home/test_dir/ 5. mkdir /home/test_dir/test 6. mkfs.xfs -dfile,name=image,size=2g 7. mount -t xfs -o loop image /home/test_dir/test 8. cp a file bigger than 2g to /home/test_dir/test 9. mount -t xfs -o remount,ro /home/test_dir/test [ dchinner: moved io error detection to xfs_setfilesize_ioend() after transaction context restoration. ] [ nborisov: Adjusted context for 3.12 ] Signed-off-by:
Zhao Hongjiang <zhaohongjiang@huawei.com> Signed-off-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
-
Linus Torvalds authored
commit 474c9015 upstream. gcc-7 has an "optimization" pass that completely screws up, and generates the code expansion for the (impossible) case of calling ilog2() with a zero constant, even when the code gcc compiles does not actually have a zero constant. And we try to generate a compile-time error for anybody doing ilog2() on a constant where that doesn't make sense (be it zero or negative). So now gcc7 will fail the build due to our sanity checking, because it created that constant-zero case that didn't actually exist in the source code. There's a whole long discussion on the kernel mailing about how to work around this gcc bug. The gcc people themselevs have discussed their "feature" in https://gcc.gnu.org/bugzilla/show_bug.cgi?id=72785 but it's all water under the bridge, because while it looked at one point like it would be solved by the time gcc7 was released, that was not to be. So now we have to deal with this compiler braindamage. And the only simple approach seems to be to just delete the code that tries to warn about bad uses of ilog2(). So now "ilog2()" will just return 0 not just for the value 1, but for any non-positive value too. It's not like I can recall anybody having ever actually tried to use this function on any invalid value, but maybe the sanity check just meant that such code never made it out in public. [js] no tools/include/linux/log2.h copy of that yet Reported-by:
Laura Abbott <labbott@redhat.com> Cc: John Stultz <john.stultz@linaro.org>, Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by:
-
Peter Zijlstra authored
commit 9bbb25af upstream. Thomas spotted that fixup_pi_state_owner() can return errors and we fail to unlock the rt_mutex in that case. Reported-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by:
Darren Hart <dvhart@linux.intel.com> Cc: juri.lelli@arm.com Cc: bigeasy@linutronix.de Cc: xlpang@redhat.com Cc: rostedt@goodmis.org Cc: mathieu.desnoyers@efficios.com Cc: jdesfossez@efficios.com Cc: dvhart@infradead.org Cc: bristot@redhat.com Link: http://lkml.kernel.org/r/20170304093558.867401760@infradead.orgSigned-off-by:
-
Peter Zijlstra authored
commit c236c8e9 upstream. While working on the futex code, I stumbled over this potential use-after-free scenario. Dmitry triggered it later with syzkaller. pi_mutex is a pointer into pi_state, which we drop the reference on in unqueue_me_pi(). So any access to that pointer after that is bad. Since other sites already do rt_mutex_unlock() with hb->lock held, see for example futex_lock_pi(), simply move the unlock before unqueue_me_pi(). Reported-by:
Dmitry Vyukov <dvyukov@google.com> Signed-off-by:
-
Roman Mashak authored
[ Upstream commit edb9d1bf ] When tc actions are loaded as a module and no actions have been installed, flushing them would result in actions removed from the memory, but modules reference count not being decremented, so that the modules would not be unloaded. Following is example with GACT action: % sudo modprobe act_gact % lsmod Module Size Used by act_gact 16384 0 % % sudo tc actions ls action gact % % sudo tc actions flush action gact % lsmod Module Size Used by act_gact 16384 1 % sudo tc actions flush action gact % lsmod Module Size Used by act_gact 16384 2 % sudo rmmod act_gact rmmod: ERROR: Module act_gact is in use .... After the fix: % lsmod Module Size Used by act_gact 16384 0 % % sudo tc actions add action pass index 1 % sudo tc actions add action pass index 2 % sudo tc actions add action pass index 3 % lsmod Module Size Used by act_gact 16384 3 % % sudo tc actions flush action gact % lsmod Module Size Used by act_gact 16384 0 % % sudo tc actions flush action gact % lsmod Module Size Used by act_gact 16384 0 % sudo rmmod act_gact % lsmod Module Size Used by % Fixes: f97017cd ("net-sched: Fix actions flushing") Signed-off-by:
Roman Mashak <mrv@mojatatu.com> Signed-off-by:
Jamal Hadi Salim <jhs@mojatatu.com> Acked-by:
Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by:
-
Hannes Frederic Sowa authored
[ Upstream commit 72ef9c41 ] This patch fixes a memory leak, which happens if the connection request is not fulfilled between parsing the DCCP options and handling the SYN (because e.g. the backlog is full), because we forgot to free the list of ack vectors. Reported-by:
Jianwen Ji <jiji@redhat.com> Signed-off-by:
Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by:
-
Jon Maxwell authored
[ Upstream commit 45caeaa5 ] As Eric Dumazet pointed out this also needs to be fixed in IPv6. v2: Contains the IPv6 tcp/Ipv6 dccp patches as well. We have seen a few incidents lately where a dst_enty has been freed with a dangling TCP socket reference (sk->sk_dst_cache) pointing to that dst_entry. If the conditions/timings are right a crash then ensues when the freed dst_entry is referenced later on. A Common crashing back trace is: #8 [] page_fault at ffffffff8163e648 [exception RIP: __tcp_ack_snd_check+74] . . #9 [] tcp_rcv_established at ffffffff81580b64 #10 [] tcp_v4_do_rcv at ffffffff8158b54a #11 [] tcp_v4_rcv at ffffffff8158cd02 #12 [] ip_local_deliver_finish at ffffffff815668f4 #13 [] ip_local_deliver at ffffffff81566bd9 #14 [] ip_rcv_finish at ffffffff8156656d #15 [] ip_rcv at ffffffff81566f06 #16 [] __netif_receive_skb_core at ffffffff8152b3a2 #17 [] __netif_receive_skb at ffffffff8152b608 #18 [] netif_receive_skb at ffffffff8152b690 #19 [] vmxnet3_rq_rx_complete at ffffffffa015eeaf [vmxnet3] #20 [] vmxnet3_poll_rx_only at ffffffffa015f32a [vmxnet3] #21 [] net_rx_action at ffffffff8152bac2 #22 [] __do_softirq at ffffffff81084b4f #23 [] call_softirq at ffffffff8164845c #24 [] do_softirq at ffffffff81016fc5 #25 [] irq_exit at ffffffff81084ee5 #26 [] do_IRQ at ffffffff81648ff8 Of course it may happen with other NIC drivers as well. It's found the freed dst_entry here: 224 static bool tcp_in_quickack_mode(struct sock *sk)
↩ 225 {↩ 226 ▹ const struct inet_connection_sock *icsk = inet_csk(sk);↩ 227 ▹ const struct dst_entry *dst = __sk_dst_get(sk);↩ 228↩ 229 ▹ return (dst && dst_metric(dst, RTAX_QUICKACK)) ||↩ 230 ▹ ▹ (icsk->icsk_ack.quick && !icsk->icsk_ack.pingpong);↩ 231 }↩ But there are other backtraces attributed to the same freed dst_entry in netfilter code as well. All the vmcores showed 2 significant clues: - Remote hosts behind the default gateway had always been redirected to a different gateway. A rtable/dst_entry will be added for that host. Making more dst_entrys with lower reference counts. Making this more probable. - All vmcores showed a postitive LockDroppedIcmps value, e.g: LockDroppedIcmps 267 A closer look at the tcp_v4_err() handler revealed that do_redirect() will run regardless of whether user space has the socket locked. This can result in a race condition where the same dst_entry cached in sk->sk_dst_entry can be decremented twice for the same socket via: do_redirect()->__sk_dst_check()-> dst_release(). Which leads to the dst_entry being prematurely freed with another socket pointing to it via sk->sk_dst_cache and a subsequent crash. To fix this skip do_redirect() if usespace has the socket locked. Instead let the redirect take place later when user space does not have the socket locked. The dccp/IPv6 code is very similar in this respect, so fixing it there too. As Eric Garver pointed out the following commit now invalidates routes. Which can set the dst->obsolete flag so that ipv4_dst_check() returns null and triggers the dst_release(). Fixes: ceb33206 ("ipv4: Kill routes during PMTU/redirect updates.") Cc: Eric Garver <egarver@redhat.com> Cc: Hannes Sowa <hsowa@redhat.com> Signed-off-by:Jon Maxwell <jmaxwell37@gmail.com> Signed-off-by:
-
Florian Westphal authored
[ Upstream commit 79e49503 ] ip6_fragment, in case skb has a fraglist, checks if the skb is cloned. If it is, it will move to the 'slow path' and allocates new skbs for each fragment. However, right before entering the slowpath loop, it updates the nexthdr value of the last ipv6 extension header to NEXTHDR_FRAGMENT, to account for the fragment header that will be inserted in the new ipv6-fragment skbs. In case original skb is cloned this munges nexthdr value of another skb. Avoid this by doing the nexthdr update for each of the new fragment skbs separately. This was observed with tcpdump on a bridge device where netfilter ipv6 reassembly is active: tcpdump shows malformed fragment headers as the l4 header (icmpv6, tcp, etc). is decoded as a fragment header. Cc: Hannes Frederic Sowa <hannes@stressinduktion.org> Reported-by:
Andreas Karis <akaris@redhat.com> Signed-off-by:
-
Dmitry V. Levin authored
[ Upstream commit 745cb7f8 ] Replace MAX_ADDR_LEN with its numeric value to fix the following linux/packet_diag.h userspace compilation error: /usr/include/linux/packet_diag.h:67:17: error: 'MAX_ADDR_LEN' undeclared here (not in a function) __u8 pdmc_addr[MAX_ADDR_LEN]; This is not the first case in the UAPI where the numeric value of MAX_ADDR_LEN is used instead of symbolic one, uapi/linux/if_link.h already does the same: $ grep MAX_ADDR_LEN include/uapi/linux/if_link.h __u8 mac[32]; /* MAX_ADDR_LEN */ There are no UAPI headers besides these two that use MAX_ADDR_LEN. Signed-off-by:
Dmitry V. Levin <ldv@altlinux.org> Acked-by:
Pavel Emelyanov <xemul@virtuozzo.com> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 02b2faaf ] Dmitry Vyukov reported a divide by 0 triggered by syzkaller, exploiting tcp_disconnect() path that was never really considered and/or used before syzkaller ;) I was not able to reproduce the bug, but it seems issues here are the three possible actions that assumed they would never trigger on a listener. 1) tcp_write_timer_handler 2) tcp_delack_timer_handler 3) MTU reduction Only IPv6 MTU reduction was properly testing TCP_CLOSE and TCP_LISTEN states from tcp_v6_mtu_reduced() Signed-off-by:
Eric Dumazet <edumazet@google.com> Reported-by:
-
Arnaldo Carvalho de Melo authored
[ Upstream commit d5afb6f9 ] The code where sk_clone() came from created a new socket and locked it, but then, on the error path didn't unlock it. This problem stayed there for a long while, till b0691c8e ("net: Unlock sock before calling sk_free()") fixed it, but unfortunately the callers of sk_clone() (now sk_clone_locked()) were not audited and the one in dccp_create_openreq_child() remained. Now in the age of the syskaller fuzzer, this was finally uncovered, as reported by Dmitry: ---- 8< ---- I've got the following report while running syzkaller fuzzer on 86292b33 ("Merge branch 'akpm' (patches from Andrew)") [ BUG: held lock freed! ] 4.10.0+ #234 Not tainted ------------------------- syz-executor6/6898 is freeing memory ffff88006286cac0-ffff88006286d3b7, with a lock still held there! (slock-AF_INET6){+.-...}, at: [<ffffffff8362c2c9>] spin_lock include/linux/spinlock.h:299 [inline] (slock-AF_INET6){+.-...}, at: [<ffffffff8362c2c9>] sk_clone_lock+0x3d9/0x12c0 net/core/sock.c:1504 5 locks held by syz-executor6/6898: #0: (sk_lock-AF_INET6){+.+.+.}, at: [<ffffffff839a34b4>] lock_sock include/net/sock.h:1460 [inline] #0: (sk_lock-AF_INET6){+.+.+.}, at: [<ffffffff839a34b4>] inet_stream_connect+0x44/0xa0 net/ipv4/af_inet.c:681 #1: (rcu_read_lock){......}, at: [<ffffffff83bc1c2a>] inet6_csk_xmit+0x12a/0x5d0 net/ipv6/inet6_connection_sock.c:126 #2: (rcu_read_lock){......}, at: [<ffffffff8369b424>] __skb_unlink include/linux/skbuff.h:1767 [inline] #2: (rcu_read_lock){......}, at: [<ffffffff8369b424>] __skb_dequeue include/linux/skbuff.h:1783 [inline] #2: (rcu_read_lock){......}, at: [<ffffffff8369b424>] process_backlog+0x264/0x730 net/core/dev.c:4835 #3: (rcu_read_lock){......}, at: [<ffffffff83aeb5c0>] ip6_input_finish+0x0/0x1700 net/ipv6/ip6_input.c:59 #4: (slock-AF_INET6){+.-...}, at: [<ffffffff8362c2c9>] spin_lock include/linux/spinlock.h:299 [inline] #4: (slock-AF_INET6){+.-...}, at: [<ffffffff8362c2c9>] sk_clone_lock+0x3d9/0x12c0 net/core/sock.c:1504 Fix it just like was done by b0691c8e ("net: Unlock sock before calling sk_free()"). Reported-by:
Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 13baa00a ] It is now very clear that silly TCP listeners might play with enabling/disabling timestamping while new children are added to their accept queue. Meaning net_enable_timestamp() can be called from BH context while current state of the static key is not enabled. Lets play safe and allow all contexts. The work queue is scheduled only under the problematic cases, which are the static key enable/disable transition, to not slow down critical paths. This extends and improves what we did in commit 5fa8bbda ("net: use a work queue to defer net_disable_timestamp() work") Fixes: b90e5794 ("net: dont call jump_label_dec from irq context") Signed-off-by:
-
Alexander Potapenko authored
[ Upstream commit 540e2894 ] KMSAN (KernelMemorySanitizer, a new error detection tool) reports use of uninitialized memory in packet_bind_spkt(): Acked-by:
Alexander Potapenko <glider@google.com> Signed-off-by:
-
Paul Hüber authored
[ Upstream commit 51fb60eb ] l2tp_ip_backlog_recv may not return -1 if the packet gets dropped. The return value is passed up to ip_local_deliver_finish, which treats negative values as an IP protocol number for resubmission. Signed-off-by:
Paul Hüber <phueber@kernsp.in> Signed-off-by:
-
Julian Anastasov authored
[ Upstream commit 6e28099d ] Restore the lost masking of TOS in input route code to allow ip rules to match it properly. Problem [1] noticed by Shmulik Ladkani <shmulik.ladkani@gmail.com> [1] http://marc.info/?t=137331755300040&r=1&w=2 Fixes: 89aef892 ("ipv4: Delete routing cache.") Signed-off-by:
Julian Anastasov <ja@ssi.bg> Signed-off-by:
-
Matthias Schiffer authored
[ Upstream commit 4e37d691 ] The incorrect check caused an off-by-one error: the maximum VID 0xffffff was unusable. Fixes: d342894c ("vxlan: virtual extensible lan") Signed-off-by:
Matthias Schiffer <mschiffer@universe-factory.net> Acked-by:
Jiri Benc <jbenc@redhat.com> Signed-off-by:
-
Peter Zijlstra authored
commit e33886b3 upstream. Add two helpers to make it easier to treat the refcount as boolean. [js] do not involve WARN_ON_ONCE as it causes build failures Suggested-by:
Jason Baron <jasonbaron0@gmail.com> Signed-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Luis de Bethencourt authored
commit 7789cd39 upstream. Fix a smatch warning: drivers/scsi/mvsas/mv_sas.c:740 mvs_task_prep() warn: curly braces intended? The code is correct, the indention is misleading. When the device is not ready we want to return SAS_PHY_DOWN. But current indentation makes it look like we only do so in the else branch of if (mvi_dev). Signed-off-by:
Luis de Bethencourt <luisbg@osg.samsung.com> Reviewed-by:
Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Johan Hovold authored
commit 654b404f upstream. Add missing sanity check to the bulk-in completion handler to avoid an integer underflow that can be triggered by a malicious device. This avoids leaking 128 kB of memory content from after the URB transfer buffer to user space. Fixes: 8c209e67 ("USB: make actual_length in struct urb field u32") Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Johan Hovold authored
commit 0b1d250a upstream. Fix a NULL-pointer dereference in the interrupt callback should a malicious device send data containing a bad port number by adding the missing sanity check. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
-
Johan Hovold authored
commit de46e566 upstream. Make sure to verify that we have the required interrupt-out endpoint for IOWarrior56 devices to avoid dereferencing a NULL-pointer in write should a malicious device lack such an endpoint. Fixes: 946b960d ("USB: add driver for iowarrior devices.") Signed-off-by:
-
Johan Hovold authored
commit b7321e81 upstream. Make sure to check for the required interrupt-in endpoint to avoid dereferencing a NULL-pointer should a malicious device lack such an endpoint. Note that a fairly recent change purported to fix this issue, but added an insufficient test on the number of endpoints only, a test which can now be removed. Fixes: 4ec0ef3a ("USB: iowarrior: fix oops with malicious USB descriptors") Fixes: 946b960d ("USB: add driver for iowarrior devices.") Signed-off-by:
-
Johan Hovold authored
commit 30572418 upstream. This driver needlessly took another reference to the tty on open, a reference which was then never released on close. This lead to not just a leak of the tty, but also a driver reference leak that prevented the driver from being unloaded after a port had once been opened. Fixes: 4a90f09b ("tty: usb-serial krefs") Signed-off-by:
-
Johan Hovold authored
commit 8c76d7cd upstream. Add missing sanity check to the bulk-in completion handler to avoid an integer underflow that could be triggered by a malicious device. This avoids leaking up to 56 bytes from after the URB transfer buffer to user space. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
-
Guenter Roeck authored
commit dcc7620c upstream. Upstream commit 98d74f9c ("xhci: fix 10 second timeout on removal of PCI hotpluggable xhci controllers") fixes a problem with hot pluggable PCI xhci controllers which can result in excessive timeouts, to the point where the system reports a deadlock. The same problem is seen with hot pluggable xhci controllers using the xhci-plat driver, such as the driver used for Type-C ports on rk3399. Similar to hot-pluggable PCI controllers, the driver for this chip removes the xhci controller from the system when the Type-C cable is disconnected. The solution for PCI devices works just as well for non-PCI devices and avoids the problem. Signed-off-by:
Guenter Roeck <linux@roeck-us.net> Signed-off-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by:
-
Felipe Balbi authored
commit 7369090a upstream. Some gadget drivers are bad, bad boys. We notice that ADB was passing bad Burst Size which caused top bits of param0 to be overwritten which confused DWC3 when running this command. In order to avoid future issues, we're going to make sure values passed by macros are always safe for the controller. Note that ADB still needs a fix to *not* pass bad values. Reported-by:
Mohamed Abbas <mohamed.abbas@intel.com> Sugested-by:
Adam Andruszak <adam.andruszak@intel.com> Signed-off-by:
Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by:
-
Rik van Riel authored
commit bf7165cf upstream. There are several trace include files that define TRACE_INCLUDE_FILE. Include several of them in the same .c file (as I currently have in some code I am working on), and the compile will blow up with a "warning: "TRACE_INCLUDE_FILE" redefined #define TRACE_INCLUDE_FILE syscalls" Every other include file in include/trace/events/ avoids that issue by having a #undef TRACE_INCLUDE_FILE before the #define; syscalls.h should have one, too. Link: http://lkml.kernel.org/r/20160928225554.13bd7ac6@annuminas.surriel.com Fixes: b8007ef7 ("tracing: Separate raw syscall from syscall tracer") Signed-off-by:
Rik van Riel <riel@redhat.com> Signed-off-by:
Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by:
-
Ralf Baechle authored
commit 3021773c upstream. When expanding the la or dla pseudo-instruction in a delay slot the GNU assembler will complain should the pseudo-instruction expand to multiple actual instructions, since only the first of them will be in the delay slot leading to the pseudo-instruction being only partially executed if the branch is taken. Use of PTR_LA in the dec int-handler.S leads to such warnings: arch/mips/dec/int-handler.S: Assembler messages: arch/mips/dec/int-handler.S:149: Warning: macro instruction expanded into multiple instructions in a branch delay slot arch/mips/dec/int-handler.S:198: Warning: macro instruction expanded into multiple instructions in a branch delay slot Avoid this by open coding the PTR_LA macros. Signed-off-by:
Ralf Baechle <ralf@linux-mips.org> Signed-off-by:
-
Arnd Bergmann authored
commit d43e6fb4 upstream. The #warning was present 10 years ago when the driver first got merged. As the platform is rather obsolete by now, it seems very unlikely that the warning will cause anyone to fix the code properly. kernelci.org reports the warning for every build in the meantime, so I think it's better to just turn it into a code comment to reduce noise. Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
