- 31 Mar, 2010 40 commits
-
-
Jouni Malinen authored
mac80211 skips drop_unencrypted checks if the driver/firmware has already taken care of this. In case of ath9k, we must not indicate that the frame was decrypted if no decryption was actually done. Signed-off-by:
Jouni Malinen <j@w1.fi> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Jouni Malinen authored
When selecting the RX key for group-addressed robust management frames, we do not actually select any BIP key if the frame is unprotected (since we cannot find the key index from MMIE). This results in the drop_unencrypted check in failing to drop the frame. It is enough to verify that we have a STA entry for the transmitter and that MFP is enabled for that STA; we do not need to check rx->key here. This fixes BIP processing for unprotected, group-addressed, robust management frames. Signed-off-by:
-
Jouni Malinen authored
BIP (part of IEEE 802.11w) is only supposed to be used with group-addressed frames. We ended up picking it as a default mechanism for every management whenever we did not have a STA entry for the destination (e.g., for Probe Response to a STA that is not associated). While the extra MMIE in the end of management frames should not break frames completed in most cases, there is no point in doing this. Fix key selection to pick the default management key only if the frame is sent to multicast/broadcast address and the frame is a robust management frame. Signed-off-by:
-
Jouni Malinen authored
When management frame protection (IEEE 802.11w) is used, the deauthentication and disassociation frames must be protected whenever the encryption keys are configured. We were removing the STA entry and with it, the keys, just before actually sending out these frames which meant that the frames went out unprotected. The AP will drop them in such a case. Fix this by reordering the operations a bit so that sta_info_destroy_addr() gets called only after ieee80211_send_deauth_disassoc(). Signed-off-by:
-
Jouni Malinen authored
Calculate a running average of the signal strength reported for Beacon frames and indicate cqm events if the average value moves below or above the configured threshold value (and filter out repetitive events with by using the configured hysteresis). Signed-off-by:
-
Sujith authored
Set IEEE80211_HW_RX_INCLUDES_FCS to indicate that the FCS is present in RX frames. Also, remove a redundant assignment of skb length and include the FCS_LEN when checking padding. Fixing this issue makes TKIP work. Signed-off-by:
Sujith <Sujith.Manoharan@atheros.com> Signed-off-by:
-
Felix Fietkau authored
ath_tx_status and ath_rx_status data are only necessary for a short time, until they have been processed and converted into mac80211 data structures. Because of that, it makes no sense to keep them tied to the DMA descriptor, that only wastes precious memory. This patch allocates the data on stack in the functions that call the conversion functions from ath9k_hw. Signed-off-by:
Felix Fietkau <nbd@openwrt.org> Signed-off-by:
-
Felix Fietkau authored
This patch passes in a pointer to the ath_rx_status data structure for functions that need it, instead of letting them grab it directly from the ath_desc struct. This is useful for making it possible to allocate the intermediate rx status data separately. Signed-off-by:
-
Felix Fietkau authored
This patch passes in a pointer to the ath_tx_status data structure for functions that need it, instead of letting them grab it directly from the ath_desc struct. This is useful for making it possible to allocate the intermediate tx status data separately. Signed-off-by:
-
Zhu Yi authored
When a scan watchdog is fired, try to send abort scan command first before restarting the adapter. This avoids reconnection for some users when scan hang is detected. This fixed bug https://bugzilla.kernel.org/show_bug.cgi?id=15419Reported-by:
Maurizio Avogadro <mavoga@gmail.com> Tested-by:
Zhu Yi <yi.zhu@intel.com> Signed-off-by:
-
Sujith authored
Not setting the opmode properly during initialization results in the firmware sending up a bunch of packets before add_interface() has been called, for the first interface. This patch fixes the issue by setting the initial mode to 'managed'. Signed-off-by:
-
Sujith authored
Stop/restart TX queues when the internal SKB queue is full. This helps handle TX better under heavy load. Signed-off-by:
-
Sujith authored
This patch introduces the usage of URB anchors, thus reducing a large amount of code dealing with URB maintenance within the driver. The RX callback now takes care of freeing the SKB associated with each URB. Signed-off-by:
-
Sujith authored
Skip beyond the watchdog pattern properly. This fixes occasional failure of the driver to load. Signed-off-by:
-
Sujith authored
Accessing the sta pointer in TX completion without approprate RCU protection is wrong. Fix this. Also, RCU protection is needed when the station's aggregation state is updated. Handle this properly. Signed-off-by:
-
Sujith authored
The calculation of RX filter is fairly different between ath9k and ath9k_htc, trying to make this common between the two drivers would result in code churn. While at it, remove the handling of PSPOLL filter, it can be added when(if) AP support is added to ath9k_htc. Signed-off-by:
-
Stanislaw Gruszka authored
Enable QoS explicitly, when user space AP program will setup a QoS queues. Currently this is not needed as iwlwifi not work in AP mode and no other driver implement enable/disable QoS. Signed-off-by:
Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by:
-
Stanislaw Gruszka authored
We activate/deactivate QoS and setup default queue parameters in iwlwifi driver. Mac stack do the same, so we do not need repeat that work here. Stack also will tell when disable QoS, this will fix driver when working with older APs, that do not have QoS implemented. Patch make "force = true" in iwl_active_qos() assuming we always want to do with QoS what mac stack wish. Patch also remove unused qos_cap bits, do not initialize qos_active = 0, as we have it initialized to zero by kzalloc. Signed-off-by:
-
Stanislaw Gruszka authored
Add interface to disable/enable QoS (aka WMM or WME). Currently drivers enable it explicitly when ->conf_tx method is called, and newer disable. Disabling is needed for some APs, which do not support QoS, such we should send QoS frames to them. Signed-off-by:
-
Zhu Yi authored
Remove skb_linearize() in the iwlwifi drivers since mac80211 supports paged rx SKBs now. Signed-off-by:
-
Zhu Yi authored
Mac80211 drivers can now pass paged SKBs to mac80211 via ieee80211_rx{_irqsafe}. The implementation currently use skb_linearize() in a few places i.e. management frame handling, software decryption, defragmentation and A-MSDU process. We will optimize them one by one later. Signed-off-by: -
Rafał Miłecki authored
Signed-off-by:
Rafał Miłecki <zajec5@gmail.com> Signed-off-by:
-
Rafał Miłecki authored
Signed-off-by:
-
Rafał Miłecki authored
We do not want to partially change chanspec just to find out there is not entry in table for given channel. Signed-off-by:
-
Rafał Miłecki authored
Signed-off-by:
-
Rafał Miłecki authored
Signed-off-by:
-
Xose Vazquez Perez authored
Taken from latest ralink linux driver(RT3070_LinuxSTA_V2.3.0.1_20100208) All of them are RT3070 devices. Signed-off-by:
Xose Vazquez Perez <xose.vazquez@gmail.com> Acked-by:
Ivo van Doorn <IvDoorn@gmail.com> Acked-by:
Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by:
-
Xose Vazquez Perez authored
Taken from latest ralink linux driver, it's a RT3593 PCI/PCIe. Signed-off-by:
-
Xose Vazquez Perez authored
It was removed in the windows inf file by ralink. And it isn't on ralink linux drivers. Signed-off-by:
-
Xose Vazquez Perez authored
Taken from ralink linux drivers: RT3070_LinuxSTA_V2.3.0.1_20100208/common/rtusb_dev_id.c: {USB_DEVICE(0x0B05,0x1784)}, /* Asus 3072 */ RT3070_LinuxSTA_V2.3.0.1_20100208/common/rtusb_dev_id.c: {USB_DEVICE(0x13D3,0x3305)}, /* AzureWave 3070*/ RT3070_LinuxSTA_V2.3.0.1_20100208/common/rtusb_dev_id.c: {USB_DEVICE(0x07D1,0x3C16)}, /* D-Link 3070 */ RT3070_LinuxSTA_V2.3.0.1_20100208/common/rtusb_dev_id.c: {USB_DEVICE(0x203D,0x14A9)}, /* Encore 3070*/ RT3070_LinuxSTA_V2.3.0.1_20100208/common/rtusb_dev_id.c: {USB_DEVICE(0x1740,0x9707)}, /* EnGenius 3070 */ RT3070_LinuxSTA_V2.3.0.1_20100208/common/rtusb_dev_id.c: {USB_DEVICE(0x1740,0x9708)}, /* EnGenius 3071 */ RT3070_LinuxSTA_V2.3.0.1_20100208/common/rtusb_dev_id.c: {USB_DEVICE(0x1740,0x9709)}, /* EnGenius 3072 */ RT3070_LinuxSTA_V2.3.0.1_20100208/common/rtusb_dev_id.c: {USB_DEVICE(0x04BB,0x0947)}, /* I-O DATA 3070 */ RT3070_LinuxSTA_V2.3.0.1_20100208/common/rtusb_dev_id.c: {USB_DEVICE(0x04BB,0x0948)}, /* I-O DATA 3072 */ RT3070_LinuxSTA_V2.3.0.1_20100208/common/rtusb_dev_id.c: {USB_DEVICE(0x0DB0,0x3822)}, /* MSI 3070 */ RT3070_LinuxSTA_V2.3.0.1_20100208/common/rtusb_dev_id.c: {USB_DEVICE(0x0DB0,0x3821)}, /* Ralink 3070 */ RT3070_LinuxSTA_V2.3.0.1_20100208/common/rtusb_dev_id.c: {USB_DEVICE(0x0DB0,0x3870)}, /* MSI 3070*/ RT3070_LinuxSTA_V2.3.0.1_20100208/common/rtusb_dev_id.c: {USB_DEVICE(0x0DB0,0x3871)}, /* MSI 3070 */ RT3070_LinuxSTA_V2.3.0.1_20100208/common/rtusb_dev_id.c: {USB_DEVICE(0x0DB0,0x821A)}, /* Ralink 3070 */ RT3070_LinuxSTA_V2.3.0.1_20100208/common/rtusb_dev_id.c: {USB_DEVICE(0x0DB0,0x822A)}, /* MSI 3070 */ RT3070_LinuxSTA_V2.3.0.1_20100208/common/rtusb_dev_id.c: {USB_DEVICE(0x0DB0,0x870A)}, /* MSI 3070*/ RT3070_LinuxSTA_V2.3.0.1_20100208/common/rtusb_dev_id.c: {USB_DEVICE(0x0DB0,0x871A)}, /* MSI 3070 */ RT3070_LinuxSTA_V2.3.0.1_20100208/common/rtusb_dev_id.c: {USB_DEVICE(0x0DB0,0x899A)}, /* MSI 3070*/ RT3070_LinuxSTA_V2.3.0.1_20100208/common/rtusb_dev_id.c: {USB_DEVICE(0x20B8,0x8888)}, /* PARA INDUSTRIAL 3070 */ RT3070_LinuxSTA_V2.3.0.1_20100208/common/rtusb_dev_id.c: {USB_DEVICE(0x0DF6,0x0048)}, /* Sitecom 3070 */ RT3070_LinuxSTA_V2.3.0.1_20100208/common/rtusb_dev_id.c: {USB_DEVICE(0x0DF6,0x0047)}, /* Sitecom 3071 */ RT3070_LinuxSTA_V2.3.0.1_20100208/common/rtusb_dev_id.c: {USB_DEVICE(0x083A,0xA701)}, /* SMC 3070 */ RT3070_LinuxSTA_V2.3.0.1_20100208/common/rtusb_dev_id.c: {USB_DEVICE(0x083A,0xA702)}, /* SMC 3072 */ Signed-off-by: -
Saravanan Dhanabal authored
After last transmission, the device goes to sleep earlier than the configured dynamic power save timeout. If timeout is set to 400ms, device enters into sleep mode at around 330ms since from last TX. This patch removes the msleep(1), which causes the delay after ELP wakeup. Replaced with udelay(10), the variation is around 7-10ms. Signed-off-by:
Saravanan Dhanabal <ext-saravanan.dhanabal@nokia.com> Reviewed-by:
Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by:
Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by:
-
Juuso Oikarinen authored
This patch will enable the hardware keep-alive mode, configure the required template, configure keep-alive parameters, and re-order JOIN's and ACX_AID in such a way that the keep-alive is activated. Signed-off-by:
-
Juuso Oikarinen authored
Add support for keep-alive templates, which are indexed. Signed-off-by:
-
Juuso Oikarinen authored
This patch configures the mac80211 to not perform connection monitoring (periodic probe-requests) and instead rely on the hardware to do it. Signed-off-by:
-
Juuso Oikarinen authored
If PSM entry fails despite of retries, assume that the AP has been lost, and indicate connection loss to the mac80211. This is much safer than remaining in active mode. Signed-off-by:
-
Juuso Oikarinen authored
Configure a probe-request template to the wl1271 when associated - the wl1271 will use this to attempt to recover a connection when beacon loss is detected. Signed-off-by:
-
Juuso Oikarinen authored
The driver tx-queue flush operation leaks broadcast-frames. This leak occurs if the driver is shut down while there are frames in TX buffers (such as in a firmware crash scenario.) Fix the leak. Signed-off-by:
Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com> Signed-off-by:
-
Teemu Paasikivi authored
Change the driver to call ieee80211_beacon_loss function always when BSS_LOST_EVENT is received. Reason for the change is that entering PSM might fail before driver receives BSS_LOST_EVENT. In such case the driver would disable PSM and the stack would not be notified about beacon loss and connection loss detection would be delayed by tens of seconds. Signed-off-by:
-
Juuso Oikarinen authored
Configure the hardware beacon interval to whatever requested by the mac80211. Signed-off-by:
-
Juuso Oikarinen authored
Fix the driver to better reflect the ad-hoc related configuration from the mac80211. Signed-off-by:
-
