This `usb_reset_device` command has been around since the driver was
originally reverse engineered. It doesn't cause much issue on single
interface CP210x devices, but on the CP2105 and CP2108 with 2 and 4
interfaces respectively it will cause instability on enumeration and
delays enumeration noticably. There should be no reason to reset a device
at startup, per the CP210x AN571 spec.
Signed-off-by: Preston Fick <preston.fick@silabs.com>
Cc: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

OTG3 and EH Compliance Plan 1.0 talks about Super Speed OTG Verification
system (SS-OVS) which consists of an excersizer and analyzer.

USB Compliance Suite from Lecroy or Ellisys can act as such SS-OVS for
Link Layer Validation (LVS).

Some modifications are needed for an embedded Linux USB host to pass all
these tests.  Most of these tests require just Link to be in U0. They do
not work with default Linux USB stack since, default stack does port
reset and then starts sending setup packet, which is not expected by
Link Layer Validation (LVS) device of Lecroy Compliance Suit.  Then,
There are many Link Layer Tests which need host to generate specific
traffic.

This patch supports specific traffic generation cases. As of now all the
host Lecroy Link Layer-USBIF tests (except TD7.26) passes
with this patch for single run using  Lecroy USB Compliance Suite
Version 1.98 Build 239 and Lecroy USB Protocol Analyzer version 4.80
Build 1603. Therefore patch seems to be a good candidate for inclusion.
Further modification can be done on top of it.

lvstest driver will not bind to any device by default. It can bind
manually to a super speed USB host controller root hub. Therefore, regular
hub driver must be unbound before this driver is bound. For example, if
2-0:1.0 is the xhci root hub, then execute following to unbind hub driver.

 echo 2-0:1.0 > /sys/bus/usb/drivers/hub/unbind

Then write Linux Foundation's vendor ID which is used by root hubs and
SS root hub's device ID into new_id file. Writing IDs into new_id file
will also bind the lvs driver with any available SS root hub interfaces.

 echo "1D6B 3" > /sys/bus/usb/drivers/lvs/new_id

Now connect LVS device with root hub port.

Test case specific traffic can be generated as follows whenever needed:

1. To issue "Get Device descriptor" command for TD.7.06:
 echo  > /sys/bus/usb/devices/2-0\:1.0/get_dev_desc

2. To set U1 timeout to 127 for TD.7.18
 echo 127 > /sys/bus/usb/devices/2-0\:1.0/u1_timeout

3. To set U2 timeout to 0 for TD.7.18
 echo 0 > /sys/bus/usb/devices/2-0\:1.0/u2_timeout

4. To issue "Hot Reset" for TD.7.29
 echo  > /sys/bus/usb/devices/2-0\:1.0/hot_reset

5. To issue "U3 Entry" for TD.7.35
 echo  > /sys/bus/usb/devices/2-0\:1.0/u3_entry

6. To issue "U3 Exit" for TD.7.36
 echo  > /sys/bus/usb/devices/2-0\:1.0/u3_exit
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb_alloc_dev is used by lvstest driver now which can be built as
module. Therefore export usb_alloc_dev symbol.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch fixes a bug in ohci-hcd.  When an URB is unlinked, the
corresponding Endpoint Descriptor is added to the ed_rm_list and taken
off the hardware schedule.  Once the ED is no longer visible to the
hardware, finish_unlinks() handles the URBs that were unlinked or have
completed.  If any URBs remain attached to the ED, the ED is added
back to the hardware schedule -- but only if the controller is
running.

This fails when a controller dies.  A non-empty ED does not get added
back to the hardware schedule and does not remain on the ed_rm_list;
ohci-hcd loses track of it.  The remaining URBs cannot be unlinked,
which causes the USB stack to hang.

The patch changes finish_unlinks() so that non-empty EDs remain on
the ed_rm_list if the controller isn't running.  This requires moving
some of the existing code around, to avoid modifying the ED's hardware
fields more than once.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The debug routine fill_async_buffer() in ohci-hcd is buggy: It never
produces any output because it forgets to initialize the output buffer
size.  Also, the debug routine ohci_dump() has an unused argument.

This patch adds the correct initialization and removes the unused
argument.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Apparently nobody ever remembered to add Scatter-Gather support to
ohci-hcd.  This patch adds it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When a host controller dies, we don't need to wait for a driver to
time out.  We can shut down its URBs immediately.  Without this
change, we can end up waiting 30 seconds for a mass-storage transfer
to time out.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'usb-serial-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next

Johan writes:

USB-serial updates for v3.17-rc1

Here are some minor fixes and clean-ups to the ftdi_sio, mos7840 and kl5kusb105
drivers for v3.17-rc1.
Signed-off-by: Johan Hovold <johan@kernel.org>

We want those fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull ext4 bugfixes from Ted Ts'o:
 "More bug fixes for ext4 -- most importantly, a fix for a bug
  introduced in 3.15 that can end up triggering a file system corruption
  error after a journal replay.

  It shouldn't lead to any actual data corruption, but it is scary and
  can force file systems to be remounted read-only, etc"

* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: fix potential null pointer dereference in ext4_free_inode
  ext4: fix a potential deadlock in __ext4_es_shrink()
  ext4: revert commit which was causing fs corruption after journal replays
  ext4: disable synchronous transaction batching if max_batch_time==0
  ext4: clarify ext4_error message in ext4_mb_generate_buddy_error()
  ext4: clarify error count warning messages
  ext4: fix unjournalled bg descriptor while initializing inode bitmap

Pull clock driver fixes from Mike Turquette:
 "This batch of fixes is for a handful of clock drivers from Allwinner,
  Samsung, ST & TI.  Most of them are of the "this hardware won't work
  without this fix" variety, including patches that fix platforms that
  did not boot under certain configurations.  Other fixes are the result
  of changes to the clock core introduced in 3.15 that had subtle
  impacts on the clock drivers.

  There are no fixes to the clock framework core in this pull request"

* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mike.turquette/linux:
  clk: spear3xx: Set proper clock parent of uart1/2
  clk: spear3xx: Use proper control register offset
  clk: qcom: HDMI source sel is 3 not 2
  clk: sunxi: fix devm_ioremap_resource error detection code
  clk: s2mps11: Fix double free corruption during driver unbind
  clk: ti: am43x: Fix boot with CONFIG_SOC_AM33XX disabled
  clk: exynos5420: Remove aclk66_peric from the clock tree description
  clk/exynos5250: fix bit number for tv sysmmu clock
  clk: s3c64xx: Hookup SPI clocks correctly
  clk: samsung: exynos4: Remove SRC_MASK_ISP gates
  clk: samsung: add more aliases for s3c24xx
  clk: samsung: fix several typos to fix boot on s3c2410
  clk: ti: set CLK_SET_RATE_NO_REPARENT for ti,mux-clock
  clk: ti: am43x: Fix boot with CONFIG_SOC_AM33XX disabled
  clk: ti: dra7: return error code in failure case
  clk: ti: apll: not allocating enough data

Pull ARM SoC fixes from Olof Johansson:
 "This week's arm-soc fixes:

   - Another set of OMAP fixes
     * Clock fixes
     * Restart handling
     * PHY regulators
     * SATA hwmod data for DRA7
     + Some trivial fixes and removal of a bit of dead code
   - Exynos fixes
     * A bunch of clock fixes
     * Some SMP fixes
     * Exynos multi-core timer: register as clocksource and fix ftrace.
     + a few other minor fixes

  There's also a couple more patches, and at91 fix for USB caused by
  common clock conversion, and more MAINTAINERS entries for shmobile.

  We're definitely switching to only regression fixes from here on out,
  we've been a little less strict than usual up until now"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (26 commits)
  ARM: at91: at91sam9x5: add clocks for usb device
  ARM: EXYNOS: Register cpuidle device only on exynos4210 and 5250
  ARM: dts: Add clock property for mfc_pd in exynos5420
  clk: exynos5420: Add IDs for clocks used in PD mfc
  ARM: EXYNOS: Add support for clock handling in power domain
  ARM: OMAP2+: Remove non working OMAP HDMI audio initialization
  ARM: imx: fix shared gate clock
  ARM: dts: Update the parent for Audss clocks in Exynos5420
  ARM: EXYNOS: Update secondary boot addr for secure mode
  ARM: dts: Fix TI CPSW Phy mode selection on IGEP COM AQUILA.
  ARM: dts: am335x-evmsk: Enable the McASP FIFO for audio
  ARM: dts: am335x-evm: Enable the McASP FIFO for audio
  ARM: OMAP2+: Make GPMC skip disabled devices
  ARM: OMAP2+: create dsp device only on OMAP3 SoCs
  ARM: dts: dra7-evm: Make VDDA_1V8_PHY supply always on
  ARM: DRA7/AM43XX: fix header definition for omap44xx_restart
  ARM: OMAP2+: clock/dpll: fix _dpll_test_fint arithmetics overflow
  ARM: DRA7: hwmod: Add SYSCONFIG for usb_otg_ss
  ARM: DRA7: hwmod: Fixup SATA hwmod
  ARM: OMAP3: PRM/CM: Add back macros used by TI DSP/Bridge driver
  ...

Pull ARM fixes from Russell King:
 "Another round of fixes for ARM:
   - a set of kprobes fixes from Jon Medhurst
   - fix the revision checking for the L2 cache which wasn't noticed to
     have been broken"

* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
  ARM: l2c: fix revision checking
  ARM: kprobes: Fix test code compilation errors for ARMv4 targets
  ARM: kprobes: Disallow instructions with PC and register specified shift
  ARM: kprobes: Prevent known test failures stopping other tests running

Pull m68k fixes from Geert Uytterhoeven:
 "Summary:
  - Fix for a boot regression introduced in v3.16-rc1,
  - Fix for a build issue in -next"

Christoph Hellwig questioned why mach_random_get_entropy should be
exported to modules, and Geert explains that random_get_entropy() is
called by at least the crypto layer and ends up using it on m68k.  On
most other architectures it just uses get_cycles() (which is typically
inlined and doesn't need exporting),

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
  m68k: Export mach_random_get_entropy to modules
  m68k: Fix boot regression on machines with RAM at non-zero

Pull parisc fixes from Helge Deller:
 "The major patch in here is one which fixes the fanotify_mark() syscall
  in the compat layer of the 64bit parisc kernel.  It went unnoticed so
  long, because the calling syntax when using a 64bit parameter in a
  32bit syscall is quite complex and even worse, it may be even
  different if you call syscall() or the glibc wrapper.  This patch
  makes the kernel accept the calling convention when called by the
  glibc wrapper.

  The other two patches are trivial and remove unused headers, #includes
  and adds the serial ports of the fastest C8000 workstation to the
  parisc-kernel internal hardware database"

* 'parisc-3.16-5' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: drop unused defines and header includes
  parisc: fix fanotify_mark() syscall on 32bit compat kernel
  parisc: add serial ports of C8000/1GHz machine to hardware database

The uarts only work when the parent is ras_ahb_clk. The stale 3.5
based ST tree does this in the board file.

Add it to the clk init function. Not pretty, but the mess there is
amazing anyway.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>

The control register is at offset 0x10, not 0x0. This is wreckaged
since commit 5df33a62 (SPEAr: Switch to common clock framework).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>

Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # 3.13+

On parisc we can not use the existing compat implementation for fanotify_mark()
because for the 64bit mask parameter the higher and lower 32bits are ordered
differently than what the compat function expects from big endian
architectures.

Specifically:
It finally turned out, that on hppa we end up with different assignments
of parameters to kernel arguments depending on if we call the glibc
wrapper function
 int fanotify_mark (int __fanotify_fd, unsigned int __flags,
                    uint64_t __mask, int __dfd, const char *__pathname);
or directly calling the syscall manually
 syscall(__NR_fanotify_mark, ...)

Reason is, that the syscall() function is implemented as C-function and
because we now have the sysno as first parameter in front of the other
parameters the compiler will unexpectedly add an empty paramenter in
front of the u64 value to ensure the correct calling alignment for 64bit
values.
This means, on hppa you can't simply use syscall() to call the kernel
fanotify_mark() function directly, but you have to use the glibc
function instead.

This patch fixes the kernel in the hppa-arch specifc coding to adjust
the parameters in a way as if userspace calls the glibc wrapper function
fanotify_mark().
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # 3.13+

Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # 3.13+

Pull slave-dmaengine fixes from Vinod Koul:
 "We have two small fixes.  First one from Daniel to handle 0-length
  packets for usb cppi dma.  Second by Russell for imx-sdam cyclic
  residue reporting"

* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
  Update imx-sdma cyclic handling to report residue
  dma: cppi41: handle 0-length packets

Merge tag 'samsung-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes

Merge "Samsung fixes-3 for 3.16" from Kukjin Kim:

Samsung fixes-3 for v3.16
- update the parent for Auudss clock because kernel will be hang
  during late boot if the parent clock is disabled in bootloader.
- enable clk handing in power domain because while power domain
  on/off, its regarding clock source will be reset and it causes
  a problem so need to handle it.
- add mux clocks to be used by power domain for exynos5420-mfc
  during power domain on/off and property in device tree also.
- register cpuidle only for exynos4210 and exynos5250 because a
  system failure will be happened on other exynos SoCs.

* tag 'samsung-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
  ARM: EXYNOS: Register cpuidle device only on exynos4210 and 5250
  ARM: dts: Add clock property for mfc_pd in exynos5420
  clk: exynos5420: Add IDs for clocks used in PD mfc
  ARM: EXYNOS: Add support for clock handling in power domain
  ARM: dts: Update the parent for Audss clocks in Exynos5420
Signed-off-by: Olof Johansson <olof@lixom.net>

Pull USB fixes from Greg KH:
 "Here are some small USB fixes, PHY driver fixes (they ended up in this
  tree for lack of somewhere else to put them), and some new USB device
  ids"

* tag 'usb-3.16-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  phy: omap-usb2: Balance pm_runtime_enable() on probe failure and remove
  phy: core: Fix error path in phy_create()
  drivers: phy: phy-samsung-usb2.c: Add missing MODULE_DEVICE_TABLE
  phy: omap-usb2: fix devm_ioremap_resource error detection code
  phy: sun4i: depend on RESET_CONTROLLER
  USB: serial: ftdi_sio: Add Infineon Triboard
  USB: ftdi_sio: Add extra PID.
  usb: option: Add ID for Telewell TW-LTE 4G v2
  USB: cp210x: add support for Corsair usb dongle

Pull tty/serial fixes from Greg KH:
 "Here are some small serial fixes that resolve some reported problems
  that started in 3.15 with some serial drivers.

  And there's a new dt binding for a serial driver, which was all that
  was needed for the renesas serial driver"

* tag 'tty-3.16-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  serial: sh-sci: Add device tree support for r8a7{778,740,3a4} and sh73a0
  serial: imx: Fix build breakage
  serial: arc_uart: Use uart_circ_empty() for open-coded comparison
  serial: Test for no tx data on tx restart

Pull char/misc driver fixes from Greg KH:
 "Here are two hyperv driver fixes, and one i8k driver fix for 3.16"

* tag 'char-misc-3.16-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  i8k: Fix non-SMP operation
  Drivers: hv: util: Fix a bug in the KVP code
  Drivers: hv: vmbus: Fix a bug in the channel callback dispatch code

Pull IIO fixes from Greg KH:
 "Here are some IIO driver fixes for 3.16-rc5.  Nothing major, just
  resolves some minor issues that have been reported"

* tag 'staging-3.16-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  iio: ti_am335x_adc: Fix: Use same step id at FIFOs both ends
  iio:tcs3472: Check for buffer enabled and locking
  iio: hid-sensor-prox: Fix return values
  iio: hid-sensor-gyro-3d: Fix return values
  iio: hid-sensor-als: Fix return values
  iio: hid-sensor-magn-3d: Fix return values
  iio: hid-sensor-accel-3d: Fix return values
  iio: hid-sensor-press: Fix return values

Fix potential null pointer dereferencing problem caused by e43bb4e6
("ext4: decrement free clusters/inodes counters when block group declared bad")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Ashish Sangwan <a.sangwan@samsung.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Lukas Czerner <lczerner@redhat.com>

This fixes the following lockdep complaint:

[ INFO: possible circular locking dependency detected ]
3.16.0-rc2-mm1+ #7 Tainted: G           O  
-------------------------------------------------------
kworker/u24:0/4356 is trying to acquire lock:
 (&(&sbi->s_es_lru_lock)->rlock){+.+.-.}, at: [<ffffffff81285fff>] __ext4_es_shrink+0x4f/0x2e0

but task is already holding lock:
 (&ei->i_es_lock){++++-.}, at: [<ffffffff81286961>] ext4_es_insert_extent+0x71/0x180

which lock already depends on the new lock.

 Possible unsafe locking scenario:

       CPU0                    CPU1
       ----                    ----
  lock(&ei->i_es_lock);
                               lock(&(&sbi->s_es_lru_lock)->rlock);
                               lock(&ei->i_es_lock);
  lock(&(&sbi->s_es_lru_lock)->rlock);

 *** DEADLOCK ***

6 locks held by kworker/u24:0/4356:
 #0:  ("writeback"){.+.+.+}, at: [<ffffffff81071d00>] process_one_work+0x180/0x560
 #1:  ((&(&wb->dwork)->work)){+.+.+.}, at: [<ffffffff81071d00>] process_one_work+0x180/0x560
 #2:  (&type->s_umount_key#22){++++++}, at: [<ffffffff811a9c74>] grab_super_passive+0x44/0x90
 #3:  (jbd2_handle){+.+...}, at: [<ffffffff812979f9>] start_this_handle+0x189/0x5f0
 #4:  (&ei->i_data_sem){++++..}, at: [<ffffffff81247062>] ext4_map_blocks+0x132/0x550
 #5:  (&ei->i_es_lock){++++-.}, at: [<ffffffff81286961>] ext4_es_insert_extent+0x71/0x180

stack backtrace:
CPU: 0 PID: 4356 Comm: kworker/u24:0 Tainted: G           O   3.16.0-rc2-mm1+ #7
Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
Workqueue: writeback bdi_writeback_workfn (flush-253:0)
 ffffffff8213dce0 ffff880014b07538 ffffffff815df0bb 0000000000000007
 ffffffff8213e040 ffff880014b07588 ffffffff815db3dd ffff880014b07568
 ffff880014b07610 ffff88003b868930 ffff88003b868908 ffff88003b868930
Call Trace:
 [<ffffffff815df0bb>] dump_stack+0x4e/0x68
 [<ffffffff815db3dd>] print_circular_bug+0x1fb/0x20c
 [<ffffffff810a7a3e>] __lock_acquire+0x163e/0x1d00
 [<ffffffff815e89dc>] ? retint_restore_args+0xe/0xe
 [<ffffffff815ddc7b>] ? __slab_alloc+0x4a8/0x4ce
 [<ffffffff81285fff>] ? __ext4_es_shrink+0x4f/0x2e0
 [<ffffffff810a8707>] lock_acquire+0x87/0x120
 [<ffffffff81285fff>] ? __ext4_es_shrink+0x4f/0x2e0
 [<ffffffff8128592d>] ? ext4_es_free_extent+0x5d/0x70
 [<ffffffff815e6f09>] _raw_spin_lock+0x39/0x50
 [<ffffffff81285fff>] ? __ext4_es_shrink+0x4f/0x2e0
 [<ffffffff8119760b>] ? kmem_cache_alloc+0x18b/0x1a0
 [<ffffffff81285fff>] __ext4_es_shrink+0x4f/0x2e0
 [<ffffffff812869b8>] ext4_es_insert_extent+0xc8/0x180
 [<ffffffff812470f4>] ext4_map_blocks+0x1c4/0x550
 [<ffffffff8124c4c4>] ext4_writepages+0x6d4/0xd00
	...
Reported-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reported-by: Minchan Kim <minchan@kernel.org>
Cc: stable@vger.kernel.org
Cc: Zheng Liu <gnehzuil.liu@gmail.com>

Dell kernel driver dell-smo8800 provides same freefall interface as hp_accel so
program hpfall.c works also on Dell laptops. So rename it to freefall.c.

Dell driver does not provide hp::hddprotect led so make sure that freefall.c
works also if hp::hddprotect does not exist in sysfs.

Additionally write info to syslog.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Cc: Sonal Santan <sonal.santan@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This patch fixed spelling typo in various template files
within Documentation/Docbook.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This patch fixed spelling typo found in DocBook/mtdnand.tmpl.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Object-like macros are different than function-like macros:
https://gcc.gnu.org/onlinedocs/cpp/Object-like-Macros.html
https://gcc.gnu.org/onlinedocs/cpp/Function-like-Macros.html

They are not parsed correctly, generating invalid intermediate
files (xmls) for cases like:
    #define BIT_MASK    (0xFF << BIT_SHIFT)
where "OxFF <<" is considered to be parameter type.

When parsing, we can differentiate beween these two types of macros by
checking whether there is at least one whitespace b/w "#define" and
first opening parenthesis.
Signed-off-by: Horia Geanta <horia.geanta@freescale.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The paragraph on mcelog currently describes kernel v2.6.31. In that
kernel the mce code (for i386, that is) was in transition. Ever since
v2.6.32 the situation is much simpler (eg, mcelog is now needed to
process events on almost all x86 machines, i386 and x86-64). Since this
"document is designed to provide a list of the minimum levels of
software necessary to run the 3.0 kernels" let's just describe that
situation.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Add clocks for usb device, or else switch to CCF, the gadget
won't work.
Reported-by: Jiri Prchal <jiri.prchal@aksignal.cz>
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Tested-by: Jiri Prchal <jiri.prchal@aksignal.cz>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

If probe fails then we need to call pm_runtime_disable() to balance
out the previous pm_runtime_enable() call. Else it will cause
unbalanced pm_runtime_enable() call in the succeding probe call.

This anomaly was observed when the call to devm_phy_create() failed
with -EPROBE_DEFER.

Balance out the pm_runtime_enable() call in .remove() as well.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Prevent resources from being freed twice in case device_add() call
fails within phy_create(). Also use ida_simple_remove() instead of
ida_remove() as we had used ida_simple_get() to allocate the ida.

Cc: 3.13+ <stable@vger.kernel.org> # 3.13+
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Allow phy-exynos-usb2 to be autoloaded based on devicetree information.
Tested on Odroid X2 with its USB subsystem build as modules.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

devm_ioremap_resource returns an ERR_PTR value, not NULL, on failure.

A simplified version of the semantic match that finds this problem is as
follows:

// <smpl>
@@
expression e,e1;
statement S;
@@

*e = devm_ioremap_resource(...);
if (!e1) S

// </smpl>
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>