When switchdev_handle_fdb_event_to_device() replicates a FDB event
emitted for the bridge or for a LAG port and DSA offloads that, we
should notify back to switchdev that the FDB entry on the original
device is what was offloaded, not on the DSA slave devices that the
event is replicated on.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

By construction, the struct net_device *dev passed to
dsa_slave_switchdev_event_work() via struct dsa_switchdev_event_work
is always a DSA slave device.

Therefore, it is redundant to pass struct dsa_switch and int port
information in the deferred work structure. This can be retrieved at all
times from the provided struct net_device via dsa_slave_to_port().

For the same reason, we can drop the dsa_is_user_port() check in
dsa_fdb_offload_notify().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

When the switchdev_handle_fdb_event_to_device() event replication helper
was created, my original thought was that FDB events on LAG interfaces
should most likely be special-cased, not just replicated towards all
switchdev ports beneath that LAG. So this replication helper currently
does not recurse through switchdev lower interfaces of LAG bridge ports,
but rather calls the lag_mod_cb() if that was provided.

No switchdev driver uses this helper for FDB events on LAG interfaces
yet, so that was an assumption which was yet to be tested. It is
certainly usable for that purpose, as my RFC series shows:

https://patchwork.kernel.org/project/netdevbpf/cover/20220210125201.2859463-1-vladimir.oltean@nxp.com/

however this approach is slightly convoluted because:

- the switchdev driver gets a "dev" that isn't its own net device, but
  rather the LAG net device. It must call switchdev_lower_dev_find(dev)
  in order to get a handle of any of its own net devices (the ones that
  pass check_cb).

- in order for FDB entries on LAG ports to be correctly refcounted per
  the number of switchdev ports beneath that LAG, we haven't escaped the
  need to iterate through the LAG's lower interfaces. Except that is now
  the responsibility of the switchdev driver, because the replication
  helper just stopped half-way.

So, even though yes, FDB events on LAG bridge ports must be
special-cased, in the end it's simpler to let switchdev_handle_fdb_*
just iterate through the LAG port's switchdev lowers, and let the
switchdev driver figure out that those physical ports are under a LAG.

The switchdev_handle_fdb_event_to_device() helper takes a
"foreign_dev_check" callback so it can figure out whether @dev can
autonomously forward to @foreign_dev. DSA fills this method properly:
if the LAG is offloaded by another port in the same tree as @dev, then
it isn't foreign. If it is a software LAG, it is foreign - forwarding
happens in software.

Whether an interface is foreign or not decides whether the replication
helper will go through the LAG's switchdev lowers or not. Since the
lan966x doesn't properly fill this out, FDB events on software LAG
uppers will get called. By changing lan966x_foreign_dev_check(), we can
suppress them.

Whereas DSA will now start receiving FDB events for its offloaded LAG
uppers, so we need to return -EOPNOTSUPP, since we currently don't do
the right thing for them.

Cc: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The main purpose of this change is to create a data structure for a LAG
as seen by DSA. This is similar to what we have for bridging - we pass a
copy of this structure by value to ->port_lag_join and ->port_lag_leave.
For now we keep the lag_dev, id and a reference count in it. Future
patches will add a list of FDB entries for the LAG (these also need to
be refcounted to work properly).

The LAG structure is created using dsa_port_lag_create() and destroyed
using dsa_port_lag_destroy(), just like we have for bridging.

Because now, the dsa_lag itself is refcounted, we can simplify
dsa_lag_map() and dsa_lag_unmap(). These functions need to keep a LAG in
the dst->lags array only as long as at least one port uses it. The
refcounting logic inside those functions can be removed now - they are
called only when we should perform the operation.

dsa_lag_dev() is renamed to dsa_lag_by_id() and now returns the dsa_lag
structure instead of the lag_dev net_device.

dsa_lag_foreach_port() now takes the dsa_lag structure as argument.

dst->lags holds an array of dsa_lag structures.

dsa_lag_map() now also saves the dsa_lag->id value, so that linear
walking of dst->lags in drivers using dsa_lag_id() is no longer
necessary. They can just look at lag.id.

dsa_port_lag_id_get() is a helper, similar to dsa_port_bridge_num_get(),
which can be used by drivers to get the LAG ID assigned by DSA to a
given port.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Make the intent of the code more clear by using the dedicated helper for
iterating over the ports of a switch.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The DSA LAG API will be changed to become more similar with the bridge
data structures, where struct dsa_bridge holds an unsigned int num,
which is generated by DSA and is one-based. We have a similar thing
going with the DSA LAG, except that isn't stored anywhere, it is
calculated dynamically by dsa_lag_id() by iterating through dst->lags.

The idea of encoding an invalid (or not requested) LAG ID as zero for
the purpose of simplifying checks in drivers means that the LAG IDs
passed by DSA to drivers need to be one-based too. So back-and-forth
conversion is needed when indexing the dst->lags array, as well as in
drivers which assume a zero-based index.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In preparation of converting struct net_device *dp->lag_dev into a
struct dsa_lag *dp->lag, we need to rename, for consistency purposes,
all occurrences of the "lag" variable in qca8k to "lag_dev".
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In preparation of converting struct net_device *dp->lag_dev into a
struct dsa_lag *dp->lag, we need to rename, for consistency purposes,
all occurrences of the "lag" variable in mv88e6xxx to "lag_dev".
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In preparation of converting struct net_device *dp->lag_dev into a
struct dsa_lag *dp->lag, we need to rename, for consistency purposes,
all occurrences of the "lag" variable in the DSA core to "lag_dev".
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

This functions are mostly same except of one hard coded "in_pm" variable.
So, rework them to reduce maintenance overhead.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20220223110633.3006551-1-o.rempel@pengutronix.deSigned-off-by: Jakub Kicinski <kuba@kernel.org>

rhashtable_lookup_fast() returns NULL pointer not ERR_PTR(), so
it can return fib_node directly in prestera_kern_fib_cache_find().
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220223084954.1771075-2-yangyingliang@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

rhashtable_lookup_fast() returns NULL pointer not ERR_PTR(), so
it can return fib_node directly in prestera_fib_node_find().
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220223084954.1771075-1-yangyingliang@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Though the SparX-5i can control IPv4/6 multicasts separately from non-IP
multicasts, these are all muxed onto the bridge's BR_MCAST_FLOOD flag.
Signed-off-by: Casper Andersson <casper.casan@gmail.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/20220223082700.qrot7lepwqcdnyzw@wse-c0155Signed-off-by: Jakub Kicinski <kuba@kernel.org>

tools/testing/selftests/net/mptcp/mptcp_join.sh
  34aa6e3b ("selftests: mptcp: add ip mptcp wrappers")

  857898eb ("selftests: mptcp: add missing join check")
  6ef84b15 ("selftests: mptcp: more robust signal race test")
https://lore.kernel.org/all/20220221131842.468893-1-broonie@kernel.org/

drivers/net/ethernet/mellanox/mlx5/core/en/tc/act/act.h
drivers/net/ethernet/mellanox/mlx5/core/en/tc/act/ct.c
  fb7e76ea ("net/mlx5e: TC, Skip redundant ct clear actions")
  c63741b4 ("net/mlx5e: Fix MPLSoUDP encap to use MPLS action information")

  09bf9792 ("net/mlx5e: TC, Move pedit_headers_action to parse_attr")
  84ba8062 ("net/mlx5e: Test CT and SAMPLE on flow attr")
  efe6f961 ("net/mlx5e: CT, Don't set flow flag CT for ct clear flow")
  3b49a7ed ("net/mlx5e: TC, Reject rules with multiple CT actions")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Pull pci fixes from Bjorn Helgaas:

 - Fix a merge error that broke PCI device enumeration on mvebu
   platforms, including Turris Omnia (Armada 385) (Pali Rohár)

 - Avoid using ATS on all AMD Navi10 and Navi14 GPUs because some
   VBIOSes don't account for "harvested" (disabled) parts of the chip
   when initializing caches (Alex Deucher)

* tag 'pci-v5.17-fixes-5' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI: Mark all AMD Navi10 and Navi14 GPU ATS as broken
  PCI: mvebu: Fix device enumeration regression

Pull networking fixes from Jakub Kicinski:
 "Including fixes from bpf and netfilter.

  Current release - regressions:

   - bpf: fix crash due to out of bounds access into reg2btf_ids

   - mvpp2: always set port pcs ops, avoid null-deref

   - eth: marvell: fix driver load from initrd

   - eth: intel: revert "Fix reset bw limit when DCB enabled with 1 TC"

  Current release - new code bugs:

   - mptcp: fix race in overlapping signal events

  Previous releases - regressions:

   - xen-netback: revert hotplug-status changes causing devices to not
     be configured

   - dsa:
      - avoid call to __dev_set_promiscuity() while rtnl_mutex isn't
        held
      - fix panic when removing unoffloaded port from bridge

   - dsa: microchip: fix bridging with more than two member ports

  Previous releases - always broken:

   - bpf:
      - fix crash due to incorrect copy_map_value when both spin lock
        and timer are present in a single value
      - fix a bpf_timer initialization issue with clang
      - do not try bpf_msg_push_data with len 0
      - add schedule points in batch ops

   - nf_tables:
      - unregister flowtable hooks on netns exit
      - correct flow offload action array size
      - fix a couple of memory leaks

   - vsock: don't check owner in vhost_vsock_stop() while releasing

   - gso: do not skip outer ip header in case of ipip and net_failover

   - smc: use a mutex for locking "struct smc_pnettable"

   - openvswitch: fix setting ipv6 fields causing hw csum failure

   - mptcp: fix race in incoming ADD_ADDR option processing

   - sysfs: add check for netdevice being present to speed_show

   - sched: act_ct: fix flow table lookup after ct clear or switching
     zones

   - eth: intel: fixes for SR-IOV forwarding offloads

   - eth: broadcom: fixes for selftests and error recovery

   - eth: mellanox: flow steering and SR-IOV forwarding fixes

  Misc:

   - make __pskb_pull_tail() & pskb_carve_frag_list() drop_monitor
     friends not report freed skbs as drops

   - force inlining of checksum functions in net/checksum.h"

* tag 'net-5.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (85 commits)
  net: mv643xx_eth: process retval from of_get_mac_address
  ping: remove pr_err from ping_lookup
  Revert "i40e: Fix reset bw limit when DCB enabled with 1 TC"
  openvswitch: Fix setting ipv6 fields causing hw csum failure
  ipv6: prevent a possible race condition with lifetimes
  net/smc: Use a mutex for locking "struct smc_pnettable"
  bnx2x: fix driver load from initrd
  Revert "xen-netback: Check for hotplug-status existence before watching"
  Revert "xen-netback: remove 'hotplug-status' once it has served its purpose"
  net/mlx5e: Fix VF min/max rate parameters interchange mistake
  net/mlx5e: Add missing increment of count
  net/mlx5e: MPLSoUDP decap, fix check for unsupported matches
  net/mlx5e: Fix MPLSoUDP encap to use MPLS action information
  net/mlx5e: Add feature check for set fec counters
  net/mlx5e: TC, Skip redundant ct clear actions
  net/mlx5e: TC, Reject rules with forward and drop actions
  net/mlx5e: TC, Reject rules with drop and modify hdr action
  net/mlx5e: kTLS, Use CHECKSUM_UNNECESSARY for device-offloaded packets
  net/mlx5e: Fix wrong return value on ioctl EEPROM query failure
  net/mlx5: Fix possible deadlock on rule deletion
  ...

Nguyen, Anthony L says:

====================
10GbE Intel Wired LAN Driver Updates 2022-02-23

Yang Li fixes incorrect indenting as reported by smatch for ixgbevf.

Piotr removes non-inclusive language from ixgbe driver.

* '10GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
  ixgbe: Remove non-inclusive language
  ixgbevf: clean up some inconsistent indenting
====================

Link: https://lore.kernel.org/r/20220223185424.2129067-1-anthony.l.nguyen@intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Pull block fixes from Jens Axboe:

 - NVMe pull request:
    - send H2CData PDUs based on MAXH2CDATA (Varun Prakash)
    - fix passthrough to namespaces with unsupported features (Christoph
      Hellwig)

 - Clear iocb->private at poll completion (Stefano)

* tag 'block-5.17-2022-02-24' of git://git.kernel.dk/linux-block:
  nvme-tcp: send H2CData PDUs based on MAXH2CDATA
  nvme: also mark passthrough-only namespaces ready in nvme_update_ns_info
  nvme: don't return an error from nvme_configure_metadata
  block: clear iocb->private in blkdev_bio_end_io_async()

Pull io_uring fixes from Jens Axboe:

 - Add a conditional schedule point in io_add_buffers() (Eric)

 - Fix for a quiesce speedup merged in this release (Dylan)

 - Don't convert to jiffies for event timeout waiting, it's way too
   coarse when we accept a timespec as input (me)

* tag 'io_uring-5.17-2022-02-23' of git://git.kernel.dk/linux-block:
  io_uring: disallow modification of rsrc_data during quiesce
  io_uring: don't convert to jiffies for waiting on timeouts
  io_uring: add a schedule point in io_add_buffers()

Merge tag 'platform-drivers-x86-v5.17-4' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86

Pull more x86 platform driver fixes from Hans de Goede:
 "Two more fixes:

   - Fix suspend/resume regression on AMD Cezanne APUs in >= 5.16

   - Fix Microsoft Surface 3 battery readings"

* tag 'platform-drivers-x86-v5.17-4' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
  surface: surface3_power: Fix battery readings on batteries without a serial number
  platform/x86: amd-pmc: Set QOS during suspend on CZN w/ timer wakeup

Obtaining a MAC address may be deferred in cases when the MAC is stored
in an NVMEM block, for example, and it may not be ready upon the first
retrieval attempt and return EPROBE_DEFER.

It is also possible that a port that does not rely on NVMEM has been
already created when getting the defer request. Thus, also the resources
allocated previously must be freed when doing a roll-back.

Fixes: 76723bca ("net: mv643xx_eth: add DT parsing support")
Signed-off-by: Mauri Sandberg <maukka@ext.kapsi.fi>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220223142337.41757-1-maukka@ext.kapsi.fiSigned-off-by: Jakub Kicinski <kuba@kernel.org>

As Jakub noticed, prints should be avoided on the datapath.
Also, as packets would never come to the else branch in
ping_lookup(), remove pr_err() from ping_lookup().

Fixes: 35a79e64 ("ping: fix the dif and sdif check in ping_lookup")
Reported-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Link: https://lore.kernel.org/r/1ef3f2fcd31bd681a193b1fcf235eee1603819bd.1645674068.git.lucien.xin@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Revert of a patch that instead of fixing a AQ error when trying
to reset BW limit introduced several regressions related to
creation and managing TC. Currently there are errors when creating
a TC on both PF and VF.

Error log:
[17428.783095] i40e 0000:3b:00.1: AQ command Config VSI BW allocation per TC failed = 14
[17428.783107] i40e 0000:3b:00.1: Failed configuring TC map 0 for VSI 391
[17428.783254] i40e 0000:3b:00.1: AQ command Config VSI BW allocation per TC failed = 14
[17428.783259] i40e 0000:3b:00.1: Unable to  configure TC map 0 for VSI 391

This reverts commit 3d250466.

Fixes: 3d250466 (i40e: Fix reset bw limit when DCB enabled with 1 TC)
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20220223175347.1690692-1-anthony.l.nguyen@intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Ipv6 ttl, label and tos fields are modified without first
pulling/pushing the ipv6 header, which would have updated
the hw csum (if available). This might cause csum validation
when sending the packet to the stack, as can be seen in
the trace below.

Fix this by updating skb->csum if available.

Trace resulted by ipv6 ttl dec and then sending packet
to conntrack [actions: set(ipv6(hlimit=63)),ct(zone=99)]:
[295241.900063] s_pf0vf2: hw csum failure
[295241.923191] Call Trace:
[295241.925728]  <IRQ>
[295241.927836]  dump_stack+0x5c/0x80
[295241.931240]  __skb_checksum_complete+0xac/0xc0
[295241.935778]  nf_conntrack_tcp_packet+0x398/0xba0 [nf_conntrack]
[295241.953030]  nf_conntrack_in+0x498/0x5e0 [nf_conntrack]
[295241.958344]  __ovs_ct_lookup+0xac/0x860 [openvswitch]
[295241.968532]  ovs_ct_execute+0x4a7/0x7c0 [openvswitch]
[295241.979167]  do_execute_actions+0x54a/0xaa0 [openvswitch]
[295242.001482]  ovs_execute_actions+0x48/0x100 [openvswitch]
[295242.006966]  ovs_dp_process_packet+0x96/0x1d0 [openvswitch]
[295242.012626]  ovs_vport_receive+0x6c/0xc0 [openvswitch]
[295242.028763]  netdev_frame_hook+0xc0/0x180 [openvswitch]
[295242.034074]  __netif_receive_skb_core+0x2ca/0xcb0
[295242.047498]  netif_receive_skb_internal+0x3e/0xc0
[295242.052291]  napi_gro_receive+0xba/0xe0
[295242.056231]  mlx5e_handle_rx_cqe_mpwrq_rep+0x12b/0x250 [mlx5_core]
[295242.062513]  mlx5e_poll_rx_cq+0xa0f/0xa30 [mlx5_core]
[295242.067669]  mlx5e_napi_poll+0xe1/0x6b0 [mlx5_core]
[295242.077958]  net_rx_action+0x149/0x3b0
[295242.086762]  __do_softirq+0xd7/0x2d6
[295242.090427]  irq_exit+0xf7/0x100
[295242.093748]  do_IRQ+0x7f/0xd0
[295242.096806]  common_interrupt+0xf/0xf
[295242.100559]  </IRQ>
[295242.102750] RIP: 0033:0x7f9022e88cbd
[295242.125246] RSP: 002b:00007f9022282b20 EFLAGS: 00000246 ORIG_RAX: ffffffffffffffda
[295242.132900] RAX: 0000000000000005 RBX: 0000000000000010 RCX: 0000000000000000
[295242.140120] RDX: 00007f9022282ba8 RSI: 00007f9022282a30 RDI: 00007f9014005c30
[295242.147337] RBP: 00007f9014014d60 R08: 0000000000000020 R09: 00007f90254a8340
[295242.154557] R10: 00007f9022282a28 R11: 0000000000000246 R12: 0000000000000000
[295242.161775] R13: 00007f902308c000 R14: 000000000000002b R15: 00007f9022b71f40

Fixes: 3fdbd1ce ("openvswitch: add ipv6 'set' action")
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Link: https://lore.kernel.org/r/20220223163416.24096-1-paulb@nvidia.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

valid_lft, prefered_lft and tstamp are always accessed under the lock
"lock" in other places. Reading these without taking the lock may result
in inconsistencies regarding the calculation of the valid and preferred
variables since decisions are taken on these fields for those variables.
Signed-off-by: Niels Dossche <dossche.niels@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Niels Dossche <niels.dossche@ugent.be>
Link: https://lore.kernel.org/r/20220223131954.6570-1-niels.dossche@ugent.beSigned-off-by: Jakub Kicinski <kuba@kernel.org>

smc_pnetid_by_table_ib() uses read_lock() and then it calls smc_pnet_apply_ib()
which, in turn, calls mutex_lock(&smc_ib_devices.mutex).

read_lock() disables preemption. Therefore, the code acquires a mutex while in
atomic context and it leads to a SAC bug.

Fix this bug by replacing the rwlock with a mutex.

Reported-and-tested-by: syzbot+4f322a6d84e991c38775@syzkaller.appspotmail.com
Fixes: 64e28b52 ("net/smc: add pnet table namespace support")
Confirmed-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: Fabio M. De Francesco <fmdefrancesco@gmail.com>
Acked-by: Karsten Graul <kgraul@linux.ibm.com>
Link: https://lore.kernel.org/r/20220223100252.22562-1-fmdefrancesco@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Commit b7a49f73 ("bnx2x: Utilize firmware 7.13.21.0") added
new firmware support in the driver with maintaining older firmware
compatibility. However, older firmware was not added in MODULE_FIRMWARE()
which caused missing firmware files in initrd image leading to driver load
failure from initrd. This patch adds MODULE_FIRMWARE() for older firmware
version to have firmware files included in initrd.

Fixes: b7a49f73 ("bnx2x: Utilize firmware 7.13.21.0")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215627Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Alok Prasad <palok@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Link: https://lore.kernel.org/r/20220223085720.12021-1-manishc@marvell.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

This reverts commit 2afeec08.

The reasoning in the commit was wrong - the code expected to setup the
watch even if 'hotplug-status' didn't exist. In fact, it relied on the
watch being fired the first time - to check if maybe 'hotplug-status' is
already set to 'connected'. Not registering a watch for non-existing
path (which is the case if hotplug script hasn't been executed yet),
made the backend not waiting for the hotplug script to execute. This in
turns, made the netfront think the interface is fully operational, while
in fact it was not (the vif interface on xen-netback side might not be
configured yet).

This was a workaround for 'hotplug-status' erroneously being removed.
But since that is reverted now, the workaround is not necessary either.

More discussion at
https://lore.kernel.org/xen-devel/afedd7cb-a291-e773-8b0d-4db9b291fa98@ipxe.org/T/#uSigned-off-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Reviewed-by: Michael Brown <mbrown@fensystems.co.uk>
Link: https://lore.kernel.org/r/20220222001817.2264967-2-marmarek@invisiblethingslab.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

This reverts commit 1f256578.

The 'hotplug-status' node should not be removed as long as the vif
device remains configured. Otherwise the xen-netback would wait for
re-running the network script even if it was already called (in case of
the frontent re-connecting). But also, it _should_ be removed when the
vif device is destroyed (for example when unbinding the driver) -
otherwise hotplug script would not configure the device whenever it
re-appear.

Moving removal of the 'hotplug-status' node was a workaround for nothing
calling network script after xen-netback module is reloaded. But when
vif interface is re-created (on xen-netback unbind/bind for example),
the script should be called, regardless of who does that - currently
this case is not handled by the toolstack, and requires manual
script call. Keeping hotplug-status=connected to skip the call is wrong
and leads to not configured interface.

More discussion at
https://lore.kernel.org/xen-devel/afedd7cb-a291-e773-8b0d-4db9b291fa98@ipxe.org/T/#uSigned-off-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Link: https://lore.kernel.org/r/20220222001817.2264967-1-marmarek@invisiblethingslab.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Pull NVMe fixes from Christoph:

"nvme fixes for Linux 5.17

 - send H2CData PDUs based on MAXH2CDATA (Varun Prakash)
 - fix passthrough to namespaces with unsupported features (me)"

* tag 'nvme-5.17-2022-02-24' of git://git.infradead.org/nvme:
  nvme-tcp: send H2CData PDUs based on MAXH2CDATA
  nvme: also mark passthrough-only namespaces ready in nvme_update_ns_info
  nvme: don't return an error from nvme_configure_metadata

The battery on the 2nd hand Surface 3 which I recently bought appears to
not have a serial number programmed in. This results in any I2C reads from
the registers containing the serial number failing with an I2C NACK.

This was causing mshw0011_bix() to fail causing the battery readings to
not work at all.

Ignore EREMOTEIO (I2C NACK) errors when retrieving the serial number and
continue with an empty serial number to fix this.

Fixes: b1f81b49 ("platform/x86: surface3_power: MSHW0011 rev-eng implementation")
BugLink: https://github.com/linux-surface/linux-surface/issues/608Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220224101848.7219-1-hdegoede@redhat.com

commit 59348401 ("platform/x86: amd-pmc: Add special handling for
timer based S0i3 wakeup") adds support for using another platform timer
in lieu of the RTC which doesn't work properly on some systems. This path
was validated and worked well before submission. During the 5.16-rc1 merge
window other patches were merged that caused this to stop working properly.

When this feature was used with 5.16-rc1 or later some OEM laptops with the
matching firmware requirements from that commit would shutdown instead of
program a timer based wakeup.

This was bisected to commit 8d89835b ("PM: suspend: Do not pause
cpuidle in the suspend-to-idle path").  This wasn't supposed to cause any
negative impacts and also tested well on both Intel and ARM platforms.
However this changed the semantics of when CPUs are allowed to be in the
deepest state. For the AMD systems in question it appears this causes a
firmware crash for timer based wakeup.

It's hypothesized to be caused by the `amd-pmc` driver sending `OS_HINT`
and all the CPUs going into a deep state while the timer is still being
programmed. It's likely a firmware bug, but to avoid it don't allow setting
CPUs into the deepest state while using CZN timer wakeup path.

If later it's discovered that this also occurs from "regular" suspends
without a timer as well or on other silicon, this may be later expanded to
run in the suspend path for more scenarios.

Cc: stable@vger.kernel.org # 5.16+
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/linux-acpi/BL1PR12MB51570F5BD05980A0DCA1F3F4E23A9@BL1PR12MB5157.namprd12.prod.outlook.com/T/#mee35f39c41a04b624700ab2621c795367f19c90e
Fixes: 8d89835b ("PM: suspend: Do not pause cpuidle in the suspend-to-idle path")
Fixes: 23f62d7a ("PM: sleep: Pause cpuidle later and resume it earlier during system transitions")
Fixes: 59348401 ("platform/x86: amd-pmc: Add special handling for timer based S0i3 wakeup"
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20220223175237.6209-1-mario.limonciello@amd.comReviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

Merge tag 'linux-can-next-for-5.18-20220224' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next

Marc Kleine-Budde says:

====================
this is a pull request of 36 patches for net-next/master.

The first 5 patches are by me and update various CAN DT bindings.

Eric Dumazet's patch for the CAN GW replaces a costly
synchronize_rcu() by a call_rcu().

The next 2 patches by me enhance the CAN bit rate handling, the bit
rate checking is simplified and the arguments and local variables of
functions are marked as const.

A patch by me for the kvaser_usb driver removes a redundant variable.

The next patch by me lets the c_can driver use the default ethtool
drvinfo.

Minghao Chi's patch for the softing driver removes a redundant
variable.

Srinivas Neeli contributes an enhancement for the xilinx_can NAPI poll
function.

Vincent Mailhol's patch for the etas_es58x driver converts to
BITS_PER_TYPE() from of manual calculation.

The next 23 patches target the mcp251xfd driver and are by me. The
first 15 patches, add support for the internal PLL, which includes
simplifying runtime PM handling, better chip detection and error
handling after wakeup, and the PLL handling. The last 8 patches
prepare the driver to support multiple RX-FIFOs and runtime
configurable RX/TX rings. The actual runtime ring configuration via
ethtool will be added in a later patch series.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch introduces macros to define the number of supported TEF, RX
and TX rings. As well as some assertions as sanity checks.

Link: https://lore.kernel.org/all/20220217103826.2299157-9-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch prepares the driver to use more than one RX-FIFO. Having a
bigger RX buffer is beneficial in high load situations, where the
system temporarily cannot keep up reading CAN frames from the chip.
Using a bigger RX buffer also allows to implement RX IRQ coalescing,
which will be added in a later patch series.

If using more than 1 RX-FIFO the driver has to figure out, which FIFOs
have RX'ed CAN frames pending. This is indicated by a set bit in the
RXIF register, which is positioned directly after the interrupt status
register INT. If more than 1 RX-FIFO is used, the driver reads both
registers in 1 transfer.

The mcp251xfd_handle_rxif() function iterates over all RX rings and
reads out the RX'ed CAN frames for for all pending FIFOs. To keep the
logic for the 1 RX-FIFO only case in mcp251xfd_handle_rxif() simple,
the driver marks that FIFO pending in mcp251xfd_ring_init().

The chip has a dedicated RX interrupt line to signal pending RX'ed
frames. If connected to an input GPIO and the driver will skip the
initial read of the interrupt status register (INT) and directly read
the pending RX'ed frames if the line is active. The driver assumes the
1st RX-FIFO pending (a read of the RXIF register would re-introduce
the skipped initial read of the INT register). Any other pending
RX-FIFO will be served in the main interrupt handler.

Link: https://lore.kernel.org/all/20220217103826.2299157-8-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

The recent change of the order of the TX and RX FIFOs is not reflected
in the debug info of the FIFO setup. This patch adjust the order and
additionally prints the base address of each FIFO.

Since the mcp251xfd_ring_init() may fail due to wrongly configured
FIFOs, printing of the FIFO setup is moved there. In case of an error
it would not be printed in mcp251xfd_ring_init().

Link: https://lore.kernel.org/all/20220217103826.2299157-7-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

With this patch the usage of the on-chip RAM is checked. In the
current driver the FIFO setup is fixed and always fits into the RAM.

With an upcoming patch series the ring and FIFO setup will be more
dynamic. Although using more RAM than available should not happen, but
add this safety check, just in case.

Link: https://lore.kernel.org/all/20220217103826.2299157-6-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch actually changes the order of the TX and RX FIFOs.

This gives the opportunity to minimize the number of SPI transfers in
the IRQ handler. The read of the IRQ status register and RX FIFO
status registers can be combined into single SPI transfer. If the RX
ring uses FIFO 1, the overall length of the transfer is smaller than
in the original layout, where the RX FIFO comes after the TX FIFO.

Link: https://lore.kernel.org/all/20220217103826.2299157-5-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch improves the initialization of the TX and RX rings. The
initialization functions are now called with pointers to the next free
address (in the on chip RAM) and next free hardware FIFO. The rings
are initialized using these values and the pointers are modified to
point to the next free elements.

This means the order of the mcp251xfd_ring_init_*() functions
specifies the order of the rings in the hardware FIFO. This makes it
possible to change the order of the TX and RX FIFOs, which is done in
the next patch.

This gives the opportunity to minimize the number of SPI transfers in
the IRQ handler. The read of the IRQ status register and RX FIFO
status registers can be combined into single SPI transfer. If the RX
ring uses FIFO 1, the overall length of the transfer is smaller than
in the original layout, where the RX FIFO comes after the TX FIFO.

Link: https://lore.kernel.org/all/20220217103826.2299157-4-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch splits the initialization of the TEF, TX and RX FIFO in the
mcp251xfd_ring_init() function into separate functions. This is a
preparation patch to move the RX FIFO in front of the TX FIFO.

Link: https://lore.kernel.org/all/20220217103826.2299157-3-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>