Prevents direct charging control in cable notification and only set the
input current limit according to cable type.  Leave the enabling of
charing to cm_monitor() where charging management proceeds.  We may lose
a few ms to enable charging compared to before, but it's more important
that charging is enabled always in safe context.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

cm_monitor(), where charging management starts, checks various charging
condition sequentially to decide next charging operation. However, as it
follows sequential process, cascaded if statements, it does some
jobs which have already done in the previous stage. This results in a
delay in decision making. Moreover, starting point of charging is spread
all around which makes maintain code and debugging difficult.

Both of the problems mentioned above become clean if it manages battery
charging focusing on battery status not following sequential condition
checking.  Now, cm_monitor() moves battery state diagram and does the
optimal operation for current state. As a result, it reduces whole
monitoring time almost in half.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Current charger-manager calls power_supply_changed() whenever charging
status is changed. Remove the separated power_supply_changed() calls
and let it be called at end of try_charger_enable() function which
is called to set charging/discharging.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

The POWER_SUPPLY_CHARGE_NOW/FULL property reflects battery's charges
in uAh unit, but charger-manager has been used it wrongly as a
status field.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

We were using POWER_SUPPLY_PROP_TEMP if the temperature was coming
via the fuel gauge and POWER_SUPPLY_PROP_TEMP_AMBIENT if it was
coming via the thermal framework.  Since they're mutually
exclusive in the driver and we don't know if the thermal framework
 is ambient or not, unify them both to use POWER_SUPPLY_PROP_TEMP.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

cm_notify_event() was introduced to get an event associated with the
battery status externally (ie in board files), but no one ever used it.
Moreover it makes charger manager driver more complicated. Drop the
function and all data related to it to simplify the driver.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Whenever the battery status is changed, charger manager triggers a uevent
through a private interface. Modify it to use power_supply_changed()
since it belongs to the power supply subsystem.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Both chips have charger and a fuel gauge.

This adds basic support for displaying the state of the battery and the
input power, settings are not modified. There are some defaults set via
OTP.

Charging also starts after plugging USB.

Known issues of the fuel gauge: There are drivers in the wild which disable
the fuel gauge at shutdown. If a kernel is booted without fuel gauge
support, after such a driver has been used, the fuel gauge will stay off
and decalibrate.
If this driver is used after that, it might display wrong values for charge
level.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Current sbs-battery considers all smbus errors as disconnection events
when battery-detect pin isn't supplied, and restored to present state back
when any successful transaction is made.

This can lead to unwanted state changes between present and !present
when there's one i2c error and other following commands were successful.

This patch provides a unified way of checking presence by calling
sbs_get_battery_presence_and_health() when detect pin is not used.
Signed-off-by: Ikjoon Jang <ikjn@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Simplify the driver and remove the DT specific code by
using the generic device property framework.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

There are no platforms using the pdata support, so let's
drop it to simplify the driver.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Update the license to the SPDX licensing format.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

There is a spelling mistake in a dev_dbg message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

This patch enables calling sbs_get_battery_presence_and_health()
without checking its chip type. No functional changes.
Signed-off-by: Ikjoon Jang <ikjn@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Remove unused enable_detection flag which is always true after
the device is proved.
Signed-off-by: Ikjoon Jang <ikjn@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Add new charge-current-limit feature to gpio-charger.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Immutable branch between arm and power-supply for gpio-charger for 5.10

This immutable branch drops legacy gpio API from
gpio-charger and updates the remaining users to
the new gpiod API instead.
Signed-off-by: Sebastian Reichel <sre@kernel.org>

This converts the GPIO charger to use exclusively GPIO
descriptors, moving the two remaining platforms passing
global GPIO numbers over to using a GPIO descriptor table.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Common pattern of handling deferred probe can be simplified with
dev_err_probe().  Less code and also it prints the error value.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Common pattern of handling deferred probe can be simplified with
dev_err_probe().  Less code and also it prints the error value.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Common pattern of handling deferred probe can be simplified with
dev_err_probe().  Less code and also it prints the error value.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Common pattern of handling deferred probe can be simplified with
dev_err_probe().  Less code and also it prints the error value.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Common pattern of handling deferred probe can be simplified with
dev_err_probe().  Less code and also it prints the error value.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Currently, power_supply framework supports only Battery, UPS,
Mains and USB power_supply_type. Add wireless power_supply_type
so that the drivers which supports wireless can register a power
supply class device with POWER_SUPPLY_TYPE_WIRELESS.
Signed-off-by: Subbaraman Narayanamurthy <subbaram@codeaurora.org>
Signed-off-by: Guru Das Srinagesh <gurus@codeaurora.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Let's simply disable/enable IRQ rather than use a mutex that protects from
racing with the interrupt handler. The result of this patch is that it's a
bit easier now to follow the driver's code.
Tested-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

SMB347 is a charger and not a battery driver. Secondly, power-supply core
now supports monitored-battery. So the 'fake' battery doesn't do anything
useful for us, and thus, it should be removed.

Transfer smb347-battery functionality into smb347-mains and smb347-usb.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

SMB345 tested on Nexus 7 2013.

Based on:
- https://patchwork.kernel.org/patch/4922431/
- https://patchwork.ozlabs.org/patch/666877/Signed-off-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

This patch adds device-tree support to the SMB347 charger driver. All
legacy platform data now can be parsed from DT. Because of that and since
SMB347 is an I2C client driver, the IRQ number can be passed automatically
through client's IRQ variable if it's defined in DT. There is no need to
map GPIO to IRQ manually in the case of DT.

This patch is based on the original work made by:
Jonghwa Lee <jonghwa3.lee@samsung.com>
Link: https://patchwork.kernel.org/patch/4284731/Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

The generic battery temperature properties are already supported by the
power-supply core. Let's support parsing of the common battery temperature
properties from a device-tree.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Summit SMB3xx series is a Programmable Switching Li+ Battery Charger.
This patch adds device-tree binding for Summit SMB345, SMB347 and SMB358
chargers.
Signed-off-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Document generic battery temperature properties.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Simplify code, more convenient to use with Device Tree.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Convert reboot-mode bindings to YAML.
Signed-off-by: Elliot Berman <eberman@codeaurora.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Constify a number of static variables that are not modified to allow the
compiler to put them in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

This battery appears only to be used by a single board (DA850), so it
makes sense to add this to the Kconfig file so that users don't build
the module unnecessarily. It currently seems to be built for the x86
Arch Linux kernel where it's probably not doing much good.
Signed-off-by: Alex Dewar <alex.dewar90@gmail.com>
Acked-by: David Lechner <david@lechnology.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Pull io_uring fixes from Jens Axboe:
 "A few differerent things in here.

  Seems like syzbot got some more io_uring bits wired up, and we got a
  handful of reports and the associated fixes are in here.

  General fixes too, and a lot of them marked for stable.

  Lastly, a bit of fallout from the async buffered reads, where we now
  more easily trigger short reads. Some applications don't really like
  that, so the io_read() code now handles short reads internally, and
  got a cleanup along the way so that it's now easier to read (and
  documented). We're now passing tests that failed before"

* tag 'io_uring-5.9-2020-08-15' of git://git.kernel.dk/linux-block:
  io_uring: short circuit -EAGAIN for blocking read attempt
  io_uring: sanitize double poll handling
  io_uring: internally retry short reads
  io_uring: retain iov_iter state over io_read/io_write calls
  task_work: only grab task signal lock when needed
  io_uring: enable lookup of links holding inflight files
  io_uring: fail poll arm on queue proc failure
  io_uring: hold 'ctx' reference around task_work queue + execute
  fs: RWF_NOWAIT should imply IOCB_NOIO
  io_uring: defer file table grabbing request cleanup for locked requests
  io_uring: add missing REQ_F_COMP_LOCKED for nested requests
  io_uring: fix recursive completion locking on oveflow flush
  io_uring: use TWA_SIGNAL for task_work uncondtionally
  io_uring: account locked memory before potential error case
  io_uring: set ctx sq/cq entry count earlier
  io_uring: Fix NULL pointer dereference in loop_rw_iter()
  io_uring: add comments on how the async buffered read retry works
  io_uring: io_async_buf_func() need not test page bit

Commit 1355c31e ("asm-generic: pgalloc: provide generic pmd_alloc_one()
and pmd_free_one()") converted parisc to use generic version of
pmd_alloc_one() but it missed the fact that parisc uses order-1 pages for
PMD.

Restore the original version of pmd_alloc_one() for parisc, just use
GFP_PGTABLE_KERNEL that implies __GFP_ZERO instead of GFP_KERNEL and
memset.

Fixes: 1355c31e ("asm-generic: pgalloc: provide generic pmd_alloc_one() and pmd_free_one()")
Reported-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Tested-by: Meelis Roos <mroos@linux.ee>
Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Link: https://lkml.kernel.org/r/9f2b5ebd-e4a4-0fa1-6cd3-4b9f6892d1ad@linux.eeSigned-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull block fixes from Jens Axboe:
 "A few fixes on the block side of things:

   - Discard granularity fix (Coly)

   - rnbd cleanups (Guoqing)

   - md error handling fix (Dan)

   - md sysfs fix (Junxiao)

   - Fix flush request accounting, which caused an IO slowdown for some
     configurations (Ming)

   - Properly propagate loop flag for partition scanning (Lennart)"

* tag 'block-5.9-2020-08-14' of git://git.kernel.dk/linux-block:
  block: fix double account of flush request's driver tag
  loop: unset GENHD_FL_NO_PART_SCAN on LOOP_CONFIGURE
  rnbd: no need to set bi_end_io in rnbd_bio_map_kern
  rnbd: remove rnbd_dev_submit_io
  md-cluster: Fix potential error pointer dereference in resize_bitmaps()
  block: check queue's limits.discard_granularity in __blkdev_issue_discard()
  md: get sysfs entry after redundancy attr group create

Pull RISC-V fix from Palmer Dabbelt:
 "I collected a single fix during the merge window: we managed to break
  the early trap setup on !MMU, this fixes it"

* tag 'riscv-for-linus-5.9-mw1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
  riscv: Setup exception vector for nommu platform