Using an element of a struct as the address for the memcpy of the whole
struct may introduce a buffer overflow and does not help readability either
simply pass the real thing as first argument to memcpy.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Since Roland stepped down, the community asked me to take his place, and
the nomination was followed by sufficient votes and no dissensions that
we can move forward with the change.
Signed-off-by: Doug Ledford <dledford@redhat.com>

Most headers for InfiniBand/RDMA are located under
include/rdma/ and include/uapi/rdma.
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

See also patch "IPoIB/cm: Add connected mode support for devices
without SRQs" (commit ID 68e995a2). Detected by smatch.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Pradeep Satyanarayana <pradeeps@linux.vnet.ibm.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Remove these log messages in favor of per-endpoint counters as well as
device-global counters that can be inspected via debugfs.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Addresses the following kernel logs seen during boot of sparc systems:

Kernel unaligned access at TPC[103bce50] cm_find_listen+0x34/0xf8 [ib_cm]
Kernel unaligned access at TPC[103bce50] cm_find_listen+0x34/0xf8 [ib_cm]
Kernel unaligned access at TPC[103bce50] cm_find_listen+0x34/0xf8 [ib_cm]
Kernel unaligned access at TPC[103bce50] cm_find_listen+0x34/0xf8 [ib_cm]
Kernel unaligned access at TPC[103bce50] cm_find_listen+0x34/0xf8 [ib_cm]
Signed-off-by: David Ahern <david.ahern@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Signed-off-by: Honggang Li <honli@redhat.com>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

This driver already makes use of ioremap_wc() on PIO buffers,
so convert it to use arch_phys_wc_add().

The qib driver uses a mmap() special case for when PAT is
not used, this behaviour used to be determined with a
module parameter but since we have been asked to just
remove that module parameter this checks for the WC cookie,
if not set we can assume PAT was used. If its set we do
what we used to do for the mmap for when MTRR was enabled.

The removal of the module parameter is OK given that Andy
notes that even if users of module parameter are still around
it will not prevent loading of the module on recent kernels.

Cc: Doug Ledford <dledford@redhat.com>
Cc: Toshi Kani <toshi.kani@hp.com>
Cc: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Cc: Mike Marciniszyn <mike.marciniszyn@intel.com>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: Dennis Dalessandro <dennis.dalessandro@intel.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Suresh Siddha <sbsiddha@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Juergen Gross <jgross@suse.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Antonino Daplas <adaplas@gmail.com>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Stefan Bader <stefan.bader@canonical.com>
Cc: konrad.wilk@oracle.com
Cc: ville.syrjala@linux.intel.com
Cc: david.vrabel@citrix.com
Cc: jbeulich@suse.com
Cc: Roger Pau Monné <roger.pau@citrix.com>
Cc: infinipath@intel.com
Cc: linux-rdma@vger.kernel.org
Cc: linux-fbdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: xen-devel@lists.xensource.com
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

There is no good reason not to, we eventually delete it as well.

Cc: Toshi Kani <toshi.kani@hp.com>
Cc: Suresh Siddha <sbsiddha@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Juergen Gross <jgross@suse.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Antonino Daplas <adaplas@gmail.com>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Mike Marciniszyn <infinipath@intel.com>
Cc: Roland Dreier <roland@kernel.org>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: linux-rdma@vger.kernel.org
Cc: linux-fbdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

While unmapping an ODP writable page, the dirty bit of the page is set. In
order to do so, the head of the compound page is found.
Currently, the compound head is found even on non-writable pages, where it is
never used, leading to unnecessary cpu barrier that impacts performance.

This patch moves the search for the compound head to be done only when needed.
Signed-off-by: Guy Shapiro <guysh@mellanox.com>
Acked-by: Shachar Raindel <raindel@mellanox.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Currently, while mapping or unmapping pages for ODP, the umem mutex is locked
and unlocked once for each page. Such lock/unlock operation take few tens to
hundreds of nsecs. This makes a significant impact when mapping or unmapping few
MBs of memory.

To avoid this, the mutex should be locked only once per operation, and not per
page.
Signed-off-by: Guy Shapiro <guysh@mellanox.com>
Acked-by: Shachar Raindel <raindel@mellanox.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Get the actual (non-mapped) ip/tcp address of the connecting peer from
the port mapper

Also setup the passive side endpoint to correctly display the actual
and mapped addresses for the new connection.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Get the actual (non-mapped) ip/tcp address of the connecting peer from
the port mapper and report the address info to the user space application
at the time of connection establishment
Signed-off-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

RDMA/core: Enable the iWarp Port Mapper to provide the actual address of the connecting peer to its clients

Add functionality to enable the port mapper on the passive side to provide to its
clients the actual (non-mapped) ip/tcp address information of the connecting peer

1) Adding remote_info_cb() to process the address info of the connecting peer
   The address info is provided by the user space port mapper service when
   the connection is initiated by the peer
2) Adding a hash list to store the remote address info
3) Adding functionality to add/remove the remote address info
   After the info has been provided to the port mapper client,
   it is removed from the hash list
Signed-off-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Currently the iw_cxgb4 implementation requires the qp and cq qid densities
to match as well as the qp and cq id ranges.  So fail a device open if
the device configuration doesn't meet the requirements.

The reason for these restictions has to do with the fact that IQ qid X
has a UGTS register in the same bar2 page as EQ qid X.  Thus both qids
need to be allocated to the same user process for security reasons.
The logic that does this (the qpid allocator in iw_cxgb4/resource.c)
handles this but requires the above restrictions.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

For T5, we must not use the kdb/kgts registers, in order avoid db drops
under extreme loads.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

- get_dma_mr() was using ~0UL which is should be ~0ULL.  This causes the
DMA MR to get setup incorrectly in hardware.

- wr_log_show() needed a 64b divide function div64_u64() instead of
  doing
division directly.

- fixed warnings about recasting a pointer to a u64
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Cleanup macros and register defines for consistency
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

When accepting a new IPv4 connect to an IPv6 socket, the CMA tries to
canonize the address family to IPv4, but does not properly process
the listening sockaddr to get the listening port, and does not properly
set the address family of the canonized sockaddr.

Fixes: e51060f0 ("IB: IP address based RDMA connection manager")

Cc: <stable@vger.kernel.org>
Reported-By: Yotam Kenneth <yotamke@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Pull ext4 fixes from Ted Ts'o:
 "Some miscellaneous bug fixes and some final on-disk and ABI changes
  for ext4 encryption which provide better security and performance"

* tag 'for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: fix growing of tiny filesystems
  ext4: move check under lock scope to close a race.
  ext4: fix data corruption caused by unwritten and delayed extents
  ext4 crypto: remove duplicated encryption mode definitions
  ext4 crypto: do not select from EXT4_FS_ENCRYPTION
  ext4 crypto: add padding to filenames before encrypting
  ext4 crypto: simplify and speed up filename encryption

Pull drm fixes from Dave Airlie:
 "One intel fix, one rockchip fix, and a bunch of radeon fixes for some
  regressions from audio rework and vm stability"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/i915/chv: Implement WaDisableShadowRegForCpd
  drm/radeon: fix userptr return value checking (v2)
  drm/radeon: check new address before removing old one
  drm/radeon: reset BOs address after clearing it.
  drm/radeon: fix lockup when BOs aren't part of the VM on release
  drm/radeon: add SI DPM quirk for Sapphire R9 270 Dual-X 2G GDDR5
  drm/radeon: adjust pll when audio is not enabled
  drm/radeon: only enable audio streams if the monitor supports it
  drm/radeon: only mark audio as connected if the monitor supports it (v3)
  drm/radeon/audio: don't enable packets until the end
  drm/radeon: drop dce6_dp_enable
  drm/radeon: fix ordering of AVI packet setup
  drm/radeon: Use drm_calloc_ab for CS relocs
  drm/rockchip: fix error check when getting irq
  MAINTAINERS: add entry for Rockchip drm drivers

Just a single intel fix
* tag 'drm-intel-fixes-2015-04-30' of git://anongit.freedesktop.org/drm-intel:
  drm/i915/chv: Implement WaDisableShadowRegForCpd

one fix and maintainers update
* 'drm-next0420' of https://github.com/markyzq/kernel-drm-rockchip:
  drm/rockchip: fix error check when getting irq
  MAINTAINERS: add entry for Rockchip drm drivers

Pull SCSI fixes from James Bottomley:
 "This is three logical fixes (as 5 patches).

  The 3ware class of drivers were causing an oops with multiqueue by
  tearing down the command mappings after completing the command (where
  the variables in the command used to tear down the mapping were
  no-longer valid).  There's also a fix for the qnap iscsi target which
  was choking on us sending it commands that were too long and a fix for
  the reworked aha1542 allocating GFP_KERNEL under a lock"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  3w-9xxx: fix command completion race
  3w-xxxx: fix command completion race
  3w-sas: fix command completion race
  aha1542: Allocate memory before taking a lock
  SCSI: add 1024 max sectors black list flag

Pull slave dmaengine fixes from Vinod Koul:
 "Here are the fixes in dmaengine subsystem for rc2:

   - privatecnt fix for slave dma request API by Christopher

   - warn fix for PM ifdef in usb-dmac by Geert

   - fix hardware dependency for xgene by Jean"

* 'next' of git://git.infradead.org/users/vkoul/slave-dma:
  dmaengine: increment privatecnt when using dma_get_any_slave_channel
  dmaengine: xgene: Set hardware dependency
  dmaengine: usb-dmac: Protect PM-only functions to kill warning

Pull powerpc fixes from Michael Ellerman:
 - build fix for SMP=n in book3s_xics.c
 - fix for Daniel's pci_controller_ops on powernv.
 - revert the TM syscall abort patch for now.
 - CPU affinity fix from Nathan.
 - two EEH fixes from Gavin.
 - fix for CR corruption from Sam.
 - selftest build fix.

* tag 'powerpc-4.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux:
  powerpc/powernv: Restore non-volatile CRs after nap
  powerpc/eeh: Delay probing EEH device during hotplug
  powerpc/eeh: Fix race condition in pcibios_set_pcie_reset_state()
  powerpc/pseries: Correct cpu affinity for dlpar added cpus
  selftests/powerpc: Fix the pmu install rule
  Revert "powerpc/tm: Abort syscalls in active transactions"
  powerpc/powernv: Fix early pci_controller_ops loading.
  powerpc/kvm: Fix SMP=n build error in book3s_xics.c

The estimate of necessary transaction credits in ext4_flex_group_add()
is too pessimistic. It reserves credit for sb, resize inode, and resize
inode dindirect block for each group added in a flex group although they
are always the same block and thus it is enough to account them only
once. Also the number of modified GDT block is overestimated since we
fit EXT4_DESC_PER_BLOCK(sb) descriptors in one block.

Make the estimation more precise. That reduces number of requested
credits enough that we can grow 20 MB filesystem (which has 1 MB
journal, 79 reserved GDT blocks, and flex group size 16 by default).
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>

fallocate() checks that the file is extent-based and returns
EOPNOTSUPP in case is not. Other tasks can convert from and to
indirect and extent so it's safe to check only after grabbing
the inode mutex.
Signed-off-by: Davide Italiano <dccitaliano@gmail.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org

Currently it is possible to lose whole file system block worth of data
when we hit the specific interaction with unwritten and delayed extents
in status extent tree.

The problem is that when we insert delayed extent into extent status
tree the only way to get rid of it is when we write out delayed buffer.
However there is a limitation in the extent status tree implementation
so that when inserting unwritten extent should there be even a single
delayed block the whole unwritten extent would be marked as delayed.

At this point, there is no way to get rid of the delayed extents,
because there are no delayed buffers to write out. So when a we write
into said unwritten extent we will convert it to written, but it still
remains delayed.

When we try to write into that block later ext4_da_map_blocks() will set
the buffer new and delayed and map it to invalid block which causes
the rest of the block to be zeroed loosing already written data.

For now we can fix this by simply not allowing to set delayed status on
written extent in the extent status tree. Also add WARN_ON() to make
sure that we notice if this happens in the future.

This problem can be easily reproduced by running the following xfs_io.

xfs_io -f -c "pwrite -S 0xaa 4096 2048" \
          -c "falloc 0 131072" \
          -c "pwrite -S 0xbb 65536 2048" \
          -c "fsync" /mnt/test/fff

echo 3 > /proc/sys/vm/drop_caches
xfs_io -c "pwrite -S 0xdd 67584 2048" /mnt/test/fff

This can be theoretically also reproduced by at random by running fsx,
but it's not very reliable, though on machines with bigger page size
(like ppc) this can be seen more often (especially xfstest generic/127)
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org

This patch removes duplicated encryption modes which were already in
ext4.h. They were duplicated from commit 3edc18d8 and commit f542fb.

Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Michael Halcrow <mhalcrow@google.com>
Cc: Andreas Dilger <adilger.kernel@dilger.ca>
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>

This patch adds a tristate EXT4_ENCRYPTION to do the selections
for EXT4_FS_ENCRYPTION because selecting from a bool causes all
the selected options to be built-in, even if EXT4 itself is a
module.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>

Pull networking fixes from David Miller:

 1) Receive packet length needs to be adjust by 2 on RX to accomodate
    the two padding bytes in altera_tse driver.  From Vlastimil Setka.

 2) If rx frame is dropped due to out of memory in macb driver, we leave
    the receive ring descriptors in an undefined state.  From Punnaiah
    Choudary Kalluri

 3) Some netlink subsystems erroneously signal NLM_F_MULTI.  That is
    only for dumps.  Fix from Nicolas Dichtel.

 4) Fix mis-use of raw rt->rt_pmtu value in ipv4, one must always go via
    the ipv4_mtu() helper.  From Herbert Xu.

 5) Fix null deref in bridge netfilter, and miscalculated lengths in
    jump/goto nf_tables verdicts.  From Florian Westphal.

 6) Unhash ping sockets properly.

 7) Software implementation of BPF divide did 64/32 rather than 64/64
    bit divide.  The JITs got it right.  Fix from Alexei Starovoitov.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (30 commits)
  ipv4: Missing sk_nulls_node_init() in ping_unhash().
  net: fec: Fix RGMII-ID mode
  net/mlx4_en: Schedule napi when RX buffers allocation fails
  netxen_nic: use spin_[un]lock_bh around tx_clean_lock
  net/mlx4_core: Fix unaligned accesses
  mlx4_en: Use correct loop cursor in error path.
  cxgb4: Fix MC1 memory offset calculation
  bnx2x: Delay during kdump load
  net: Fix Kernel Panic in bonding driver debugfs file: rlb_hash_table
  net: dsa: Fix scope of eeprom-length property
  net: macb: Fix race condition in driver when Rx frame is dropped
  hv_netvsc: Fix a bug in netvsc_start_xmit()
  altera_tse: Correct rx packet length
  mlx4: Fix tx ring affinity_mask creation
  tipc: fix problem with parallel link synchronization mechanism
  tipc: remove wrong use of NLM_F_MULTI
  bridge/nl: remove wrong use of NLM_F_MULTI
  bridge/mdb: remove wrong use of NLM_F_MULTI
  net: sched: act_connmark: don't zap skb->nfct
  trivial: net: systemport: bcmsysport.h: fix 0x0x prefix
  ...

Here the "other side" refers to the guest or host.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

With my job change kernel work will be "own time"; I'm keeping lguest
and modules (and the virtio standards work), but virtio kernel has to
go.

This makes it clear that Michael is in charge.  He's good, but having
me watch over his shoulder won't help.

Good luck Michael!
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull Ceph RBD fix from Sage Weil.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
  rbd: end I/O the entire obj_request on error

If we don't do that, then the poison value is left in the ->pprev
backlink.

This can cause crashes if we do a disconnect, followed by a connect().
Tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: Wen Xu <hotdog3645@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When we end I/O struct request with error, we need to pass
obj_request->length as @nr_bytes so that the entire obj_request worth
of bytes is completed.  Otherwise block layer ends up confused and we
trip on

    rbd_assert(more ^ (which == img_request->obj_request_count));

in rbd_img_obj_callback() due to more being true no matter what.  We
already do it in most cases but we are missing some, in particular
those where we don't even get a chance to submit any obj_requests, due
to an early -ENOMEM for example.

A number of obj_request->xferred assignments seem to be redundant but
I haven't touched any of obj_request->xferred stuff to keep this small
and isolated.

Cc: Alex Elder <elder@linaro.org>
Cc: stable@vger.kernel.org # 3.10+
Reported-by: Shawn Edwards <lesser.evil@gmail.com>
Reviewed-by: Sage Weil <sage@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>

This obscures the length of the filenames, to decrease the amount of
information leakage.  By default, we pad the filenames to the next 4
byte boundaries.  This costs nothing, since the directory entries are
aligned to 4 byte boundaries anyway.  Filenames can also be padded to
8, 16, or 32 bytes, which will consume more directory space.

Change-Id: Ibb7a0fb76d2c48e2061240a709358ff40b14f322
Signed-off-by: Theodore Ts'o <tytso@mit.edu>

Avoid using SHA-1 when calculating the user-visible filename when the
encryption key is available, and avoid decrypting lots of filenames
when searching for a directory entry in a directory block.

Change-Id: If4655f144784978ba0305b597bfa1c8d7bb69e63
Signed-off-by: Theodore Ts'o <tytso@mit.edu>