- 22 Jun, 2021 32 commits
-
-
Johannes Berg authored
In gen3, after firmware is alive, we no longer need the firmware and image loader images, only the context info itself and PRPH info/scratch need to remain. Call iwl_pcie_ctxt_info_gen3_free() appropriately in the alive callback (iwl_trans_pcie_gen2_fw_alive()) with a new argument indicating whether it can free everything or only partially. The context info and PRPH scratch are also not needed after PNVM load, but we don't have a good hook for freeing after that, so keep them for now. Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20210618105614.8230d91a46c1.Ia7db71e5e6265ca87363f1481eac1bc3bbebb15c@changeidSigned-off-by:
-
Johannes Berg authored
We don't fill in phy_data.d1 in no-data RX, and thus we pretend some data is actually filled in radiotap when it isn't or has default (zero) values. Fill in phy_data.d1 appropriately, and while at it also move the info_type initialization into the initializer. Signed-off-by:
-
Johannes Berg authored
After firmware alive, iwl_trans_pcie_gen2_fw_alive() is called to free the context info. However, on gen3 that will then free the context info with the wrong size. Since we free this allocation later, let it stick around until the device is stopped for now, freeing some of it earlier is a separate change. Signed-off-by:
-
Johannes Berg authored
In the case of gen3 devices with image loader (IML) support, we were leaking the IML DMA allocation and never freeing it. Fix that. Signed-off-by:
-
Emmanuel Grumbach authored
It's been a while that the firmware uses LONG_GROUP by default and not LEGACY_GROUP. Until now the firmware wrongly advertise the WOWLAN_GET_STATUS command's version with LEGACY_GROUP, but it is now being fixed. In order to support both firmwares, first try to get the version number of the command with the LONG_GROUP and if the firmware didn't advertise the command version with LONG_GROUP, try to get the command version with LEGACY_GROUP. Signed-off-by:
Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by:
-
Naftali Goldstein authored
These two version updates deprecate the need to set/get the nonqos sequence counter during suspend/resume flow respectively; NICs supporting this version maintain this counter internally and don't lose it during the suspend/resume flow. Note that this means that for such NICs the NON_QOS_TX_COUNTER_CMD is no longer ever sent. Signed-off-by:
Naftali Goldstein <naftali.goldstein@intel.com> Signed-off-by:
-
Naftali Goldstein authored
When operating in AP mode with NICs supporting the AP_LINK_PS hw flag, mac80211 doesn't need to start/stop queueing tx for connected stations because the FW already handles that. Signed-off-by:
-
Ilan Peer authored
In case of unbinding, the FW would remove the session protection time events without sending a notification, so explicitly cancel the session protection, so future requests for mgd_prepare_tx() would not assume that the session protection is running. Signed-off-by:
Ilan Peer <ilan.peer@intel.com> Signed-off-by:
-
Abhishek Naik authored
Read the UNII4 setting from the ACPI table and use it in the LARI_CONFIG_CHANGE_CMD accordingly. This setting allows OEMs to enable or disable UNII4, bypassing the FW defaults. Signed-off-by:
Abhishek Naik <abhishek.naik@intel.com> Signed-off-by:
-
Johannes Berg authored
The TR/CR tail data are meant to be per-queue-arrays, however, we allocate them completely wrong (we have a separate allocation per queue). Looking at this more closely, it turns out that the hardware never uses these - we have a separate free list per RX queue and maintain a write pointer for that in a register, and the RX itself is indicated in the RB status (rb_stts) DMA region. Despite nothing using the tail pointers, the hardware will unconditionally access them to write updates, even when we aren't using CRs/TRs. Give it dummy values that we never use/update so it can do that without causing trouble. Signed-off-by:
-
Johannes Berg authored
"ubd" is really called "used_bd", fix that. Signed-off-by:
-
Shaul Triebitz authored
If the firmware supports broadcast TWT (know by TLV), add the broadcast TWT HE MAC capability. Signed-off-by:
Shaul Triebitz <shaul.triebitz@intel.com> Signed-off-by:
-
Avraham Stern authored
If the LMR feedback is set in the ranging request, set the corresponding flag in the fw command. Signed-off-by:
Avraham Stern <avraham.stern@intel.com> Signed-off-by:
-
Johannes Berg authored
The (default) HE capabilities for our devices weren't handled correctly, adjust them to match the correct capabilities of the devices. Since the device regulatory will not allow 160 MHz on 5 GHz, don't advertise this capability by default; do it only if an NVM file is being loaded that might change the regulatory parameters. Signed-off-by:
-
Harish Mitty authored
For IWL_DEVICE_FAMILY_22000 & greater, driver will call NMI instead of REPLY_ERROR as FW->Infra does not support this command for this family onwards. Signed-off-by:
Harish Mitty <harish.mitty@intel.com> Signed-off-by:
-
Shaul Triebitz authored
When the session protection ends and the Driver is not associated or a beacon was not heard, the Driver prints "No beacons heard...". That's confusing for the case where not associated. Change the print when not associated to "Not associated...". Signed-off-by:
-
Johannes Berg authored
The firmware can now request SMPS (due to thermal conditions), add some code to honour such requests and bubble them up through the stack, subject to our other SMPS constraints, e.g. from Bluetooth. Then, if the firmware requests SMPS, then we know that it supports a small extension to the PHY configuration API where a chain mask of 0 means "use 1 but pick which one yourself", so in this case we use that extension. During firmware restart, we stay in the previous state, and the FW will send us a notification at startup (only) if the temperature is below the lower or above the high threshold, to sync the state. Signed-off-by:
-
Johannes Berg authored
SMPS requests may differ per interfaces due to e.g. Bluetooth only interfering on 2.4 GHz, so if that's the case we should, in the case of multiple PHY contexts, still allow RX diversity on PHY context that have no interfaces with SMPS requests. Fix the code to pass through the PHY context in question and skip interfaces with non-matching PHY context while iterating. Signed-off-by:
-
Johannes Berg authored
This is not valid (in the spec) and mac80211 will soon warn on it, in addition to ignoring it. Signed-off-by:
-
Johannes Berg authored
Identify and print out the RF module to be able to identify (from logs and through debugfs) which one (and version) is present on the system. Signed-off-by:
-
Mukesh Sisodiya authored
Region TLV version 2 now includes more data, but it is not relevant for the driver. In order to support this new version, just mask the new part out. Signed-off-by:
Mukesh Sisodiya <mukesh.sisodiya@intel.com> Signed-off-by:
-
Johannes Berg authored
This configuration struct is declared twice, remove one of the declarations. Signed-off-by:
-
Johannes Berg authored
This is duplicated with CSR_HW_RFID_TYPE so just use the latter for less typing/shorter lines. Signed-off-by:
-
Johannes Berg authored
Printing the interrupt index in our local array isn't very useful in an error message, print the interrupt number (as also shown in e.g. /proc/interrupts) instead. Signed-off-by:
-
Matti Gottlieb authored
Add support for AX231 radio modules, which we call Fm. These modules can be used with the Ma family of devices and above. Signed-off-by:
Matti Gottlieb <matti.gottlieb@intel.com> Signed-off-by:
-
Luca Coelho authored
The FW has a watchdog of 200ms in the PNVM load flow, so the driver should have a slightly higher timeout. Change the timeout from 100ms to 250ms. Signed-off-by:
-
Johannes Berg authored
pcim_iomap_table() might return NULL, so we shouldn't unconditionally dereference the return value by taking the [0] entry. Handle this better by checking for NULL first, and then separately checking if the [0] entry is NULL. Signed-off-by:
-
Johannes Berg authored
When we have a P2P Device active, we attempt to only change the PHY context it uses when we get a new remain-on-channel, if the P2P Device is the only user of the PHY context. This is fine if we're switching within a band, but if we're switching bands then the switch implies a removal and re-add of the PHY context, which isn't permitted by the firmware while it's bound to an interface. Fix the code to skip the unbind/release/... cycle only if the band doesn't change (or we have old devices that can switch the band on the fly as well.) Signed-off-by:
-
Luca Coelho authored
We don't use this command anymore and it is going to be removed from the FW. Remove all related definitions. Signed-off-by:
-
Luca Coelho authored
Two functions had indentation mistakes which were causing sparse warnings. Fix them. Signed-off-by:
-
Luca Coelho authored
Allow the caller to pass the clock type to iwl_mvm_get_sync_time() so callers with different needs can decide whether to use boottime or realtime. Signed-off-by:
-
Miri Korenblit authored
Read the new BIOS DSM and Pass to FW if to disable\enable 11ax for Russia according to the BIOS key. This is needed to enable OEMs to control enable/disable 11ax in Russia. Also add support for future "enable 11ax in country X" features. Signed-off-by:
Miri Korenblit <miriam.rachel.korenblit@intel.com> Signed-off-by:
-
- 19 Jun, 2021 8 commits
-
-
Íñigo Huguet authored
One USB data buffer can contain multiple received network packets. If that's the case, they're processed this way: 1. Original buffer is cloned 2. Original buffer is trimmed to contain only the first network packet 3. This first network packet is passed to network stack 4. Cloned buffer is trimmed to eliminate the first network packet 5. Repeat with the cloned buffer until there are no more network packets inside However, if the space remaining in original buffer after the first network packet is not enough to contain at least another network packet descriptor, it is not cloned. The loop parsing this packets ended if remaining space == 0. But if the remaining space was > 0 but < packet descriptor size, another iteration of the loop was done, processing again the previous packet because cloning didn't happen. Moreover, the ownership of this packet had been passed to network stack in the previous iteration. This patch ensures that no extra iteration is done if the remaining size is not enough for one packet, and also avoid the first iteration for the same reason. Probably this doesn't happen in practice, but can happen theoretically. Signed-off-by:
Íñigo Huguet <ihuguet@redhat.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210511071926.8951-1-ihuguet@redhat.com
-
Pascal Terjan authored
Based on 2001:3319 and 2357:0109 which I used to test the fix and 0bda:818b and 2357:0108 for which I found efuse dumps online. == 2357:0109 == === Before === Vendor: Realtek Product: \x03802.11n NI Serial: === After === Vendor: Realtek Product: 802.11n NIC Serial not available. == 2001:3319 == === Before === Vendor: Realtek Product: Wireless N Serial: no USB Adap === After === Vendor: Realtek Product: Wireless N Nano USB Adapter Serial not available. Signed-off-by:
Pascal Terjan <pterjan@google.com> Signed-off-by:
-
https://github.com/nbd168/wirelessKalle Valo authored
mt76 patches for 5.14 * mt7915 MSI support * disable ASPM on mt7915 * mt7915 tx status reporting * mt7921 decap offload * driver fixes * cleanups * mt7921 runtime power management improvements * testmode improvements/fixes * runtime PM improvements
-
Lorenzo Bianconi authored
Disable chip full reset just during device probing but allow it during hw restart. Signed-off-by:
Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by:
Felix Fietkau <nbd@nbd.name>
-
Lorenzo Bianconi authored
Set macwork timeout value according to runtime-pm in order to reduce power consumption Signed-off-by:
-
Lorenzo Bianconi authored
Allow the user to enable runtime-pm for mt7663s driver Signed-off-by:
-
Lorenzo Bianconi authored
Similar to mt7663e, rely on mt76_connac_pm_ref/mt76_connac_pm_unref to check PM state and increment/decrement wake counter Signed-off-by:
-
Lorenzo Bianconi authored
As already done for mt7921 and mt7663e, rely on pm reference counting in drv/fw_own Signed-off-by:
-
