commit 103a07d4 upstream.

meson_sar_adc_clear_fifo passes a 0 as value-pointer to regmap_read().
In case of the meson-saradc driver this ends up in regmap_mmio_read(),
where the value-pointer is de-referenced unconditionally to assign the
value which was read.
Fix this by passing an actual pointer, even though all we want to do is
to discard the value.

As a side-effect this fixes a sparse warning ("Using plain integer as
NULL pointer") as reported by Paolo Cretaro.

Fixes: 3adbf342 ("iio: adc: add a driver for the SAR ADC found in Amlogic Meson SoCs")
Reported-by: Paolo Cretaro <paolocretaro@gmail.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 95264c8c upstream.

ad7152_write_raw_samp_freq() is called by ad7152_write_raw() with
chip->state_lock held. So, there is unavoidable deadlock when
ad7152_write_raw_samp_freq() locks the mutex itself.

The patch removes unneeded locking.

Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Fixes: 6572389b ("staging: iio: cdc: ad7152: Implement IIO_CHAN_INFO_SAMP_FREQ attribute")
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 948588e2 upstream.

Starting from MPU6500, accelerometer dlpf is set in a separate
register named ACCEL_CONFIG_2.
Add this new register in the map and set it for the corresponding
chips.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 64c2b203 upstream.

Anon and hugetlbfs handle FOLL_DUMP set by get_dump_page() internally to
__get_user_pages().

shmem as opposed has no special FOLL_DUMP handling there so
handle_mm_fault() is invoked without mmap_sem and ends up calling
handle_userfault() that isn't expecting to be invoked without mmap_sem
held.

This makes handle_userfault() fail immediately if invoked through
shmem_vm_ops->fault during coredumping and solves the problem.

The side effect is a BUG_ON with no lock held triggered by the
coredumping process which exits.  Only 4.11 is affected, pre-4.11 anon
memory holes are skipped in __get_user_pages by checking FOLL_DUMP
explicitly against empty pagetables (mm/gup.c:no_page_table()).

It's zero cost as we already had a check for current->flags to prevent
futex to trigger userfaults during exit (PF_EXITING).

Link: http://lkml.kernel.org/r/20170615214838.27429-1-aarcange@redhat.comSigned-off-by: Andrea Arcangeli <aarcange@redhat.com>
Reported-by: "Dr. David Alan Gilbert" <dgilbert@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 3c226c63 upstream.

In do_huge_pmd_numa_page(), we attempt to handle a migrating thp pmd by
waiting until the pmd is unlocked before we return and retry.  However,
we can race with migrate_misplaced_transhuge_page():

    // do_huge_pmd_numa_page                // migrate_misplaced_transhuge_page()
    // Holds 0 refs on page                 // Holds 2 refs on page

    vmf->ptl = pmd_lock(vma->vm_mm, vmf->pmd);
    /* ... */
    if (pmd_trans_migrating(*vmf->pmd)) {
            page = pmd_page(*vmf->pmd);
            spin_unlock(vmf->ptl);
                                            ptl = pmd_lock(mm, pmd);
                                            if (page_count(page) != 2)) {
                                                    /* roll back */
                                            }
                                            /* ... */
                                            mlock_migrate_page(new_page, page);
                                            /* ... */
                                            spin_unlock(ptl);
                                            put_page(page);
                                            put_page(page); // page freed here
            wait_on_page_locked(page);
            goto out;
    }

This can result in the freed page having its waiters flag set
unexpectedly, which trips the PAGE_FLAGS_CHECK_AT_PREP checks in the
page alloc/free functions.  This has been observed on arm64 KVM guests.

We can avoid this by having do_huge_pmd_numa_page() take a reference on
the page before dropping the pmd lock, mirroring what we do in
__migration_entry_wait().

When we hit the race, migrate_misplaced_transhuge_page() will see the
reference and abort the migration, as it may do today in other cases.

Fixes: b8916634 ("mm: Prevent parallel splits during THP migration")
Link: http://lkml.kernel.org/r/1497349722-6731-2-git-send-email-will.deacon@arm.comSigned-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Acked-by: Steve Capper <steve.capper@arm.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Mel Gorman <mgorman@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit ef707629 upstream.

I saw need_resched() warnings when swapping on large swapfile (TBs)
because continuously allocating many pages in swap_cgroup_prepare() took
too long.

We already cond_resched when freeing page in swap_cgroup_swapoff().  Do
the same for the page allocation.

Link: http://lkml.kernel.org/r/20170604200109.17606-1-yuzhao@google.comSigned-off-by: Yu Zhao <yuzhao@google.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Vladimir Davydov <vdavydov.dev@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 7258ae5c upstream.

memory_failure() chooses a recovery action function based on the page
flags.  For huge pages it uses the tail page flags which don't have
anything interesting set, resulting in:

> Memory failure: 0x9be3b4: Unknown page state
> Memory failure: 0x9be3b4: recovery action for unknown page: Failed

Instead, save a copy of the head page's flags if this is a huge page,
this means if there are no relevant flags for this tail page, we use the
head pages flags instead.  This results in the me_huge_page() recovery
action being called:

> Memory failure: 0x9b7969: recovery action for huge page: Delayed

For hugepages that have not yet been allocated, this allows the hugepage
to be dequeued.

Fixes: 524fca1e ("HWPOISON: fix misjudgement of page_action() for errors on mlocked pages")
Link: http://lkml.kernel.org/r/20170524130204.21845-1-james.morse@arm.comSigned-off-by: James Morse <james.morse@arm.com>
Tested-by: Punit Agrawal <punit.agrawal@arm.com>
Acked-by: Punit Agrawal <punit.agrawal@arm.com>
Acked-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit f16443a0 upstream.

Using the syzkaller kernel fuzzer, Andrey Konovalov generated the
following error in gadgetfs:

> BUG: KASAN: use-after-free in __lock_acquire+0x3069/0x3690
> kernel/locking/lockdep.c:3246
> Read of size 8 at addr ffff88003a2bdaf8 by task kworker/3:1/903
>
> CPU: 3 PID: 903 Comm: kworker/3:1 Not tainted 4.12.0-rc4+ #35
> Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
> Workqueue: usb_hub_wq hub_event
> Call Trace:
>  __dump_stack lib/dump_stack.c:16 [inline]
>  dump_stack+0x292/0x395 lib/dump_stack.c:52
>  print_address_description+0x78/0x280 mm/kasan/report.c:252
>  kasan_report_error mm/kasan/report.c:351 [inline]
>  kasan_report+0x230/0x340 mm/kasan/report.c:408
>  __asan_report_load8_noabort+0x19/0x20 mm/kasan/report.c:429
>  __lock_acquire+0x3069/0x3690 kernel/locking/lockdep.c:3246
>  lock_acquire+0x22d/0x560 kernel/locking/lockdep.c:3855
>  __raw_spin_lock include/linux/spinlock_api_smp.h:142 [inline]
>  _raw_spin_lock+0x2f/0x40 kernel/locking/spinlock.c:151
>  spin_lock include/linux/spinlock.h:299 [inline]
>  gadgetfs_suspend+0x89/0x130 drivers/usb/gadget/legacy/inode.c:1682
>  set_link_state+0x88e/0xae0 drivers/usb/gadget/udc/dummy_hcd.c:455
>  dummy_hub_control+0xd7e/0x1fb0 drivers/usb/gadget/udc/dummy_hcd.c:2074
>  rh_call_control drivers/usb/core/hcd.c:689 [inline]
>  rh_urb_enqueue drivers/usb/core/hcd.c:846 [inline]
>  usb_hcd_submit_urb+0x92f/0x20b0 drivers/usb/core/hcd.c:1650
>  usb_submit_urb+0x8b2/0x12c0 drivers/usb/core/urb.c:542
>  usb_start_wait_urb+0x148/0x5b0 drivers/usb/core/message.c:56
>  usb_internal_control_msg drivers/usb/core/message.c:100 [inline]
>  usb_control_msg+0x341/0x4d0 drivers/usb/core/message.c:151
>  usb_clear_port_feature+0x74/0xa0 drivers/usb/core/hub.c:412
>  hub_port_disable+0x123/0x510 drivers/usb/core/hub.c:4177
>  hub_port_init+0x1ed/0x2940 drivers/usb/core/hub.c:4648
>  hub_port_connect drivers/usb/core/hub.c:4826 [inline]
>  hub_port_connect_change drivers/usb/core/hub.c:4999 [inline]
>  port_event drivers/usb/core/hub.c:5105 [inline]
>  hub_event+0x1ae1/0x3d40 drivers/usb/core/hub.c:5185
>  process_one_work+0xc08/0x1bd0 kernel/workqueue.c:2097
>  process_scheduled_works kernel/workqueue.c:2157 [inline]
>  worker_thread+0xb2b/0x1860 kernel/workqueue.c:2233
>  kthread+0x363/0x440 kernel/kthread.c:231
>  ret_from_fork+0x2a/0x40 arch/x86/entry/entry_64.S:424
>
> Allocated by task 9958:
>  save_stack_trace+0x1b/0x20 arch/x86/kernel/stacktrace.c:59
>  save_stack+0x43/0xd0 mm/kasan/kasan.c:513
>  set_track mm/kasan/kasan.c:525 [inline]
>  kasan_kmalloc+0xad/0xe0 mm/kasan/kasan.c:617
>  kmem_cache_alloc_trace+0x87/0x280 mm/slub.c:2745
>  kmalloc include/linux/slab.h:492 [inline]
>  kzalloc include/linux/slab.h:665 [inline]
>  dev_new drivers/usb/gadget/legacy/inode.c:170 [inline]
>  gadgetfs_fill_super+0x24f/0x540 drivers/usb/gadget/legacy/inode.c:1993
>  mount_single+0xf6/0x160 fs/super.c:1192
>  gadgetfs_mount+0x31/0x40 drivers/usb/gadget/legacy/inode.c:2019
>  mount_fs+0x9c/0x2d0 fs/super.c:1223
>  vfs_kern_mount.part.25+0xcb/0x490 fs/namespace.c:976
>  vfs_kern_mount fs/namespace.c:2509 [inline]
>  do_new_mount fs/namespace.c:2512 [inline]
>  do_mount+0x41b/0x2d90 fs/namespace.c:2834
>  SYSC_mount fs/namespace.c:3050 [inline]
>  SyS_mount+0xb0/0x120 fs/namespace.c:3027
>  entry_SYSCALL_64_fastpath+0x1f/0xbe
>
> Freed by task 9960:
>  save_stack_trace+0x1b/0x20 arch/x86/kernel/stacktrace.c:59
>  save_stack+0x43/0xd0 mm/kasan/kasan.c:513
>  set_track mm/kasan/kasan.c:525 [inline]
>  kasan_slab_free+0x72/0xc0 mm/kasan/kasan.c:590
>  slab_free_hook mm/slub.c:1357 [inline]
>  slab_free_freelist_hook mm/slub.c:1379 [inline]
>  slab_free mm/slub.c:2961 [inline]
>  kfree+0xed/0x2b0 mm/slub.c:3882
>  put_dev+0x124/0x160 drivers/usb/gadget/legacy/inode.c:163
>  gadgetfs_kill_sb+0x33/0x60 drivers/usb/gadget/legacy/inode.c:2027
>  deactivate_locked_super+0x8d/0xd0 fs/super.c:309
>  deactivate_super+0x21e/0x310 fs/super.c:340
>  cleanup_mnt+0xb7/0x150 fs/namespace.c:1112
>  __cleanup_mnt+0x1b/0x20 fs/namespace.c:1119
>  task_work_run+0x1a0/0x280 kernel/task_work.c:116
>  exit_task_work include/linux/task_work.h:21 [inline]
>  do_exit+0x18a8/0x2820 kernel/exit.c:878
>  do_group_exit+0x14e/0x420 kernel/exit.c:982
>  get_signal+0x784/0x1780 kernel/signal.c:2318
>  do_signal+0xd7/0x2130 arch/x86/kernel/signal.c:808
>  exit_to_usermode_loop+0x1ac/0x240 arch/x86/entry/common.c:157
>  prepare_exit_to_usermode arch/x86/entry/common.c:194 [inline]
>  syscall_return_slowpath+0x3ba/0x410 arch/x86/entry/common.c:263
>  entry_SYSCALL_64_fastpath+0xbc/0xbe
>
> The buggy address belongs to the object at ffff88003a2bdae0
>  which belongs to the cache kmalloc-1024 of size 1024
> The buggy address is located 24 bytes inside of
>  1024-byte region [ffff88003a2bdae0, ffff88003a2bdee0)
> The buggy address belongs to the page:
> page:ffffea0000e8ae00 count:1 mapcount:0 mapping:          (null)
> index:0x0 compound_mapcount: 0
> flags: 0x100000000008100(slab|head)
> raw: 0100000000008100 0000000000000000 0000000000000000 0000000100170017
> raw: ffffea0000ed3020 ffffea0000f5f820 ffff88003e80efc0 0000000000000000
> page dumped because: kasan: bad access detected
>
> Memory state around the buggy address:
>  ffff88003a2bd980: fb fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
>  ffff88003a2bda00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
> >ffff88003a2bda80: fc fc fc fc fc fc fc fc fc fc fc fc fb fb fb fb
>                                                                 ^
>  ffff88003a2bdb00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
>  ffff88003a2bdb80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
> ==================================================================

What this means is that the gadgetfs_suspend() routine was trying to
access dev->lock after it had been deallocated.  The root cause is a
race in the dummy_hcd driver; the dummy_udc_stop() routine can race
with the rest of the driver because it contains no locking.  And even
when proper locking is added, it can still race with the
set_link_state() function because that function incorrectly drops the
private spinlock before invoking any gadget driver callbacks.

The result of this race, as seen above, is that set_link_state() can
invoke a callback in gadgetfs even after gadgetfs has been unbound
from dummy_hcd's UDC and its private data structures have been
deallocated.

include/linux/usb/gadget.h documents that the ->reset, ->disconnect,
->suspend, and ->resume callbacks may be invoked in interrupt context.
In general this is necessary, to prevent races with gadget driver
removal.  This patch fixes dummy_hcd to retain the spinlock across
these calls, and it adds a spinlock acquisition to dummy_udc_stop() to
prevent the race.

The net2280 driver makes the same mistake of dropping the private
spinlock for its ->disconnect and ->reset callback invocations.  The
patch fixes it too.

Lastly, since gadgetfs_suspend() may be invoked in interrupt context,
it cannot assume that interrupts are enabled when it runs.  It must
use spin_lock_irqsave() instead of spin_lock_irq().  The patch fixes
that bug as well.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Andrey Konovalov <andreyknvl@google.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit f50b878f upstream.

A NULL-pointer dereference bug in gadgetfs was uncovered by syzkaller:

> kasan: GPF could be caused by NULL-ptr deref or user memory access
> general protection fault: 0000 [#1] SMP KASAN
> Dumping ftrace buffer:
>    (ftrace buffer empty)
> Modules linked in:
> CPU: 2 PID: 4820 Comm: syz-executor0 Not tainted 4.12.0-rc4+ #5
> Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
> task: ffff880039542dc0 task.stack: ffff88003bdd0000
> RIP: 0010:__list_del_entry_valid+0x7e/0x170 lib/list_debug.c:51
> RSP: 0018:ffff88003bdd6e50 EFLAGS: 00010246
> RAX: dffffc0000000000 RBX: 0000000000000000 RCX: 0000000000010000
> RDX: 0000000000000000 RSI: ffffffff86504948 RDI: ffffffff86504950
> RBP: ffff88003bdd6e68 R08: ffff880039542dc0 R09: ffffffff8778ce00
> R10: ffff88003bdd6e68 R11: dffffc0000000000 R12: 0000000000000000
> R13: dffffc0000000000 R14: 1ffff100077badd2 R15: ffffffff864d2e40
> FS:  0000000000000000(0000) GS:ffff88006dc00000(0000) knlGS:0000000000000000
> CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
> CR2: 000000002014aff9 CR3: 0000000006022000 CR4: 00000000000006e0
> Call Trace:
>  __list_del_entry include/linux/list.h:116 [inline]
>  list_del include/linux/list.h:124 [inline]
>  usb_gadget_unregister_driver+0x166/0x4c0 drivers/usb/gadget/udc/core.c:1387
>  dev_release+0x80/0x160 drivers/usb/gadget/legacy/inode.c:1187
>  __fput+0x332/0x7f0 fs/file_table.c:209
>  ____fput+0x15/0x20 fs/file_table.c:245
>  task_work_run+0x19b/0x270 kernel/task_work.c:116
>  exit_task_work include/linux/task_work.h:21 [inline]
>  do_exit+0x18a3/0x2820 kernel/exit.c:878
>  do_group_exit+0x149/0x420 kernel/exit.c:982
>  get_signal+0x77f/0x1780 kernel/signal.c:2318
>  do_signal+0xd2/0x2130 arch/x86/kernel/signal.c:808
>  exit_to_usermode_loop+0x1a7/0x240 arch/x86/entry/common.c:157
>  prepare_exit_to_usermode arch/x86/entry/common.c:194 [inline]
>  syscall_return_slowpath+0x3ba/0x410 arch/x86/entry/common.c:263
>  entry_SYSCALL_64_fastpath+0xbc/0xbe
> RIP: 0033:0x4461f9
> RSP: 002b:00007fdac2b1ecf8 EFLAGS: 00000246 ORIG_RAX: 00000000000000ca
> RAX: fffffffffffffe00 RBX: 00000000007080c8 RCX: 00000000004461f9
> RDX: 0000000000000000 RSI: 0000000000000000 RDI: 00000000007080c8
> RBP: 00000000007080a8 R08: 0000000000000000 R09: 0000000000000000
> R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
> R13: 0000000000000000 R14: 00007fdac2b1f9c0 R15: 00007fdac2b1f700
> Code: 00 00 00 00 ad de 49 39 c4 74 6a 48 b8 00 02 00 00 00 00 ad de
> 48 89 da 48 39 c3 74 74 48 c1 ea 03 48 b8 00 00 00 00 00 fc ff df <80>
> 3c 02 00 0f 85 92 00 00 00 48 8b 13 48 39 f2 75 66 49 8d 7c
> RIP: __list_del_entry_valid+0x7e/0x170 lib/list_debug.c:51 RSP: ffff88003bdd6e50
> ---[ end trace 30e94b1eec4831c8 ]---
> Kernel panic - not syncing: Fatal exception

The bug was caused by dev_release() failing to turn off its
gadget_registered flag after unregistering the gadget driver.  As a
result, when a later user closed the device file before writing a
valid set of descriptors, dev_release() thought the gadget had been
registered and tried to unregister it, even though it had not been.
This led to the NULL pointer dereference.

The fix is simple: turn off the flag when the gadget is unregistered.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit d2f48f05 upstream.

When plugging an USB webcam I see the following message:
[106385.615559] xhci_hcd 0000:04:00.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[106390.583860] handle_tx_event: 913 callbacks suppressed

With this patch applied, I get no more printing of this message.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit b72eb843 upstream.

xHCI host controllers can have both USB 3.1 and 3.0 extended speed
protocol lists. If the USB3.1 speed is parsed first and 3.0 second then
the minor revision supported will be overwritten by the 3.0 speeds and
the USB3 roothub will only show support for USB 3.0 speeds.

This was the case with a xhci controller with the supported protocol
capability listed below.
In xhci-mem.c, the USB 3.1 speed is parsed first, the min_rev of usb3_rhub
is set as 0x10.  And then USB 3.0 is parsed.  However, the min_rev of
usb3_rhub will be changed to 0x00. If USB 3.1 device is connected behind
this host controller, the speed of USB 3.1 device just reports 5G speed
using lsusb.

     00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F
  00 01 08 00 00 00 00 00 40 00 00 00 00 00 00 00 00
  10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
  20 02 08 10 03 55 53 42 20 01 02 00 00 00 00 00 00     //USB 3.1
  30 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
  40 02 08 00 03 55 53 42 20 03 06 00 00 00 00 00 00     //USB 3.0
  50 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
  60 02 08 00 02 55 53 42 20 09 0E 19 00 00 00 00 00     //USB 2.0
  70 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

This patch fixes the issue by only owerwriting the minor revision if
it is higher than the existing one.

[reword commit message -Mathias]
Signed-off-by: YD Tseng <yd_tseng@asmedia.com.tw>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 8128a31e upstream.

c2port_device_register() never returns NULL, it uses error pointers.

Link: http://lkml.kernel.org/r/20170412083321.GC3250@mwanda
Fixes: 65131cd5 ("c2port: add c2port support for Eurotech Duramar 2150")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Rodolfo Giometti <giometti@linux.it>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 1e9b71d5 upstream.

Recently, an unfinished patch was merged that added a third entry to the
beginning of the array of firmware locations without changing the code
to also look at the third element, thus pushing an old firmware location
off the list.

Fixes: 8af7779f ("[media] coda: add Freescale firmware compatibility location")
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit dd14a3e9 upstream.

The timeout for BULK packets was 300ms which is a long time if other
endpoints or devices are waiting for their turn. Changing it to 50ms
greatly increased the overall performance for multi-endpoint devices.

Fixes: 5d304358 ("usb: r8a66597-hcd: host controller driver for R8A6659")
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 1f873d85 upstream.

If multiple endpoints on a single device have pending IN URBs and one
endpoint times out due to NAKs (perfectly legal), select a different
endpoint URB to try.
The existing code only checked to see another device address has pending
URBs and ignores other IN endpoints on the current device address. This
leads to endpoints never getting serviced if one endpoint is using NAK as
a flow control method.

Fixes: 5d304358 ("usb: r8a66597-hcd: host controller driver for R8A6659")
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit d81182ce upstream.

Flag the first and only port as removable while also leaving the
remaining bits (including the reserved bit zero) unset in accordance
with the specifications:

	"Within a byte, if no port exists for a given location, the bit
	field representing the port characteristics shall be 0."

Also add a comment marking the legacy PortPwrCtrlMask field.

Fixes: 1cd8fd28 ("usb: gadget: dummy_hcd: add SuperSpeed support")
Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Cc: Tatyana Brokhman <tlinder@codeaurora.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 6830733d upstream.

The driver uses a relatively large data structure on the stack, which
showed up on my radar as we get a warning with the "latent entropy"
GCC plugin:

drivers/media/usb/pvrusb2/pvrusb2-eeprom.c:153:1: error: the frame size of 1376 bytes is larger than 1152 bytes [-Werror=frame-larger-than=]

The warning is usually hidden as we raise the warning limit to 2048
when the plugin is enabled, but I'd like to lower that again in the
future, and making this function smaller helps to do that without
build regressions.

Further analysis shows that putting an 'i2c_client' structure on
the stack is not really supported, as the embedded 'struct device'
is not initialized here, and we are only saved by the fact that
the function that is called here does not use the pointer at all.

Fixes: d855497e ("V4L/DVB (4228a): pvrusb2 to kernel 2.6.18")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit f1d6826c upstream.

Commit 08a36b54 ("usb: dwc3: gadget: simplify __dwc3_gadget_ep_queue()")
caused a small change in the way ISO transfer is handled in the case
when XferInProgress event happens on Isoc EP with an active transfer.
This caused a performance degradation of 50%. e.g. using g_webcam on DUT
and luvcview on host the video frame rate dropped from 16fps to 8fps
@high-speed.

Make the ISO transfer handling equivalent to that prior to that commit
to get back the original ISO performance numbers.

Fixes: 08a36b54 ("usb: dwc3: gadget: simplify __dwc3_gadget_ep_queue()")
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit ec963b41 upstream.

Fix up the root-hub descriptor to accommodate the variable-length
DeviceRemovable and PortPwrCtrlMask fields, while marking all ports as
removable (and leaving the reserved bit zero unset).

Also add a build-time constraint on VHCI_HC_PORTS which must never be
greater than USB_MAXCHILDREN (but this was only enforced through a
KConfig constant).

This specifically fixes the descriptor layout whenever VHCI_HC_PORTS is
greater than seven (default is 8).

Fixes: 04679b34 ("Staging: USB/IP: add client driver")
Cc: Takahiro Hirofuchi <hirofuchi@users.sourceforge.net>
Cc: Valentina Manea <valentina.manea.m@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 1a744d2e upstream.

Free memory allocated for address0_mutex if allocation of bandwidth_mutex
failed.

Fixes: feb26ac3 ("usb: core: hub: hub_port_init lock controller instead of bus")
Signed-off-by: Anton Bondarenko <anton.bondarenko.sama@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 93491ced upstream.

Add define for the maximum number of ports on a SuperSpeed hub as per
USB 3.1 spec Table 10-5, and use it when verifying the retrieved hub
descriptor.

This specifically avoids benign attempts to update the DeviceRemovable
mask for non-existing ports (should we get that far).

Fixes: dbe79bbe ("USB 3.0 Hub Changes")
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 940f538a upstream.

This controller disallows to change the PIPE until reading/writing
a packet finishes. However. the previous code is not enough to hold
the lock in some functions. So, this patch fixes it.

Fixes: 746bfe63 ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 067d6fdc upstream.

This patch fixes an issue that this driver is possible to cause
deadlock by double-spinclocked in renesas_usb3_stop_controller().
So, this patch removes spinlock API calling in renesas_usb3_stop().
(In other words, the previous code had a redundant lock.)

Fixes: 746bfe63 ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit cdc87687 upstream.

This patch fixes an issue that this driver is possible to access
the registers before pm_runtime_get_sync() if a gadget driver is
installed first. After that, oops happens on R-Car Gen3 environment.
To avoid it, this patch changes the pm_runtime call timing from
probe/remove to udc_start/udc_stop.

Fixes: 746bfe63 ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit f83914fd upstream.

Add missing endianness conversion when using the USB device-descriptor
bcdDevice field when applying the Amanero Combo384 (endianness!) quirk.

Fixes: 3eff682d ("ALSA: usb-audio: Support both DSD LE/BE Amanero firmware versions")
Cc: Jussi Laako <jussi@sonarnerd.net>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 12ee4022 upstream.

Geminilake is Skylake family platform. So add it's id to skl_plus check.

Fixes: 126cfa2f ("ALSA: hda: Add Geminilake HDMI codec ID")
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Cc: Senthilnathan Veppur <senthilnathanx.veppur@intel.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 5ba5b437 upstream.

We should be allocating enough information for a tiadc_device struct
which is about 400 bytes but instead we allocate enough for a second
iio_dev struct which is over 2000 bytes.

Fixes: fea89e2d ("iio: adc: ti_am335x_adc: use variable names for sizeof() operator")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 6272c0de upstream.

According to the datasheet the RCO must be recalibrated
on every power-on-reset. Also remove mutex locking in the
calibration function since callers other than the probe
function (which doesn't need it) will have a lock.

Fixes: 24ddb0e4 ("iio: Add AS3935 lightning sensor support")
Cc: George McCollister <george.mccollister@gmail.com>
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 2ccc1503 upstream.

This patch allows to avoid a transitory that occurs when a given sensor
has been already enabled (e.g. gyroscope) and the user is configuring
the sample frequency of the other one (e.g. accelerometer).
The transitory lasts until the accelerometer is enabled.
During that time slice the gyroscope ODR is incorrectly modified as well.
At the end of the transitory both sensors work at the right frequency.
Fix it introducing st_lsm6dsx_check_odr() routine to check ODR consistency
in write_raw handler in order to apply frequency configuration just
in st_lsm6dsx_set_odr()

Fixes: 290a6ce1 (iio: imu: add support to lsm6dsx driver)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit cf6c7732 upstream.

Standard deviation is calculated as the square root of the variance
where variance is the mean of sample_sum and length. Correct the
computation of statP->stddev in accordance to the proper calculation.

Fixes: 3c97c08b ("staging: iio: add TAOS tsl2x7x driver")
Reported-by: Abhiram Balasubramanian <abhiram@cs.utah.edu>
Signed-off-by: Eva Rachel Retuya <eraretuya@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 8e17858a upstream.

The unwinding here isn't right.  We don't free gdev[0] and instead
free 1 step past what was allocated.  Also we can't allocate "dev" then
we should unwind instead of returning directly.

Fixes: 7b3ad5ab ("staging: Import the BCM2835 MMAL-based V4L2 camera driver.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: walter harms <wharms@bfs.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 784047eb upstream.

The "len" could be as low as -14 so we should check for negatives.

Fixes: 9a7fe54d ("staging: r8188eu: Add source files for new driver - part 1")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit aaa22952 upstream.

The current page table dumper scans the Linux page tables and coalesces mappings
with adjacent virtual addresses and similar PTE flags. This behaviour is
somewhat broken when you consider the IOREMAP space where entirely unrelated
mappings will appear to be virtually contiguous. This patch modifies the range
coalescing so that only ranges that are both physically and virtually contiguous
are combined. This patch also adds to the dump output the physical address at
the start of each range.

Fixes: 8eb07b18 ("powerpc/mm: Dump linux pagetables")
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
[mpe: Print the physicall address with 0x like the other addresses]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 8c925b26 upstream.

The current way of building the of_physmap add-ons result in just
the add-on being in the object code, and not the actual core
implementation and regress the Gemini and Versatile.

Bake the physmap_of.o object by baking physmap_of_core.o and
adding the Versatile and/or Gemini add-ons to the final object.
Rename the source file physmap_of_core.c to get the desired
build components.
Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Fixes: 4f04f68e ("mtd: physmap_of: fixup gemini/versatile dependencies")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 441a681b upstream.

This patch fixes an issue that this driver doesn't take care of the runtime
PM. This code assumed that devm_phy_create() called pm_runtime_enable(dev),
but it misunderstood the dev_phy_create()'s specification.
This driver should call its own pm_runtime_enable() before
dev_phy_create().

Fixes: f3b5a8d9 ("phy: rcar-gen3-usb2: Add R-Car Gen3 USB2 PHY driver")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit be269180 upstream.

The cpcap INTS registers are for getting the value of the line,
not for configuring the type.

Fixes: 56e1d40d ("mfd: cpcap: Add minimal support")
Reviewed-By: Sebastian Reichel <sre@kernel.org>
Tested-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 5a88d412 upstream.

We should use ack_invert as the int_read_and_clear() in the Motorola
kernel tree does "ireg_val & ~mreg_val" before writing to the mask
register.

Fixes: 56e1d40d ("mfd: cpcap: Add minimal support")
Tested-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit ac894732 upstream.

I made a mistake assuming the device tree configuration for interrupt
triggering was somehow passed to the SPI device but it's not.

In the Motorola Linux kernel tree CPCAP PMIC is configured as a rising
edge triggered interrupt, but then then it's interrupt handler keeps
looping until the GPIO line goes down. So the CPCAP interrupt is clearly
a level interrupt and not an edge interrupt.

Earlier when I tried to configure it as level interrupt using the
device tree, I did not account that the triggering only gets passed
to the SPI core and it also needs to be specified in the CPCAP driver
when we do devm_regmap_add_irq_chip().

Fixes: 56e1d40d ("mfd: cpcap: Add minimal support")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 8461cf20 upstream.

commit b101829a029a ("mfd: axp20x: Fix AXP806 access errors on cold boot")
was intended to fix the case where a board uses an AXP806 in slave mode,
but the boot loader leaves it in master mode for lack of AXP806 support.
But now the driver breaks on boards where the PMIC is operating in master
mode. To let the device tree describe which mode of operation is needed,
this patch introduces a new property "xpowers,master-mode".

Fixes: 204ae296 ("mfd: axp20x: Add bindings for AXP806 PMIC")
Signed-off-by: Rask Ingemann Lambertsen <rask@formelder.dk>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit c0369698 upstream.

commit b101829a029a ("mfd: axp20x: Fix AXP806 access errors on cold boot")
was intended to fix the case where a board uses an AXP806 in slave mode,
but the boot loader leaves it in master mode for lack of AXP806 support.
But now the driver breaks on boards where the PMIC is operating in master
mode. This patch lets the driver use the new device tree property
"xpowers,master-mode" to set the correct operating mode for the board.

Fixes: 8824ee85 ("mfd: axp20x: Add support for AXP806 PMIC")
Signed-off-by: Rask Ingemann Lambertsen <rask@formelder.dk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>