- 24 Apr, 2022 1 commit
-
-
Ping-Ke Shih authored
8852CE uses different but similar IMR/ISR registers, and its masks are also different in various states, so add config_intr_mask ops to configure masks according to under_recovery or low_power states. Signed-off-by:
Ping-Ke Shih <pkshih@realtek.com> Signed-off-by:
Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20220421120903.73715-2-pkshih@realtek.com
-
- 23 Apr, 2022 23 commits
-
-
Po-Hao Huang authored
Disable this capability to avoid timeout errors on certain platforms. Without it, pci bus might stuck and leads to disconnection. Signed-off-by:
Po-Hao Huang <phhuang@realtek.com> Signed-off-by:
Chris Chiu <chris.chiu@canonical.com> Signed-off-by:
-
Po-Hao Huang authored
This avoids below warning and makes compiler happy. error: uninitialized symbol 'tim_offset' Signed-off-by:
-
Minghao Chi authored
Using pm_runtime_resume_and_get() to replace pm_runtime_get_sync and pm_runtime_put_noidle. This change is just to simplify the code, no actual functional changes. Reported-by:
Zeal Robot <zealci@zte.com.cn> Signed-off-by:
Minghao Chi <chi.minghao@zte.com.cn> Signed-off-by:
-
Minghao Chi authored
Using pm_runtime_resume_and_get() to replace pm_runtime_get_sync and pm_runtime_put_noidle. This change is just to simplify the code, no actual functional changes. Reported-by:
-
Ping-Ke Shih authored
During setting channel, we need to backup/restore and disable/enable some settings. The settings include SCH (scheduler channel), PPDU status report, and RF components, DFS and ADC. Signed-off-by:
-
Ping-Ke Shih authored
BB does many settings during setting channel. First is to configure CCK for 2G channels, and then basic channel and bandwidth settings with a encoded channel index that will report to driver when we receive packets. Configure spur elimination to avoid spur of CSI and NBI tones in certain frequencies. Also, it initializes BT grant to arrange path sharing with BT according to band. Finally, reset TSSI and BB hardware to ensure it stays in initial state. Signed-off-by:
-
Ping-Ke Shih authored
Configure channel and bandwidth of MAC registers to work properly. Signed-off-by:
-
Ping-Ke Shih authored
Prepare functions to configure channel and bandwidth accordingly. Signed-off-by:
-
Ping-Ke Shih authored
HFC is short for HCI flow control, and these parameters is used to configure PCI quota for TX/RX. Signed-off-by:
-
Ping-Ke Shih authored
Define efuse struct to access gain offset, and store them for further use by setting channel. Signed-off-by:
-
Zong-Zhe Yang authored
Add parser for bb gain table and configure bb gain table for 8852c. While ctrl_ch, obtain bb gain error settings and write them to phy. Signed-off-by:
Zong-Zhe Yang <kevin_yang@realtek.com> Signed-off-by:
-
Ping-Ke Shih authored
chip_ops::bb_sethw is to initialize BB settings out of BB parameters tables. Once switching channel or initialing, we do chip_ops::bb_reset to reset hardware counters and states to make things in expectation. Signed-off-by:
-
Ping-Ke Shih authored
TSSI is used to manage TX power with thermal value as a factor. This patch is to configure bandedge to TX proper waveform. Signed-off-by:
-
Zong-Zhe Yang authored
TX power track tables are used to do TX power compensation according to thermal value. In order to work in existing and new chip, add new 6G entries, and change type from u8 to s8. Internal version table is HALRF_027_00_031. Signed-off-by:
-
Ping-Ke Shih authored
TX power depends on rate, but must follow regulation for specific country. Once asked to set channel, we configure registers according to these TX power tables. Signed-off-by:
-
Ping-Ke Shih authored
These parameters are used to initialize BB and RF hardware when we are going to bring up interface and start to transmit and receive. Signed-off-by:
-
Minghao Chi authored
Using pm_runtime_resume_and_get is more appropriate for simplifing code Reported-by:
-
Minghao Chi authored
Using pm_runtime_resume_and_get() to replace pm_runtime_get_sync and pm_runtime_put_noidle. This change is just to simplify the code, no actual functional changes. Reported-by:
-
Minghao Chi authored
Using pm_runtime_resume_and_get() to replace pm_runtime_get_sync and pm_runtime_put_noidle. This change is just to simplify the code, no actual functional changes. Reported-by:
-
Minghao Chi authored
Using pm_runtime_resume_and_get is more appropriate for simplifing code Reported-by:
-
Minghao Chi authored
Using pm_runtime_resume_and_get is more appropriate for simplifing code Reported-by:
-
Minghao Chi authored
Using pm_runtime_resume_and_get is more appropriate for simplifing code Reported-by:
-
Minghao Chi authored
Using pm_runtime_resume_and_get is more appropriate for simplifing code Reported-by:
-
- 13 Apr, 2022 4 commits
-
-
Ping-Ke Shih authored
Fix wrong checking statement. Fortunately, this wrong code doesn't affect existing chip. Fixes: 740c431c ("rtw89: pci: add register definition to rtw89_pci_info to generalize pci code") Signed-off-by:
-
Ping-Ke Shih authored
Add to configure security CAM while mac80211 calls set_key and del_key. Signed-off-by:
-
Ping-Ke Shih authored
DCTL is short for D-MAC control that V1 chip uses this H2C to configure security CAM. Implement the callers in next patch. Signed-off-by:
-
Ping-Ke Shih authored
In order to support new chip that has capability of 160M, we need new format to fill new information, so add a new V1 ID for newer use. Since most fields are the same, fill fields according to the function ID of chip. Signed-off-by:
-
- 12 Apr, 2022 12 commits
-
-
Kalle Valo authored
This is an immutable branch shared between wireless-next and staging-next for moving wfx driver out of staging to drivers/net/wireless directory.
-
Lv Ruyi authored
There are some spelling mistakes in the comments. Fix it. Reported-by:
Lv Ruyi <lv.ruyi@zte.com.cn> Acked-by:
-
Lv Ruyi authored
There are some spelling mistakes in the comments. Fix it. Reported-by:
-
Minghao Chi authored
Using pm_runtime_resume_and_get is more appropriate for simplifing code Reported-by:
-
Jimmy Hon authored
Make workaround work for other 8821CE devices with different PCI ID Signed-off-by:
Jimmy Hon <honyuenkwun@gmail.com> Reviewed-by:
-
Jimmy Hon authored
New device ID 0xb821 found on TP-Link T2E Tested it with c821 driver. 2.4GHz and 5GHz works. PCI id: 05:00.0 Network controller: Realtek Semiconductor Co., Ltd. Device b821 Subsystem: Realtek Semiconductor Co., Ltd. Device b821 Signed-off-by: -
Po-Hao Huang authored
RSSI value per frame is reported to mac80211 but not maintained in our own statistics, add it back to help us debug. Signed-off-by:
-
Ping-Ke Shih authored
Calling calibration to yield expected PHY performance. We do this in STA mode, so do this in AP mode as well. Signed-off-by:
-
Po-Hao Huang authored
Without this setting, hardware would not report to driver even if management frames are transmitted successfully. So we fix it. Signed-off-by:
-
Po-Hao Huang authored
To support stations in power saving mode, AP should notify stations that there are frames buffered at the AP via TIM during beacons. Driver used to transmit identical beacons that were downloaded to hardware during the initiation phase. This beacon will become obsolete over time. If the beacon does not contain sufficient information, station would not be able to percept that there is data to receive. Hence it won't wake up and start the PS-poll procedure, this could lead to timeout and/or lost data segments. In order to resolve this issue, driver will now download beacon to hardware whenever the content is updated. Enable hardware to update dtim_count for more efficiency, this reduces the overhead of downloading beacon at every beacon interval since most of the time only the dtim_count needs to be updated. Change queue mapping for broadcast/multicast frames to high queue, so these frames can be prioritized and sent when dtim_count is zero. Signed-off-by:
-
Po-Hao Huang authored
We should only fill in frequency reported by firmware during scan. Add this so frames won't be dropped by mac80211 due to frequency mismatch. Signed-off-by:
-
Po-Hao Huang authored
Adding this allows us to get notification when bitrate configuration of the station changes. Update according parameters to firmware so the rate control algorithm can work properly. Signed-off-by:
-
