- 27 Jan, 2022 40 commits
-
-
Christophe JAILLET authored
As stated in [1], dma_set_mask() with a 64-bit mask never fails if dev->dma_mask is non-NULL. So, if it fails, the 32 bits case will also fail for the same reason. Simplify code and remove some dead code accordingly. [1]: https://lkml.org/lkml/2021/6/7/398Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by:
Christoph Hellwig <hch@lst.de> Reviewed-by:
Alexander Lobakin <alexandr.lobakin@intel.com> Tested-by:
Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by:
Tony Nguyen <anthony.l.nguyen@intel.com>
-
Christophe JAILLET authored
As stated in [1], dma_set_mask() with a 64-bit mask never fails if dev->dma_mask is non-NULL. So, if it fails, the 32 bits case will also fail for the same reason. So, if dma_set_mask_and_coherent() succeeds, 'pci_using_dac' is known to be 1. Simplify code and remove some dead code accordingly. [1]: https://lkml.org/lkml/2021/6/7/398Signed-off-by:
-
Christophe JAILLET authored
As stated in [1], dma_set_mask() with a 64-bit mask never fails if dev->dma_mask is non-NULL. So, if it fails, the 32 bits case will also fail for the same reason. Simplify code and remove some dead code accordingly. [1]: https://lkml.org/lkml/2021/6/7/398Signed-off-by:
Gurucharan G <gurucharanx.g@intel.com> Signed-off-by:
-
Christophe JAILLET authored
As stated in [1], dma_set_mask() with a 64-bit mask never fails if dev->dma_mask is non-NULL. So, if it fails, the 32 bits case will also fail for the same reason. So, if dma_set_mask_and_coherent() succeeds, 'pci_using_dac' is known to be 1. Simplify code and remove some dead code accordingly. [1]: https://lkml.org/lkml/2021/6/7/398Signed-off-by:
-
Christophe JAILLET authored
As stated in [1], dma_set_mask() with a 64-bit mask never fails if dev->dma_mask is non-NULL. So, if it fails, the 32 bits case will also fail for the same reason. So, if dma_set_mask_and_coherent() succeeds, 'pci_using_dac' is known to be 1. Simplify code and remove some dead code accordingly. [1]: https://lkml.org/lkml/2021/6/7/398Signed-off-by:
-
Christophe JAILLET authored
As stated in [1], dma_set_mask() with a 64-bit mask never fails if dev->dma_mask is non-NULL. So, if it fails, the 32 bits case will also fail for the same reason. So, if dma_set_mask_and_coherent() succeeds, 'pci_using_dac' is known to be 1. Simplify code and remove some dead code accordingly. [1]: https://lkml.org/lkml/2021/6/7/398Signed-off-by:
-
Yang Guang authored
coccinelle report: ./drivers/ptp/ptp_sysfs.c:17:8-16: WARNING: use scnprintf or sprintf ./drivers/ptp/ptp_sysfs.c:390:8-16: WARNING: use scnprintf or sprintf Use sysfs_emit instead of scnprintf or sprintf makes more sense. Reported-by:
Zeal Robot <zealci@zte.com.cn> Signed-off-by:
Yang Guang <yang.guang5@zte.com.cn> Signed-off-by:
David Yang <davidcomponentone@gmail.com> Acked-by:
Richard Cochran <richardcochran@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Heiner Kallweit authored
On some systems there are compatibility issues with ASPM L1.2 and RTL8125, therefore this state is disabled per default. To allow for the L1.2 power saving on not affected systems, Realtek provides vendors that successfully tested ASPM L1.2 the option to flag this state as safe. According to Realtek this flag will be set first on certain Chromebox devices. Suggested-by:
Chun-Hao Lin <hau@realtek.com> Signed-off-by:
Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by:
-
David S. Miller authored
Jakub Kicinski says: ==================== net: get rid of unused static inlines I noticed a couple of unused static inline functions reviewing net/sched patches so I run a grep thru all of include/ and net/ to catch other cases. This set removes the cases which look like obvious dead code. ==================== Signed-off-by: -
Jakub Kicinski authored
IIUC the TIPC msg helpers are not meant to provide and exhaustive API, so remove the unused ones. Signed-off-by:
Jakub Kicinski <kuba@kernel.org> Signed-off-by:
-
Jakub Kicinski authored
Never used since it was added in v5.2. Signed-off-by:
-
Jakub Kicinski authored
Not used since v3.9. Signed-off-by:
-
Jakub Kicinski authored
Not used since v5.10. Signed-off-by:
-
Jakub Kicinski authored
Not used since v4.0. Signed-off-by:
-
Jakub Kicinski authored
Not used since added in v3.8. Signed-off-by:
Willem de Bruijn <willemb@google.com> Signed-off-by:
-
Jakub Kicinski authored
Not used since v2.6.37. Signed-off-by:
-
Jakub Kicinski authored
The stubs under !CONFIG_IPV6 were missed when real functions got deleted ca. v3.13. Signed-off-by:
-
Jakub Kicinski authored
get_prp_lan_id() has never been used. Signed-off-by:
-
Jakub Kicinski authored
Nothing takes the refcount since v4.9. Signed-off-by:
-
Jakub Kicinski authored
No caller since v3.16. Signed-off-by:
-
Jakub Kicinski authored
No callers since v5.7, the initial use case seems pretty esoteric so removing this should not harm the completeness of the API. Signed-off-by:
-
Jakub Kicinski authored
No callers since v3.15. Signed-off-by:
-
Jakub Kicinski authored
NCI and HCI wrappers for nfc_set_vendor_cmds() exist, use them. We could also remove the helpers. It's a coin toss. Signed-off-by:
Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Signed-off-by:
-
Jakub Kicinski authored
The only caller of mii_lpa_to_linkmode_lpa_sgmii() disappeared in v5.10. Signed-off-by:
-
Robin Murphy authored
Prefer kcalloc() to kzalloc(array_size()) for allocating an array. Signed-off-by:
Robin Murphy <robin.murphy@arm.com> Acked-by:
Simon Horman <simon.horman@corigine.com> Signed-off-by:
-
Lorenzo Bianconi authored
Fix the following warning in mtk_star_emac.c if CONFIG_OF is not set: drivers/net/ethernet/mediatek/mtk_star_emac.c:1559:34: warning: unused variable 'mtk_star_of_match' [-Wunused-const-variable] static const struct of_device_id mtk_star_of_match[] = { Signed-off-by:Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by:
-
David S. Miller authored
Tobias Waldekranz says: ==================== net/fsl: xgmac_mdio: Preamble suppression and custom MDC frequencies The first patch removes the docs for a binding that has never been supported by the driver as far as I can see. This is a bit of a mystery to me, maybe Freescale/NXP had/has support for it in an internal version? We then start working on the xgmac_mdio driver, converting the driver to exclusively use managed resources, thereby simplifying the error paths. Suggested by Andrew. Preamble suppression is then added, followed by MDC frequency customization. Neither code will change any bits if the corresponding dt properties are not specified, so as to not trample on any setup done by the bootloader, which boards might have relied on up to now. Finally, we document the new bindings. Tested on a T1023 based board. ==================== Signed-off-by: -
Tobias Waldekranz authored
The driver now supports the standard "clock-frequency" and "suppress-preamble" properties, do document them in the binding description. Signed-off-by:
Tobias Waldekranz <tobias@waldekranz.com> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
-
Tobias Waldekranz authored
Support the standard "clock-frequency" attribute to set the generated MDC frequency. If not specified, the driver will leave the divisor bits untouched. Signed-off-by:
-
Tobias Waldekranz authored
Support the standard "suppress-preamble" attribute to disable preamble generation. Signed-off-by:
-
Tobias Waldekranz authored
All of the resources used by this driver has managed interfaces, so use them. Heed the warning in the comment before platform_get_resource and use a bare devm_ioremap to allow for non-exclusive access to the IO memory. Signed-off-by:
-
Tobias Waldekranz authored
This property has never been supported by the driver. The kernel has settled on "clock-frequency" as the standard name for this binding, so once that is supported we will document that instead. Fixes: 7f93c9d9 ("power/fsl: add MDIO dt binding for FMan") Signed-off-by:
-
xu xin authored
Different netns has different requirement on the setting of min_adv_mss sysctl which the advertised MSS will be never lower than. Enable min_adv_mss to be configured per network namespace. Signed-off-by:
xu xin <xu.xin16@zte.com.cn> Signed-off-by:
-
David S. Miller authored
Russell King says: ==================== net: mvneta: use .mac_select_pcs() This series converts mvneta to use the .mac_select_pcs() like eventually everything else will be. mvneta is slightly more involved because we need to rearrange the initialisation first to ensure everything required is initialised prior to phylink_create() being called. Tested locally on SolidRun Clearfog. ==================== Signed-off-by: -
Russell King (Oracle) authored
Convert mvneta to use the mac_select_interface rather than using phylink_set_pcs(). The intention here is to unify the approach for PCS and eventually remove phylink_set_pcs(). Signed-off-by:
Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by:
-
Russell King (Oracle) authored
Re-order the mvneta initialisation to move devm based resources and easy setup earlier in the probe function. The primary reason for this is to allow us to switch the driver to use phylink's mac_select_pcs() callback. Signed-off-by:
-
David S. Miller authored
Robert Hancock says: ==================== at803x fiber/SFP support Add support for 1000Base-X fiber modes to the at803x PHY driver, as well as support for connecting a downstream SFP cage. Changes since v3: -Renamed some constants with OHM suffix for clarity Changes since v2: -fixed tabs/spaces issue in one patch Changes since v1: -moved page selection to config_init so it is handled properly after suspend/resume -added explicit check for empty sfp_support bitmask ==================== Signed-off-by: -
Robert Hancock authored
Add support for downstream SFP cages for AR8031 and AR8033. This is primarily intended for fiber modules or direct-attach cables, however copper modules which work in 1000Base-X mode may also function. Such modules are allowed with a warning. Signed-off-by:
Robert Hancock <robert.hancock@calian.com> Signed-off-by:
-
Robert Hancock authored
Previously this driver always forced the copper page to be selected, however for AR8031 in 100Base-FX or 1000Base-X modes, the fiber page needs to be selected. Set the appropriate mode based on the hardware mode_cfg strap selection. Enable the appropriate interrupt bits to detect fiber-side link up or down events. Update config_aneg and read_status methods to use the appropriate Clause 37 calls when fiber mode is in use. Signed-off-by:
-
Robert Hancock authored
The fix to select the copper page on AR8031 was being done in the probe function rather than config_init, so it would not be redone after resume from suspend. Move this to config_init so it is always redone when needed. Fixes: c329e5af ("net: phy: at803x: select correct page on config init") Signed-off-by:
-
