- 05 Jan, 2023 6 commits
-
-
Praful Swarnakar authored
[Why & How] Remove redundant log in DSC that just add additional blank prints Signed-off-by:
Praful Swarnakar <praful.swarnakar@amd.com> Signed-off-by:
Hamza Mahfooz <hamza.mahfooz@amd.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com>
-
Wen Yang authored
The following errors occurred when using gcc 7.5.0-3ubuntu1~18.04: drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_stream.c: In function ‘dc_stream_remove_writeback’: drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_stream.c:543:55: warning: array subscript is above array bounds [-Warray-bounds] stream->writeback_info[j] = stream->writeback_info[i]; ~~~~~~~~~~~~~~~~~~~~~~^~~ Add a check to make sure that num_wb_info won't overflowing the writeback_info buffer. Fixes: 6fbefb84 ("drm/amd/display: Add DC core changes for DCN2") Signed-off-by:
Wen Yang <wenyang.linux@foxmail.com> Cc: Aurabindo Pillai <aurabindo.pillai@amd.com> Cc: Hamza Mahfooz <hamza.mahfooz@amd.com> Cc: Guenter Roeck <linux@roeck-us.net> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: Harry Wentland <harry.wentland@amd.com> Cc: Leo Li <sunpeng.li@amd.com> Cc: amd-gfx@lists.freedesktop.org Cc: dri-devel@lists.freedesktop.org Cc: linux-kernel@vger.kernel.org Signed-off-by:
-
Alexey Kodanev authored
pipe_ctx pointer cannot be NULL when getting the address of an element of the pipe_ctx array. Moreover, the MAX_PIPES is defined as 6, so pipe_ctx is not NULL after the loop either. Detected using the static analysis tool - Svace. Signed-off-by:
Alexey Kodanev <aleksei.kodanev@bell-sw.com> Signed-off-by:
-
Hawking Zhang authored
amdgpu_ras_block_late_init will be invoked in IP specific ras_late_init call as a common helper for all the IP blocks. However, when amdgpu_ras_block_late_init call amdgpu_ras_query_error_count to query ras error counters, amdgpu_ras_query_error_count queries all the IP blocks that support ras query interface. This results to wrong error counters cached in software copies when there are ras errors detected at time zero or warm reset procedure. i.e., in sdma_ras_late_init phase, it counts on sdma/mmhub errors, while, in mmhub_ras_late_init phase, it still counts on sdma/mmhub errors. The change updates amdgpu_ras_query_error_count interface to allow query specific ip error counter. It introduces a new input parameter: query_info. if query_info is NULL, it means query all the IP blocks, otherwise, only query the ip block specified by query_info. Signed-off-by:
Hawking Zhang <Hawking.Zhang@amd.com> Reviewed-by:
Tao Zhou <tao.zhou1@amd.com> Signed-off-by:
-
xurui authored
HPD signals on DVI ports can be fired off before the pins required for DDC probing actually make contact, due to the pins for HPD making contact first. This results in a HPD signal being asserted but DDC probing failing, resulting in hotplugging occasionally failing. Rescheduling the hotplug work for a second when we run into an HPD signal with a failing DDC probe usually gives enough time for the rest of the connector's pins to make contact, and fixes this issue. Signed-off-by:
xurui <xurui@kylinos.cn> Signed-off-by:
-
Alex Deucher authored
A number of the gfx8 cases were the same. Clean them up. Reviewed-by:
Felix Kuehling <Felix.Kuehling@amd.com> Signed-off-by:
-
- 03 Jan, 2023 27 commits
-
-
Randy Dunlap authored
Fix all kernel-doc warnings in dc/core/dc.c: dc.c:385: warning: missing initial short description on line: * dc_stream_adjust_vmin_vmax: dc.c:392: warning: contents before sections dc.c:399: warning: No description found for return value of 'dc_stream_adjust_vmin_vmax' dc.c:434: warning: Excess function parameter 'adjust' description in 'dc_stream_get_last_used_drr_vtotal' dc.c:434: warning: No description found for return value of 'dc_stream_get_last_used_drr_vtotal' dc.c:574: warning: No description found for return value of 'dc_stream_configure_crc' dc.c:1746: warning: No description found for return value of 'dc_commit_state_no_check' dc.c:4991: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst * dc_extended_blank_supported 0 Decide whether extended blank is supported dc.c:4991: warning: missing initial short description on line: * dc_extended_blank_supported 0 Decide whether extended blank is supported dc.c:4723: warning: Function parameter or member 'dc' not described in 'dc_enable_dmub_outbox' dc.c:4926: warning: Function parameter or member 'dc' not described in 'dc_process_dmub_dpia_hpd_int_enable' dc.c:4926: warning: Function parameter or member 'hpd_int_enable' not described in 'dc_process_dmub_dpia_hpd_int_enable' 12 warnings Signed-off-by:
Randy Dunlap <rdunlap@infradead.org> Reported-by:
kernel test robot <lkp@intel.com> Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: Hamza Mahfooz <hamza.mahfooz@amd.com> Cc: Harry Wentland <harry.wentland@amd.com> Cc: Leo Li <sunpeng.li@amd.com> Cc: Christian König <christian.koenig@amd.com> Cc: "Pan, Xinhui" <Xinhui.Pan@amd.com> Cc: amd-gfx@lists.freedesktop.org Signed-off-by:
-
Michel Dänzer authored
This reverts commit de05abe6. The bug referenced below was bisected to this commit. There has been no activity toward fixing it in 3 months, so let's revert for now. Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/2162Signed-off-by:
Michel Dänzer <mdaenzer@redhat.com> Signed-off-by:
-
Jiapeng Chong authored
The function dmub_outbox_irq_info_funcs is defined in the irq_service_dcn201.c file, but not called elsewhere, so remove this unused function. drivers/gpu/drm/amd/amdgpu/../display/dc/irq/dcn201/irq_service_dcn201.c:139:43: warning: unused variable 'dmub_outbox_irq_info_funcs'. Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=3520Reported-by:
Abaci Robot <abaci@linux.alibaba.com> Signed-off-by:
Jiapeng Chong <jiapeng.chong@linux.alibaba.com> Signed-off-by:
-
Bhawanpreet Lakha authored
[Why] We skip dsc_validation on pipes that are underlays, but in the acquire_dsc code we don't have this check. In certain conditions (when underlay pipe index is lower) we will assign the dsc resource to the underlay pipe and skip the base pipe. Now during dsc_validation we will skip the underlay pipe (this has the dsc resource) but try to validate the base pipe(this doesn't have a dsc resource) due to this mismatch we hit a NULLPTR [How] In the acquire_dsc add a check for underlay pipe so we don't acquire a dsc resource for this pipe. This will match the acquire/validation conditions. Reviewed-by:
Wenjing Liu <Wenjing.Liu@amd.com> Reviewed-by:
Hersen Wu <Hersenxs.Wu@amd.com> Acked-by:
Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by:
-
Stanley.Yang authored
[Why] [ 41.285804] RIP: 0010:amdgpu_ras_feature_enable+0x15c/0x310 [amdgpu] [ 41.285945] Code: 48 89 c1 48 c7 c2 b9 f2 88 c1 48 c7 c0 c0 f2 88 c1 49 8b 3c 24 48 0f 44 d0 48 c7 c6 98 33 80 c1 e8 5f 52 75 d9 e9 fa fe ff ff <0f> 0b e9 66 ff ff ff 48 8b 3d 86 8c 0f da ba 00 04 00 00 be c0 0d [ 41.285946] RSP: 0018:ffffbccdc72efc90 EFLAGS: 00010246 [ 41.285948] RAX: 0000000000000004 RBX: ffff931897406980 RCX: 0000000000000002 [ 41.285949] RDX: 0000000000000dc0 RSI: 0000000000000002 RDI: ffff931500042b00 [ 41.285950] RBP: ffffbccdc72efcc0 R08: 0000000000000002 R09: ffff931885b87000 [ 41.285951] R10: 0000000000ffff10 R11: 0000000000000001 R12: ffff931893e20000 [ 41.285952] R13: 0000000000000001 R14: ffff931885b87000 R15: 0000000000000000 [ 41.285953] FS: 0000000000000000(0000) GS:ffff931c6f200000(0000) knlGS:0000000000000000 [ 41.285954] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 41.285955] CR2: 000055dd6f532008 CR3: 000000061b010006 CR4: 00000000003706e0 [ 41.285956] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 41.285957] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 41.285958] Call Trace: [ 41.285959] <TASK> [ 41.285963] ? gfx_v11_0_early_init+0x250/0x250 [amdgpu] [ 41.286117] gfx_v11_0_late_init+0x8c/0xb0 [amdgpu] [ 41.286271] amdgpu_device_ip_late_init+0x8d/0x3c0 [amdgpu] [ 41.286401] amdgpu_device_init.cold+0x1677/0x1fda [amdgpu] [ 41.286616] ? pci_bus_read_config_word+0x4a/0x70 [ 41.286621] ? do_pci_enable_device+0xdb/0x110 [ 41.286625] amdgpu_driver_load_kms+0x1a/0x160 [amdgpu] [ 41.286762] amdgpu_pci_probe+0x18d/0x3a0 [amdgpu] [ 41.286898] local_pci_probe+0x4b/0x90 [ 41.286901] work_for_cpu_fn+0x1a/0x30 [ 41.286903] process_one_work+0x22b/0x3d0 [ 41.286905] worker_thread+0x223/0x420 [ 41.286907] ? process_one_work+0x3d0/0x3d0 [ 41.286908] kthread+0x12a/0x150 [ 41.286911] ? set_kthread_struct+0x50/0x50 [ 41.286913] ret_from_fork+0x22/0x30 [How] For specific asic, only mem ecc is enabled, sram ecc is not enabled, but it still need to send ras enable cmd to gfx block to support poison mode, so add check posion mode. Signed-off-by:Stanley.Yang <Stanley.Yang@amd.com> Reviewed-by:
-
Stanley.Yang authored
For GFX 11.0.3, Due to security policy, there is no way to check UcFatalEn field of UMCCH0_0_GeccCtrl to identify UMC poison mode. This is workaround force set umc poison mode as 1 for GFX 11.0.3 Signed-off-by:
-
Aric Cyr authored
Acked-by:
Aurabindo Pillai <aurabindo.pillai@amd.com> Signed-off-by:
Aric Cyr <aric.cyr@amd.com> Tested-by:
Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by:
-
Aric Cyr authored
[why & how] By moving bw_ctx field to the end of the dc_state the state can be cleared more efficiently without resulting in large DML memcpy operations, resulting in better mode enumeration performance on some platforms. Acked-by:
Nevenko Stupar <Nevenko.Stupar@amd.com> Tested-by:
-
Leo Chen authored
[Why & How] For certain features, there will be more implementations needed in the if-block. Braces are added as part of the preparation. Acked-by:
Leo Chen <sancchen@amd.com> Reviewed-by:
Charlene Liu <Charlene.Liu@amd.com> Tested-by:
-
Aurabindo Pillai authored
[Why&How] ignore_msa_timing_param is used by SubVP logic to determine if SubVP + DRR is possible. Linux does not support freesync on multi display config, which results in incorrect assumption of VRR support if we set this parameter when VRR is supported, but not enabled. Signed-off-by:
Rodrigo Siqueira <rodrigo.siqueira@amd.com> Tested-by:
-
Wenjing Liu authored
[why] During DP2.1 LL CTS if test equipment requests to change between DP2.1 and DP1.4 link rates, we need to swap between HPO and DIO encoders by remapping encoder resource. [how] Add a function dc resource to update encoder resources and toggle dpms state for all enabled stream associated witht the link under test. Acked-by:
Jun Lei <Jun.Lei@amd.com> Tested-by:
-
Wenjing Liu authored
[why] Pixel rate div depends on the type of encoder that we are enabling stream with. If we swap between HPO and DIO encoder at the time we call enable stream for the new encoder, we must reprogram pixel rate div based on the new encoder type. Acked-by:
-
Wenjing Liu authored
[why] dccg clock programming shouldn't be part of link hwss programming sequence. The scope of link hwss is limited to encoder and phy programming. Acked-by:
-
Dmytro Laktyushkin authored
This function is meant to be used on multi-edp systems and only makes sense if only links with connected panels are considered. Acked-by:
Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com> Tested-by:
-
Nicholas Kazlauskas authored
[Why] On some monitors we see a brief flash of corruption during the monitor disable sequence caused by FIFO being disabled in the middle of an active DP stream. [How] Wait until DP vid stream is disabled before turning off the FIFO. The FIFO reset on DP unblank should take care of clearing any FIFO error, if any. Acked-by:
Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Reviewed-by:
Syed Hassan <Syed.Hassan@amd.com> Tested-by:
-
Swapnil Patel authored
[Why] DCN301 resource function is missing function pointer to handle cases with unknown plane state. This causes assertion when global state is validated while using swizzle parameter as “DC_UNKNOWN” [How] Add function pointer to handle and patch cases when plane state is unknown. Acked-by:
Swapnil Patel <Swapnil.Patel@amd.com> Reviewed-by:
Sung joon Kim <Sungjoon.Kim@amd.com> Tested-by:
-
Alvin Lee authored
[Description] - Proper phantom pipe disable sequence was missing in commit_planes_for_stream - If disabling phantom pipe, turn on phantom OTG first, and turn off the phantom OTG after the plane is disabled - Also update sequence for enabling / disabling phantom streams (apply_ctx_to_hw). When enabling phantom pipes, enable before doing front end programming for phantom pipes. If disabling phantom pipes, disable after front end programming (i.e. after phantom plane disable) - TODO: Still need to properly handle transition case when a phantom pipe is transitioned directly into a real pipe (need to fully disable the phantom pipe first) Acked-by:
Alvin Lee <Alvin.Lee2@amd.com> Reviewed-by:
-
Alan Liu authored
[Why] - Need error message when failing to allocating secure_display_ctx. - Need to check if secure display context in psp is initialized or not before using it. [How] - Add error message when memory allocation fail. - Add check before accessing psp secure display context. Acked-by:
Alan Liu <HaoPing.Liu@amd.com> Reviewed-by:
Wayne Lin <Wayne.Lin@amd.com> Tested-by:
-
Samson Tam authored
[Why] SwathSizePerSurfaceY[] and SwathSizePerSurfaceC[] values are uninitialized because we are using += instead of = operator. [How] Assign values in loop with = operator. Acked-by:
Samson Tam <samson.tam@amd.com> Reviewed-by:
-
hersen wu authored
[Why] multiple display hdcp are enabled within event_property_validate, event_property_update by looping all displays on mst hub. when one of display on mst hub in unplugged or disabled, hdcp are disabled for all displays on mst hub within hdcp_reset_display by looping all displays of mst link. for displays still active, their encryption status are off. kernel driver will not run hdcp authentication again. therefore, hdcp are not enabled automatically. [How] within is_content_protection_different, check drm_crtc_state changes of all displays on mst hub, if need, triger hdcp_update_display to re-run hdcp authentication. Acked-by:
-
Christian König authored
This allows testing the driver without any VRAM. Signed-off-by:
Christian König <christian.koenig@amd.com> Acked-by:
Luben Tuikov <luben.tuikov@amd.com> Acked-by:
-
Christian König authored
Centralize the limit handling and validation in one place instead of spreading that around in different hw generations. Signed-off-by:
-
Christian König authored
Rename vram_scratch into mem_scratch and allow allocating it into GTT as well. The only problem with that is that we won't have a default page for the system aperture any more. Signed-off-by:
-
Christian König authored
Technically all of those can use GTT as well, no need to force things into VRAM. Signed-off-by:
-
Saleemkhan Jamadar authored
Enable VCN Dynamic Power Gating control for GC IP v11.0.4. Signed-off-by:
Saleemkhan Jamadar <saleemkhan.jamadar@amd.com> Reviewed-by:
Veerabadhran Gopalakrishnan <veerabadhran.gopalakrishnan@amd.com> Signed-off-by:
-
Likun Gao authored
1.Drop soft reset check when do should recover gpu check. (As it will skip gpu reset operation if some ip is hang but not support soft reset) 2.Check soft reset status before do soft reset when pre asic reset. a. If check soft reset return true, it means: some ip is hang and it also support soft reset, will try soft reset first. b. If check soft reset return false, it means: I. All the ip are not hang, will skip gpu reset. II. Some ip is hang but not support soft reset, will skip soft reset and retry with full reset later. Signed-off-by:Likun Gao <Likun.Gao@amd.com> Reviewed-by:
-
Mukul Joshi authored
This patch fixes the following kernel warning seen during driver load by correctly initializing the p2plink attr before creating the sysfs file: [ +0.002865] ------------[ cut here ]------------ [ +0.002327] kobject: '(null)' (0000000056260cfb): is not initialized, yet kobject_put() is being called. [ +0.004780] WARNING: CPU: 32 PID: 1006 at lib/kobject.c:718 kobject_put+0xaa/0x1c0 [ +0.001361] Call Trace: [ +0.001234] <TASK> [ +0.001067] kfd_remove_sysfs_node_entry+0x24a/0x2d0 [amdgpu] [ +0.003147] kfd_topology_update_sysfs+0x3d/0x750 [amdgpu] [ +0.002890] kfd_topology_add_device+0xbd7/0xc70 [amdgpu] [ +0.002844] ? lock_release+0x13c/0x2e0 [ +0.001936] ? smu_cmn_send_smc_msg_with_param+0x1e8/0x2d0 [amdgpu] [ +0.003313] ? amdgpu_dpm_get_mclk+0x54/0x60 [amdgpu] [ +0.002703] kgd2kfd_device_init.cold+0x39f/0x4ed [amdgpu] [ +0.002930] amdgpu_amdkfd_device_init+0x13d/0x1f0 [amdgpu] [ +0.002944] amdgpu_device_init.cold+0x1464/0x17b4 [amdgpu] [ +0.002970] ? pci_bus_read_config_word+0x43/0x80 [ +0.002380] amdgpu_driver_load_kms+0x15/0x100 [amdgpu] [ +0.002744] amdgpu_pci_probe+0x147/0x370 [amdgpu] [ +0.002522] local_pci_probe+0x40/0x80 [ +0.001896] work_for_cpu_fn+0x10/0x20 [ +0.001892] process_one_work+0x26e/0x5a0 [ +0.002029] worker_thread+0x1fd/0x3e0 [ +0.001890] ? process_one_work+0x5a0/0x5a0 [ +0.002115] kthread+0xea/0x110 [ +0.001618] ? kthread_complete_and_exit+0x20/0x20 [ +0.002422] ret_from_fork+0x1f/0x30 [ +0.001808] </TASK> [ +0.001103] irq event stamp: 59837 [ +0.001718] hardirqs last enabled at (59849): [<ffffffffb30fab12>] __up_console_sem+0x52/0x60 [ +0.004414] hardirqs last disabled at (59860): [<ffffffffb30faaf7>] __up_console_sem+0x37/0x60 [ +0.004414] softirqs last enabled at (59654): [<ffffffffb307d9c7>] irq_exit_rcu+0xd7/0x130 [ +0.004205] softirqs last disabled at (59649): [<ffffffffb307d9c7>] irq_exit_rcu+0xd7/0x130 [ +0.004203] ---[ end trace 0000000000000000 ]--- Fixes: 0f28cca8 ("drm/amdkfd: Extend KFD device topology to surface peer-to-peer links") Signed-off-by:
Mukul Joshi <mukul.joshi@amd.com> Reviewed-by:
-
- 20 Dec, 2022 7 commits
-
-
Tim Huang authored
MES is part of gfxoff and MES suspend and resume are skipped for S0i3. But the mes_self_test call path is still in the amdgpu_device_ip_late_init. it's should also be skipped for s0ix as no hardware re-initialization happened. Besides, mes_self_test will free the BO that triggers a lot of warning messages while in the suspend state. [ 81.656085] WARNING: CPU: 2 PID: 1550 at drivers/gpu/drm/amd/amdgpu/amdgpu_object.c:425 amdgpu_bo_free_kernel+0xfc/0x110 [amdgpu] [ 81.679435] Call Trace: [ 81.679726] <TASK> [ 81.679981] amdgpu_mes_remove_hw_queue+0x17a/0x230 [amdgpu] [ 81.680857] amdgpu_mes_self_test+0x390/0x430 [amdgpu] [ 81.681665] mes_v11_0_late_init+0x37/0x50 [amdgpu] [ 81.682423] amdgpu_device_ip_late_init+0x53/0x280 [amdgpu] [ 81.683257] amdgpu_device_resume+0xae/0x2a0 [amdgpu] [ 81.684043] amdgpu_pmops_resume+0x37/0x70 [amdgpu] [ 81.684818] pci_pm_resume+0x5c/0xa0 [ 81.685247] ? pci_pm_thaw+0x90/0x90 [ 81.685658] dpm_run_callback+0x4e/0x160 [ 81.686110] device_resume+0xad/0x210 [ 81.686529] async_resume+0x1e/0x40 [ 81.686931] async_run_entry_fn+0x33/0x120 [ 81.687405] process_one_work+0x21d/0x3f0 [ 81.687869] worker_thread+0x4a/0x3c0 [ 81.688293] ? process_one_work+0x3f0/0x3f0 [ 81.688777] kthread+0xff/0x130 [ 81.689157] ? kthread_complete_and_exit+0x20/0x20 [ 81.689707] ret_from_fork+0x22/0x30 [ 81.690118] </TASK> [ 81.690380] ---[ end trace 0000000000000000 ]--- v2: make the comment clean and use adev->in_s0ix instead of adev->suspend Signed-off-by:
Tim Huang <tim.huang@amd.com> Reviewed-by:
Mario Limonciello <mario.limonciello@amd.com> Signed-off-by:
-
Srinivasan Shanmugam authored
Fix the following checkpatch checks in amdgpu_dm.c CHECK: Prefer kernel type 'u8' over 'uint8_t' CHECK: Prefer kernel type 'u32' over 'uint32_t' CHECK: Prefer kernel type 'u64' over 'uint64_t' CHECK: Prefer kernel type 's32' over 'int32_t' Signed-off-by:
Srinivasan Shanmugam <srinivasan.shanmugam@amd.com> Reviewed-by:
Harry Wentland <harry.wentland@amd.com> Signed-off-by:
-
Evan Quan authored
For SMU 13.0.0 and 13.0.7, the output from PMFW is in percent. Driver need to convert that into correct PMW(255) based. Signed-off-by:
Evan Quan <evan.quan@amd.com> Acked-by:
-
hersen wu authored
[Why] connector hdcp properties are lost after display is unplgged from mst hub. connector is destroyed with dm_dp_mst_connector_destroy. when display is plugged back, hdcp is not desired and it wouldnt be enabled. [How] save hdcp properties into hdcp_work within amdgpu_dm_atomic_commit_tail. If the same display is plugged back with same display index, its hdcp properties will be retrieved from hdcp_work within dm_dp_mst_get_modes. Acked-by:
-
Evan Quan authored
To fit the latest PMFW and suppress the warning emerged on driver loading. Signed-off-by:
-
Evan Quan authored
Add the support for WINDOW3D profile mode as for other profile modes. Signed-off-by:
-
Alex Deucher authored
It's also part of gfxoff. Cc: stable@vger.kernel.org # 6.0, 6.1 Reviewed-by:
-
