Currently in the FSL platform all GPIO interrupts in a bank are muxed
into two GPIO lines to the GPC interrupt controller. In each GPIO bank
GPIOs 0-15 are OR'ed into one GPC interrupt controller interrupt and 16-31
are OR'ed into another. With the current code, if any of the 0-15 or
16-31 interrupts are marked as wakeup capable, all interrupts belonging
to that sub-bank (either 0-15 or 16-31) will wake up the device. This is
because interrupts are only being masked at the interrupt controller
and not at the GPIO controller.

This patch allows masking of GPIO interrupts at the GPIO controller during
suspend if they have not been labeled wakeup capable. This patch uses
preexisting IRQCHIP_MASK_ON_SUSPEND flag while initializing the GPIO
interrupts to get the desired behavior.

Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Ulises Brindis <ubrindis56@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Fix below build warning:
  CC      drivers/gpio/gpio-omap.o
drivers/gpio/gpio-omap.c: In function 'omap_gpio_irq_type':
drivers/gpio/gpio-omap.c:504:3: warning: passing argument 1 of 'spin_unlock_irqrestore' from incompatible pointer type [enabled by default]
include/linux/spinlock.h:360:29: note: expected 'struct spinlock_t *' but argument is of type 'struct raw_spinlock_t *'

Fixes: commit 4dbada2b ("gpio: omap: use raw locks for locking")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Linux 4.2-rc4

For wake from S5, we need to:
- register a reboot handler
- set wakeup capability before requesting IRQ so wakeup count is
  incremented
- mask all GPIO IRQs and clear any pending interrupts during driver
  probe to since no driver will yet be registered to handle any IRQs
  carried over from boot at that time, and it's possible that the
  booted kernel does not request the same IRQ anyway.

This means that /sys/.../power/wakeup_count is valid at boot time, and
we can properly account for S5 wakeup stats. e.g.:

  ### After waking from S5 from a GPIO key
  # cat /sys/bus/platform/drivers/brcmstb-gpio/f04172c0.gpio/power/wakeup
  enabled
  # cat /sys/bus/platform/drivers/brcmstb-gpio/f04172c0.gpio/power/wakeup_count
  1
Signed-off-by: Gregory Fong <gregory.0xf0@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Uses the gpiolib irqchip helpers.  For this to work, the irq setup
function is called once per bank instead of once per device.  Note
that all known uses of this block have a BCM7120 L2 interrupt
controller as a parent.  Supports interrupts for all GPIOs.

In the IRQ handler, we check for raised IRQs for invalid GPIOs and
warn (ratelimited) if they're encountered.

Also, several drivers (e.g. gpio-keys) allow for GPIOs to be
configured as wakeup sources, and this GPIO controller supports that
through a separate interrupt path.

The de-facto standard DT property "wakeup-source" is checked, since
that indicates whether the GPIO controller hardware can wake.  Uses
the IRQCHIP_MASK_ON_SUSPEND irq_chip flag because UPG GIO doesn't have
any of its own wakeup source configuration.

Aside regarding gpiolib irqchip helpers: It wasn't obvious (to me)
that you can have multiple chained irqchips and associated IRQ domains
for a single parent IRQ, and as long as the xlate function is written
correctly, a GPIO IRQ request end up checking the correct domain and
will get associated with the correct IRQ.  What helps make this clear
is to read
  drivers/gpio/gpiolib-of.c:
   - of_gpiochip_find_and_xlate()
   - of_get_named_gpiod_flags()
  drivers/gpio/gpiolib.c:
   - gpiochip_find()
Signed-off-by: Gregory Fong <gregory.0xf0@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

commit 926b663c
"gpiolib: allow GPIOs to be named" added the ability to
name GPIO lines by an array of names stored in the GPIO
chip. This was in 2009 and has been an ABI since. Let's
document it properly.

Cc: Daniel Silverstone <dsilvers@digital-scurf.org>
Cc: Markus Pargmann <mpa@pengutronix.de>
Cc: Johan Hovold <johan@kernel.org>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

On ETRAX FS, all pins on the first port (and only the first port) have
interrupt support.

On ARTPEC-3, all pins on all ports have interrupt support.  However,
there are only eight interrupts.  Each of the interrupts is associated
with a group of pins and for each interrupt the one pin from the group
which will trigger it can be selected.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

If the driver has specified its own irq_{request/release}_resources()
functions, don't override them.  The gpio-etraxfs driver will use this.
Signed-off-by: Rabin Vincent <rabin@rab.in>
[Added a small comment blurb]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

mpc8xxx_gpio_chip.lock needs to be a real spinlock in preempt-rt.
Especially the interrupt related functions can not be converted to a
sleeping lock.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

When an OF node has a pin range for its GPIOs, return -EPROBE_DEFER if
the pin controller isn't available.

Otherwise, the GPIO range wouldn't be set at all unless the pin
controller probed always before the GPIO chip.

With this change, the probe of the GPIO chip will be deferred and will
be retried at a later point, hopefully once the pin controller has been
registered and probed already.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

set_irq_flags is ARM specific with custom flags which have genirq
equivalents. Convert drivers to use the genirq interfaces directly, so we
can kill off set_irq_flags. The translation of flags is as follows:

IRQF_VALID -> !IRQ_NOREQUEST
IRQF_PROBE -> !IRQ_NOPROBE
IRQF_NOAUTOEN -> IRQ_NOAUTOEN

For IRQs managed by an irqdomain, the irqdomain core code handles clearing
and setting IRQ_NOREQUEST already, so there is no need to do this in
.map() functions and we can simply remove the set_irq_flags calls. Some
users also modify IRQ_NOPROBE and this has been maintained although it
is not clear that is really needed as most platforms don't use probing.
There appears to be a great deal of blind copy and paste of this code.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: linux-gpio@vger.kernel.org
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add support for the GIO block in the ARTPEC-3 SoC.  The basic
functionality is essentialy the same as the version in the ETRAX FS,
except for a different set of ports, including a read-only port.

Cc: devicetree@vger.kernel.org
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Allow chips to indicates that they are input-only and thus cannot set
the output value.  This will be used by the gpio-etraxfs driver.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

BGPIO_F_UNREADABLE_REG_SET is incorrect, since the set register _is_
readable.  What's really required is BGPIO_F_READ_OUTPUT_REG_SET:
reading the set register reads the set output value.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

R-Car Gen3's GPIO blocks are identical to Gen2's in every respect.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This patch converts gpio_bank.lock from a spin_lock into a
raw_spin_lock. The call path is to access this lock is always under a
raw_spin_lock, for instance
- __setup_irq() holds &desc->lock with irq off
  + __irq_set_trigger()
   + omap_gpio_irq_type()

- handle_level_irq() (runs with irqs off therefore raw locks)
  + mask_ack_irq()
   + omap_gpio_mask_irq()

This fixes the obvious backtrace on -RT. However the locking vs context
is not and this is not limited to -RT:
- omap_gpio_irq_type() is called with IRQ off and has an conditional
  call to pm_runtime_get_sync() which may sleep. Either it may happen or
  it may not happen but pm_runtime_get_sync() should not be called with
  irqs off.

- omap_gpio_debounce() is holding the lock with IRQs off.
  + omap2_set_gpio_debounce()
   + clk_prepare_enable()
    + clk_prepare() this one might sleep.
  The number of users of gpiod_set_debounce() / gpio_set_debounce()
  looks low but still this is not good.
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This variable is used as an iterator and initialized in the
list_for_each() loop.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The gpio controller on MPC5125 is identical to the MPC5121 register
wise, the only difference is that the lines 0..3 are input only instead
of 28..31 on MPC5121.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The gpio controllers that are handled by the mpc8xxx driver differ
slightly. Up to now some differences were handled by use of
of_device_is_compatible, others by use of struct of_device_id's data.

To make this consistent and easily extendable handle the differences at
a single place.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This variable is not modified in the driver and all functions it it
passed to don't change it either. So it can and should be marked const.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Pull perf fix from Thomas Gleixner:
 "A single fix for the intel cqm perf facility to prevent IPIs from
  interrupt context"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/x86/intel/cqm: Return cached counter value from IRQ context

Pull x86 fixes from Thomas Gleixner:
 "This update contains:

   - the manual revert of the SYSCALL32 changes which caused a
     regression

   - a fix for the MPX vma handling

   - three fixes for the ioremap 'is ram' checks.

   - PAT warning fixes

   - a trivial fix for the size calculation of TLB tracepoints

   - handle old EFI structures gracefully

  This also contains a PAT fix from Jan plus a revert thereof.  Toshi
  explained why the code is correct"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/mm/pat: Revert 'Adjust default caching mode translation tables'
  x86/asm/entry/32: Revert 'Do not use R9 in SYSCALL32' commit
  x86/mm: Fix newly introduced printk format warnings
  mm: Fix bugs in region_is_ram()
  x86/mm: Remove region_is_ram() call from ioremap
  x86/mm: Move warning from __ioremap_check_ram() to the call site
  x86/mm/pat, drivers/media/ivtv: Move the PAT warning and replace WARN() with pr_warn()
  x86/mm/pat, drivers/infiniband/ipath: Replace WARN() with pr_warn()
  x86/mm/pat: Adjust default caching mode translation tables
  x86/fpu: Disable dependent CPU features on "noxsave"
  x86/mpx: Do not set ->vm_ops on MPX VMAs
  x86/mm: Add parenthesis for TLB tracepoint size calculation
  efi: Handle memory error structures produced based on old versions of standard

Toshi explains:

"No, the default values need to be set to the fallback types,
 i.e. minimal supported mode.  For WC and WT, UC is the fallback type.

 When PAT is disabled, pat_init() does update the tables below to
 enable WT per the default BIOS setup.  However, when PAT is enabled,
 but CPU has PAT -errata, WT falls back to UC per the default values."

Revert: ca1fec58 'x86/mm/pat: Adjust default caching mode translation tables'
Requested-by: Toshi Kani <toshi.kani@hp.com>
Cc: Jan Beulich <jbeulich@suse.de>
Link: http://lkml.kernel.org/r/1437577776.3214.252.camel@hp.comSigned-off-by: Thomas Gleixner <tglx@linutronix.de>

Peter reported the following potential crash which I was able to
reproduce with his test program,

[  148.765788] ------------[ cut here ]------------
[  148.765796] WARNING: CPU: 34 PID: 2840 at kernel/smp.c:417 smp_call_function_many+0xb6/0x260()
[  148.765797] Modules linked in:
[  148.765800] CPU: 34 PID: 2840 Comm: perf Not tainted 4.2.0-rc1+ #4
[  148.765803]  ffffffff81cdc398 ffff88085f105950 ffffffff818bdfd5 0000000000000007
[  148.765805]  0000000000000000 ffff88085f105990 ffffffff810e413a 0000000000000000
[  148.765807]  ffffffff82301080 0000000000000022 ffffffff8107f640 ffffffff8107f640
[  148.765809] Call Trace:
[  148.765810]  <NMI>  [<ffffffff818bdfd5>] dump_stack+0x45/0x57
[  148.765818]  [<ffffffff810e413a>] warn_slowpath_common+0x8a/0xc0
[  148.765822]  [<ffffffff8107f640>] ? intel_cqm_stable+0x60/0x60
[  148.765824]  [<ffffffff8107f640>] ? intel_cqm_stable+0x60/0x60
[  148.765825]  [<ffffffff810e422a>] warn_slowpath_null+0x1a/0x20
[  148.765827]  [<ffffffff811613f6>] smp_call_function_many+0xb6/0x260
[  148.765829]  [<ffffffff8107f640>] ? intel_cqm_stable+0x60/0x60
[  148.765831]  [<ffffffff81161748>] on_each_cpu_mask+0x28/0x60
[  148.765832]  [<ffffffff8107f6ef>] intel_cqm_event_count+0x7f/0xe0
[  148.765836]  [<ffffffff811cdd35>] perf_output_read+0x2a5/0x400
[  148.765839]  [<ffffffff811d2e5a>] perf_output_sample+0x31a/0x590
[  148.765840]  [<ffffffff811d333d>] ? perf_prepare_sample+0x26d/0x380
[  148.765841]  [<ffffffff811d3497>] perf_event_output+0x47/0x60
[  148.765843]  [<ffffffff811d36c5>] __perf_event_overflow+0x215/0x240
[  148.765844]  [<ffffffff811d4124>] perf_event_overflow+0x14/0x20
[  148.765847]  [<ffffffff8107e7f4>] intel_pmu_handle_irq+0x1d4/0x440
[  148.765849]  [<ffffffff811d07a6>] ? __perf_event_task_sched_in+0x36/0xa0
[  148.765853]  [<ffffffff81219bad>] ? vunmap_page_range+0x19d/0x2f0
[  148.765854]  [<ffffffff81219d11>] ? unmap_kernel_range_noflush+0x11/0x20
[  148.765859]  [<ffffffff814ce6fe>] ? ghes_copy_tofrom_phys+0x11e/0x2a0
[  148.765863]  [<ffffffff8109e5db>] ? native_apic_msr_write+0x2b/0x30
[  148.765865]  [<ffffffff8109e44d>] ? x2apic_send_IPI_self+0x1d/0x20
[  148.765869]  [<ffffffff81065135>] ? arch_irq_work_raise+0x35/0x40
[  148.765872]  [<ffffffff811c8d86>] ? irq_work_queue+0x66/0x80
[  148.765875]  [<ffffffff81075306>] perf_event_nmi_handler+0x26/0x40
[  148.765877]  [<ffffffff81063ed9>] nmi_handle+0x79/0x100
[  148.765879]  [<ffffffff81064422>] default_do_nmi+0x42/0x100
[  148.765880]  [<ffffffff81064563>] do_nmi+0x83/0xb0
[  148.765884]  [<ffffffff818c7c0f>] end_repeat_nmi+0x1e/0x2e
[  148.765886]  [<ffffffff811d07a6>] ? __perf_event_task_sched_in+0x36/0xa0
[  148.765888]  [<ffffffff811d07a6>] ? __perf_event_task_sched_in+0x36/0xa0
[  148.765890]  [<ffffffff811d07a6>] ? __perf_event_task_sched_in+0x36/0xa0
[  148.765891]  <<EOE>>  [<ffffffff8110ab66>] finish_task_switch+0x156/0x210
[  148.765898]  [<ffffffff818c1671>] __schedule+0x341/0x920
[  148.765899]  [<ffffffff818c1c87>] schedule+0x37/0x80
[  148.765903]  [<ffffffff810ae1af>] ? do_page_fault+0x2f/0x80
[  148.765905]  [<ffffffff818c1f4a>] schedule_user+0x1a/0x50
[  148.765907]  [<ffffffff818c666c>] retint_careful+0x14/0x32
[  148.765908] ---[ end trace e33ff2be78e14901 ]---

The CQM task events are not safe to be called from within interrupt
context because they require performing an IPI to read the counter value
on all sockets. And performing IPIs from within IRQ context is a
"no-no".

Make do with the last read counter value currently event in
event->count when we're invoked in this context.
Reported-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vikas Shivappa <vikas.shivappa@intel.com>
Cc: Kanaka Juvva <kanaka.d.juvva@intel.com>
Cc: Will Auld <will.auld@intel.com>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/1437490509-15373-1-git-send-email-matt@codeblueprint.co.ukSigned-off-by: Thomas Gleixner <tglx@linutronix.de>

Pull USB fixes from Greg KH:
 "Here's a few USB and PHY fixes for 4.2-rc4.

  Nothing major, the shortlog has the full details.

  All of these have been in linux-next successfully"

* tag 'usb-4.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (21 commits)
  USB: OHCI: fix bad #define in ohci-tmio.c
  cdc-acm: Destroy acm_minors IDR on module exit
  usb-storage: Add ignore-device quirk for gm12u320 based usb mini projectors
  usb-storage: ignore ZTE MF 823 card reader in mode 0x1225
  USB: OHCI: Fix race between ED unlink and URB submission
  usb: core: lpm: set lpm_capable for root hub device
  xhci: do not report PLC when link is in internal resume state
  xhci: prevent bus_suspend if SS port resuming in phase 1
  xhci: report U3 when link is in resume state
  xhci: Calculate old endpoints correctly on device reset
  usb: xhci: Bugfix for NULL pointer deference in xhci_endpoint_init() function
  xhci: Workaround to get D3 working in Intel xHCI
  xhci: call BIOS workaround to enable runtime suspend on Intel Braswell
  usb: dwc3: Reset the transfer resource index on SET_INTERFACE
  usb: gadget: udc: core: Fix argument of dma_map_single for IOMMU
  usb: gadget: mv_udc_core: fix phy_regs I/O memory leak
  usb: ulpi: ulpi_init should be executed in subsys_initcall
  phy: berlin-usb: fix divider for BG2
  phy: berlin-usb: fix divider for BG2CD
  phy/pxa: add HAS_IOMEM dependency
  ...

Pull tty/serial driver fixes from Greg KH:
 "Here are a number of small serial and tty fixes for reported issues.

  All have been in linux-next successfully"

* tag 'tty-4.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  tty: vt: Fix !TASK_RUNNING diagnostic warning from paste_selection()
  serial: core: Fix crashes while echoing when closing
  m32r: Add ioreadXX/iowriteXX big-endian mmio accessors
  Revert "serial: imx: initialized DMA w/o HW flow enabled"
  sc16is7xx: fix FIFO address of secondary UART
  sc16is7xx: fix Kconfig dependencies
  serial: etraxfs-uart: Fix release etraxfs_uart_ports
  tty/vt: Fix the memory leak in visual_init
  serial: amba-pl011: Fix devm_ioremap_resource return value check
  n_tty: signal and flush atomically

Pull staging driver fixes from Greg KH:
 "Here are a number of iio and staging driver fixes for reported issues
  for 4.2-rc4.

  All have been in linux-next for a while with no problems"

* tag 'staging-4.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (34 commits)
  iio:light:stk3310: make endianness independent of host
  iio:light:stk3310: move device register to end of probe
  iio: mma8452: use iio event type IIO_EV_TYPE_MAG
  iio: mcp320x: Fix NULL pointer dereference
  iio: adc: vf610: fix the adc register read fail issue
  iio: mlx96014: Replace offset sign
  iio: magnetometer: mmc35240: fix SET/RESET sequence
  iio: magnetometer: mmc35240: Fix SET/RESET mask
  iio: magnetometer: mmc35240: Fix crash in pm suspend
  iio:magnetometer:bmc150_magn: output intended variable
  iio:magnetometer:bmc150_magn: add regmap dependency
  staging: vt6656: check ieee80211_bss_conf bssid not NULL
  staging: vt6655: check ieee80211_bss_conf bssid not NULL
  iio: tmp006: Check channel info on write
  iio: sx9500: Add missing init in sx9500_buffer_pre{en,dis}able()
  iio:light:ltr501: fix regmap dependency
  iio:light:ltr501: fix variable in ltr501_init
  iio: sx9500: fix bug in compensation code
  iio: sx9500: rework error handling of raw readings
  iio: magnetometer: mmc35240: fix available sampling frequencies
  ...

Pull char/misc driver fixes from Greg KH:
 "Here are some char and misc driver fixes for reported issues.

  One parport patch is reverted as it was incorrect, thanks to testing
  by the 0-day bot"

* tag 'char-misc-4.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  parport: Revert "parport: fix memory leak"
  mei: prevent unloading mei hw modules while the device is opened.
  misc: mic: scif bug fix for vmalloc_to_page crash
  parport: fix freeing freed memory
  parport: fix memory leak
  parport: fix error handling

This reverts commit 23c40591 ("parport: fix memory leak")

par_dev->state was already being removed in parport_unregister_device().
Reported-by: Ying Huang <ying.huang@intel.com>
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'trace-v4.2-rc2-fix3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace

Pull ftrace fix from Steven Rostedt:
 "Back in 3.16 the ftrace code was redesigned and cleaned up to remove
  the double iteration list (one for registered ftrace ops, and one for
  registered "global" ops), to just use one list.  That simplified the
  code but also broke the function tracing filtering on pid.

  This updates the code to handle the filtering again with the new
  logic"

* tag 'trace-v4.2-rc2-fix3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  ftrace: Fix breakage of set_ftrace_pid

Pull libnvdimm fix from Dan Williams:
 "A minor fix for the libnvdimm subsystem.

  This is not critical.  The problem can be worked around in userspace
  by putting the namespace temporarily into raw mode
  (ndctl_namespace_set_raw_mode() from libndctl), but that is awkward
  for management utilities.

* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/nvdimm:
  libnvdimm: fix namespace seed creation

Pull md fixes from Neil Brown:
 "Some md fixes for 4.2

  Several are tagged for -stable.
  A few aren't because they are not very, serious or because they are in
  the 'experimental' cluster code"

* tag 'md/4.2-fixes' of git://neil.brown.name/md:
  md/raid5: clear R5_NeedReplace when no longer needed.
  Fix read-balancing during node failure
  md-cluster: fix bitmap sub-offset in bitmap_read_sb
  md: Return error if request_module fails and returns positive value
  md: Skip cluster setup in case of error while reading bitmap
  md/raid1: fix test for 'was read error from last working device'.
  md: Skip cluster setup for dm-raid
  md: flush ->event_work before stopping array.
  md/raid10: always set reshape_safe when initializing reshape_position.
  md/raid5: avoid races when changing cache size.

Pull MTD fixes from Brian Norris:
 "Two trivial updates.  I meant to send these much earlier, but I've
  been preoccupied.

   - Add MAINTAINERS entry for diskonchip g3 driver

   - Fix an overlooked conflict in bitfield value assignments

  The latter update is a bit overdue, but there's no reason to wait any
  longer"

* tag 'for-linus-20150724' of git://git.infradead.org/linux-mtd:
  mtd: nand: Fix NAND_USE_BOUNCE_BUFFER flag conflict
  MAINTAINERS: mtd: docg3: add docg3 maintainer

A new BLK namespace "seed" device is created whenever the current seed
is successfully probed.  However, if that namespace is assigned to a BTT
it may never directly experience a successful probe as it is a
subordinate device to a BTT configuration.

The effect of the current code is that no new namespaces can be
instantiated, after the seed namespace, to consume available BLK DPA
capacity.  Fix this by treating a successful BTT probe event as a
successful probe event for the backing namespace.
Reported-by: Nicholas Moulin <nicholas.w.moulin@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

Pull block fixes from Jens Axboe:
 "Four smaller fixes for the current series.  This contains:

   - A fix for clones of discard bio's, that can cause data corruption.
     From Martin.

   - A fix for null_blk, where in certain queue modes it could access a
     request after it had been freed.  From Mike Krinkin.

   - An error handling leak fix for blkcg, from Tejun.

   - Also from Tejun, export of the functions that a file system needs
     to implement cgroup writeback support"

* 'for-linus' of git://git.kernel.dk/linux-block:
  block: Do a full clone when splitting discard bios
  block: export bio_associate_*() and wbc_account_io()
  blkcg: fix gendisk reference leak in blkg_conf_prep()
  null_blk: fix use-after-free problem

Pull libata fixes from Tejun Heo:
 "A couple important fixes.

   - A block layer change which removed restriction on max transfer size
     led to silent data corruption on some devices.  A new quirk is
     added to restore the old size limit for the reported device.  If it
     gets reported on more devices, we might have to consider restoring
     the restriction for ATA devices by default.

   - There finally is a SSD which is confirmed to cause data corruption
     on TRIM regardless of which flavor is used.  A new quirk is added
     and the device is blacklisted

   - Other device-specific workarounds"

* 'for-4.2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
  libata: Do not blacklist M510DC
  libata: increase the timeout when setting transfer mode
  libata: add ATA_HORKAGE_MAX_SEC_1024 to revert back to previous max_sectors limit
  libata: force disable trim for SuperSSpeed S238
  libata: add ATA_HORKAGE_NOTRIM
  libata: add ATA_HORKAGE_BROKEN_FPDMA_AA quirk for HP 250GB SATA disk VB0250EAVER
  ata: pmp: add quirk for Marvell 4140 SATA PMP

Pull MMC fixes from Ulf Hansson:
 "Here are some mmc fixes intended for v4.2 rc4.

  Note, most of the changes are for the sdhci-esdhc-imx controller,
  which also required us to modify some related DTS files.  Those
  changes have been acked by the SoC maintainer.

  MMC core:
   - Fix a reference inbalance issue for power_ro_lock_show() sysfs handler

  MMC host:
   - omap_hsmmc: Fix IRQ errorhandling for CD, DTO, and CRC
   - sdhci: Prevent a kernel panic while using DMA
   - mtk-sd: Let it depend on HAS_DMA to prevent build errors
   - sdhci-esdhc: Make 8BIT bus work
   - sdhci-esdhc-imx: Fix some regressions for DT based platforms
   - sdhci-pxav3: Fix a regression for DT based platforms"

* tag 'mmc-4.2-rc3' of git://git.linaro.org/people/ulf.hansson/mmc:
  mmc: sdhci-pxav3: fix platform_data is not initialized
  dts: mmc: fsl-imx-esdhc: remove fsl,cd-controller support
  mmc: sdhci-esdhc-imx: clear f_max in boarddata
  mmc: sdhci-esdhc-imx: remove duplicated dts parsing
  mmc: sdhci: make max-frequency property in device tree work
  mmc: sdhci-esdhc-imx: move all non dt probe code into one function
  mmc: sdhci-esdhc-imx: fix cd regression for dt platform
  dts: imx7: fix sd card gpio polarity specified in device tree
  dts: imx25: fix sd card gpio polarity specified in device tree
  dts: imx6: fix sd card gpio polarity specified in device tree
  dts: imx53: fix sd card gpio polarity specified in device tree
  dts: imx51: fix sd card gpio polarity specified in device tree
  mmc: sdhci-esdhc: Make 8BIT bus work
  mmc: block: Add missing mmc_blk_put() in power_ro_lock_show()
  mmc: MMC_MTK should depend on HAS_DMA
  mmc: sdhci check parameters before call dma_free_coherent
  mmc: omap_hsmmc: Handle BADA, DEB and CEB interrupts
  mmc: omap_hsmmc: Fix DTO and DCRC handling

Pull input fixes from Dmitry Torokhov:
 "A fix for the warnings/oops when handling HID devices with "unnamed"
  LEDs and couple of other driver fixups""

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: goodix - fix touch coordinates on WinBook TW100 and TW700
  Input: LEDs - skip unnamed LEDs
  Input: usbtouchscreen - avoid unresponsive TSC-30 touch screen
  Input: elantech - force resolution of 31 u/mm
  Input: zforce - don't overwrite the stack