Commit b0e214d2 ("netfilter: keep conntrack reference until
IPsecv6 policy checks are done") is a direct copy of the old
commit b59c2701 ("[NETFILTER]: Keep conntrack reference until
IPsec policy checks are done") but for IPv6.  However, it also
copies a bug that this old commit had.  That is: when the third
packet of 3WHS connection establishment contains payload, it is
added into socket receive queue without the XFRM check and the
drop of connection tracking context.

That leads to nf_conntrack module being impossible to unload as
it waits for all the conntrack references to be dropped while
the packet release is deferred in per-cpu cache indefinitely, if
not consumed by the application.

The issue for IPv4 was fixed in commit 6f0012e3 ("tcp: add a
missing nf_reset_ct() in 3WHS handling") by adding a missing XFRM
check and correctly dropping the conntrack context.  However, the
issue was introduced to IPv6 code afterwards.  Fixing it the
same way for IPv6 now.

Fixes: b0e214d2 ("netfilter: keep conntrack reference until IPsecv6 policy checks are done")
Link: https://lore.kernel.org/netdev/d589a999-d4dd-2768-b2d5-89dec64a4a42@ovn.org/Signed-off-by: Ilya Maximets <i.maximets@ovn.org>
Acked-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20230922210530.2045146-1-i.maximets@ovn.orgSigned-off-by: Paolo Abeni <pabeni@redhat.com>

After deleting an interface address in fib_del_ifaddr(), the function
scans the fib_info list for stray entries and calls fib_flush() and
fib_table_flush(). Then the stray entries will be deleted silently and no
RTM_DELROUTE notification will be sent.

This lack of notification can make routing daemons, or monitor like
`ip monitor route` miss the routing changes. e.g.

+ ip link add dummy1 type dummy
+ ip link add dummy2 type dummy
+ ip link set dummy1 up
+ ip link set dummy2 up
+ ip addr add 192.168.5.5/24 dev dummy1
+ ip route add 7.7.7.0/24 dev dummy2 src 192.168.5.5
+ ip -4 route
7.7.7.0/24 dev dummy2 scope link src 192.168.5.5
192.168.5.0/24 dev dummy1 proto kernel scope link src 192.168.5.5
+ ip monitor route
+ ip addr del 192.168.5.5/24 dev dummy1
Deleted 192.168.5.0/24 dev dummy1 proto kernel scope link src 192.168.5.5
Deleted broadcast 192.168.5.255 dev dummy1 table local proto kernel scope link src 192.168.5.5
Deleted local 192.168.5.5 dev dummy1 table local proto kernel scope host src 192.168.5.5

As Ido reminded, fib_table_flush() isn't only called when an address is
deleted, but also when an interface is deleted or put down. The lack of
notification in these cases is deliberate. And commit 7c6bb7d2
("net/ipv6: Add knob to skip DELROUTE message on device down") introduced
a sysctl to make IPv6 behave like IPv4 in this regard. So we can't send
the route delete notify blindly in fib_table_flush().

To fix this issue, let's add a new flag in "struct fib_info" to track the
deleted prefer source address routes, and only send notify for them.

After update:
+ ip monitor route
+ ip addr del 192.168.5.5/24 dev dummy1
Deleted 192.168.5.0/24 dev dummy1 proto kernel scope link src 192.168.5.5
Deleted broadcast 192.168.5.255 dev dummy1 table local proto kernel scope link src 192.168.5.5
Deleted local 192.168.5.5 dev dummy1 table local proto kernel scope host src 192.168.5.5
Deleted 7.7.7.0/24 dev dummy2 scope link src 192.168.5.5
Suggested-by: Thomas Haller <thaller@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20230922075508.848925-1-liuhangbin@gmail.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

In the pathological case of building sky2 with 16k PAGE_SIZE, the
frag_addr[] array would never be used, so the original code was correct
that size should be 0. But the compiler now gets upset with 0 size arrays
in places where it hasn't eliminated the code that might access such an
array (it can't figure out that in this case an rx skb with fragments
would never be created). To keep the compiler happy, make sure there is
at least 1 frag_addr in struct rx_ring_info:

   In file included from include/linux/skbuff.h:28,
                    from include/net/net_namespace.h:43,
                    from include/linux/netdevice.h:38,
                    from drivers/net/ethernet/marvell/sky2.c:18:
   drivers/net/ethernet/marvell/sky2.c: In function 'sky2_rx_unmap_skb':
   include/linux/dma-mapping.h:416:36: warning: array subscript i is outside array bounds of 'dma_addr_t[0]' {aka 'long long unsigned int[]'} [-Warray-bounds=]
     416 | #define dma_unmap_page(d, a, s, r) dma_unmap_page_attrs(d, a, s, r, 0)
         |                                    ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
   drivers/net/ethernet/marvell/sky2.c:1257:17: note: in expansion of macro 'dma_unmap_page'
    1257 |                 dma_unmap_page(&pdev->dev, re->frag_addr[i],
         |                 ^~~~~~~~~~~~~~
   In file included from drivers/net/ethernet/marvell/sky2.c:41:
   drivers/net/ethernet/marvell/sky2.h:2198:25: note: while referencing 'frag_addr'
    2198 |         dma_addr_t      frag_addr[ETH_JUMBO_MTU >> PAGE_SHIFT];
         |                         ^~~~~~~~~

With CONFIG_PAGE_SIZE_16KB=y, PAGE_SHIFT == 14, so:

  #define ETH_JUMBO_MTU   9000

causes "ETH_JUMBO_MTU >> PAGE_SHIFT" to be 0. Use "?: 1" to solve this build warning.

Cc: Mirko Lindner <mlindner@marvell.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: netdev@vger.kernel.org
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202309191958.UBw1cjXk-lkp@intel.com/Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since commit 23d775f1 ("net: dsa: mv88e6xxx: Wait for EEPROM done
before HW reset") the following error is seen on a imx8mn board with
a 88E6320 switch:

mv88e6085 30be0000.ethernet-1:00: Timeout waiting for EEPROM done

This board does not have an EEPROM attached to the switch though.

This problem is well explained by Andrew Lunn:

"If there is an EEPROM, and the EEPROM contains a lot of data, it could
be that when we perform a hardware reset towards the end of probe, it
interrupts an I2C bus transaction, leaving the I2C bus in a bad state,
and future reads of the EEPROM do not work.

The work around for this was to poll the EEInt status and wait for it
to go true before performing the hardware reset.

However, we have discovered that for some boards which do not have an
EEPROM, EEInt never indicates complete. As a result,
mv88e6xxx_g1_wait_eeprom_done() spins for a second and then prints a
warning.

We probably need a different solution than calling
mv88e6xxx_g1_wait_eeprom_done(). The datasheet for 6352 documents the
EEPROM Command register:

bit 15 is:

  EEPROM Unit Busy. This bit must be set to a one to start an EEPROM
  operation (see EEOp below). Only one EEPROM operation can be
  executing at one time so this bit must be zero before setting it to
  a one.  When the requested EEPROM operation completes this bit will
  automatically be cleared to a zero. The transition of this bit from
  a one to a zero can be used to generate an interrupt (the EEInt in
  Global 1, offset 0x00).

and more interesting is bit 11:

  Register Loader Running. This bit is set to one whenever the
  register loader is busy executing instructions contained in the
  EEPROM."

Change to using mv88e6xxx_g2_eeprom_wait() to fix the timeout error
when the EEPROM chip is not present.

Fixes: 23d775f1 ("net: dsa: mv88e6xxx: Wait for EEPROM done before HW reset")
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

When device_add() fails, ptp_ocp_dev_release() will be called
after put_device(). Therefore, it seems that the
ptp_ocp_dev_release() before put_device() is redundant.

Fixes: 773bda96 ("ptp: ocp: Expose various resources on the timecard.")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Reviewed-by: Vadim Feodrenko <vadim.fedorenko@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>

Similar to the change in commit 0bdf3993("net: Avoid address
overwrite in kernel_connect"), BPF hooks run on bind may rewrite the
address passed to kernel_bind(). This change

1) Makes a copy of the bind address in kernel_bind() to insulate
   callers.
2) Replaces direct calls to sock->ops->bind() in net with kernel_bind()

Link: https://lore.kernel.org/netdev/20230912013332.2048422-1-jrife@google.com/
Fixes: 4fbac77d ("bpf: Hooks for sys_bind")
Cc: stable@vger.kernel.org
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jordan Rife <jrife@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Callers of sock_sendmsg(), and similarly kernel_sendmsg(), in kernel
space may observe their value of msg_name change in cases where BPF
sendmsg hooks rewrite the send address. This has been confirmed to break
NFS mounts running in UDP mode and has the potential to break other
systems.

This patch:

1) Creates a new function called __sock_sendmsg() with same logic as the
   old sock_sendmsg() function.
2) Replaces calls to sock_sendmsg() made by __sys_sendto() and
   __sys_sendmsg() with __sock_sendmsg() to avoid an unnecessary copy,
   as these system calls are already protected.
3) Modifies sock_sendmsg() so that it makes a copy of msg_name if
   present before passing it down the stack to insulate callers from
   changes to the send address.

Link: https://lore.kernel.org/netdev/20230912013332.2048422-1-jrife@google.com/
Fixes: 1cedee13 ("bpf: Hooks for sys_sendmsg")
Cc: stable@vger.kernel.org
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jordan Rife <jrife@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit 0bdf3993 ("net: Avoid address overwrite in kernel_connect")
ensured that kernel_connect() will not overwrite the address parameter
in cases where BPF connect hooks perform an address rewrite. This change
replaces direct calls to sock->ops->connect() in net with kernel_connect()
to make these call safe.

Link: https://lore.kernel.org/netdev/20230912013332.2048422-1-jrife@google.com/
Fixes: d74bad4e ("bpf: Hooks for sys_connect")
Cc: stable@vger.kernel.org
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jordan Rife <jrife@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Including the transhdrlen in length is a problem when the packet is
partially filled (e.g. something like send(MSG_MORE) happened previously)
when appending to an IPv4 or IPv6 packet as we don't want to repeat the
transport header or account for it twice.  This can happen under some
circumstances, such as splicing into an L2TP socket.

The symptom observed is a warning in __ip6_append_data():

    WARNING: CPU: 1 PID: 5042 at net/ipv6/ip6_output.c:1800 __ip6_append_data.isra.0+0x1be8/0x47f0 net/ipv6/ip6_output.c:1800

that occurs when MSG_SPLICE_PAGES is used to append more data to an already
partially occupied skbuff.  The warning occurs when 'copy' is larger than
the amount of data in the message iterator.  This is because the requested
length includes the transport header length when it shouldn't.  This can be
triggered by, for example:

        sfd = socket(AF_INET6, SOCK_DGRAM, IPPROTO_L2TP);
        bind(sfd, ...); // ::1
        connect(sfd, ...); // ::1 port 7
        send(sfd, buffer, 4100, MSG_MORE);
        sendfile(sfd, dfd, NULL, 1024);

Fix this by only adding transhdrlen into the length if the write queue is
empty in l2tp_ip6_sendmsg(), analogously to how UDP does things.

l2tp_ip_sendmsg() looks like it won't suffer from this problem as it builds
the UDP packet itself.

Fixes: a32e0eec ("l2tp: introduce L2TPv3 IP encapsulation support for IPv6")
Reported-by: syzbot+62cbf263225ae13ff153@syzkaller.appspotmail.com
Link: https://lore.kernel.org/r/0000000000001c12b30605378ce8@google.com/Suggested-by: Willem de Bruijn <willemdebruijn.kernel@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Eric Dumazet <edumazet@google.com>
cc: Willem de Bruijn <willemdebruijn.kernel@gmail.com>
cc: "David S. Miller" <davem@davemloft.net>
cc: David Ahern <dsahern@kernel.org>
cc: Paolo Abeni <pabeni@redhat.com>
cc: Jakub Kicinski <kuba@kernel.org>
cc: netdev@vger.kernel.org
cc: bpf@vger.kernel.org
cc: syzkaller-bugs@googlegroups.com
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

n->output field can be read locklessly, while a writer
might change the pointer concurrently.

Add missing annotations to prevent load-store tearing.

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

While looking at a related syzbot report involving neigh_periodic_work(),
I found that I forgot to add an annotation when deleting an
RCU protected item from a list.

Readers use rcu_deference(*np), we need to use either
rcu_assign_pointer() or WRITE_ONCE() on writer side
to prevent store tearing.

I use rcu_assign_pointer() to have lockdep support,
this was the choice made in neigh_flush_dev().

Fixes: 767e97e1 ("neigh: RCU conversion of struct neighbour")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

bluetooth pull request for net:

 - Fix handling of HCI_QUIRK_STRICT_DUPLICATE_FILTER
 - Fix handling of listen for ISO unicast
 - Fix build warnings
 - Fix leaking content of local_codecs
 - Add shutdown function for QCA6174
 - Delete unused hci_req_prepare_suspend() declaration
 - Fix hci_link_tx_to RCU lock usage
 - Avoid redundant authentication
Signed-off-by: David S. Miller <davem@davemloft.net>

The second parameter of stmmac_pltfr_init() needs the pointer of
"struct plat_stmmacenet_data". So, correct the parameter typo when calling the
function.

Otherwise, it may cause this alignment exception when doing suspend/resume.
[   49.067201] CPU1 is up
[   49.135258] Internal error: SP/PC alignment exception: 000000008a000000 [#1] PREEMPT SMP
[   49.143346] Modules linked in: soc_imx9 crct10dif_ce polyval_ce nvmem_imx_ocotp_fsb_s400 polyval_generic layerscape_edac_mod snd_soc_fsl_asoc_card snd_soc_imx_audmux snd_soc_imx_card snd_soc_wm8962 el_enclave snd_soc_fsl_micfil rtc_pcf2127 rtc_pcf2131 flexcan can_dev snd_soc_fsl_xcvr snd_soc_fsl_sai imx8_media_dev(C) snd_soc_fsl_utils fuse
[   49.173393] CPU: 0 PID: 565 Comm: sh Tainted: G         C         6.5.0-rc4-next-20230804-05047-g5781a6249dae #677
[   49.183721] Hardware name: NXP i.MX93 11X11 EVK board (DT)
[   49.189190] pstate: 60400009 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[   49.196140] pc : 0x80800052
[   49.198931] lr : stmmac_pltfr_resume+0x34/0x50
[   49.203368] sp : ffff800082f8bab0
[   49.206670] x29: ffff800082f8bab0 x28: ffff0000047d0ec0 x27: ffff80008186c170
[   49.213794] x26: 0000000b5e4ff1ba x25: ffff800081e5fa74 x24: 0000000000000010
[   49.220918] x23: ffff800081fe0000 x22: 0000000000000000 x21: 0000000000000000
[   49.228042] x20: ffff0000001b4010 x19: ffff0000001b4010 x18: 0000000000000006
[   49.235166] x17: ffff7ffffe007000 x16: ffff800080000000 x15: 0000000000000000
[   49.242290] x14: 00000000000000fc x13: 0000000000000000 x12: 0000000000000000
[   49.249414] x11: 0000000000000001 x10: 0000000000000a60 x9 : ffff800082f8b8c0
[   49.256538] x8 : 0000000000000008 x7 : 0000000000000001 x6 : 000000005f54a200
[   49.263662] x5 : 0000000001000000 x4 : ffff800081b93680 x3 : ffff800081519be0
[   49.270786] x2 : 0000000080800052 x1 : 0000000000000000 x0 : ffff0000001b4000
[   49.277911] Call trace:
[   49.280346]  0x80800052
[   49.282781]  platform_pm_resume+0x2c/0x68
[   49.286785]  dpm_run_callback.constprop.0+0x74/0x134
[   49.291742]  device_resume+0x88/0x194
[   49.295391]  dpm_resume+0x10c/0x230
[   49.298866]  dpm_resume_end+0x18/0x30
[   49.302515]  suspend_devices_and_enter+0x2b8/0x624
[   49.307299]  pm_suspend+0x1fc/0x348
[   49.310774]  state_store+0x80/0x104
[   49.314258]  kobj_attr_store+0x18/0x2c
[   49.318002]  sysfs_kf_write+0x44/0x54
[   49.321659]  kernfs_fop_write_iter+0x120/0x1ec
[   49.326088]  vfs_write+0x1bc/0x300
[   49.329485]  ksys_write+0x70/0x104
[   49.332874]  __arm64_sys_write+0x1c/0x28
[   49.336783]  invoke_syscall+0x48/0x114
[   49.340527]  el0_svc_common.constprop.0+0xc4/0xe4
[   49.345224]  do_el0_svc+0x38/0x98
[   49.348526]  el0_svc+0x2c/0x84
[   49.351568]  el0t_64_sync_handler+0x100/0x12c
[   49.355910]  el0t_64_sync+0x190/0x194
[   49.359567] Code: ???????? ???????? ???????? ???????? (????????)
[   49.365644] ---[ end trace 0000000000000000 ]---

Fixes: 97117eb5 ("net: stmmac: platform: provide stmmac_pltfr_init()")
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the PF and VF drivers both support flexible rx descriptors and have
negotiated the VIRTCHNL_VF_OFFLOAD_RX_FLEX_DESC capability, the VF driver
queries the PF for the list of supported descriptor formats
(VIRTCHNL_OP_GET_SUPPORTED_RXDIDS). The PF driver is supposed to set the
supported_rxdids bits that correspond to the descriptor formats the
firmware implements. The legacy 32-byte rx desc format is always
supported, even though it is not expressed in GLFLXP_RXDID_FLAGS.

The ice driver does not advertise the legacy 32-byte rx desc support,
which leads to this failure to bring up the VF using the Intel
out-of-tree iavf driver:
 iavf 0000:41:01.0: PF does not list support for default Rx descriptor format
 ...
 iavf 0000:41:01.0: PF returned error -5 (VIRTCHNL_STATUS_ERR_PARAM) to our request 6

The in-tree iavf driver does not expose this bug, because it does not
yet implement VIRTCHNL_VF_OFFLOAD_RX_FLEX_DESC.

The ice driver must always set the ICE_RXDID_LEGACY_1 bit in
supported_rxdids. The Intel out-of-tree ice driver and the ice driver in
DPDK both do this.

I copied this piece of the code and the comment text from the Intel
out-of-tree driver.

Fixes: e753df8f ("ice: Add support Flex RXD")
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Link: https://lore.kernel.org/r/20230920115439.61172-1-mschmidt@redhat.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Process the result of hdlc_open() and call uhdlc_close()
in case of an error. It is necessary to pass the error
code up the control flow, similar to a possible
error in request_irq().
Also add a hdlc_close() call to the uhdlc_close()
because the comment to hdlc_close() says it must be called
by the hardware driver when the HDLC device is being closed

Found by Linux Verification Center (linuxtesting.org) with SVACE.

Fixes: c19b6d24 ("drivers/net: support hdlc function for QE-UCC")
Signed-off-by: Alexandra Diupina <adiupina@astralinux.ru>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from Paolo Abeni:
 "Including fixes from netfilter and bpf.

  Current release - regressions:

   - bpf: adjust size_index according to the value of KMALLOC_MIN_SIZE

   - netfilter: fix entries val in rule reset audit log

   - eth: stmmac: fix incorrect rxq|txq_stats reference

  Previous releases - regressions:

   - ipv4: fix null-deref in ipv4_link_failure

   - netfilter:
      - fix several GC related issues
      - fix race between IPSET_CMD_CREATE and IPSET_CMD_SWAP

   - eth: team: fix null-ptr-deref when team device type is changed

   - eth: i40e: fix VF VLAN offloading when port VLAN is configured

   - eth: ionic: fix 16bit math issue when PAGE_SIZE >= 64KB

  Previous releases - always broken:

   - core: fix ETH_P_1588 flow dissector

   - mptcp: fix several connection hang-up conditions

   - bpf:
      - avoid deadlock when using queue and stack maps from NMI
      - add override check to kprobe multi link attach

   - hsr: properly parse HSRv1 supervisor frames.

   - eth: igc: fix infinite initialization loop with early XDP redirect

   - eth: octeon_ep: fix tx dma unmap len values in SG

   - eth: hns3: fix GRE checksum offload issue"

* tag 'net-6.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (87 commits)
  sfc: handle error pointers returned by rhashtable_lookup_get_insert_fast()
  igc: Expose tx-usecs coalesce setting to user
  octeontx2-pf: Do xdp_do_flush() after redirects.
  bnxt_en: Flush XDP for bnxt_poll_nitroa0()'s NAPI
  net: ena: Flush XDP packets on error.
  net/handshake: Fix memory leak in __sock_create() and sock_alloc_file()
  net: hinic: Fix warning-hinic_set_vlan_fliter() warn: variable dereferenced before check 'hwdev'
  netfilter: ipset: Fix race between IPSET_CMD_CREATE and IPSET_CMD_SWAP
  netfilter: nf_tables: fix memleak when more than 255 elements expired
  netfilter: nf_tables: disable toggling dormant table state more than once
  vxlan: Add missing entries to vxlan_get_size()
  net: rds: Fix possible NULL-pointer dereference
  team: fix null-ptr-deref when team device type is changed
  net: bridge: use DEV_STATS_INC()
  net: hns3: add 5ms delay before clear firmware reset irq source
  net: hns3: fix fail to delete tc flower rules during reset issue
  net: hns3: only enable unicast promisc when mac table full
  net: hns3: fix GRE checksum offload issue
  net: hns3: add cmdq check for vf periodic service task
  net: stmmac: fix incorrect rxq|txq_stats reference
  ...

Pull finegrained timestamp reverts from Christian Brauner:
 "Earlier this week we sent a few minor fixes for the multi-grained
  timestamp work in [1]. While we were polishing those up after Linus
  realized that there might be a nicer way to fix them we received a
  regression report in [2] that fine grained timestamps break gnulib
  tests and thus possibly other tools.

  The kernel will elide fine-grain timestamp updates when no one is
  actively querying for them to avoid performance impacts. So a sequence
  like write(f1) stat(f2) write(f2) stat(f2) write(f1) stat(f1) may
  result in timestamp f1 to be older than the final f2 timestamp even
  though f1 was last written too but the second write didn't update the
  timestamp.

  Such plotholes can lead to subtle bugs when programs compare
  timestamps. For example, the nap() function in [2] will estimate that
  it needs to wait one ns on a fine-grain timestamp enabled filesytem
  between subsequent calls to observe a timestamp change. But in general
  we don't update timestamps with more than one jiffie if we think that
  no one is actively querying for fine-grain timestamps to avoid
  performance impacts.

  While discussing various fixes the decision was to go back to the
  drawing board and ultimately to explore a solution that involves only
  exposing such fine-grained timestamps to nfs internally and never to
  userspace.

  As there are multiple solutions discussed the honest thing to do here
  is not to fix this up or disable it but to cleanly revert. The general
  infrastructure will probably come back but there is no reason to keep
  this code in mainline.

  The general changes to timestamp handling are valid and a good cleanup
  that will stay. The revert is fully bisectable"

Link: https://lore.kernel.org/all/20230918-hirte-neuzugang-4c2324e7bae3@brauner [1]
Link: https://lore.kernel.org/all/bf0524debb976627693e12ad23690094e4514303.camel@linuxfromscratch.org [2]

* tag 'v6.6-rc3.vfs.ctime.revert' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs:
  Revert "fs: add infrastructure for multigrain timestamps"
  Revert "btrfs: convert to multigrain timestamps"
  Revert "ext4: switch to multigrain timestamps"
  Revert "xfs: switch to multigrain timestamps"
  Revert "tmpfs: add support for multigrain timestamps"

Pull powerpc fixes from Michael Ellerman:

 - A fix for breakpoint handling which was using get_user() while atomic

 - Fix the Power10 HASHCHK handler which was using get_user() while
   atomic

 - A few build fixes for issues caused by recent changes

Thanks to Benjamin Gray, Christophe Leroy, Kajol Jain, and Naveen N Rao.

* tag 'powerpc-6.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/dexcr: Move HASHCHK trap handler
  powerpc/82xx: Select FSL_SOC
  powerpc: Fix build issue with LD_DEAD_CODE_DATA_ELIMINATION and FTRACE_MCOUNT_USE_PATCHABLE_FUNCTION_ENTRY
  powerpc/watchpoints: Annotate atomic context in more places
  powerpc/watchpoint: Disable pagefaults when getting user instruction
  powerpc/watchpoints: Disable preemption in thread_change_pc()
  powerpc/perf/hv-24x7: Update domain value check

Pull xen fixes from Juergen Gross:

 - remove some unused functions in the Xen event channel handling

 - fix a regression (introduced during the merge window) when booting as
   Xen PV guest

 - small cleanup removing another strncpy() instance

* tag 'for-linus-6.6a-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  xen/efi: refactor deprecated strncpy
  x86/xen: allow nesting of same lazy mode
  x86/xen: move paravirt lazy code
  arm/xen: remove lazy mode related definitions
  xen: simplify evtchn_do_upcall() call maze

Pull memblock test fixes from Mike Rapoport:
 "Fix several compilation errors and warnings in memblock tests"

* tag 'fixes-2023-09-21' of git://git.kernel.org/pub/scm/linux/kernel/git/rppt/memblock:
  memblock tests: fix warning ‘struct seq_file’ declared inside parameter list
  memblock tests: fix warning: "__ALIGN_KERNEL" redefined
  memblock tests: Fix compilation errors.

Pull sound fixes from Takashi Iwai:
 "A large collection of fixes around this time.

  All small and mostly trivial fixes.

   - Lots of fixes for the new -Wformat-truncation warnings

   - A fix in ALSA rawmidi core regression and UMP handling

   - Series of Cirrus codec fixes

   - ASoC Intel and Realtek codec fixes

   - Usual HD- and USB-audio quirks and AMD ASoC quirks"

* tag 'sound-6.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (64 commits)
  ALSA: hda/realtek - ALC287 Realtek I2S speaker platform support
  ALSA: hda: cs35l56: Use the new RUNTIME_PM_OPS() macro
  ALSA: usb-audio: scarlett_gen2: Fix another -Wformat-truncation warning
  ALSA: rawmidi: Fix NULL dereference at proc read
  ASoC: SOF: core: Only call sof_ops_free() on remove if the probe was successful
  ASoC: SOF: Intel: MTL: Reduce the DSP init timeout
  ASoC: cs42l43: Add shared IRQ flag for shutters
  ASoC: imx-audmix: Fix return error with devm_clk_get()
  ASoC: hdaudio.c: Add missing check for devm_kstrdup
  ALSA: riptide: Fix -Wformat-truncation warning for longname string
  ALSA: cs4231: Fix -Wformat-truncation warning for longname string
  ALSA: ad1848: Fix -Wformat-truncation warning for longname string
  ALSA: hda: generic: Check potential mixer name string truncation
  ALSA: cmipci: Fix -Wformat-truncation warning
  ALSA: firewire: Fix -Wformat-truncation warning for MIDI stream names
  ALSA: firewire: Fix -Wformat-truncation warning for longname string
  ALSA: xen: Fix -Wformat-truncation warning
  ALSA: opti9x: Fix -Wformat-truncation warning
  ALSA: es1688: Fix -Wformat-truncation warning
  ALSA: cs4236: Fix -Wformat-truncation warning
  ...

Merge tag 'hwmon-for-v6.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull hwmon fix from Guenter Roeck:
 "One patch to drop a non-existent alarm attribute in the nct6775 driver"

* tag 'hwmon-for-v6.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (nct6775) Fix non-existent ALARM warning

Florian Westphal says:

====================
netfilter updates for net

The following three patches fix regressions in the netfilter subsystem:

1. Reject attempts to repeatedly toggle the 'dormant' flag in a single
   transaction.  Doing so makes nf_tables lose track of the real state
   vs. the desired state.  This ends with an attempt to unregister hooks
   that were never registered in the first place, which yields a splat.

2. Fix element counting in the new nftables garbage collection infra
   that came with 6.5:  More than 255 expired elements wraps a counter
   which results in memory leak.

3. Since 6.4 ipset can BUG when a set is renamed while a CREATE command
   is in progress, fix from Jozsef Kadlecsik.

* tag 'nf-23-09-20' of https://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
  netfilter: ipset: Fix race between IPSET_CMD_CREATE and IPSET_CMD_SWAP
  netfilter: nf_tables: fix memleak when more than 255 elements expired
  netfilter: nf_tables: disable toggling dormant table state more than once
====================

Link: https://lore.kernel.org/r/20230920084156.4192-1-fw@strlen.deSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Several places in TC offload code assumed that the return from
 rhashtable_lookup_get_insert_fast() was always either NULL or a valid
 pointer to an existing entry, but in fact that function can return an
 error pointer.  In that case, perform the usual cleanup of the newly
 created entry, then pass up the error, rather than attempting to take a
 reference on the old entry.

Fixes: d902e1a7 ("sfc: bare bones TC offload on EF100")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Link: https://lore.kernel.org/r/20230919183949.59392-1-edward.cree@amd.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

When users attempt to obtain the coalesce setting using the
ethtool command, current code always returns 0 for tx-usecs.
This is because I225/6 always uses a queue pair setting, hence
tx_coalesce_usecs does not return a value during the
igc_ethtool_get_coalesce() callback process. The pair queue
condition checking in igc_ethtool_get_coalesce() is removed by
this patch so that the user gets information of the value of tx-usecs.

Even if i225/6 is using queue pair setting, there is no harm in
notifying the user of the tx-usecs. The implementation of the current
code may have previously been a copy of the legacy code i210.
Since I225 has the queue pair setting enabled, tx-usecs will always adhere
to the user-set rx-usecs value. An error message will appear when the user
attempts to set the tx-usecs value for the input parameters because,
by default, they should only set the rx-usecs value.

This patch also adds the helper function to get the
previous rx coalesce value similar to tx coalesce.

How to test:
User can get the coalesce value using ethtool command.

Example command:
Get: ethtool -c <interface>

Previous output:

rx-usecs: 3
rx-frames: n/a
rx-usecs-irq: n/a
rx-frames-irq: n/a

tx-usecs: 0
tx-frames: n/a
tx-usecs-irq: n/a
tx-frames-irq: n/a

New output:

rx-usecs: 3
rx-frames: n/a
rx-usecs-irq: n/a
rx-frames-irq: n/a

tx-usecs: 3
tx-frames: n/a
tx-usecs-irq: n/a
tx-frames-irq: n/a

Fixes: 8c5ad0da ("igc: Add ethtool support")
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20230919170331.1581031-1-anthony.l.nguyen@intel.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Sebastian Andrzej Siewior says:

====================
Add missing xdp_do_flush() invocations.

I've been looking at the drivers/ XDP users and noticed that some
XDP_REDIRECT user don't invoke xdp_do_flush() at the end.
====================

Link: https://lore.kernel.org/r/20230918153611.165722-1-bigeasy@linutronix.deSigned-off-by: Paolo Abeni <pabeni@redhat.com>

xdp_do_flush() should be invoked before leaving the NAPI poll function
if XDP-redirect has been performed.

Invoke xdp_do_flush() before leaving NAPI.

Cc: Geetha sowjanya <gakula@marvell.com>
Cc: Subbaraya Sundeep <sbhatta@marvell.com>
Cc: Sunil Goutham <sgoutham@marvell.com>
Cc: hariprasad <hkelam@marvell.com>
Fixes: 06059a1a ("octeontx2-pf: Add XDP support to netdev PF")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Geethasowjanya Akula <gakula@marvell.com>
Acked-by: Jesper Dangaard Brouer <hawk@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

bnxt_poll_nitroa0() invokes bnxt_rx_pkt() which can run a XDP program
which in turn can return XDP_REDIRECT. bnxt_rx_pkt() is also used by
__bnxt_poll_work() which flushes (xdp_do_flush()) the packets after each
round. bnxt_poll_nitroa0() lacks this feature.
xdp_do_flush() should be invoked before leaving the NAPI callback.

Invoke xdp_do_flush() after a redirect in bnxt_poll_nitroa0() NAPI.

Cc: Michael Chan <michael.chan@broadcom.com>
Fixes: f18c2b77 ("bnxt_en: optimized XDP_REDIRECT support")
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Jesper Dangaard Brouer <hawk@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

xdp_do_flush() should be invoked before leaving the NAPI poll function
after a XDP-redirect. This is not the case if the driver leaves via
the error path (after having a redirect in one of its previous
iterations).

Invoke xdp_do_flush() also in the error path.

Cc: Arthur Kiyanovski <akiyano@amazon.com>
Cc: David Arinzon <darinzon@amazon.com>
Cc: Noam Dagan <ndagan@amazon.com>
Cc: Saeed Bishara <saeedb@amazon.com>
Cc: Shay Agroskin <shayagr@amazon.com>
Fixes: a318c70a ("net: ena: introduce XDP redirect implementation")
Acked-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Jesper Dangaard Brouer <hawk@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Pull media fixes from Mauro Carvalho Chehab:

 - driver fixes due to incorrect fwnode_handle_put() call

 - bt8xx: bttv_risc_packed(): remove field checks

 - vb2: frame_vector.c: replace WARN_ONCE with a comment

 - imx219: a couple typo fixes and perform a full mode set
   unconditionally

 - uvcvideo: Fix OOB read

 - some dependency fixes

* tag 'media/v6.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
  media: imx-mipi-csis: Remove an incorrect fwnode_handle_put() call
  media: vb2: frame_vector.c: replace WARN_ONCE with a comment
  media: uvcvideo: Fix OOB read
  media: bt8xx: bttv_risc_packed(): remove field checks
  media: i2c: rdacm21: Remove an incorrect fwnode_handle_put() call
  media: i2c: imx219: Perform a full mode set unconditionally
  media: i2c: imx219: Fix crop rectangle setting when changing format
  media: i2c: imx219: Fix a typo referring to a wrong variable
  media: i2c: max9286: Remove an incorrect fwnode_handle_put() call
  media: ivsc: Depend on VIDEO_DEV
  media: via: Use correct dependency for camera sensor drivers
  media: v4l: Use correct dependency for camera sensor drivers
  media: pci: ivsc: Select build dependencies

Pull btrfs fixes from David Sterba:
 "A few more followup fixes to the directory listing.

  People have noticed different behaviour compared to other filesystems
  after changes in 6.5. This is now unified to more "logical" and
  expected behaviour while still within POSIX. And a few more fixes for
  stable.

   - change behaviour of readdir()/rewinddir() when new directory
     entries are created after opendir(), properly tracking the last
     entry

   - fix race in readdir when multiple threads can set the last entry
     index for a directory

  Additionally:

   - use exclusive lock when direct io might need to drop privs and call
     notify_change()

   - don't clear uptodate bit on page after an error, this may lead to a
     deadlock in subpage mode

   - fix waiting pattern when multiple readers block on Merkle tree
     data, switch to folios"

* tag 'for-6.6-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  btrfs: fix race between reading a directory and adding entries to it
  btrfs: refresh dir last index during a rewinddir(3) call
  btrfs: set last dir index to the current last index when opening dir
  btrfs: don't clear uptodate on write errors
  btrfs: file_remove_privs needs an exclusive lock in direct io write
  btrfs: convert btrfs_read_merkle_tree_page() to use a folio

The following memory leak can be observed when the controller supports
codecs which are stored in local_codecs list but the elements are never
freed:

unreferenced object 0xffff88800221d840 (size 32):
  comm "kworker/u3:0", pid 36, jiffies 4294898739 (age 127.060s)
  hex dump (first 32 bytes):
    f8 d3 02 03 80 88 ff ff 80 d8 21 02 80 88 ff ff  ..........!.....
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  backtrace:
    [<ffffffffb324f557>] __kmalloc+0x47/0x120
    [<ffffffffb39ef37d>] hci_codec_list_add.isra.0+0x2d/0x160
    [<ffffffffb39ef643>] hci_read_codec_capabilities+0x183/0x270
    [<ffffffffb39ef9ab>] hci_read_supported_codecs+0x1bb/0x2d0
    [<ffffffffb39f162e>] hci_read_local_codecs_sync+0x3e/0x60
    [<ffffffffb39ff1b3>] hci_dev_open_sync+0x943/0x11e0
    [<ffffffffb396d55d>] hci_power_on+0x10d/0x3f0
    [<ffffffffb30c99b4>] process_one_work+0x404/0x800
    [<ffffffffb30ca134>] worker_thread+0x374/0x670
    [<ffffffffb30d9108>] kthread+0x188/0x1c0
    [<ffffffffb304db6b>] ret_from_fork+0x2b/0x50
    [<ffffffffb300206a>] ret_from_fork_asm+0x1a/0x30

Cc: stable@vger.kernel.org
Fixes: 8961987f ("Bluetooth: Enumerate local supported codec and cache details")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

This fixes the following warnings:

net/bluetooth/hci_core.c: In function ‘hci_register_dev’:
net/bluetooth/hci_core.c:2620:54: warning: ‘%d’ directive output may
be truncated writing between 1 and 10 bytes into a region of size 5
[-Wformat-truncation=]
 2620 |         snprintf(hdev->name, sizeof(hdev->name), "hci%d", id);
      |                                                      ^~
net/bluetooth/hci_core.c:2620:50: note: directive argument in the range
[0, 2147483647]
 2620 |         snprintf(hdev->name, sizeof(hdev->name), "hci%d", id);
      |                                                  ^~~~~~~
net/bluetooth/hci_core.c:2620:9: note: ‘snprintf’ output between 5 and
14 bytes into a destination of size 8
 2620 |         snprintf(hdev->name, sizeof(hdev->name), "hci%d", id);
      |         ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

While executing the Android 13 CTS Verifier Secure Server test on a
ChromeOS device, it was observed that the Bluetooth host initiates
authentication for an RFCOMM connection after SSP completes.
When this happens, some Intel Bluetooth controllers, like AC9560, would
disconnect with "Connection Rejected due to Security Reasons (0x0e)".

Historically, BlueZ did not mandate this authentication while an
authenticated combination key was already in use for the connection.
This behavior was changed since commit 7b5a9241
("Bluetooth: Introduce requirements for security level 4").
So, this patch addresses the aforementioned disconnection issue by
restoring the previous behavior.
Signed-off-by: Ying Hsu <yinghsu@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

iso_listen_cis shall only return -EADDRINUSE if the listening socket has
the destination set to BDADDR_ANY otherwise if the destination is set to
a specific address it is for broadcast which shall be ignored.

Fixes: f764a6c2 ("Bluetooth: ISO: Add broadcast support")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Syzbot found a bug "BUG: sleeping function called from invalid context
at kernel/locking/mutex.c:580". It is because hci_link_tx_to holds an
RCU read lock and calls hci_disconnect which would hold a mutex lock
since the commit a13f316e ("Bluetooth: hci_conn: Consolidate code
for aborting connections"). Here's an example call trace:

   __dump_stack lib/dump_stack.c:88 [inline]
   dump_stack_lvl+0xfc/0x174 lib/dump_stack.c:106
   ___might_sleep+0x4a9/0x4d3 kernel/sched/core.c:9663
   __mutex_lock_common kernel/locking/mutex.c:576 [inline]
   __mutex_lock+0xc7/0x6e7 kernel/locking/mutex.c:732
   hci_cmd_sync_queue+0x3a/0x287 net/bluetooth/hci_sync.c:388
   hci_abort_conn+0x2cd/0x2e4 net/bluetooth/hci_conn.c:1812
   hci_disconnect+0x207/0x237 net/bluetooth/hci_conn.c:244
   hci_link_tx_to net/bluetooth/hci_core.c:3254 [inline]
   __check_timeout net/bluetooth/hci_core.c:3419 [inline]
   __check_timeout+0x310/0x361 net/bluetooth/hci_core.c:3399
   hci_sched_le net/bluetooth/hci_core.c:3602 [inline]
   hci_tx_work+0xe8f/0x12d0 net/bluetooth/hci_core.c:3652
   process_one_work+0x75c/0xba1 kernel/workqueue.c:2310
   worker_thread+0x5b2/0x73a kernel/workqueue.c:2457
   kthread+0x2f7/0x30b kernel/kthread.c:319
   ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:298

This patch releases RCU read lock before calling hci_disconnect and
reacquires it afterward to fix the bug.

Fixes: a13f316e ("Bluetooth: hci_conn: Consolidate code for aborting connections")
Signed-off-by: Ying Hsu <yinghsu@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

When HCI_QUIRK_STRICT_DUPLICATE_FILTER is set LE scanning requires
periodic restarts of the scanning procedure as the controller would
consider device previously found as duplicated despite of RSSI changes,
but in order to set the scan timeout properly set le_scan_restart needs
to be synchronous so it shall not use hci_cmd_sync_queue which defers
the command processing to cmd_sync_work.

Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/linux-bluetooth/578e6d7afd676129decafba846a933f5@agner.ch/#t
Fixes: 27d54b77 ("Bluetooth: Rework le_scan_restart for hci_sync")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

We should send hci reset command before bt turn off, which can reset bt
firmware status.
Signed-off-by: Rocky Liao <quic_rjliao@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

hci_req_prepare_suspend() has been deprecated in favor of
hci_suspend_sync().

Fixes: 182ee45d ("Bluetooth: hci_sync: Rework hci_suspend_notifier")
Signed-off-by: Yao Xiao <xiaoyao@rock-chips.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Pull spi fixes from Mark Brown:
 "A small collection of fixes, plus a new device ID for Intel Granite
  Rapids systems.

  The fix for the i.MX driver is fairly urgent, it's fixing a data
  corruption issue when bits per word isn't 8.

  There's also one fix which was queued but not sent for v6.4 due to
  being minor and arriving at the end of the release"

* tag 'spi-fix-v6.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
  spi: imx: Take in account bits per word instead of assuming 8-bits
  spi: intel-pci: Add support for Granite Rapids SPI serial flash
  spi: stm32: add a delay before SPI disable
  spi: nxp-fspi: reset the FLSHxCR1 registers
  spi: zynqmp-gqspi: fix clock imbalance on probe failure