Change the function that deletes offloaded TC rule to get
struct mlx5e_tc_flow instance which contains both the flow
handle and flow attributes. This is a cleanup needed for
downstream patches, it doesn't change any functionality.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

According to the reverse unwinding principle, on delete time we should
first handle deletion of the steering rule and later handle the vlan
deletion from the eswitch.

Fixes: 8b32580d ("net/mlx5e: Add TC vlan action for SRIOV offloads")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We will never find a flow with the same cookie as cls_flower always
allocates a new flow and the cookie is the allocated memory address.

Fixes: e3a2b7ed ("net/mlx5e: Support offload cls_flower with drop action")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In Striding RQ implementation, we used a single UMR
(User-Mode Memory Registration) memory key for all RQs.
When the product of RQs number*size gets high, we hit a
limitation of u16 field size in FW.

Here we move to using a UMR memory key per RQ, so we can
scale to any number of rings, with the maximum buffer
size in each.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In next patch we are going to create a UMR MKey per RQ, we need
mlx5e_create_umr_mkey declared before mlx5e_create_rq.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add new type of struct mlx5_frag_buf which is used to allocate fragmented
buffers rather than contiguous, and make the Completion Queues (CQs) use
it as they are big (default of 2MB per CQ in Striding RQ).

This fixes the failures of type:
"mlx5e_open_locked: mlx5e_open_channels failed, -12"
due to dma_zalloc_coherent insufficient contiguous coherent memory to
satisfy the driver's request when the user tries to setup more or larger
rings.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reported-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Neill Whillans says:

====================
net: Add support for SGMII PCS on Altera TSE MAC

These patches were created as part of work to add support for SGMII
PCS functionality to the Altera TSE MAC. Patches are based on 4.9-rc6
git tree.

The first patch in the series adds support for the VSC8572 dual-port
Gigabit Ethernet transceiver, used in integration testing.

The second patch adds support for the SGMII PCS functionality to the
Altera TSE driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for the (optional) SGMII PCS functionality of the Altera
TSE MAC. If the phy-mode is set to 'sgmii' then we attempt to discover
and initialise the PCS so that the MAC can communicate to the PHY.

The PCS IP block provides a scratch register for testing presence of
the PCS, which is mapped into one of the two MDIO spaces present in
the MAC's register space.  Once we have determined that the scratch
register is functioning, we attempt to initialise the PCS to
auto-negotiate an SGMII link with the PHY. There is no need to monitor
or manage the SGMII link beyond this, since the normal PHY MDIO will
then be used to monitor the media layer.

The Altera TSE MAC has only one way in which it can be configured with an
SGMII PCS, and as such, this patch only looks to the phy-mode to select
whether or not to attempt to initialise the PCS registers.  During
initialisation, we report the PCS's equivalent of a PHY ID register.
This can be parameterised during the IP instantiation and is often left
as '0x00000000' which is not an error.
Signed-off-by: Neill Whillans <neill.whillans@codethink.co.uk>
Reviewed-by: Daniel Silverstone <daniel.silverstone@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for the Vitesse VSC8572 which is functionally equivalent to
the already supported VSC8574. As such, all the same handling functions
are used since the VSC8572 merely has half the number of phy blocks
internally.
Signed-off-by: Stephen Agate <stephen.agate@uk.thalesgroup.com>
Signed-off-by: Neill Whillans <neill.whillans@codethink.co.uk>
Reviewed-by: Daniel Silverstone <daniel.silverstone@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Edward Cree says:

====================
sfc: defalconisation fixups

A bug fix, the Kconfig change, and cleaning up a bit more unused code.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

It's no longer used now that Falcon is gone.

Also remove a reference in a comment to an ioctl that doesn't exist.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Easy enough for Falcon users to enable it when making oldconfig.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Defalconisation removed one of the string arguments, but missed the
 corresponding %s.

Fixes: 5a6681e2 ("sfc: separate out SFC4000 ("Falcon") support into new sfc-falcon driver")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Before this patch, function ndo_dflt_fdb_dump() will always return code
from uc fdb dump. The reture code of mc fdb dump is lost.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netlink kernel socket is protected by refcount, not RCU.
Its rcv path is neither protected by RCU. So the synchronize_net()
is just pointless.

Cc: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Raju Lakkaraju says:

====================
Adding PHY MDI(X) support

I updated all review comments which were given by Andrew and Florian.

This series add support for PHY MDI(X), and implement it for MSCC phys.

Tested on Beaglebone Black with VSC 8531 PHY.

Change set:
v1:
- Initial patch submit the WoL and MDI-X in single set of patches

v2:
- Split the mdi(x) as signal set of patches.
- Remove the out_unlock as suggested by Andrew.
- Add mdix_ctrl parameter in "phy_device" to handle the user configure
  mdi(x). Proposed implementation accepted by Florian.
- phydev->mdix_ctrl initialize with ETH_TP_MDI_AUTO. Ethernet controller
  never initialize this parameter.
- Fix the mdix changes in marvell and microchip driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

PHY drivers to have an eth_tp_mdix_ctrl to indicate what is the configured
MDI setting, and read eth_tp_mdi to indicate what is the current status,

Add new parameter mdix_ctrl in phy_device structure and fix driver.
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microsemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To connect two ports of the same configuration (MDI to MDI or
MDI-X to MDI-X) with a 10/100/1000 Mbit/s connection, an
Ethernet crossover cable is needed to cross over the transmit
and receive signals in the cable, so that they are matched at
the connector level.
When connecting an MDI port to an MDI-X port a straight through
cable is used while to connect two MDI ports or two MDI-X ports
a crossover cable must be used. Conventionally MDI is used on end
devices while MDI-X is used on hubs and switches

Auto MDI-X automatically detects the required cable connection
type and configures the connection appropriately, removing the
need for crossover cables to interconnect switches or connecting
PCs peer-to-peer.
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microsemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Update the mdix and mdix_ctrl with corresponding ethtool configuration
parameters.
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microsemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add new parameter mdix_ctrl to hold the user configuration.
Existing mdix maintain the current status of MDI(X) crossover performed or
not.
mdix_ctrl can configure either ETH_TP_MDI or ETH_TP_MDI_X orETH_TP_MDI_AUTO.
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microsemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The mtu_adj is initialized to zero when alloc mem, there is no any
assignment to mtu_adj. It is only used in ipvlan_adjust_mtu as one
right value.
So it is useless member of struct ipvl_dev, then remove it.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In alloc_cmd_box(), pci_pool_alloc() followed by memset will be
replaced by pci_pool_zalloc()
Signed-off-by: Souptick joarder <jrdr.linux@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In mlx4_alloc_cmd_mailbox(), pci_pool_alloc() followed by memset will be
replaced by pci_pool_zalloc()
Signed-off-by: Souptick joarder <jrdr.linux@gmail.com>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit e2d118a1 ("net: inet: Support UID-based routing in IP
protocols.") made __build_flow_key call sock_net(sk) to determine
the network namespace of the passed-in socket. This crashes if sk
is NULL.

Fix this by getting the network namespace from the skb instead.

Fixes: e2d118a1 ("net: inet: Support UID-based routing in IP protocols.")
Reported-by: Erez Shitrit <erezsh@dev.mellanox.co.il>
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is a test to verify that

bpf: fix states equal logic for varlen access

actually fixed the problem.  The problem was if the register we added to our map
register was UNKNOWN in both the false and true branches and the only thing that
changed was the range then we'd incorrectly assume that the true branch was
valid, which it really wasnt.  This tests this case and properly fails without
my fix in place and passes with it in place.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ivan Khoronzhuk says:

====================
cpsw: add per channel shaper configuration

This series is intended to allow user to set rate for per channel
shapers at cpdma level. This patchset doesn't have impact on performance.
The rate can be set with:

echo 100 > /sys/class/net/ethX/queues/tx-0/tx_maxrate

Tested on am572xx
Based on net-next/master
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Split device budget between channels according to channel rate.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Check budget fullness only after it's updated and update
channel mask only once to keep budget balance between channels.
It's also needed for farther changes.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch allows to rate limit queues tx queues for cpsw interface.
The rate is set in absolute Mb/s units and cannot be more a speed
an interface is connected with.

The rate for a tx queue can be tested with:

ethtool -L eth0 rx 4 tx 4

echo 100 > /sys/class/net/eth0/queues/tx-0/tx_maxrate
echo 200 > /sys/class/net/eth0/queues/tx-1/tx_maxrate
echo 50 > /sys/class/net/eth0/queues/tx-2/tx_maxrate
echo 30 > /sys/class/net/eth0/queues/tx-3/tx_maxrate

tc qdisc add dev eth0 root handle 1: multiq

tc filter add dev eth0 parent 1: protocol ip prio 1 u32 match ip\
dport 5001 0xffff action skbedit queue_mapping 0

tc filter add dev eth0 parent 1: protocol ip prio 1 u32 match ip\
dport 5002 0xffff action skbedit queue_mapping 1

tc filter add dev eth0 parent 1: protocol ip prio 1 u32 match ip\
dport 5003 0xffff action skbedit queue_mapping 2

tc filter add dev eth0 parent 1: protocol ip prio 1 u32 match ip\
dport 5004 0xffff action skbedit queue_mapping 3

iperf -c 192.168.2.1 -b 110M -p 5001 -f m -t 60
iperf -c 192.168.2.1 -b 215M -p 5002 -f m -t 60
iperf -c 192.168.2.1 -b 55M -p 5003 -f m -t 60
iperf -c 192.168.2.1 -b 32M -p 5004 -f m -t 60
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The cpdma has 8 rate limited tx channels. This patch adds
ability for cpdma driver to use 8 tx h/w shapers. If at least one
channel is not rate limited then it must have higher number, this
is because the rate limited channels have to have higher priority
then not rate limited channels. The channel priority is set in low-hi
direction already, so that when a new channel is added with ethtool
and it doesn't have rate yet, it cannot affect on rate limited
channels. It can be useful for TSN streams and just in cases when
h/w rate limited channels are needed.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The weight of a channel is needed to split descriptors between
channels. The weight can depend on maximum rate of channels, maximum
rate of an interface or other reasons. The channel weight is in
percentage and is independent for rx and tx channels.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Yuval Mintz says:

====================
qed*: Add XDP support

This patch series is intended to add XDP to the qede driver, although
it contains quite a bit of cleanups, refactorings and infrastructure
changes as well.

The content of this series can be roughly divided into:

 - Datapath improvements - mostly focused on having the datapath utilize
parameters which can be more tightly contained in cachelines.
Patches #1, #2, #8, #9 belong to this group.

 - Refactoring - done mostly in favour of XDP. Patches #3, #4, #5, #9.

 - Infrastructure changes - done in favour of XDP. Paches #6 and #7 belong
to this category [#7 being by far the biggest patch in the series].

 - Actual XDP support - last two patches [#10, #11].
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for forwarding via XDP. Once the eBPF is attached,
driver would allocate & configure a designated transmission queue
meant solely for forwarding packets. Said queue would share the
receive-queue's interrupt line, and would have it's own Tx statistics.

Infrastructure changes required for this [spread-out through the code]:
 - Determine the DMA direction of the receive buffers based on the presence
of the eBPF program.
 - Turn the sw Tx ring into a union, as regular/XDP queues have different
needs for releasing resources after completion [regular requires the SKB,
XDP requires the transmitted page].
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for the ndo_xdp callback. This patch would support XDP_PASS,
XDP_DROP and XDP_ABORTED commands.

This also adds a per Rx queue statistic which counts number of packets
which didn't reach the stack [due to XDP].
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Improve the cacheline usage of both queues by reordering -
This reduces the cachelines required for egress datapath processing
from 3 to 2 and those required by ingress datapath processing by 2.

It also changes a couple of datapath related functions that currently
require either the fastpath or the qede_dev, changing them to be based
on the tx/rx queue instead.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Receive-hashing is a fixed feature, so there's no need to check
during the ingress datapath whether it's set or not.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver needs to maintain several FW/HW-indices for each one of
its queues. Currently, that mapping is done by the QED where it uses
an rx/tx array of so-called hw-cids, populating them whenever a new
queue is opened and clearing them upon destruction of said queues.

This maintenance is far from ideal - there's no real reason why
QED needs to maintain such a data-structure. It becomes even worse
when considering the fact that the PF's queues and its child VFs' queues
are all mapped into the same data-structure.
As a by-product, the set of parameters an interface needs to supply for
queue APIs is non-trivial, and some of the variables in the API
structures have different meaning depending on their exact place
in the configuration flow.

This patch re-organizes the way L2 queues are configured and maintained.
In short:
  - Required parameters for queue init are now well-defined.
  - Qed would allocate a queue-cid based on parameters.
    Upon initialization success, it would return a handle to caller.
  - Queue-handle would be maintained by entity requesting queue-init,
    not necessarily qed.
  - All further queue-APIs [update, destroy] would use the opaque
    handle as reference for the queue instead of various indices.

The possible owners of such handles:
  - PF queues [qede] - complete handles based on provided configuration.
  - VF queues [qede] - fw-context-less handles, containing only relative
    information; Only the PF-side would need the absolute indices
    for configuration, so they're omitted here.
  - VF queues [qed, PF-side] - complete handles based on VF initialization.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As qede utilizes an internal-reload sequence as result of various
configuration changes, the netif state wouldn't always accurately describe
the status of the configuration.
To compensate, we're storing an internal state of the device, which should
only be accessed under the qede_lock.

This patch fixes and improves several state/lock interactions:
  - The internal state should only be checked while locked.
  - While holding lock, it's preferable to check state rather than
    the netdevice's state.
  - The reload sequence is not 'atomic' - unload and subsequent load
    are not in the same critical section.

This also add the 'locked' variant for the reload, which would later be
used by XDP - useful in the case where the correct sequence is 'lock,
check state and re-configure if good', instead of allowing the reload
itself to make the decision regarding the configurability of the device.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Driver's NAPI poll is using a long sequence for processing ingress
packets, and it's going to get even longer once we do XDP.
Break down the main loop into a series of sub-functions to allow
better readability of the function.

While we're at it, correct the accounting of the NAPI budget -
currently we're counting only packets passed to the stack against
the budget, even in case those are actually aggregations.
After refactoring every CQE processed would be counted against the budget.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Refactor logic for gathering statistics into a per-queue function.
This improves readability of the driver statistics' flows.

In addition, this would be required by the XDP forwarding queues
[as we'll need the Txq statistics gathering methods for those as well].
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>