- 11 Mar, 2016 1 commit
-
-
Andre Przywara authored
Based on the Allwinner A64 user manual and on the previous sunxi pinctrl drivers this introduces the pin multiplex assignments for the ARMv8 Allwinner A64 SoC. Port A is apparently used for the fixed function DRAM controller, so the ports start at B here (the manual mentions "n from 1 to 7", so not starting at 0). Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Rob Herring <robh@kernel.org> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
- 10 Mar, 2016 1 commit
-
-
Linus Walleij authored
Linux 4.5-rc5
-
- 09 Mar, 2016 13 commits
-
-
Yendapally Reddy Dhananjaya Reddy authored
Device tree binding documentation for Broadcom NS2 IOMUX Signed-off-by: Yendapally Reddy Dhananjaya Reddy <yendapally.reddy@broadcom.com> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Carlo Caione authored
In the Amlogic Meson8 / Meson8b platforms we have two different buses: cbus and aobus, corresponding to 2 different power domains (regular and always-on). On each bus a different set of registers is mapped to manage muxes, GPIOs and in general to control a clear subset of the pins. Considering this architecture, having two different pinctrl devices, one for each bus / power domain, makes much more sense than just having one single device. Right now we have one single pin controller driver that uses two different domains (represented by 'gpio' and 'gpio-ao' sub-nodes in the DTS) to manage the set of registers on the two buses. This dual-domain configuration is hardcoded into the driver that strictly requires one domain for each bus in the same pin controller device. With this patch we refactor the driver to allow splitting the driver in two parts. This change is needed to have a proper description of the HW in the device-tree where we want to introduce aobus and cbus. Signed-off-by: Carlo Caione <carlo@endlessm.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Carlo Caione authored
Separate functions for pins controlled by different pin controllers. Signed-off-by: Carlo Caione <carlo@endlessm.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Arnd Bergmann authored
The at91-pio4 pinctrl driver uses SET_SYSTEM_SLEEP_PM_OPS() to conditionally set the correct suspend/resume options, but they become unused when CONFIG_PM is disabled: drivers/pinctrl/pinctrl-at91-pio4.c:827:12: error: 'atmel_pctrl_suspend' defined but not used [-Werror=unused-function] drivers/pinctrl/pinctrl-at91-pio4.c:847:12: error: 'atmel_pctrl_resume' defined but not used [-Werror=unused-function] This adds __maybe_unused annotations so the compiler knows it can silently drop them instead of warning. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Wolfram Sang authored
This change will also make Coverity happy by avoiding a theoretical NULL pointer dereference; yet another reason is to use the above helper function to tighten the code and make it more readable. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Acked-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Masahiro Yamada authored
The current "CONFIG_PINCTRL_UNIPHIER_PH1_*" is too long. It would not hurt to drop "PH1_" because "UNIPHIER_" already well specifies the SoC family. Also, rename files for consistency. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Paul Gortmaker authored
The Kconfig currently controlling compilation of this code is: drivers/pinctrl/sunxi/Kconfig:config PINCTRL_SUN9I_A80_R drivers/pinctrl/sunxi/Kconfig: def_bool MACH_SUN9I ...meaning that it currently is not being built as a module by anyone. Lets remove the modular code that is essentially orphaned, so that when reading the driver there is no doubt it is builtin-only. Since module_platform_driver() uses the same init level priority as builtin_platform_driver() the init ordering remains unchanged with this commit. Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code. We also delete the MODULE_LICENSE tag etc. since all that information is already contained at the top of the file in the comments. Cc: Chen-Yu Tsai <wens@csie.org> Cc: linux-gpio@vger.kernel.org Cc: linux-arm-kernel@lists.infradead.org Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Paul Gortmaker authored
The Kconfig currently controlling compilation of this code is: drivers/pinctrl/stm32/Kconfig:config PINCTRL_STM32F429 drivers/pinctrl/stm32/Kconfig: bool "STMicroelectronics STM32F429 pin control" if COMPILE_TEST && !MACH_STM32F429 ...meaning that it currently is not being built as a module by anyone. Lets remove the modular code that is essentially orphaned, so that when reading the driver there is no doubt it is builtin-only. Since module_init translates to device_initcall in the non-modular case, the init ordering remains unchanged with this commit. Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code. We also delete the MODULE_LICENSE tag etc. since all that information is already contained at the top of the file in the comments. Cc: Patrice Chotard <patrice.chotard@st.com> Cc: linux-gpio@vger.kernel.org Cc: linux-arm-kernel@lists.infradead.org Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Acked-by: Maxime Coquelin <mcoquelin.stm32@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Paul Gortmaker authored
The Kconfig / Makefile currently controlling compilation of this code is: drivers/pinctrl/sh-pfc/Makefile:obj-$(CONFIG_PINCTRL_SH_PFC) += sh-pfc.o drivers/pinctrl/sh-pfc/Makefile:sh-pfc-objs = core.o pinctrl.o drivers/pinctrl/sh-pfc/Kconfig:config PINCTRL_SH_PFC drivers/pinctrl/sh-pfc/Kconfig: def_bool y ...meaning that it currently is not being built as a module by anyone. Lets remove the modular code that is essentially orphaned, so that when reading the driver there is no doubt it is builtin-only. Since module_init already wasn't being used in this code, the init ordering remains unchanged with this commit. Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code. We also delete the MODULE_LICENSE tag etc. since all that information was (or is now) contained at the top of the file in the comments. Cc: linux-renesas-soc@vger.kernel.org Cc: linux-gpio@vger.kernel.org Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Paul Gortmaker authored
The Kconfig currently controlling compilation of this code is: drivers/pinctrl/Kconfig:config PINCTRL_MESON drivers/pinctrl/Kconfig: bool ...meaning that it currently is not being built as a module by anyone. Lets remove the couple traces of modularity so that when reading the driver there is no doubt it is builtin-only. Since module_platform_driver() uses the same init level priority as builtin_platform_driver() the init ordering remains unchanged with this commit. We don't replace module.h with init.h since the file already has that. Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code. We also delete the MODULE_LICENSE tag etc. since all that information is already contained at the top of the file in the comments. Cc: Beniamino Galvani <b.galvani@gmail.com> Cc: Carlo Caione <carlo@endlessm.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Antoine Tenart <antoine.tenart@free-electrons.com> Cc: linux-gpio@vger.kernel.org Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Paul Gortmaker authored
The Kconfig for this driver is currently: config PINCTRL_MT6397 bool "Mediatek MT6397 pin control" if COMPILE_TEST && !MFD_MT6397 ...meaning that it is currently not being built as a module by anyone. Lets remove the modular code that is essentially orphaned, so that when reading the driver there is no doubt it is builtin-only. Since module_init translates to device_initcall in the non-modular case, the init ordering remains unchanged with this commit. We also delete the MODULE_LICENSE tag etc. since all that information is already contained at the top of the file in the comments. Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code. Cc: Matthias Brugger <matthias.bgg@gmail.com> Cc: linux-gpio@vger.kernel.org Cc: linux-mediatek@lists.infradead.org Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Acked-by: Hongzhou Yang <hongzhou.yang@mediatek.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Paul Gortmaker authored
This file is not modular, nor is it using modular functions. The only thing close is the global THIS_MODULE which comes from export.h so lets replace it appropriately and cut back on the amount of header stuff we draw in by several thousand lines. Cc: linux-gpio@vger.kernel.org Cc: linux-arm-kernel@lists.infradead.org Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Linus Walleij authored
The pxa2xxx fails some automated builds because of unexported symbols. Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
- 08 Mar, 2016 4 commits
-
-
Henry Paulissen authored
While I was testing irq's on the cubietruck I found a couple of not working irq pins. Further diving into the problem it opened up a mess called "manual". This so called manual (A20 user manual v1.3 dated 2014-10-10) says: Pin overview: Page 237: EINT26 is on mux 5. Page 288: EINT26 is on mux 6. The manual is so contradicting that further tests had to be made to see which of the 2 statements where correct. This patch is based on actual outcome of these tests and not what the manual says. Test procedure used: Connect a 1 pulse per second (GPS) line to the pin. echo pin### > /sys/class/gpio/export echo in > /sys/class/gpio/gpio###/direction echo rising > /sys/class/gpio/gpio###/edge Check /proc/interrupts if a irq was attached and if irq's where received. Hardware used: Henry Paulissen: Cubietruck Andere Przywara: BananaPi M1 Tested-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Henry Paulissen <henry@nitronetworks.nl> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Henry Paulissen authored
While I was testing irq's on the cubietruck I found a couple of not working irq pins. Further diving into the problem it opened up a mess called "manual". This so called manual (A20 user manual v1.3 dated 2014-10-10) says: Pin overview: Page 233: EINT12 is on pin PC19 mux6. Page 236: EINT12 is on pin PH12 mux6. Now, it is a bit strange to have the same IRQ on 2 different pins, but I guess this could still be possible hardware wise. But then: Pin registers: Page 253: EINT12 is *not* on pin PC19. Page 281: EINT12 is on pin PH12. The manual is so contradicting that further tests had to be made to see which of the 2 statements where correct. This patch is based on actual outcome of these tests and not what the manual says. Test procedure used: Connect a 1 pulse per second (GPS) line to the pin. echo pin### > /sys/class/gpio/export echo in > /sys/class/gpio/gpio###/direction echo rising > /sys/class/gpio/gpio###/edge Check /proc/interrupts if a irq was attached and if irq's where received. Signed-off-by: Henry Paulissen <henry@nitronetworks.nl> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Philipp Zabel authored
Commit bdb0066d ("mfd: syscon: Decouple syscon interface from platform devices") added the possibility to register syscon devices without associated platform device. This also removed regmap debugfs facilities, which don't work without a device. This patch associates the syscon regmap that handles the IOMUX controller's general purpose registers with the pinctrl device so that the GPR registers appear in the regmap debugfs directory again. For example, on i.MX6Q the GPR registers now can be read from /sys/kernel/debug/regmap/20e0000.iomuxc-gpr/registers. Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Acked-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Phil Elwell authored
The DT bindings for pinctrl-bcm2835 allow both the function and pull to contain either one entry or one per pin. However, an error in the DT parsing can cause failures if the number of pulls differs from the number of functions. Cc: stable@vger.kernel.org Signed-off-by: Eric Anholt <eric@anholt.net> Signed-off-by: Phil Elwell <phil@raspberrypi.org> Reviewed-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
- 07 Mar, 2016 4 commits
-
-
Joachim Eastwood authored
Update devicetree documention for lpc1850-scu with the new nxp,gpio-pin-interrupt property. Signed-off-by: Joachim Eastwood <manabian@gmail.com> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Joachim Eastwood authored
Add support for setting up GPIO pin interrupts in the lpc18xx pinctrl driver. The LPC18xx SCU contain two registers that sets up the signal routing to the GPIO pin interrupt (PINT) block. The routing uses the GPIO namespace and not the pin namespace so a lookup is preformed on the pin. Routing configuration is done in the device tree by using the new nxp,gpio-pin-interrupt property. This property takes single parameter which sets the PINT hwirq for the GPIO. Signed-off-by: Joachim Eastwood <manabian@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Joachim Eastwood authored
pinctrl_find_gpio_range_from_pin takes the pctldev->mutex but so does pinconf_pins_show and this will cause a deadlock if pinctrl_find_gpio_range_from_pin is used in .pin_config_get callback. Create a nolock version of pinctrl_find_gpio_range_from_pin to allow pin to gpio lookup to be used from pinconf_pins_show. Signed-off-by: Joachim Eastwood <manabian@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Colin Ian King authored
The initialization of ngroups is occurring at the end of the first iteration of the outer loop, which means that the assignment pins[ngroups++] = i is potentially indexing into a region outside of array pins because ngroups is not initialized. Instead, initialize ngroups in the inner loop before the first inner loop iteration. Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Joachim Eastwood <manabian@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
- 03 Mar, 2016 1 commit
-
-
Linus Walleij authored
Merge branch 'sh-pfc-for-v4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
-
- 26 Feb, 2016 4 commits
-
-
Ramesh Shanmugasundaram authored
This patch adds CANFD[0-1] pinmux support to r8a7795 SoC. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
-
Ramesh Shanmugasundaram authored
This patch adds CAN[0-1] pinmux support to r8a7795 SoC. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
-
Andrey Gusakov authored
GP2[29] muxing is controlled by 2-bit IP6[3:2] field, yet only 3 values are listed instead of 4... [Sergei: fixed up the formatting, renamed, added the changelog.] Signed-off-by: Andrey Gusakov <andrey.gusakov@cogentembedded.com> Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
-
Simon Horman authored
Make use of ARCH_RENESAS in place of ARCH_SHMOBILE. This is part of an ongoing process to migrate from ARCH_SHMOBILE to ARCH_RENESAS the motivation for which being that RENESAS seems to be a more appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs. Signed-off-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
-
- 25 Feb, 2016 2 commits
-
-
Linus Walleij authored
This is set by the device core. Cc: John Crispin <blogic@openwrt.org> Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Krzysztof Adamski authored
allwinner,sun8i-h3-r-pinctrl was added by commit ba83a111 ("pinctrl: sunxi: Add H3 R_PIO controller support") but the patch was missing proper binding documentation. This patch fixes this issue. Signed-off-by: Krzysztof Adamski <k@japko.eu> Acked-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
- 20 Feb, 2016 8 commits
-
-
Linus Torvalds authored
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull x86 fixes from Ingo Molnar: "This is unusually large, partly due to the EFI fixes that prevent accidental deletion of EFI variables through efivarfs that may brick machines. These fixes are somewhat involved to maintain compatibility with existing install methods and other usage modes, while trying to turn off the 'rm -rf' bricking vector. Other fixes are for large page ioremap()s and for non-temporal user-memcpy()s" * 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/mm: Fix vmalloc_fault() to handle large pages properly hpet: Drop stale URLs x86/uaccess/64: Handle the caching of 4-byte nocache copies properly in __copy_user_nocache() x86/uaccess/64: Make the __copy_user_nocache() assembly code more readable lib/ucs2_string: Correct ucs2 -> utf8 conversion efi: Add pstore variables to the deletion whitelist efi: Make efivarfs entries immutable by default efi: Make our variable validation list include the guid efi: Do variable name validation tests in utf8 efi: Use ucs2_as_utf8 in efivarfs instead of open coding a bad version lib/ucs2_string: Add ucs2 -> utf8 helper functions
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull perf fixes from Ingo Molnar: "A handful of CPU hotplug related fixes" * 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: perf/core: Plug potential memory leak in CPU_UP_PREPARE perf/core: Remove the bogus and dangerous CPU_DOWN_FAILED hotplug state perf/core: Remove bogus UP_CANCELED hotplug state perf/x86/amd/uncore: Plug reference leak
-
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linuxLinus Torvalds authored
Pull powerpc fixes from Michael Ellerman: - Fix build error on 32-bit with checkpoint restart from Aneesh Kumar - Fix dedotify for binutils >= 2.26 from Andreas Schwab - Don't trace hcalls on offline CPUs from Denis Kirjanov - eeh: Fix stale cached primary bus from Gavin Shan - eeh: Fix stale PE primary bus from Gavin Shan - mm: Fix Multi hit ERAT cause by recent THP update from Aneesh Kumar K.V - ioda: Set "read" permission when "write" is set from Alexey Kardashevskiy * tag 'powerpc-4.5-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: powerpc/ioda: Set "read" permission when "write" is set powerpc/mm: Fix Multi hit ERAT cause by recent THP update powerpc/powernv: Fix stale PE primary bus powerpc/eeh: Fix stale cached primary bus powerpc/pseries: Don't trace hcalls on offline CPUs powerpc: Fix dedotify for binutils >= 2.26 powerpc/book3s_32: Fix build error with checkpoint restart
-
git://git.infradead.org/users/vkoul/slave-dmaLinus Torvalds authored
Pull dmaengine fixes from Vinod Koul: "A few fixes for drivers, nothing major here. Fixes are: iotdma fix to restart channels, new ID for wildcat PCH, residue fix for edma, disable irq for non-cyclic in dw" * tag 'dmaengine-fix-4.5-rc5' of git://git.infradead.org/users/vkoul/slave-dma: dmaengine: dw: disable BLOCK IRQs for non-cyclic xfer dmaengine: edma: fix residue race for cyclic dmaengine: dw: pci: add ID for WildcatPoint PCH dmaengine: IOATDMA: fix timer code that continues to restart channels during idle
-
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linuxLinus Torvalds authored
Pull clk driver fixes from Stephen Boyd: "An assortment of vendor specific clk drivers fixes, most notably fallout from adding Tegra210 and rockchip rk3036/rk3368 drivers this cycle. There's also the random smattering of sparse/checker fixes, a build "fix" to get the Tango clk driver to compile because the Kconfig symbol was renamed after the fact, and a clk gpio fix for a patch mismerge" * tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (28 commits) clk: gpio: Really allow an optional clock= DT property Revert "clk: qcom: Specify LE device endianness" clk: versatile: mask VCO bits before writing clk: tegra: super: Fix sparse warnings for functions not declared as static clk: tegra: Fix sparse warnings for functions not declared as static clk: tegra: Fix sparse warning for pll_m clk: tegra: Use definition for pll_u override bit clk: tegra: Fix warning caused by pll_u failing to lock clk: tegra: Fix clock sources for Tegra210 EMC clk: tegra: Add the APB2APE audio clock on Tegra210 clk: tegra: Add missing of_node_put() clk: tegra: Fix PLLE SS coefficients clk: tegra: Fix typos around clearing PLLE bits during enable clk: tegra: Do not disable PLLE when under hardware control clk: tegra: Fix pllx dyn step calculation clk: tegra: pll: Fix potential sleeping-while-atomic clk: tegra: Fix the misnaming of nvenc from msenc clk: tegra: Fix naming of MISC registers clk: tango4: rename ARCH_TANGOX to ARCH_TANGO clk: scpi: Fix checking return value of platform_device_register_simple() ...
-
git://people.freedesktop.org/~airlied/linuxLinus Torvalds authored
Pull more drm fixes from Dave Airlie: "Some more fixes trickled in: A bunch of VC4 ones since it's a pretty new driver not much chance of regressions, and it fixes GPU resets. Also one atomic fix, one set of fixes for a common bug in TTM cleanup, and one i915 hotplug fix" * 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: drm/nouveau: use post-decrement in error handling drm/atomic: Allow for holes in connector state, v2. drm/i915: Fix hpd live status bits for g4x drm/vc4: Use runtime PM to power cycle the device when the GPU hangs. drm/vc4: Enable runtime PM. drm/vc4: Fix spurious GPU resets due to BO reuse. drm/vc4: Drop error message on seqno wait timeouts. drm/vc4: Fix -ERESTARTSYS error return from BO waits. drm/vc4: Return an ERR_PTR from BO creation instead of NULL. drm/vc4: Fix the clear color for the first tile rendered. drm/vc4: Validate that WAIT_BO padding is cleared. drm/radeon: use post-decrement in error handling drm/amdgpu: use post-decrement in error handling
-
Simon Guinot authored
In __request_region, if a conflict with a BUSY and MUXED resource is detected, then the caller goes to sleep and waits for the resource to be released. A pointer on the conflicting resource is kept. At wake-up this pointer is used as a parent to retry to request the region. A first problem is that this pointer might well be invalid (if for example the conflicting resource have already been freed). Another problem is that the next call to __request_region() fails to detect a remaining conflict. The previously conflicting resource is passed as a parameter and __request_region() will look for a conflict among the children of this resource and not at the resource itself. It is likely to succeed anyway, even if there is still a conflict. Instead, the parent of the conflicting resource should be passed to __request_region(). As a fix, this patch doesn't update the parent resource pointer in the case we have to wait for a muxed region right after. Reported-and-tested-by: Vincent Pelletier <plr.vincent@gmail.com> Signed-off-by: Simon Guinot <simon.guinot@sequanux.org> Tested-by: Vincent Donnefort <vdonnefort@gmail.com> Cc: stable@kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
- 19 Feb, 2016 2 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4Linus Torvalds authored
Pull ext4 bugfixes from Ted Ts'o: "Miscellaneous ext4 bug fixes for v4.5" * tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: ext4: fix crashes in dioread_nolock mode ext4: fix bh->b_state corruption ext4: fix memleak in ext4_readdir() ext4: remove unused parameter "newblock" in convert_initialized_extent() ext4: don't read blocks from disk after extents being swapped ext4: fix potential integer overflow ext4: add a line break for proc mb_groups display ext4: ioctl: fix erroneous return value ext4: fix scheduling in atomic on group checksum failure ext4 crypto: move context consistency check to ext4_file_open() ext4 crypto: revalidate dentry after adding or removing the key
-
git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfsLinus Torvalds authored
Pull btrfs fix from Chris Mason: "My for-linus-4.5 branch has a btrfs DIO error passing fix. I know how much you love DIO, so I'm going to suggest against reading it. We'll follow up with a patch to drop the error arg from dio_end_io in the next merge window." * 'for-linus-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs: Btrfs: fix direct IO requests not reporting IO error to user space
-