According to section 10.3.1 of the AHCI spec, PxCMD.ST must not be set
unless there's a device attached. Following this saves us a measurable
quantity of power and does not impair hotplug support. Based on a patch
by Kristen Carlson Accardi.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

This can be used for AHCI-compatible interfaces implemented inside
System-On-Chip solutions, or AHCI devices connected via localbus.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

This patch should contain no functional changes, just moves code
around.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Factor out some ahci_em_messages handling code from ahci_init_one().
We would like to reuse it for non-PCI devices.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Introduce ahci_pci_print_info() that now handles PCI stuff.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Move PCI stuff into ahci_pci_init_controller().
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

To make the function bus-independand we have to get rid of
"struct pci_dev *", so let's pass just "struct devce *".
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Move PCI stuff into ahci_pci_reset_controller().
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

To make the function generic we have to get rid of "struct pci_dev *",
so let's pass just a "struct devce *".
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Make ahci_save_initial_config() a bit more generic by introducing
force_port_map and mask_port_map arguments.

Move PCI stuff into ahci_pci_save_initial_config().
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Currently the driver uses host->iomap to store all the iomapped BARs
of a PCI device (while AHCI devices actually use just a single memory
window).

We're going to teach AHCI to work with non-PCI buses, so there are two
options to make this work:

1. "fake" host->iomap array for non-PCI devices, and place the needed
   address at iomap[AHCI_PCI_BAR];
2. Get rid of host->iomap usage, instead introduce a private mmio
   field.

This patch implements the second option.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

* 'for-linus' of git://git.infradead.org/users/eparis/notify:
  inotify: don't leak user struct on inotify release
  inotify: race use after free/double free in inotify inode marks
  inotify: clean up the inotify_add_watch out path
  Inotify: undefined reference to `anon_inode_getfd'

Manual merge to remove duplicate "select ANON_INODES" from Kconfig file

Merge branch 'davinci-fixes-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci

* 'davinci-fixes-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci:
  DA830: fix USB 2.0 clock entry

DA8xx OHCI driver fails to load due to failing clk_get() call for the USB 2.0
clock. Arrange matching USB 2.0 clock by the clock name instead of the device.
(Adding another CLK() entry for "ohci.0" device won't do -- in the future I'll
also have to enable USB 2.0 clock to configure CPPI 4.1 module, in which case
I won't have any device at all.)
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

inotify_new_group() receives a get_uid-ed user_struct and saves the
reference on group->inotify_data.user.  The problem is that free_uid() is
never called on it.

Issue seem to be introduced by 63c882a0 (inotify: reimplement inotify
using fsnotify) after 2.6.30.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Eric Paris <eparis@parisplace.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Eric Paris <eparis@redhat.com>

There is a race in the inotify add/rm watch code.  A task can find and
remove a mark which doesn't have all of it's references.  This can
result in a use after free/double free situation.

Task A					Task B
------------				-----------
inotify_new_watch()
 allocate a mark (refcnt == 1)
 add it to the idr
					inotify_rm_watch()
					 inotify_remove_from_idr()
					  fsnotify_put_mark()
					      refcnt hits 0, free
 take reference because we are on idr
 [at this point it is a use after free]
 [time goes on]
 refcnt may hit 0 again, double free

The fix is to take the reference BEFORE the object can be found in the
idr.
Signed-off-by: Eric Paris <eparis@redhat.com>
Cc: <stable@kernel.org>

inotify_add_watch explictly frees the unused inode mark, but it can just
use the generic code.  Just do that.
Signed-off-by: Eric Paris <eparis@redhat.com>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  vhost: fix barrier pairing

Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
  mmap_min_addr check CAP_SYS_RAWIO only for write

* 'for-linus' of git://git.monstr.eu/linux-2.6-microblaze:
  microblaze: Fix module loading on system with WB cache
  microblaze: export assembly functions used by modules
  microblaze: Remove powerpc code from Microblaze port
  microblaze: Remove compilation warnings in cache macro
  microblaze: export assembly functions used by modules
  microblaze: fix get_user/put_user side-effects
  microblaze: re-enable interrupts before calling schedule

Redirecting directly to lsm, here's the patch discussed on lkml:
http://lkml.org/lkml/2010/4/22/219

The mmap_min_addr value is useful information for an admin to see without
being root ("is my system vulnerable to kernel NULL pointer attacks?") and
its setting is trivially easy for an attacker to determine by calling
mmap() in PAGE_SIZE increments starting at 0, so trying to keep it private
has no value.

Only require CAP_SYS_RAWIO if changing the value, not reading it.

Comment from Serge :

  Me, I like to write my passwords with light blue pen on dark blue
  paper, pasted on my window - if you're going to get my password, you're
  gonna get a headache.
Signed-off-by: Kees Cook <kees.cook@canonical.com>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
(cherry picked from commit 822cceec)

There is necessary to flush whole dcache. Icache work should be
done in kernel/module.c.
Signed-off-by: Michal Simek <monstr@monstr.eu>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
  mfd: Clean up after WM83xx AUXADC interrupt if it arrives late

* 'kvm-updates/2.6.34' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: PPC: Keep index within boundaries in kvmppc_44x_emul_tlbwe()
  KVM: VMX: blocked-by-sti must not defer NMI injections
  KVM: x86: Call vcpu_load and vcpu_put in cpuid_update
  KVM: SVM: Fix wrong intercept masks on 32 bit
  KVM: convert ioapic lock to spinlock

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
  serial: imx.c: fix CTS trigger level lower to avoid lost chars
  tty: Fix unbalanced BKL handling in error path
  serial: mpc52xx_uart: fix null pointer dereference

The imx CTS trigger level is left at its reset value that is 32
chars. Since the RX FIFO has 32 entries, when CTS is raised, the
FIFO already is full. However, some serial port devices first empty
their TX FIFO before stopping when CTS is raised, resulting in lost
chars.

This patch sets the trigger level lower so that other chars arrive
after CTS is raised, there is still room for 16 of them.

Signed-off-by: Valentin Longchamp<valentin.longchamp@epfl.ch>
Tested-by: Philippe Rétornaz<philippe.retornaz@epfl.ch>
Acked-by: Wolfram Sang<w.sang@pengutronix.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Arnd noted:

After the "retry_open:" label, we first get the tty_mutex
and then the BKL. However a the end of tty_open, we jump
back to retry_open with the BKL still held. If we run into
this case, the tty_open function will be left with the BKL
still held.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Commit 6acc6833
introduced NULL pointer dereference and kernel crash
on ppc32 machines while booting. Fix this bug now.
Reported-by: Leonardo Chiquitto <leonardo.lists@gmail.com>
Tested-by: Leonardo Chiquitto <leonardo.lists@gmail.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
  cifs: guard against hardlinking directories

According to specification

	mkdir d; ln -s d a; open("a/", O_NOFOLLOW | O_RDONLY)

should return success but currently it returns ELOOP.  This is a
regression caused by path lookup cleanup patch series.

Fix the code to ignore O_NOFOLLOW in case the provided path has trailing
slashes.

Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Reported-by: Marius Tolzmann <tolzmann@molgen.mpg.de>
Acked-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ALSA: ice1724 - Fix ESI Maya44 capture source control
  ALSA: pcm - Use pgprot_noncached() for MIPS non-coherent archs
  ALSA: virtuoso: fix Xonar D1/DX front panel microphone
  ALSA: hda - Add hp-dv4 model for IDT 92HD71bx
  ALSA: hda - Fix mute-LED GPIO pin for HP dv series
  ALSA: hda: Fix 0 dB for Lenovo models using Conexant CX20549 (Venice)

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: ad7877 - keep dma rx buffers in seperate cache lines
  Input: psmouse - reset all types of mice before reconnecting
  Input: elantech - use all 3 bytes when checking version
  Input: iforce - fix Guillemot Jet Leader 3D entry
  Input: iforce - add Guillemot Jet Leader Force Feedback

In certain circumstances, especially under heavy load, the AUXADC
completion interrupt may be detected after we've timed out waiting for
it.  That conversion would still succeed but the next conversion will
see the completion that was signalled by the interrupt for the previous
conversion and therefore not wait for the AUXADC conversion to run,
causing it to report failure.

Provide a simple, non-invasive cleanup by using try_wait_for_completion()
to ensure that the completion is not signalled before we wait.  Since
the AUXADC is run within a mutex we know there can only have been at
most one AUXADC interrupt outstanding.  A more involved change should
follow for the next merge window.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Export __strncpy_user, memory_size, ioremap_bot for modules.
Signed-off-by: Michal Simek <monstr@monstr.eu>

Remove eeh_add_device_tree_late which is powerpc specific code.
Signed-off-by: Michal Simek <monstr@monstr.eu>

CC      arch/microblaze/kernel/cpu/cache.o
arch/microblaze/kernel/cpu/cache.c: In function '__invalidate_dcache_range_wb':
arch/microblaze/kernel/cpu/cache.c:398: warning: ISO C90 forbids mixed declarations and code
arch/microblaze/kernel/cpu/cache.c: In function '__flush_dcache_range_wb':
arch/microblaze/kernel/cpu/cache.c:509: warning: ISO C90 forbids mixed declara
Signed-off-by: Michal Simek <monstr@monstr.eu>

Modules that use copy_{to,from}_user(), memcpy(), and memset() fail to build
in certain circumstances.
Signed-off-by: Steven J. Magnani <steve@digidescorp.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>

With dma based spi transmission, data corruption is observed
occasionally. With dma buffers located right next to msg and
xfer fields, cache lines correctly flushed in preparation for
dma usage may be polluted again when writing to fields in the
same cache line.

Make sure cache fields used with dma do not share cache lines
with fields changed during dma handling. As both fields are part
of a struct that is allocated via kzalloc, thus cache aligned,
moving the fields to the 1st position and insert padding for
alignment does the job.
Signed-off-by: Oskar Schirmer <os@emlix.com>
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Signed-off-by: Oliver Schneidewind <osw@emlix.com>
Signed-off-by: Johannes Weiner <jw@emlix.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
[dtor@mail.ru - changed to use ___cacheline_aligned as suggested
 by akpm]
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>