IQ calibration post-processing for AR955x is different
from other chips - instead of just doing it as part
of AGC calibration once, it is triggered 3 times and
a median is determined. This patch adds initial support
for changing the calibration behavior for AR955x.

Also, to simplify things, a helper routine to issue/poll
AGC calibration is used.

For non-AR955x chips, the iqcal_idx (which will be used
in subsequent patches) is set to zero.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Incorrect values are programmed in the registers
containing the IQ correction coefficients by the IQ-CAL
post-processing code. Fix this.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Use ar9003_hw_tx_iq_cal_outlier_detection instead.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In chips like AR955x, the initvals contain the information
whether IQ calibration is to be done in the HW when an
AGC calibration is triggered. Check if IQ-CAL is enabled
in the initvals before flagging 'txiqcal_done' as true.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Calibration data is not reused for SoC chips, so
call ar9003_hw_tx_iq_cal_post_proc() with the correct
argument. The 'is_reusable' flag is currently used
only for PC-OEM chips, but it makes things clearer to
specify it explicity.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Buffalo WLI-UV-AG300P is almost the same as Sony UWA-BR100.
Signed-off-by: Masaki TAGAWA <masaki@club.kyutech.ac.jp>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

There is no benefit in retaining the legacy rate control module
in the driver codebase.

It is known to be buggy and has less than optimal performance
in real-world environments compared with minstrel. The only
reason that it was kept when we made the switch to minstrel
as default was that it showed higher throughput numbers in a
clean/ideal environment.

This is no longer the case and minstrel can push ath9k to
the same throughput levels. In TCP, with 3-stream cards, more than
295 Mbps can be obtained in open air, with 2-stream cards,
210 Mbps is easily reached. To test performance issues,
instead of using a broken rate control module, it is better
to use the fixed-rate interface provided by mac80211 anyway.

The ath9k RC has not received any bug fixes in years and is
just bit-rotting away - this patch removes it.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

... and print what we get.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

after switch to common fucntions we do not need this memcpy any more.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

and rename it to ath9k_cmn_rx_skb_postprocess. We will use it
on ath9k_htc.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

we can reuse it on ath9k_htc
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

we can reuse this function in ath9k_htc
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

we can reuse this fucntion on ath9k_htc.
Now we will need to use common version last_rssi, so switch
it too.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

we need access to this variable from common functions.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

On commit 28f2bce9 I make change that
print various messages as default. This can cause flood of messages
related to TX status timeout on some environments. I partially fixed
problem on commit bb9c298f, but forgot
to move two more messages to debug level.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In the enter and exit download sequence the chip core info was checked
for presence of CM3 ARM core. If found it would enter download state for
the CM3. However, on devices that have a CM3 and CR4 this is not correct
and the CR4 should be used to enter download state. This patch changes
the ARM core lookup giving CR4 precedence.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The brcmf_add_keyext() is for setting per-station key for cipher
algorithms such as WPA1/WPA2 and should not be used to set
WEP broadcast/unicast keys. This patch fixes connect failure
problem with AP using 802.1x-WEP.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Daniel Kim <dekim@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Instead of instantiating core info structs based upon the
chip identifier it is now done parsing information provided
on the device.
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In brcmf_contstruct_reginfo() some error logging was added by:

  commit f7c51a1a72f50870f80001ddf528a6f7f992bc16
  Author: Arend van Spriel <arend@broadcom.com>
  Date:   Wed Dec 11 16:21:21 2013 +0100

      brcmfmac: correct reporting HT40 support in wiphy htcap

This logging was not intended to be delivered and adds a lot
of messages in the log. The patch removes this logging statement.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The function brcmf_sdio_bus_sleep() function is called rather
frequently, which fills the log when TRACE level is enabled. Reduced
the level to SDIO.
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch make several chip related functions host interface
independent by defining callback interface struct brcmf_buscore_ops.
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Currently the function sdio_remove will first destroy the datawork
workqueue and then detach the bus. This can create the situation
where work gets added on non-existing work queue resulting in panic.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmf_sdio_download_code_file is using a loop to send small blobs
of data. This is unnecessarily complex and was simplified with this
patch.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

the function brcmf_sdiod_ramrw is supposed to be able to send
large blobs of data. However inside the loop the skb->len field
did not correctly get reset each round. As a result only small
blobs could be sent. This patch fixes this problem.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Just renaming the file. This file will contain chip related functions
that are independent of the host interface type.
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The chip related functions will be made agnostic of the host
interface. However, some functions in the source file are
rather SDIO specific so better move it to the SDIO specific
source file.
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Address of rte console was not initialized and so console logging
functionality didn't kick in. This patch fixes it and makes console
polling interval a debugfs variable.
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Daniel Kim <dekim@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

To link module attribute with sdio device driver attribute in sysfs.
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Expand the get_station command to also report dtim period and
beacon interval when the device is connected.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

drivers/net/wireless/ath/ath9k/main.c: In function ‘ath9k_has_tx_pending’:
drivers/net/wireless/ath/ath9k/main.c:1869: warning: ‘npend’ may be used uninitialized in this function

Introduced by commit 10e23181 ("ath9k:
optimize ath9k_flush").
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In rtl8180/rtl8187 drivers, few register bit definitions have
names of form FOOBAR_SHIFT, suggesting they should be used as
shift offset, for example
reg |= (1 << ENABLE_FOO_SHIFT).

However they are actually defined as (1 << x) and thus they are
used (correctly) like
reg |= ENABLE_FOO_SHIFT;

This patch kills the misleading _SHIFT suffix.
Signed-off-by: andrea merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The commit "ath9k: Fix IQ calibration" added a check
to ensure that valid i2_p_q2_a0_d1 values are not discarded.
But since it is masked with 0xfff earlier, the codepath
will not be executed.

The earlier case where all values above 0x800 were considered
invalid is incorrect, since the HW can return valid values
between 0x800 and 0xfff.

Cc: Kai Shi <kaishi@qca.qualcomm.com>
Reported-by: Alex Hacker <hacker@epn.ru>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Soon mac80211 will support multi-interface CSA so
using sc->csa_vif is not an option.

Instead just depend on vif->csa_active. Calling
ieee80211_csa_finish() multiple number of times
should not be an issue.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>