- 08 Dec, 2013 26 commits
-
-
KOBAYASHI Yoshitake authored
commit c8760069 upstream. Current MMC driver doesn't handle generic error (bit19 of device status) in write sequence. As a result, write data gets lost when generic error occurs. For example, a generic error when updating a filesystem management information causes a loss of write data and corrupts the filesystem. In the worst case, the system will never boot. This patch includes the following functionality: 1. To enable error checking for the response of CMD12 and CMD13 in write command sequence 2. To retry write sequence when a generic error occurs Messages are added for v2 to show what occurs. Signed-off-by:
KOBAYASHI Yoshitake <yoshitake.kobayashi@toshiba.co.jp> Signed-off-by:
Chris Ball <cjb@laptop.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Kees Cook authored
commit 1e87a245 upstream. A HID device could send a malicious output report that would cause the picolcd HID driver to trigger a NULL dereference during attr file writing. [jkosina@suse.cz: changed report->maxfield < 1 to report->maxfield != 1 as suggested by Bruno]. CVE-2013-2899 Signed-off-by:
Kees Cook <keescook@chromium.org> Cc: stable@kernel.org Reviewed-by:
Bruno Prémont <bonbons@linux-vserver.org> Acked-by:
Jiri Kosina <jkosina@suse.cz> [Kefeng: backported to stable 3.4: adjust filename] Signed-off-by:
Kefeng Wang <wangkefeng.wang@huawei.com> Signed-off-by:
-
fan.du authored
[ Upstream commit 3868204d ] commit a553e4a6 ("[PKTGEN]: IPSEC support") tried to support IPsec ESP transport transformation for pktgen, but acctually this doesn't work at all for two reasons(The orignal transformed packet has bad IPv4 checksum value, as well as wrong auth value, reported by wireshark) - After transpormation, IPv4 header total length needs update, because encrypted payload's length is NOT same as that of plain text. - After transformation, IPv4 checksum needs re-caculate because of payload has been changed. With this patch, armmed pktgen with below cofiguration, Wireshark is able to decrypted ESP packet generated by pktgen without any IPv4 checksum error or auth value error. pgset "flag IPSEC" pgset "flows 1" Signed-off-by:
Fan Du <fan.du@windriver.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Hannes Frederic Sowa authored
[ Upstream commit 7f88c6b2 ] IPv6 stats are 64 bits and thus are protected with a seqlock. By not disabling bottom-half we could deadlock here if we don't disable bh and a softirq reentrantly updates the same mib. Cc: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by:
Hannes Frederic Sowa <hannes@stressinduktion.org> Acked-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit f1d8cba6 ] In commit c9e90429 ("ipv4: fix possible seqlock deadlock") I left another places where IP_INC_STATS_BH() were improperly used. udp_sendmsg(), ping_v4_sendmsg() and tcp_v4_connect() are called from process context, not from softirq context. This was detected by lockdep seqlock support. Reported-by:
jongman heo <jongman.heo@samsung.com> Fixes: 584bdf8c ("[IPV4]: Fix "ipOutNoRoutes" counter error for TCP and UDP") Fixes: c319b4d7 ("net: ipv4: add IPPROTO_ICMP socket kind") Signed-off-by:
-
Shawn Landden authored
[ Upstream commit d3f7d56a ] Commit 35f9c09f (tcp: tcp_sendpages() should call tcp_push() once) added an internal flag MSG_SENDPAGE_NOTLAST, similar to MSG_MORE. algif_hash, algif_skcipher, and udp used MSG_MORE from tcp_sendpages() and need to see the new flag as identical to MSG_MORE. This fixes sendfile() on AF_ALG. v3: also fix udp Reported-and-tested-by:
Shawn Landden <shawnlandden@gmail.com> Cc: Tom Herbert <therbert@google.com> Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: David S. Miller <davem@davemloft.net> Original-patch: Richard Weinberger <richard@nod.at> Signed-off-by:
Shawn Landden <shawn@churchofgit.com> Signed-off-by:
-
Veaceslav Falico authored
[ Upstream commit ec6f809f ] Currently we're using plain spin_lock() in prb_shutdown_retire_blk_timer(), however the timer might fire right in the middle and thus try to re-aquire the same spinlock, leaving us in a endless loop. To fix that, use the spin_lock_bh() to block it. Fixes: f6fb8f10 ("af-packet: TPACKET_V3 flexible buffer implementation.") CC: "David S. Miller" <davem@davemloft.net> CC: Daniel Borkmann <dborkman@redhat.com> CC: Willem de Bruijn <willemb@google.com> CC: Phil Sutter <phil@nwl.cc> CC: Eric Dumazet <edumazet@google.com> Reported-by:
Jan Stancek <jstancek@redhat.com> Tested-by:
Veaceslav Falico <vfalico@redhat.com> Acked-by:
Daniel Borkmann <dborkman@redhat.com> Signed-off-by:
-
Daniel Borkmann authored
[ Upstream commit e40526cb ] Salam reported a use after free bug in PF_PACKET that occurs when we're sending out frames on a socket bound device and suddenly the net device is being unregistered. It appears that commit 827d9780 introduced a possible race condition between {t,}packet_snd() and packet_notifier(). In the case of a bound socket, packet_notifier() can drop the last reference to the net_device and {t,}packet_snd() might end up suddenly sending a packet over a freed net_device. To avoid reverting 827d9780 and thus introducing a performance regression compared to the current state of things, we decided to hold a cached RCU protected pointer to the net device and maintain it on write side via bind spin_lock protected register_prot_hook() and __unregister_prot_hook() calls. In {t,}packet_snd() path, we access this pointer under rcu_read_lock through packet_cached_dev_get() that holds reference to the device to prevent it from being freed through packet_notifier() while we're in send path. This is okay to do as dev_put()/dev_hold() are per-cpu counters, so this should not be a performance issue. Also, the code simplifies a bit as we don't need need_rls_dev anymore. Fixes: 827d9780 ("af-packet: Use existing netdev reference for bound sockets.") Reported-by:
Salam Noureddine <noureddine@aristanetworks.com> Signed-off-by:
-
Ding Tianhong authored
[ Upstream commit f8730420 ] When the following commands are executed: brctl addbr br0 ifconfig br0 hw ether <addr> rmmod bridge The calltrace will occur: [ 563.312114] device eth1 left promiscuous mode [ 563.312188] br0: port 1(eth1) entered disabled state [ 563.468190] kmem_cache_destroy bridge_fdb_cache: Slab cache still has objects [ 563.468197] CPU: 6 PID: 6982 Comm: rmmod Tainted: G O 3.12.0-0.7-default+ #9 [ 563.468199] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2007 [ 563.468200] 0000000000000880 ffff88010f111e98 ffffffff814d1c92 ffff88010f111eb8 [ 563.468204] ffffffff81148efd ffff88010f111eb8 0000000000000000 ffff88010f111ec8 [ 563.468206] ffffffffa062a270 ffff88010f111ed8 ffffffffa063ac76 ffff88010f111f78 [ 563.468209] Call Trace: [ 563.468218] [<ffffffff814d1c92>] dump_stack+0x6a/0x78 [ 563.468234] [<ffffffff81148efd>] kmem_cache_destroy+0xfd/0x100 [ 563.468242] [<ffffffffa062a270>] br_fdb_fini+0x10/0x20 [bridge] [ 563.468247] [<ffffffffa063ac76>] br_deinit+0x4e/0x50 [bridge] [ 563.468254] [<ffffffff810c7dc9>] SyS_delete_module+0x199/0x2b0 [ 563.468259] [<ffffffff814e0922>] system_call_fastpath+0x16/0x1b [ 570.377958] Bridge firewalling registered --------------------------- cut here ------------------------------- The reason is that when the bridge dev's address is changed, the br_fdb_change_mac_address() will add new address in fdb, but when the bridge was removed, the address entry in the fdb did not free, the bridge_fdb_cache still has objects when destroy the cache, Fix this by flushing the bridge address entry when removing the bridge. v2: according to the Toshiaki Makita and Vlad's suggestion, I only delete the vlan0 entry, it still have a leak here if the vlan id is other number, so I need to call fdb_delete_by_port(br, NULL, 1) to flush all entries whose dst is NULL for the bridge. Suggested-by:
Toshiaki Makita <toshiaki.makita1@gmail.com> Suggested-by:
Vlad Yasevich <vyasevich@gmail.com> Signed-off-by:
Ding Tianhong <dingtianhong@huawei.com> Signed-off-by:
-
Vlad Yasevich authored
[ Upstream commit d2615bf4 ] The following commit: b6c40d68 net: only invoke dev->change_rx_flags when device is UP tried to fix a problem with VLAN devices and promiscuouse flag setting. The issue was that VLAN device was setting a flag on an interface that was down, thus resulting in bad promiscuity count. This commit blocked flag propagation to any device that is currently down. A later commit: deede2fa vlan: Don't propagate flag changes on down interfaces fixed VLAN code to only propagate flags when the VLAN interface is up, thus fixing the same issue as above, only localized to VLAN. The problem we have now is that if we have create a complex stack involving multiple software devices like bridges, bonds, and vlans, then it is possible that the flags would not propagate properly to the physical devices. A simple examle of the scenario is the following: eth0----> bond0 ----> bridge0 ---> vlan50 If bond0 or eth0 happen to be down at the time bond0 is added to the bridge, then eth0 will never have promisc mode set which is currently required for operation as part of the bridge. As a result, packets with vlan50 will be dropped by the interface. The only 2 devices that implement the special flag handling are VLAN and DSA and they both have required code to prevent incorrect flag propagation. As a result we can remove the generic solution introduced in b6c40d68 and leave it to the individual devices to decide whether they will block flag propagation or not. Reported-by:
Stefan Priebe <s.priebe@profihost.ag> Suggested-by:
Vlad Yasevich <vyasevic@redhat.com> Signed-off-by:
-
Ying Xue authored
[ Upstream commit b5de4a22 ] init_card() calls dev_get_by_name() to get a network deceive. But it doesn't decrease network device reference count after the device is used. Signed-off-by:
Ying Xue <ying.xue@windriver.com> Signed-off-by:
-
Hannes Frederic Sowa authored
[ Upstream commit 1fa4c710 ] Offenders don't have port numbers, so set it to 0. Signed-off-by:
-
Dan Carpenter authored
[ Upstream commit db31c55a ] If kmsg->msg_namelen > sizeof(struct sockaddr_storage) then in the original code that would lead to memory corruption in the kernel if you had audit configured. If you didn't have audit configured it was harmless. There are some programs such as beta versions of Ruby which use too large of a buffer and returning an error code breaks them. We should clamp the ->msg_namelen value instead. Fixes: 1661bf36 ("net: heap overflow in __audit_sockaddr()") Reported-by:
Eric Wong <normalperson@yhbt.net> Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Tested-by:
-
Hannes Frederic Sowa authored
[ Upstream commit 85fbaa75 ] Commit bceaa902 ("inet: prevent leakage of uninitialized memory to user in recv syscalls") conditionally updated addr_len if the msg_name is written to. The recv_error and rxpmtu functions relied on the recvmsg functions to set up addr_len before. As this does not happen any more we have to pass addr_len to those functions as well and set it to the size of the corresponding sockaddr length. This broke traceroute and such. Fixes: bceaa902 ("inet: prevent leakage of uninitialized memory to user in recv syscalls") Reported-by:
Brad Spengler <spender@grsecurity.net> Reported-by: Tom Labanowski Cc: mpb <mpb.mail@gmail.com> Cc: David S. Miller <davem@davemloft.net> Cc: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by:
-
Hannes Frederic Sowa authored
[ Upstream commit 68c6beb3 ] In that case it is probable that kernel code overwrote part of the stack. So we should bail out loudly here. The BUG_ON may be removed in future if we are sure all protocols are conformant. Suggested-by:
Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by:
-
Hannes Frederic Sowa authored
[ Upstream commit f3d33426 ] This patch now always passes msg->msg_namelen as 0. recvmsg handlers must set msg_namelen to the proper size <= sizeof(struct sockaddr_storage) to return msg_name to the user. This prevents numerous uninitialized memory leaks we had in the recvmsg handlers and makes it harder for new code to accidentally leak uninitialized memory. Optimize for the case recvfrom is called with NULL as address. We don't need to copy the address at all, so set it to NULL before invoking the recvmsg handler. We can do so, because all the recvmsg handlers must cope with the case a plain read() is called on them. read() also sets msg_name to NULL. Also document these changes in include/linux/net.h as suggested by David Miller. Changes since RFC: Set msg->msg_name = NULL if user specified a NULL in msg_name but had a non-null msg_namelen in verify_iovec/verify_compat_iovec. This doesn't affect sendto as it would bail out earlier while trying to copy-in the address. It also more naturally reflects the logic by the callers of verify_iovec. With this change in place I could remove " if (!uaddr || msg_sys->msg_namelen == 0) msg->msg_name = NULL ". This change does not alter the user visible error logic as we ignore msg_namelen as long as msg_name is NULL. Also remove two unnecessary curly brackets in ___sys_recvmsg and change comments to netdev style. Cc: David Miller <davem@davemloft.net> Suggested-by:
-
Hannes Frederic Sowa authored
[ Upstream commit bceaa902 ] Only update *addr_len when we actually fill in sockaddr, otherwise we can return uninitialized memory from the stack to the caller in the recvfrom, recvmmsg and recvmsg syscalls. Drop the the (addr_len == NULL) checks because we only get called with a valid addr_len pointer either from sock_common_recvmsg or inet_recvmsg. If a blocking read waits on a socket which is concurrently shut down we now return zero and set msg_msgnamelen to 0. Reported-by:
mpb <mpb.mail@gmail.com> Suggested-by:
-
Eric Dumazet authored
[ Upstream commit c9e90429 ] ip4_datagram_connect() being called from process context, it should use IP_INC_STATS() instead of IP_INC_STATS_BH() otherwise we can deadlock on 32bit arches, or get corruptions of SNMP counters. Fixes: 584bdf8c ("[IPV4]: Fix "ipOutNoRoutes" counter error for TCP and UDP") Signed-off-by:
Dave Jones <davej@redhat.com> Signed-off-by:
-
Chris Metcalf authored
[ Upstream commit 1ca1a4cf ] In af3e095a, Erik Jacobsen fixed one type of unaligned access bug for ia64 by converting a 64-bit write to use put_unaligned(). Unfortunately, since gcc will convert a short memset() to a series of appropriately-aligned stores, the problem is now visible again on tilegx, where the memset that zeros out proc_event is converted to three 64-bit stores, causing an unaligned access panic. A better fix for the original problem is to ensure that proc_event is aligned to 8 bytes here. We can do that relatively easily by arranging to start the struct cn_msg aligned to 8 bytes and then offset by 4 bytes. Doing so means that the immediately following proc_event structure is then correctly aligned to 8 bytes. The result is that the memset() stores are now aligned, and as an added benefit, we can remove the put_unaligned() calls in the code. Signed-off-by:
Chris Metcalf <cmetcalf@tilera.com> Signed-off-by:
-
Dan Carpenter authored
[ Upstream commit f9a23c84 ] These strings come from a copy_from_user() and there is no way to be sure they are NUL terminated. Signed-off-by:
-
Nikolay Aleksandrov authored
[ Upstream commit b869ccfa ] This patch fixes two race conditions between bond_store_updelay/downdelay and bond_store_miimon which could lead to division by zero as miimon can be set to 0 while either updelay/downdelay are being set and thus miss the zero check in the beginning, the zero div happens because updelay/downdelay are stored as new_value / bond->params.miimon. Use rtnl to synchronize with miimon setting. Signed-off-by:
Nikolay Aleksandrov <nikolay@redhat.com> CC: Jay Vosburgh <fubar@us.ibm.com> CC: Andy Gospodarek <andy@greyhouse.net> CC: Veaceslav Falico <vfalico@redhat.com> Acked-by:
-
Jukka Rissanen authored
[ Upstream commit 1188f054 ] If priority/traffic class field in IPv6 header is set (seen when using ssh), the uncompression sets the TC and Flow fields incorrectly. Example: This is IPv6 header of a sent packet. Note the priority/TC (=1) in the first byte. 00000000: 61 00 00 00 00 2c 06 40 fe 80 00 00 00 00 00 00 00000010: 02 02 72 ff fe c6 42 10 fe 80 00 00 00 00 00 00 00000020: 02 1e ab ff fe 4c 52 57 This gets compressed like this in the sending side 00000000: 72 31 04 06 02 1e ab ff fe 4c 52 57 ec c2 00 16 00000010: aa 2d fe 92 86 4e be c6 .... In the receiving end, the packet gets uncompressed to this IPv6 header 00000000: 60 06 06 02 00 2a 1e 40 fe 80 00 00 00 00 00 00 00000010: 02 02 72 ff fe c6 42 10 fe 80 00 00 00 00 00 00 00000020: ab ff fe 4c 52 57 ec c2 First four bytes are set incorrectly and we have also lost two bytes from destination address. The fix is to switch the case values in switch statement when checking the TC field. Signed-off-by:
Jukka Rissanen <jukka.rissanen@linux.intel.com> Signed-off-by:
-
Veaceslav Falico authored
[ Upstream commit ec9f1d15 ] Currently the ARP monitoring is not supported with 802.3ad, and it's prohibited to use it via the module params. However we still can set it afterwards via sysfs, cause we only check for *LB modes there. To fix this - add a check for 802.3ad mode in bonding_store_arp_interval. Signed-off-by:
-
Daniel Borkmann authored
[ Upstream commit 51c37a70 ] For properly initialising the Tausworthe generator [1], we have a strict seeding requirement, that is, s1 > 1, s2 > 7, s3 > 15. Commit 697f8d03 ("random32: seeding improvement") introduced a __seed() function that imposes boundary checks proposed by the errata paper [2] to properly ensure above conditions. However, we're off by one, as the function is implemented as: "return (x < m) ? x + m : x;", and called with __seed(X, 1), __seed(X, 7), __seed(X, 15). Thus, an unwanted seed of 1, 7, 15 would be possible, whereas the lower boundary should actually be of at least 2, 8, 16, just as GSL does. Fix this, as otherwise an initialization with an unwanted seed could have the effect that Tausworthe's PRNG properties cannot not be ensured. Note that this PRNG is *not* used for cryptography in the kernel. [1] http://www.iro.umontreal.ca/~lecuyer/myftp/papers/tausme.ps [2] http://www.iro.umontreal.ca/~lecuyer/myftp/papers/tausme2.ps Joint work with Hannes Frederic Sowa. Fixes: 697f8d03 ("random32: seeding improvement") Cc: Stephen Hemminger <stephen@networkplumber.org> Cc: Florian Weimer <fweimer@redhat.com> Cc: Theodore Ts'o <tytso@mit.edu> Signed-off-by:
-
Duan Jiong authored
[ Upstream commit f104a567 ] As the rfc 4191 said, the Router Preference and Lifetime values in a ::/0 Route Information Option should override the preference and lifetime values in the Router Advertisement header. But when the kernel deals with a ::/0 Route Information Option, the rt6_get_route_info() always return NULL, that means that overriding will not happen, because those default routers were added without flag RTF_ROUTEINFO in rt6_add_dflt_router(). In order to deal with that condition, we should call rt6_get_dflt_router when the prefix length is 0. Signed-off-by:
Duan Jiong <duanj.fnst@cn.fujitsu.com> Acked-by:
-
Andreas Henriksson authored
[ Upstream commit 13eb2ab2 ] When trying to delete a table >= 256 using iproute2 the local table will be deleted. The table id is specified as a netlink attribute when it needs more then 8 bits and iproute2 then sets the table field to RT_TABLE_UNSPEC (0). Preconditions to matching the table id in the rule delete code doesn't seem to take the "table id in netlink attribute" into condition so the frh_get_table helper function never gets to do its job when matching against current rule. Use the helper function twice instead of peaking at the table value directly. Originally reported at: http://bugs.debian.org/724783Reported-by:
Nicolas HICHER <nhicher@avencall.com> Signed-off-by:
Andreas Henriksson <andreas@fatal.se> Signed-off-by:
-
- 04 Dec, 2013 14 commits
-
-
Greg Kroah-Hartman authored
-
Nanno Langstraat authored
commit 43c83146 upstream. Use case: people who use both Apple and PC keyboards regularly, and desire to keep&use their PC muscle memory. A particular use case: an Apple compact external keyboard connected to a PC laptop. (This use case can't be covered well by X.org key remappings etc.) Signed-off-by:
Nanno Langstraat <langstr@gmail.com> Signed-off-by:
-
Stefan Achatz authored
commit 7be63f20 upstream. Add missing switch breaks. Signed-off-by:
Stefan Achatz <erazor_de@users.sourceforge.net> Signed-off-by:
-
Mauro Carvalho Chehab authored
commit ac5b4b6b upstream. Dynamic static allocation is evil, as Kernel stack is too low, and ompilation complains about it on some archs: drivers/staging/media/lirc/lirc_zilog.c:967:1: warning: 'read' uses dynamic stack allocation [enabled by default] Instead, let's enforce a limit for the buffer to be 64. That should be more than enough. Signed-off-by:
Mauro Carvalho Chehab <m.chehab@samsung.com> Reviewed-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
-
Steven Rostedt (Red Hat) authored
commit 8a56d776 upstream. Commit 8c4f3c3f "ftrace: Check module functions being traced on reload" fixed module loading and unloading with respect to function tracing, but it missed the function graph tracer. If you perform the following # cd /sys/kernel/debug/tracing # echo function_graph > current_tracer # modprobe nfsd # echo nop > current_tracer You'll get the following oops message: ------------[ cut here ]------------ WARNING: CPU: 2 PID: 2910 at /linux.git/kernel/trace/ftrace.c:1640 __ftrace_hash_rec_update.part.35+0x168/0x1b9() Modules linked in: nfsd exportfs nfs_acl lockd ipt_MASQUERADE sunrpc ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ipv6 ip6table_filter ip6_tables uinput snd_hda_codec_idt CPU: 2 PID: 2910 Comm: bash Not tainted 3.13.0-rc1-test #7 Hardware name: To Be Filled By O.E.M. To Be Filled By O.E.M./To be filled by O.E.M., BIOS SDBLI944.86P 05/08/2007 0000000000000668 ffff8800787efcf8 ffffffff814fe193 ffff88007d500000 0000000000000000 ffff8800787efd38 ffffffff8103b80a 0000000000000668 ffffffff810b2b9a ffffffff81a48370 0000000000000001 ffff880037aea000 Call Trace: [<ffffffff814fe193>] dump_stack+0x4f/0x7c [<ffffffff8103b80a>] warn_slowpath_common+0x81/0x9b [<ffffffff810b2b9a>] ? __ftrace_hash_rec_update.part.35+0x168/0x1b9 [<ffffffff8103b83e>] warn_slowpath_null+0x1a/0x1c [<ffffffff810b2b9a>] __ftrace_hash_rec_update.part.35+0x168/0x1b9 [<ffffffff81502f89>] ? __mutex_lock_slowpath+0x364/0x364 [<ffffffff810b2cc2>] ftrace_shutdown+0xd7/0x12b [<ffffffff810b47f0>] unregister_ftrace_graph+0x49/0x78 [<ffffffff810c4b30>] graph_trace_reset+0xe/0x10 [<ffffffff810bf393>] tracing_set_tracer+0xa7/0x26a [<ffffffff810bf5e1>] tracing_set_trace_write+0x8b/0xbd [<ffffffff810c501c>] ? ftrace_return_to_handler+0xb2/0xde [<ffffffff811240a8>] ? __sb_end_write+0x5e/0x5e [<ffffffff81122aed>] vfs_write+0xab/0xf6 [<ffffffff8150a185>] ftrace_graph_caller+0x85/0x85 [<ffffffff81122dbd>] SyS_write+0x59/0x82 [<ffffffff8150a185>] ftrace_graph_caller+0x85/0x85 [<ffffffff8150a2d2>] system_call_fastpath+0x16/0x1b ---[ end trace 940358030751eafb ]--- The above mentioned commit didn't go far enough. Well, it covered the function tracer by adding checks in __register_ftrace_function(). The problem is that the function graph tracer circumvents that (for a slight efficiency gain when function graph trace is running with a function tracer. The gain was not worth this). The problem came with ftrace_startup() which should always be called after __register_ftrace_function(), if you want this bug to be completely fixed. Anyway, this solution moves __register_ftrace_function() inside of ftrace_startup() and removes the need to call them both. Reported-by:
Dave Wysochanski <dwysocha@redhat.com> Fixes: ed926f9b ("ftrace: Use counters to enable functions to trace") Signed-off-by:
Steven Rostedt <rostedt@goodmis.org> Signed-off-by:
-
Alex Williamson authored
commit e40f193f upstream. The iommu integration into memory slots expects memory slots to be added or removed and doesn't handle the move case. We can unmap slots from the iommu after we mark them invalid and map them before installing the final memslot array. Also re-order the kmemdup vs map so we don't leave iommu mappings if we get ENOMEM. Reviewed-by:
Gleb Natapov <gleb@redhat.com> Signed-off-by:
Alex Williamson <alex.williamson@redhat.com> Signed-off-by:
Marcelo Tosatti <mtosatti@redhat.com> Cc: Luis Henriques <luis.henriques@canonical.com> Signed-off-by:
-
Marcelo Tosatti authored
commit 12d6e753 upstream. PPC must flush all translations before the new memory slot is visible. Signed-off-by:
Avi Kivity <avi@redhat.com> Cc: Luis Henriques <luis.henriques@canonical.com> Signed-off-by:
-
Tom Gundersen authored
commit 78551277 upstream. This allows the module to be autoloaded in the common case. In order to work on non-PnP systems the module should be compiled in or loaded unconditionally at boot (c.f. modules-load.d(5)), as before. Signed-off-by:
Tom Gundersen <teg@jklm.no> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Steven Rostedt (Red Hat) authored
commit 4e58e547 upstream. If an TRACE_EVENT() uses __assign_str() or __get_str on a NULL pointer then the following oops will happen: BUG: unable to handle kernel NULL pointer dereference at (null) IP: [<c127a17b>] strlen+0x10/0x1a *pde = 00000000 ^M Oops: 0000 [#1] PREEMPT SMP Modules linked in: CPU: 1 PID: 0 Comm: swapper/1 Not tainted 3.13.0-rc1-test+ #2 Hardware name: /DG965MQ, BIOS MQ96510J.86A.0372.2006.0605.1717 06/05/2006^M task: f5cde9f0 ti: f5e5e000 task.ti: f5e5e000 EIP: 0060:[<c127a17b>] EFLAGS: 00210046 CPU: 1 EIP is at strlen+0x10/0x1a EAX: 00000000 EBX: c2472da8 ECX: ffffffff EDX: c2472da8 ESI: c1c5e5fc EDI: 00000000 EBP: f5e5fe84 ESP: f5e5fe80 DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068 CR0: 8005003b CR2: 00000000 CR3: 01f32000 CR4: 000007d0 Stack: f5f18b90 f5e5feb8 c10687a8 0759004f 00000005 00000005 00000005 00200046 00000002 00000000 c1082a93 f56c7e28 c2472da8 c1082a93 f5e5fee4 c106bc61^M 00000000 c1082a93 00000000 00000000 00000001 00200046 00200082 00000000 Call Trace: [<c10687a8>] ftrace_raw_event_lock+0x39/0xc0 [<c1082a93>] ? ktime_get+0x29/0x69 [<c1082a93>] ? ktime_get+0x29/0x69 [<c106bc61>] lock_release+0x57/0x1a5 [<c1082a93>] ? ktime_get+0x29/0x69 [<c10824dd>] read_seqcount_begin.constprop.7+0x4d/0x75 [<c1082a93>] ? ktime_get+0x29/0x69^M [<c1082a93>] ktime_get+0x29/0x69 [<c108a46a>] __tick_nohz_idle_enter+0x1e/0x426 [<c10690e8>] ? lock_release_holdtime.part.19+0x48/0x4d [<c10bc184>] ? time_hardirqs_off+0xe/0x28 [<c1068c82>] ? trace_hardirqs_off_caller+0x3f/0xaf [<c108a8cb>] tick_nohz_idle_enter+0x59/0x62 [<c1079242>] cpu_startup_entry+0x64/0x192 [<c102299c>] start_secondary+0x277/0x27c Code: 90 89 c6 89 d0 88 c4 ac 38 e0 74 09 84 c0 75 f7 be 01 00 00 00 89 f0 48 5e 5d c3 55 89 e5 57 66 66 66 66 90 83 c9 ff 89 c7 31 c0 <f2> ae f7 d1 8d 41 ff 5f 5d c3 55 89 e5 57 66 66 66 66 90 31 ff EIP: [<c127a17b>] strlen+0x10/0x1a SS:ESP 0068:f5e5fe80 CR2: 0000000000000000 ---[ end trace 01bc47bf519ec1b2 ]--- New tracepoints have been added that have allowed for NULL pointers being assigned to strings. To fix this, change the TRACE_EVENT() code to check for NULL and if it is, it will assign "(null)" to it instead (similar to what glibc printf does). Reported-by:
Shuah Khan <shuah.kh@samsung.com> Reported-by:
Jovi Zhangwei <jovi.zhangwei@gmail.com> Link: http://lkml.kernel.org/r/CAGdX0WFeEuy+DtpsJzyzn0343qEEjLX97+o1VREFkUEhndC+5Q@mail.gmail.com Link: http://lkml.kernel.org/r/528D6972.9010702@samsung.com Fixes: 9cbf1176 ("tracing/events: provide string with undefined size support") Signed-off-by:
-
Kailang Yang authored
commit 9ad54547 upstream. Set the missing pcbeep default amp for ALC668. Signed-off-by:
Kailang Yang <kailang@realtek.com> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Peter Zijlstra authored
commit 0fc0287c upstream. Juri hit the below lockdep report: [ 4.303391] ====================================================== [ 4.303392] [ INFO: SOFTIRQ-safe -> SOFTIRQ-unsafe lock order detected ] [ 4.303394] 3.12.0-dl-peterz+ #144 Not tainted [ 4.303395] ------------------------------------------------------ [ 4.303397] kworker/u4:3/689 [HC0[0]:SC0[0]:HE0:SE1] is trying to acquire: [ 4.303399] (&p->mems_allowed_seq){+.+...}, at: [<ffffffff8114e63c>] new_slab+0x6c/0x290 [ 4.303417] [ 4.303417] and this task is already holding: [ 4.303418] (&(&q->__queue_lock)->rlock){..-...}, at: [<ffffffff812d2dfb>] blk_execute_rq_nowait+0x5b/0x100 [ 4.303431] which would create a new lock dependency: [ 4.303432] (&(&q->__queue_lock)->rlock){..-...} -> (&p->mems_allowed_seq){+.+...} [ 4.303436] [ 4.303898] the dependencies between the lock to be acquired and SOFTIRQ-irq-unsafe lock: [ 4.303918] -> (&p->mems_allowed_seq){+.+...} ops: 2762 { [ 4.303922] HARDIRQ-ON-W at: [ 4.303923] [<ffffffff8108ab9a>] __lock_acquire+0x65a/0x1ff0 [ 4.303926] [<ffffffff8108cbe3>] lock_acquire+0x93/0x140 [ 4.303929] [<ffffffff81063dd6>] kthreadd+0x86/0x180 [ 4.303931] [<ffffffff816ded6c>] ret_from_fork+0x7c/0xb0 [ 4.303933] SOFTIRQ-ON-W at: [ 4.303933] [<ffffffff8108abcc>] __lock_acquire+0x68c/0x1ff0 [ 4.303935] [<ffffffff8108cbe3>] lock_acquire+0x93/0x140 [ 4.303940] [<ffffffff81063dd6>] kthreadd+0x86/0x180 [ 4.303955] [<ffffffff816ded6c>] ret_from_fork+0x7c/0xb0 [ 4.303959] INITIAL USE at: [ 4.303960] [<ffffffff8108a884>] __lock_acquire+0x344/0x1ff0 [ 4.303963] [<ffffffff8108cbe3>] lock_acquire+0x93/0x140 [ 4.303966] [<ffffffff81063dd6>] kthreadd+0x86/0x180 [ 4.303969] [<ffffffff816ded6c>] ret_from_fork+0x7c/0xb0 [ 4.303972] } Which reports that we take mems_allowed_seq with interrupts enabled. A little digging found that this can only be from cpuset_change_task_nodemask(). This is an actual deadlock because an interrupt doing an allocation will hit get_mems_allowed()->...->__read_seqcount_begin(), which will spin forever waiting for the write side to complete. Cc: John Stultz <john.stultz@linaro.org> Cc: Mel Gorman <mgorman@suse.de> Reported-by:
Juri Lelli <juri.lelli@gmail.com> Signed-off-by:
Peter Zijlstra <peterz@infradead.org> Tested-by:
Li Zefan <lizefan@huawei.com> Acked-by:
Mel Gorman <mgorman@suse.de> Signed-off-by:
Tejun Heo <tj@kernel.org> Signed-off-by:
-
Michael Neuling authored
commit ec67ad82 upstream. In a recent patch: commit c13f20ac Author: Michael Neuling <mikey@neuling.org> powerpc/signals: Mark VSX not saved with small contexts We fixed an issue but an improved solution was later discussed after the patch was merged. Firstly, this patch doesn't handle the 64bit signals case, which could also hit this issue (but has never been reported). Secondly, the original patch isn't clear what MSR VSX should be set to. The new approach below always clears the MSR VSX bit (to indicate no VSX is in the context) and sets it only in the specific case where VSX is available (ie. when VSX has been used and the signal context passed has space to provide the state). This reverts the original patch and replaces it with the improved solution. It also adds a 64 bit version. Signed-off-by:
Michael Neuling <mikey@neuling.org> Signed-off-by:
Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by:
-
NeilBrown authored
commit 02e5f5c0 upstream. The various ->run routines of md personalities assume that the 'queue' has been initialised by the blk_set_stacking_limits() call in md_alloc(). However when the level is changed (by level_store()) the ->run routine for the new level is called for an array which has already had the stacking limits modified. This can result in incorrect final settings. So call blk_set_stacking_limits() before ->run in level_store(). A specific consequence of this bug is that it causes discard_granularity to be set incorrectly when reshaping a RAID4 to a RAID0. This is suitable for any -stable kernel since 3.3 in which blk_set_stacking_limits() was introduced. Reported-and-tested-by:
"Baldysiak, Pawel" <pawel.baldysiak@intel.com> Signed-off-by:
NeilBrown <neilb@suse.de> Signed-off-by:
-
Jerome Glisse authored
commit 97b6ff6b upstream. GPU with low amount of ram can fails at pinning new framebuffer before unpinning old one. On such failure, retry with unpinning old one before pinning new one allowing to work around the issue. This is somewhat ugly but only affect those old GPU we care about. Signed-off-by:
Jerome Glisse <jglisse@redhat.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
