On i.MX8MM, we are running Dual Linux OS, with 1st Linux using SD Card
as rootfs storage, 2nd Linux using eMMC as rootfs storage. We let the
the 1st linux configure power/clock for the 2nd Linux.

When the 2nd Linux is booting into rootfs stage, we let the 1st Linux
to destroy the 2nd linux, then restart the 2nd linux, we met SDHCI dump
as following, after we clear the pending interrupt and halt CQCTL, issue
gone.

[ 1.334594] mmc2: Got command interrupt 0x00000001 even though no command operation was in progress.
[ 1.334595] mmc2: sdhci: ============ SDHCI REGISTER DUMP ===========
[ 1.334599] mmc2: sdhci: Sys addr: 0xa05dcc00 | Version: 0x00000002
[ 1.345538] mmc2: sdhci: Blk size: 0x00000200 | Blk cnt: 0x00000000
[ 1.345541] mmc2: sdhci: Argument: 0x00018000 | Trn mode: 0x00000033
[ 1.345543] mmc2: sdhci: Present: 0x01f88008 | Host ctl: 0x00000031
[ 1.345547] mmc2: sdhci: Power: 0x00000002 | Blk gap: 0x00000080
[ 1.357903] mmc2: sdhci: Wake-up: 0x00000008 | Clock: 0x0000003f
[ 1.357905] mmc2: sdhci: Timeout: 0x0000008f | Int stat: 0x00000000
[ 1.357908] mmc2: sdhci: Int enab: 0x107f100b | Sig enab: 0x107f100b
[ 1.357911] mmc2: sdhci: AC12 err: 0x00000000 | Slot int: 0x00000502
[ 1.370268] mmc2: sdhci: Caps: 0x07eb0000 | Caps_1: 0x0000b400
[ 1.370270] mmc2: sdhci: Cmd: 0x00000d1a | Max curr: 0x00ffffff
[ 1.370273] mmc2: sdhci: Resp[0]: 0x00000b00 | Resp[1]: 0xffffffff
[ 1.370276] mmc2: sdhci: Resp[2]: 0x328f5903 | Resp[3]: 0x00d00f00
[ 1.382132] mmc2: sdhci: Host ctl2: 0x00000000
[ 1.382135] mmc2: sdhci: ADMA Err: 0x00000000 | ADMA Ptr: 0xa2040208

[ 2.060932] mmc2: Unexpected interrupt 0x00004000.
[ 2.065538] mmc2: sdhci: ============ SDHCI REGISTER DUMP ===========
[ 2.071720] mmc2: sdhci: Sys addr: 0x00000000 | Version: 0x00000002
[ 2.077902] mmc2: sdhci: Blk size: 0x00000200 | Blk cnt: 0x00000001
[ 2.084083] mmc2: sdhci: Argument: 0x00000000 | Trn mode: 0x00000000
[ 2.090264] mmc2: sdhci: Present: 0x01f88009 | Host ctl: 0x00000011
[ 2.096446] mmc2: sdhci: Power: 0x00000002 | Blk gap: 0x00000080
[ 2.102627] mmc2: sdhci: Wake-up: 0x00000008 | Clock: 0x000010ff
[ 2.108809] mmc2: sdhci: Timeout: 0x0000008f | Int stat: 0x00004000
[ 2.114990] mmc2: sdhci: Int enab: 0x007f1003 | Sig enab: 0x007f1003
[ 2.121171] mmc2: sdhci: AC12 err: 0x00000000 | Slot int: 0x00000502
[ 2.127353] mmc2: sdhci: Caps: 0x07eb0000 | Caps_1: 0x0000b400
[ 2.133534] mmc2: sdhci: Cmd: 0x0000371a | Max curr: 0x00ffffff
[ 2.139715] mmc2: sdhci: Resp[0]: 0x00000900 | Resp[1]: 0xffffffff
[ 2.145896] mmc2: sdhci: Resp[2]: 0x328f5903 | Resp[3]: 0x00d00f00
[ 2.152077] mmc2: sdhci: Host ctl2: 0x00000000
[ 2.156342] mmc2: sdhci: ADMA Err: 0x00000000 | ADMA Ptr: 0x00000000
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1582100757-20683-6-git-send-email-haibo.chen@nxp.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add new esdhc_soc_data, with compatible string "fsl,imx8mm-usdhc".
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1582100757-20683-5-git-send-email-haibo.chen@nxp.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Since L4.15, community involve the commit 105819c8 ("mmc: core: use mrq->sbc
when sending CMD23 for RPMB"), let the usdhc to decide whether to use ACMD23 for
RPMB. This CMD23 for RPMB need to set the bit 31 to its argument, if not, the
RPMB write operation will return general fail.

According to the sdhci logic, SDMA mode will disable the ACMD23, and only in
ADMA mode, it will chose to use ACMD23 if the host support. But according to
debug, and confirm with IC, the imx6qpdl/imx6sx/imx6sl/imx7d do not support
the ACMD23 feature completely. These SoCs only use the 16 bit block count of
the register 0x4 (BLOCK_ATT) as the CMD23's argument in ACMD23 mode, which
means it will ignore the upper 16 bit of the CMD23's argument. This will block
the reliable write operation in RPMB, because RPMB reliable write need to set
the bit31 of the CMD23's argument. This is the hardware limitation. So for
imx6qpdl/imx6sx/imx6sl/imx7d, it need to broke the ACMD23 for eMMC, SD card do
not has this limitation, because SD card do not support reliable write.

For imx6ul/imx6ull/imx6sll/imx7ulp/imx8, it support the ACMD23 completely, it
change to use the 0x0 register (DS_ADDR) to put the CMD23's argument in ADMA mode.

This patch add a new flag ESDHC_FLAG_BROKEN_AUTO_CMD23, and add this flag to
imx6q/imx6sx/imx6sl/imx7d, and due to the imx6sll share the same compatible string
with imx6sx before, and imx6sll do not has this limitation, so add a new compatible
string for imx6sll.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1582100757-20683-4-git-send-email-haibo.chen@nxp.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

After set the STROBE SLV delay target value, it need to wait some
time to let the usdhc lock the REF and SLV clock. In normal case,
1~2us is enough for imx8/imx6 and imx7d, and 4~5us is enough for
imx7ulp, but when do reboot stress test or do the bind/unbind stress
test, sometimes need to wait about 10us to get the status lock.

This patch optimize delay handle method, only print the warning
message if the status is still not lock after 1ms delay.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1582100757-20683-3-git-send-email-haibo.chen@nxp.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

When force clock off, check the SDOFF of register PRSSTAT to make sure
the clock is gate off. Before force clock on, check the SDSTB of register
PRSSTAT to make sure the clock is stable, this will eliminate the clock
glitch.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1582100757-20683-2-git-send-email-haibo.chen@nxp.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

strobe-dll-delay-target is the delay cell add on the strobe line.
Strobe line the the uSDHC loopback read clock which is use in HS400
mode. Different strobe-dll-delay-target may need to set for different
board/SoC. If this delay cell is not set to an appropriate value,
we may see some read operation meet CRC error after HS400 mode select
which already pass the tuning.

This patch add the strobe-dll-delay-target setting in driver, so that
user can easily config this delay cell in dts file.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1582100757-20683-1-git-send-email-haibo.chen@nxp.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

When pm_runtime_suspend is run, a call to SCFW power off the SS (SS is a
power domain, usdhc belong to this SS power domain) in which the resource
resides is made. The SCFW can power off the SS if no other resource in
active in that SS. If so, all state associated with all the resources within
the SS that is powered off is lost, this includes the clock rates, clock state
etc. When pm_runtime_resume is called, the SS associated with that resource
is powered up. But the clocks are left in the default state.

This patch restore clock rate in pm_runtime_resume, make sure the
clock is right rather than depending on the default state setting
by SCFW.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1582100563-20555-5-git-send-email-haibo.chen@nxp.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

For Mega/Mix enabled SoCs like MX7D and MX6SX, uSDHC will lost power in
LP mode no matter whether the MMC_KEEP_POWER flag is set or not.
This may cause state misalign between kernel and HW, especially for
SDIO3.0 WiFi cards.
e.g. SDIO WiFi driver usually will keep power during system suspend.
And after resume, no card re-enumeration called.
But the tuning state is lost due to Mega/Mix.
Then CRC error may happen during next data transfer.

So we should always fire a mmc_retune_needed() for such type SoC
to tell MMC core retuning is needed for next data transfer.
mmc: sdhci-esdhci-imx: retune needed for Mega/Mix enabled SoCs
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1582100563-20555-4-git-send-email-haibo.chen@nxp.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

When using jailhouse to support two Linux on i.MX8MQ EVK, we use the
1st Linux to configure pinctrl for the 2nd Linux. Then the 2nd Linux
could use the mmc without pinctrl driver.

So give a warning message when no pinctrl available, but no fail probe.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/1582100563-20555-3-git-send-email-haibo.chen@nxp.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Now that invert_gpio arguments are unused, let's remove them.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Link: https://lore.kernel.org/r/64d766d1f8af2e22bce32f4ffa453f7234207ad6.1576031637.git.mirq-linux@rere.qmqm.plSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Use MMC_CAP2_RO_ACTIVE_HIGH flag as indicator if GPIO line is to be
inverted compared to DT/platform-specified polarity. The flag is not used
after init in GPIO mode anyway. No functional changes intended.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Link: https://lore.kernel.org/r/a60f563f11bbff821da2fa2949ca82922b144860.1576031637.git.mirq-linux@rere.qmqm.plSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Let's drop the boilerplate code for managing the default pinctrl state and
convert into using the new pinctrl_select_default_state().

Cc: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191206170821.29711-7-ulf.hansson@linaro.org

Nowadays sdhci prevents runtime suspend when SDIO IRQs are enabled.

However, some variants such as sdhci-esdhc-imx's, tries to allow runtime
suspend while having the SDIO IRQs enabled, but without supporting remote
wakeups. This support is a bit questionable, especially if the host device
have a PM domain attached that can be power gated, but more importantly,
the code have also become redundant (which was not the case when it was
introduced).

Rather than keeping the redundant code around, let's drop it and leave this
to be revisited later on.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The SD host controller specification defines 3 types software reset:
software reset for data line, software reset for command line and software
reset for all. Software reset for all means this reset affects the entire
Host controller except for the card detection circuit.

In sdhci_runtime_resume_host() we always do a software "reset for all",
which causes the Spreadtrum variant controller to work abnormally after
resuming. To fix the problem, let's do a software reset for the data and
the command part, rather than "for all".

However, as sdhci_runtime_resume() is a common sdhci function and we don't
want to change the behaviour for other variants, let's introduce a new
in-parameter for it. This enables the caller to decide if a "reset for all"
shall be done or not.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Fixes: fb8bd90f ("mmc: sdhci-sprd: Add Spreadtrum's initial host controller")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add HS400 support for iMX7ULP B0.

According to IC suggest, need to clear the STROBE_DLL_CTRL_RESET
before any setting of STROBE_DLL_CTRL register.

USDHC has register bits(bit[27~20] of register STROBE_DLL_CTRL)
for slave sel value. If this register bits value is 0,  it needs
256 ref_clk cycles to update slave sel value. IC suggest to set
bit[27~20] to 0x4, it only need 4 ref_clk cycle to update slave
sel value. This will short the lock time of slave.

i.MX7ULP B0 will need more time to lock the REF and SLV, so change
to add 5us delay.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

On some SoCs such as i.MX7ULP, there is no busfreq
driver, but cpuidle has some levels which may disable
system/bus clocks, so need to add pm_qos to prevent
cpuidle from entering low level idles and make sure
system/bus clocks are enabled when usdhc is active.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Commit 18094430 ("mmc: sdhci-esdhc-imx: add ADMA Length
Mismatch errata fix") involve the fix of ERR004536, but the
fix is incorrect. Double confirm with IC, need to clear the
bit 7 of register 0x6c rather than set this bit 7.
Here is the definition of bit 7 of 0x6c:
    0: enable the new IC fix for ERR004536
    1: do not use the IC fix, keep the same as before

Find this issue on i.MX845s-evk board when enable CMDQ, and
let system in heavy loading.

root@imx8mmevk:~# dd if=/dev/mmcblk2 of=/dev/null bs=1M &
root@imx8mmevk:~# memtester 1000M > /dev/zero &
root@imx8mmevk:~# [  139.897220] mmc2: cqhci: timeout for tag 16
[  139.901417] mmc2: cqhci: ============ CQHCI REGISTER DUMP ===========
[  139.907862] mmc2: cqhci: Caps:      0x0000310a | Version:  0x00000510
[  139.914311] mmc2: cqhci: Config:    0x00001001 | Control:  0x00000000
[  139.920753] mmc2: cqhci: Int stat:  0x00000000 | Int enab: 0x00000006
[  139.927193] mmc2: cqhci: Int sig:   0x00000006 | Int Coal: 0x00000000
[  139.933634] mmc2: cqhci: TDL base:  0x7809c000 | TDL up32: 0x00000000
[  139.940073] mmc2: cqhci: Doorbell:  0x00030000 | TCN:      0x00000000
[  139.946518] mmc2: cqhci: Dev queue: 0x00010000 | Dev Pend: 0x00010000
[  139.952967] mmc2: cqhci: Task clr:  0x00000000 | SSC1:     0x00011000
[  139.959411] mmc2: cqhci: SSC2:      0x00000001 | DCMD rsp: 0x00000000
[  139.965857] mmc2: cqhci: RED mask:  0xfdf9a080 | TERRI:    0x00000000
[  139.972308] mmc2: cqhci: Resp idx:  0x0000002e | Resp arg: 0x00000900
[  139.978761] mmc2: sdhci: ============ SDHCI REGISTER DUMP ===========
[  139.985214] mmc2: sdhci: Sys addr:  0xb2c19000 | Version:  0x00000002
[  139.991669] mmc2: sdhci: Blk size:  0x00000200 | Blk cnt:  0x00000400
[  139.998127] mmc2: sdhci: Argument:  0x40110400 | Trn mode: 0x00000033
[  140.004618] mmc2: sdhci: Present:   0x01088a8f | Host ctl: 0x00000030
[  140.011113] mmc2: sdhci: Power:     0x00000002 | Blk gap:  0x00000080
[  140.017583] mmc2: sdhci: Wake-up:   0x00000008 | Clock:    0x0000000f
[  140.024039] mmc2: sdhci: Timeout:   0x0000008f | Int stat: 0x00000000
[  140.030497] mmc2: sdhci: Int enab:  0x107f4000 | Sig enab: 0x107f4000
[  140.036972] mmc2: sdhci: AC12 err:  0x00000000 | Slot int: 0x00000502
[  140.043426] mmc2: sdhci: Caps:      0x07eb0000 | Caps_1:   0x8000b407
[  140.049867] mmc2: sdhci: Cmd:       0x00002c1a | Max curr: 0x00ffffff
[  140.056314] mmc2: sdhci: Resp[0]:   0x00000900 | Resp[1]:  0xffffffff
[  140.062755] mmc2: sdhci: Resp[2]:   0x328f5903 | Resp[3]:  0x00d00f00
[  140.069195] mmc2: sdhci: Host ctl2: 0x00000008
[  140.073640] mmc2: sdhci: ADMA Err:  0x00000007 | ADMA Ptr: 0x7809c108
[  140.080079] mmc2: sdhci: ============================================
[  140.086662] mmc2: running CQE recovery

Fixes: 18094430 ("mmc: sdhci-esdhc-imx: add ADMA Length Mismatch errata fix")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

After system suspend, CQE is in cqhci_off state, which set the HALT bit, make
CQE in HALT state. If the SoC do not power down the USDHC module, then when
system resume back, this bit keep the same, still set. Though there is a
sdhci reset during sdhci_resume_host(), but this reset do not impact the
CQE part, so need to clear this bit when enable CQE, otherwise CQE will
stuck in the first CMDQ request after system resume back.

Find this issue on NXP i.MX845s-mek board

[  105.919862] mmc2: cqhci: timeout for tag 6
[  105.923965] mmc2: cqhci: ============ CQHCI REGISTER DUMP ===========
[  105.930407] mmc2: cqhci: Caps:      0x0000310a | Version:  0x00000510
[  105.936847] mmc2: cqhci: Config:    0x00001001 | Control:  0x00000001
[  105.943286] mmc2: cqhci: Int stat:  0x00000000 | Int enab: 0x00000006
[  105.949725] mmc2: cqhci: Int sig:   0x00000006 | Int Coal: 0x00000000
[  105.956164] mmc2: cqhci: TDL base:  0x7809b000 | TDL up32: 0x00000000
[  105.962604] mmc2: cqhci: Doorbell:  0x00000040 | TCN:      0x00000000
[  105.969043] mmc2: cqhci: Dev queue: 0x00000000 | Dev Pend: 0x00000000
[  105.975483] mmc2: cqhci: Task clr:  0x00000000 | SSC1:     0x00011000
[  105.981922] mmc2: cqhci: SSC2:      0x00000001 | DCMD rsp: 0x00000000
[  105.988362] mmc2: cqhci: RED mask:  0xfdf9a080 | TERRI:    0x00000000
[  105.994801] mmc2: cqhci: Resp idx:  0x00000000 | Resp arg: 0x00000000
[  106.001240] mmc2: sdhci: ============ SDHCI REGISTER DUMP ===========
[  106.007680] mmc2: sdhci: Sys addr:  0xb2b37800 | Version:  0x00000002
[  106.014120] mmc2: sdhci: Blk size:  0x00000200 | Blk cnt:  0x00000001
[  106.020560] mmc2: sdhci: Argument:  0x00010000 | Trn mode: 0x00000013
[  106.026999] mmc2: sdhci: Present:   0x01f88008 | Host ctl: 0x00000030
[  106.033439] mmc2: sdhci: Power:     0x00000002 | Blk gap:  0x00000080
[  106.039878] mmc2: sdhci: Wake-up:   0x00000008 | Clock:    0x0000000f
[  106.046318] mmc2: sdhci: Timeout:   0x0000008f | Int stat: 0x00000000
[  106.052757] mmc2: sdhci: Int enab:  0x107f4000 | Sig enab: 0x107f4000
[  106.059196] mmc2: sdhci: AC12 err:  0x00000000 | Slot int: 0x00000502
[  106.065635] mmc2: sdhci: Caps:      0x07eb0000 | Caps_1:   0x8000b407
[  106.072075] mmc2: sdhci: Cmd:       0x00000d1a | Max curr: 0x00ffffff
[  106.078514] mmc2: sdhci: Resp[0]:   0x00000900 | Resp[1]:  0x31360181
[  106.084954] mmc2: sdhci: Resp[2]:   0x44473430 | Resp[3]:  0x00450100
[  106.091392] mmc2: sdhci: Host ctl2: 0x00000008
[  106.095836] mmc2: sdhci: ADMA Err:  0x00000000 | ADMA Ptr: 0x7804b208
[  106.102274] mmc2: sdhci: ============================================
[  106.108785] mmc2: running CQE recovery
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The argument "override_active_level" made it possible to
enforce a specific polarity on the write-protect
GPIO line. All callers in the kernel pass "false" to this
call after I have converted all drivers to use GPIO machine
descriptors, so remove the argument and clean out this.

This kind of polarity inversion should be handled by the
GPIO descriptor inside the GPIO library if needed.

This rids us of one instance of the kludgy calls into
the gpiod_get_raw_value() API.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

In case of error, the function devm_kzalloc() returns NULL pointer not
ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.

Fixes: fadac7488064 ("mmc: sdhci-esdhc-imx: add CMDQ support")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Currently, USDHC do not generate transfer complete interrupt
when send a non-data-command with R1b response. But if want
to support DCMD in CMDQ, need to change this, the DCMD IC
logic require the USDHC to enable this function, otherwise
DCMD will never get a CC(command complete) interrupt.

This patch set ESDHC_VEND_SPEC2_EN_BUSY_IRQ and add DCMD support.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add CMDQ support for imx8qm/imx8qxp.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
[Ulf: Rebased on top of latest changes]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add an new esdhc_soc_data for i.MX8QXP, and add HS400_ES mode
support.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
[Ulf: Rebased on top of latest changes]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

For some eMMC, after switch to HS400ES mode, it need to config the strobe
dll target dealy even if the clock is 50MHZ or 25MHz, otherwise will meet
CMD index/crc error when send CMD13 to check the switch status.

[    2.473915] IRQ status 0x000a8001
[    2.473934] mmc2: mmc_select_hs400es failed, error -84
[    2.473938] mmc2: error -84 whilst initialising MMC card
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

It's observed that i.MX uSDHC needed delay between tuning
cycles for HS200 successful tuning. This patch is to set 1ms
delay for that.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

i.MX6ULL has errata ERR010450, point out that due to SOC I/O
timing limitation, for eMMC HS200 and SD/SDIO 3.0 SDR104, the
clock rate can't exceed 150MHz. And for eMMC DDR52 and SD/SDIO
DDR50 mode, the clock rate can't exceed 45MHz.

This patch add this limit for imx6ull.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
[Ulf: Fixed comments and whitespace]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Now tuning reset will be done when the timing is MMC_TIMING_LEGACY/
MMC_TIMING_MMC_HS/MMC_TIMING_SD_HS. But for timing MMC_TIMING_MMC_HS,
we can not do tuning reset, otherwise HS400 timing is not right.

Here is the process of init HS400, first finish tuning in HS200 mode,
then switch to HS mode and 8 bit DDR mode, finally switch to HS400
mode. If we do tuning reset in HS mode, this will cause HS400 mode
lost the tuning setting, which will cause CRC error.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Cc: stable@vger.kernel.org # v4.12+
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: d9370424 ("mmc: sdhci-esdhc-imx: reset tuning circuit when power on mmc card")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

DDR50 tuning is optinally defined in sd 3.0 spec. And i.MX
uSDHC internally already uses a fixed optimized timing for
DDR50, normally does not require tuning for DDR50 mode.

This patch specify a new execute_tuning function for i.MX
uSDHC, do not impact i.MX eSDHC.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The bit ESDHC_STD_TUNING_EN may be configed by bootloader code if it
choose to use standard tuning method. So on linux side, if choose to
use manual tuning method, need to clear the bit ESDHC_STD_TUNING_EN,
remove the impact of bootloader code.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Variant specific driver data doesn't change at run-time, so mark it as
const to reflect that.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Simplify things by making the i.MX SDHCI driver just use
slot GPIO with descriptors instead of passing around the global
GPIO numbers that we want to get rid of.

As it turns out, just one single board is using the platform
data to pass in GPIOs numbers for CD and WP, so we augment this
to use a machine descriptor table instead.

Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The SDHCI_ACMD12_ERR register is used for auto-CMD23 and auto-CMD12
errors, as is the SDHCI_INT_ACMD12ERR interrupt bit. Rename them to
SDHCI_AUTO_CMD_STATUS and SDHCI_INT_AUTO_CMD_ERR respectively.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Fix indent. This also makes disable/enable clock blocks look
alike.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

In the uSDHC case (e.g. i.MX 6) clocks only get disabled if frequency
is set to 0. However, it could be that the stack asks for a frequency
change while clocks are on. In that case the function clears the
divider registers (by clearing ESDHC_CLOCK_MASK) while the clock is
enabled! This causes a short period of time where the clock is
undivided (on a i.MX 6DL a clock of 196MHz has been measured).

For older IP variants the driver disables clock by clearing some bits
in ESDHC_SYSTEM_CONTROL.

Make sure to disable card clock before changing frequency for uSDHC
IP variants too.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The field support_vsel is currently only used in the device tree
case. Get rid of it. No change in behavior.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The uSDHC supports DDR modes for eMMC devices running at 3.3V. This
allows to run eMMC with 3.3V signaling voltage at DDR52 mode:

  # cat /sys/kernel/debug/mmc1/ios
  clock:          52000000 Hz
  vdd:            21 (3.3 ~ 3.4 V)
  bus mode:       2 (push-pull)
  chip select:    0 (don't care)
  power mode:     2 (on)
  bus width:      3 (8 bits)
  timing spec:    8 (mmc DDR52)
  signal voltage: 0 (3.30 V)
  driver type:    0 (driver type B)
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

If pinctrl nodes for 100/200MHz are missing, the controller should
not select any mode which need signal frequencies 100MHz or higher.
To prevent such speed modes the driver currently uses the quirk flag
SDHCI_QUIRK2_NO_1_8_V. This works nicely for SD cards since 1.8V
signaling is required for all faster modes and slower modes use 3.3V
signaling only.

However, there are eMMC modes which use 1.8V signaling and run below
100MHz, e.g. DDR52 at 1.8V. With using SDHCI_QUIRK2_NO_1_8_V this
mode is prevented. When using a fixed 1.8V regulator as vqmmc-supply
the stack has no valid mode to use. In this tenuous situation the
kernel continuously prints voltage switching errors:
  mmc1: Switching to 3.3V signalling voltage failed

Avoid using SDHCI_QUIRK2_NO_1_8_V and prevent faster modes by
altering the SDHCI capability register. With that the stack is able
to select 1.8V modes even if no faster pinctrl states are available:
  # cat /sys/kernel/debug/mmc1/ios
  ...
  timing spec:    8 (mmc DDR52)
  signal voltage: 1 (1.80 V)
  ...

Link: http://lkml.kernel.org/r/20180628081331.13051-1-stefan@agner.chSigned-off-by: Stefan Agner <stefan@agner.ch>
Fixes: ad93220d ("mmc: sdhci-esdhc-imx: change pinctrl state according
to uhs mode")
Cc: <stable@vger.kernel.org> # v4.13+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

While performing R/W access in PIO mode, the common SDHCI driver checks
the buffer ready status once per whole block processing. That is, after
getting an appropriate interrupt, or checking an appropriate status bit,
the driver makes buffer accesses for the whole block size (e.g. 128 reads
for 512 bytes block). This is done in accordance with SD Host Controller
Specification.

At the same time, the Ultra Secured Digital Host Controller (uSDHC), used
in i.MX6 (and, probably, earlier i.MX series too), uses a separate
Watermark Levels register, controlling the amount of data or space
available when raising status bit or interrupt. For default watermark
setting of 16 words, the controller expects (and guarantees) no more
than 16 buffer accesses after raising buffer ready status bit and
generating an appropriate interrupt. If the driver tries to access the
whole block size, it will get incorrect data at the end, and a new
interrupt will appear later, when the driver already doesn't expect it.
This happens sometimes, more likely on low frequencies, e.g. when
reading EXT_CSD at MMC card initialization phase
(which makes that initialization fail).

Such behavior of i.MX uSDHC seems to be non-compliant
to SDHCI Specification, but this is the way it works now.

In order not to rewrite the SDHCI driver PIO mode access logic,
the IMX specific driver can just set the watermark level to default
block size (128 words or 512 bytes), so that the controller behavior
will be consistent to generic specification. This patch does this
for PIO mode accesses only, restoring default values for DMA accesses
to avoid any possible side effects from performance point of view.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Signed-off-by: Harish Jenny K N <harish_kandiga@mentor.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Commit 5143c953 ("mmc: sdhci-esdhc-imx: Allow all supported
prescaler values") made it possible to set SYSCTL.SDCLKFS to 0 in SDR
mode, thus bypassing the SD clock frequency prescaler, in order to be
able to get higher SD clock frequencies in some contexts. However, that
commit missed the fact that this value is illegal on the eSDHCv3
instance of the i.MX53. This seems to be the only exception on i.MX,
this value being legal even for the eSDHCv2 instances of the i.MX53.

Fix this issue by changing the minimum prescaler value if the i.MX53
eSDHCv3 is detected. According to the i.MX53 reference manual, if
DLLCTRL[10] can be set, then the controller is eSDHCv3, else it is
eSDHCv2.

This commit fixes the following issue, which was preventing the i.MX53
Loco (IMX53QSB) board from booting Linux 4.15.0-rc5:
[    1.882668] mmcblk1: error -84 transferring data, sector 2048, nr 8, cmd response 0x900, card status 0xc00
[    2.002255] mmcblk1: error -84 transferring data, sector 2050, nr 6, cmd response 0x900, card status 0xc00
[   12.645056] mmc1: Timeout waiting for hardware interrupt.
[   12.650473] mmc1: sdhci: ============ SDHCI REGISTER DUMP ===========
[   12.656921] mmc1: sdhci: Sys addr:  0x00000000 | Version:  0x00001201
[   12.663366] mmc1: sdhci: Blk size:  0x00000004 | Blk cnt:  0x00000000
[   12.669813] mmc1: sdhci: Argument:  0x00000000 | Trn mode: 0x00000013
[   12.676258] mmc1: sdhci: Present:   0x01f8028f | Host ctl: 0x00000013
[   12.682703] mmc1: sdhci: Power:     0x00000002 | Blk gap:  0x00000000
[   12.689148] mmc1: sdhci: Wake-up:   0x00000000 | Clock:    0x0000003f
[   12.695594] mmc1: sdhci: Timeout:   0x0000008e | Int stat: 0x00000000
[   12.702039] mmc1: sdhci: Int enab:  0x107f004b | Sig enab: 0x107f004b
[   12.708485] mmc1: sdhci: AC12 err:  0x00000000 | Slot int: 0x00001201
[   12.714930] mmc1: sdhci: Caps:      0x07eb0000 | Caps_1:   0x08100810
[   12.721375] mmc1: sdhci: Cmd:       0x0000163a | Max curr: 0x00000000
[   12.727821] mmc1: sdhci: Resp[0]:   0x00000920 | Resp[1]:  0x00000000
[   12.734265] mmc1: sdhci: Resp[2]:   0x00000000 | Resp[3]:  0x00000000
[   12.740709] mmc1: sdhci: Host ctl2: 0x00000000
[   12.745157] mmc1: sdhci: ADMA Err:  0x00000001 | ADMA Ptr: 0xc8049200
[   12.751601] mmc1: sdhci: ============================================
[   12.758110] print_req_error: I/O error, dev mmcblk1, sector 2050
[   12.764135] Buffer I/O error on dev mmcblk1p1, logical block 0, lost sync page write
[   12.775163] EXT4-fs (mmcblk1p1): mounted filesystem without journal. Opts: (null)
[   12.782746] VFS: Mounted root (ext4 filesystem) on device 179:9.
[   12.789151] mmcblk1: response CRC error sending SET_BLOCK_COUNT command, card status 0x900
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Reported-by: Wladimir J. van der Laan <laanwj@gmail.com>
Tested-by: Wladimir J. van der Laan <laanwj@gmail.com>
Fixes: 5143c953 ("mmc: sdhci-esdhc-imx: Allow all supported prescaler values")
Cc: <stable@vger.kernel.org> # v4.13+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>