Merge branch 'perf/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/frederic/random-tracing into perf/urgent

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (47 commits)
  sysctl: net: call unregister_net_sysctl_table where needed
  Revert: veth: remove unneeded ifname code from veth_newlink()
  smsc95xx: fix reset check
  tg3: Fix failure to enable WoL by default when possible
  networking: inappropriate ioctl operation should return ENOTTY
  amd8111e: trivial typo spelling: Negotitate -> Negotiate
  ipv4: don't spam dmesg with "Using LC-trie" messages
  af_unix: Only allow recv on connected seqpacket sockets.
  mii: add support of pause frames in mii_get_an
  net: ftmac100: fix scheduling while atomic during PHY link status change
  usbnet: Transfer of maintainership
  usbnet: add support for some Huawei modems with cdc-ether ports
  bnx2: cancel timer on device removal
  iwl4965: fix "Received BA when not expected"
  iwlagn: fix "Received BA when not expected"
  dsa/mv88e6131: fix unknown multicast/broadcast forwarding on mv88e6085
  usbnet: Resubmit interrupt URB if device is open
  iwl4965: fix "TX Power requested while scanning"
  iwlegacy: led stay solid on when no traffic
  b43: trivial: update module info about ucode16_mimo firmware
  ...

ctl_table_headers registered with register_net_sysctl_table should
have been unregistered with the equivalent unregister_net_sysctl_table
Signed-off-by: Lucian Adrian Grijincu <lucian.grijincu@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

84c49d8c ("veth: remove unneeded
ifname code from veth_newlink()") caused regression on veth
creation. This patch reverts the original one.
Reported-by: Michał Mirosław <mirqus@gmail.com>
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The reset loop check should check the MII_BMCR register value for
BMCR_RESET rather than for MII_BMCR (the register address, which also
happens to be zero).
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: David S. Miller <davem@davemloft.net>

tg3 is supposed to enable WoL by default on adapters which support
that, but it fails to do so unless the adapter's
/sys/devices/.../power/wakeup file contains 'enabled' during the
initialization of the adapter.  Fix that by making tg3 use
device_set_wakeup_enable() to enable wakeup automatically whenever
WoL should be enabled by default.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

ioctl() calls against a socket with an inappropriate ioctl operation
are incorrectly returning EINVAL rather than ENOTTY:

  [ENOTTY]
      Inappropriate I/O control operation.

BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=33992Signed-off-by: Lifeng Sun <lifongsun@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

* 'for-linus' of git://git.infradead.org/ubifs-2.6:
  UBIFS: seek journal heads to the latest bud in replay
  UBIFS: do not free write-buffers when in R/O mode

* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm: (47 commits)
  CLKDEV: Fix clkdev return value for NULL clk case
  ARM: 6891/1: prevent heap corruption in OABI semtimedop
  ARM: kprobes: Tidy-up kprobes-decode.c
  ARM: kprobes: Add emulation of hint instructions like NOP and WFI
  ARM: kprobes: Add emulation of SBFX, UBFX, BFI and BFC instructions
  ARM: kprobes: Add emulation of MOVW and MOVT instructions
  ARM: kprobes: Reject probing of undefined data processing instructions
  ARM: kprobes: Remove redundant code in space_1111
  ARM: kprobes: Fix emulation of PLD instructions
  ARM: kprobes: Reject probing of SETEND instructions
  ARM: kprobes: Consolidate stub decoding functions
  ARM: kprobes: Reject probing of all coprocessor instructions
  ARM: kprobes: Fix emulation of USAD8 instructions
  ARM: kprobes: Fix emulation of SMUAD, SMUSD and SMMUL instructions
  ARM: kprobes: Fix emulation of SXTB16, SXTB, SXTH, UXTB16, UXTB and UXTH instructions
  ARM: kprobes: Reject probing of undefined media instructions
  ARM: kprobes: Add emulation of RBIT instruction
  ARM: kprobes: Reject probing of LDRB instructions which load PC
  ARM: kprobes: Fix emulation of LDRD and STRD instructions
  ARM: kprobes: Reject probing of LDR/STR instructions which update PC unpredictably
  ...

This is the second fix of the following symptom:

UBIFS error (pid 34456): could not find an empty LEB

which sometimes happens after power cuts when we mount the file-system - UBIFS
refuses it with the above error message which comes from the
'ubifs_rcvry_gc_commit()' function. I can reproduce this using the integck test
with the UBIFS power cut emulation enabled.

Analysis of the problem.

Currently UBIFS replay seeks the journal heads to the last _replayed_ bud.
But the buds are replayed out-of-order, so the replay basically seeks journal
heads to the "random" bud belonging to this head, and not to the _last_ one.

The result of this is that the GC head may be seeked to a full LEB with no free
space, or very little free space. And 'ubifs_rcvry_gc_commit()' tries to find a
fully or mostly dirty LEB to match the current GC head (because we need to
garbage-collect that dirty LEB at one go, because we do not have @c->gc_lnum).
So 'ubifs_find_dirty_leb()' fails and we fall back to finding an empty LEB and
also fail. As a result - recovery fails and mounting fails.

This patch teaches the replay to initialize the GC heads exactly to the latest
buds, i.e. the buds which have the largest sequence number in corresponding
log reference nodes.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Cc: stable@kernel.org

Currently UBIFS has a small optimization - it frees write-buffers when it is
re-mounted from R/W mode to R/O mode. Of course, when it is mounted R/O, it
does not allocate write-buffers as well.

This optimization is nice but it leads to subtle problems and complications
in recovery, which I can reproduce using the integck test. The symptoms are
that after a power cut the file-system cannot be mounted if we first mount
it R/O, and then re-mount R/W - 'ubifs_rcvry_gc_commit()' prints:

UBIFS error (pid 34456): could not find an empty LEB

Analysis of the  problem.

When mounting R/W, the reply process sets journal heads to buds [1], but
when mounting R/O - it does not do this, because the write-buffers are not
allocated. So 'ubifs_rcvry_gc_commit()' works completely differently for the
same file-system but for the following 2 cases:

1. mounting R/W after a power cut and recover
2. mounting R/O after a power cut, re-mounting R/W and run deferred recovery

In the former case, we have journal heads seeked to the a bud, in the latter
case, they are non-seeked (wbuf->lnum == -1). So in the latter case we do not
try to recover the GC LEB by garbage-collecting to the GC head, but we just
try to find an empty LEB, and there may be no empty LEBs, so we just fail.
On the other hand, in the former case (mount R/W), we are able to make a GC LEB
(@c->gc_lnum) by garbage-collecting.

Thus, let's remove this small nice optimization and always allocate
write-buffers. This should not make too big difference - we have only 3
of them, each of max. write unit size, which is usually 2KiB. So this is
about 6KiB of RAM for the typical case, and only when mounted R/O.

[1]: Note, currently the replay process is setting (seeking) the journal heads
to _some_ buds, not necessarily to the buds which had been the journal heads
before the power cut happened. This will be fixed separately.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Cc: stable@kernel.org

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ALSA: hda - Fix Realtek's chained fixup checks
  Revert "ALSA: hda - Fix pin-config of Gigabyte mobo"
  ALSA: HDA: Fix automute for Gateway NV79
  ALSA: hda: add beep quirk for Realtek 0x1043:831a
  ALSA: usb-audio - Terratec Aureon 7.1 USB ID as C-Media cm6206 quirks
  ALSA: hda - VIA: Fix notify_aa_path_ctls() invalid issue.
  ALSA - au88x0 - Add buffer bytes constraints

* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
  [S390] irqstats: fix counting of pfault, dasd diag and virtio irqs
  [S390] prng: fix pointer arithmetic

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging:
  hwmon: (twl4030-madc-hwmon) Return proper error if hwmon_device_register fails

* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  i2c-parport: Fix adapter list handling
  i2c-i801: Move device ID definitions to driver

The old code considered valid empty LZMA2 streams to be corrupt.
Note that a typical empty .xz file has no LZMA2 data at all,
and thus most .xz files having no uncompressed data are handled
correctly even without this fix.
Signed-off-by: Lasse Collin <lasse.collin@tukaani.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The check of chained fixup list entry was done against the wrong element.
A stupid mistake during refactoring.

Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

This reverts commit c6b35874.

It turned out that there are different pin configurations for this
PCI SSID, including multi-channel modes.  And more proper fix for
allowing line-out mutes will come up in 2.6.40 tree, so we won't need
this fixup any more there.
Reported-by: Andrew Clayton <andrew@digital-domain.net>
Reported-by: Emmanuel Benisty <benisty.e@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

fib_trie_table() is called during netns creation and
Chromium uses clone(CLONE_NEWNET) to sandbox renderer process.

Don't print anything.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This fixes the following oops discovered by Dan Aloni:
> Anyway, the following is the output of the Oops that I got on the
> Ubuntu kernel on which I first detected the problem
> (2.6.37-12-generic). The Oops that followed will be more useful, I
> guess.

>[ 5594.669852] BUG: unable to handle kernel NULL pointer dereference
> at           (null)
> [ 5594.681606] IP: [<ffffffff81550b7b>] unix_dgram_recvmsg+0x1fb/0x420
> [ 5594.687576] PGD 2a05d067 PUD 2b951067 PMD 0
> [ 5594.693720] Oops: 0002 [#1] SMP
> [ 5594.699888] last sysfs file:

The bug was that unix domain sockets use a pseduo packet for
connecting and accept uses that psudo packet to get the socket.
In the buggy seqpacket case we were allowing unconnected
sockets to call recvmsg and try to receive the pseudo packet.

That is always wrong and as of commit 7361c36c the pseudo
packet had become enough different from a normal packet
that the kernel started oopsing.

Do for seqpacket_recv what was done for seqpacket_send in 2.5
and only allow it on connected seqpacket sockets.

Cc: stable@kernel.org
Tested-by: Dan Aloni <dan@aloni.org>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use a standard list with proper locking to handle the list of
adapters. Thankfully it only matters on systems with more than one
parallel port, which are very rare.

Thanks to Lukasz Kapiec for reporting the problem to me.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org

Move the SMBus device ID definitions of recent devices from pci_ids.h
to the i2c-i801.c driver file. They don't have to be shared, as they
are clearly identified and only used in this driver. In the future,
such IDs will go to i2c-i801 directly. This will make adding support
for new devices much faster and easier, as it will avoid cross-
subsystem patch sets and merge conflicts.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Seth Heasley <seth.heasley@intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>

The driver did not return an error if the call to hwmon_device_register failed.
Fix by returning the error reported from hwmon_device_register.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>

* 'fixes-2.6.39' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
  workqueue: fix deadlock in worker_maybe_bind_and_lock()
  workqueue: Document debugging tricks

Fix up trivial spelling conflict in kernel/workqueue.c

clkdev may incorrectly cause a clkdev entry with a NULL clk to return
-ENOENT.  This is not the intention of this code; -ENOENT should only
be returned if the clock entry can not be found in the table.  Fix
this.
Reported-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
  [SCSI] pmcraid: reject negative request size
  [SCSI] put stricter guards on queue dead checks
  [SCSI] scsi_dh: fix reference counting in scsi_dh_activate error path
  [SCSI] mpt2sas: prevent heap overflows and unchecked reads

Merge branch 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  perf, x86, nmi: Move LVT un-masking into irq handlers
  perf events, x86: Work around the Nehalem AAJ80 erratum
  perf, x86: Fix BTS condition
  ftrace: Build without frame pointers on Microblaze

Merge branch 'timer-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'timer-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  hrtimer: Initialize CLOCK_ID to HRTIMER_BASE table statically
  rtc: max8925: Call dev_set_drvdata before rtc_device_register

Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86: ce4100: Configure IOAPIC pins for USB and SATA to level type
  x86: devicetree: Configure IOAPIC pin only once
  x86, setup: When probing memory with e801, use ax/bx as a pair

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  hwmon: (lm85) Fix error paths in probe function
  hwmon: (lm85) Add missing list terminators
  hwmon: (adm1021) Clarify documentation regarding Xeon processors
  hwmon: (lm90) Fix update interval information in driver documentation
  hwmon: (lm90) Add support for ADT7461A and NCT1008

Add support of pause frames advertise in mii_get_an. This provides all drivers
that use mii_ethtool_gset to represent their own and Link partner flow control
abilities in ethtool.
Signed-off-by: Artem Polyakov <artpol84@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Adam Jaremko <adam.jaremko@gmail.com>
Acked-by: Po-Yu Chuang <ratbert@faraday-tech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Somebody has to do it, however unfortunate be the cause.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some newer Huawei devices (T-Mobile Rocket, others) have cdc-ether
compatible ports, so recognize and expose them.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

This oops was recently reported to me:

invalid opcode: 0000 [#1] SMP
last sysfs file:
/sys/devices/pci0000:00/0000:00:01.0/0000:01:0d.0/0000:02:05.0/device
CPU 1
Modules linked in: bnx2(+) sunrpc ipv6 dm_mirror dm_region_hash dm_log sg
microcode serio_raw amd64_edac_mod edac_core edac_mce_amd k8temp i2c_piix4
shpchp ext4 mbcache jbd2 sd_mod crc_t10dif mptsas mptscsih mptbase
scsi_transport_sas radeon ttm drm_kms_helper drm hwmon i2c_algo_bit i2c_core
dm_mod [last unloaded: bnx2]

Modules linked in: bnx2(+) sunrpc ipv6 dm_mirror dm_region_hash dm_log sg
microcode serio_raw amd64_edac_mod edac_core edac_mce_amd k8temp i2c_piix4
shpchp ext4 mbcache jbd2 sd_mod crc_t10dif mptsas mptscsih mptbase
scsi_transport_sas radeon ttm drm_kms_helper drm hwmon i2c_algo_bit i2c_core
dm_mod [last unloaded: bnx2]
Pid: 23900, comm: pidof Not tainted 2.6.32-130.el6.x86_64 #1 BladeCenter LS21
-[797251Z]-
RIP: 0010:[<ffffffffa058b270>]  [<ffffffffa058b270>] 0xffffffffa058b270
RSP: 0018:ffff880002083e48  EFLAGS: 00010246
RAX: ffff880002083e90 RBX: ffff88007ccd4000 RCX: 0000000000000000
RDX: 0000000000000100 RSI: dead000000200200 RDI: ffff8800007b8700
RBP: ffff880002083ed0 R08: ffff88000208db40 R09: 0000022d191d27c8
R10: 0000000000000000 R11: 0000000000000000 R12: ffff8800007b9bc8
R13: ffff880002083e90 R14: ffff8800007b8700 R15: ffffffffa058b270
FS:  00007fbb3bcf7700(0000) GS:ffff880002080000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000001664a98 CR3: 0000000060395000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process pidof (pid: 23900, threadinfo ffff8800007e8000, task ffff8800091c0040)
Stack:
 ffffffff81079f77 ffffffff8109e010 ffff88007ccd5c20 ffff88007ccd5820
<0> ffff88007ccd5420 ffff8800007e9fd8 ffff8800007e9fd8 0000010000000000
<0> ffff88007ccd5020 ffff880002083e90 ffff880002083e90 ffffffff8102a00d
Call Trace:
 <IRQ>
 [<ffffffff81079f77>] ? run_timer_softirq+0x197/0x340
 [<ffffffff8109e010>] ? tick_sched_timer+0x0/0xc0
 [<ffffffff8102a00d>] ? lapic_next_event+0x1d/0x30
 [<ffffffff8106f737>] __do_softirq+0xb7/0x1e0
 [<ffffffff81092cc0>] ? hrtimer_interrupt+0x140/0x250
 [<ffffffff81185f90>] ? filldir+0x0/0xe0
 [<ffffffff8100c2cc>] call_softirq+0x1c/0x30
 [<ffffffff8100df05>] do_softirq+0x65/0xa0
 [<ffffffff8106f525>] irq_exit+0x85/0x90
 [<ffffffff814e3340>] smp_apic_timer_interrupt+0x70/0x9b
 [<ffffffff8100bc93>] apic_timer_interrupt+0x13/0x20
 <EOI>
 [<ffffffff81211ba5>] ? selinux_file_permission+0x45/0x150
 [<ffffffff81262a75>] ? _atomic_dec_and_lock+0x55/0x80
 [<ffffffff812050c6>] security_file_permission+0x16/0x20
 [<ffffffff811861c1>] vfs_readdir+0x71/0xe0
 [<ffffffff81186399>] sys_getdents+0x89/0xf0
 [<ffffffff8100b172>] system_call_fastpath+0x16/0x1b

It occured during some stress testing, in which the reporter was repeatedly
removing and modprobing the bnx2 module while doing various other random
operations on the bnx2 registered net device.  Noting that this error occured on
a serdes based device, we noted that there were a few ethtool operations (most
notably self_test and set_phys_id) that have execution paths that lead into
bnx2_setup_serdes_phy.  This function is notable because it executes a mod_timer
call, which starts the bp->timer running.  Currently bnx2 is setup to assume
that this timer only nees to be stopped when bnx2_close or bnx2_suspend is
called.  Since the above ethtool operations are not gated on the net device
having been opened however, that assumption is incorrect, and can lead to the
timer still running after the module has been removed, leading to the oops above
(as well as other simmilar oopses).

Fix the problem by ensuring that the timer is stopped when pci_device_unregister
is called.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Reported-by: Hushan Jia <hjia@redhat.com>
CC: Michael Chan <mchan@broadcom.com>
CC: "David S. Miller" <davem@davemloft.net>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Need to use broadcast sta_id for management frames, otherwise we broke
BA session in the firmware and get messages like that:

"Received BA when not expected"

or (on older kernels):

"BA scd_flow 0 does not match txq_id 10"

This fix regression introduced in 2.6.35 during station management
code rewrite by:

commit 2a87c26b
Author: Johannes Berg <johannes.berg@intel.com>
Date:   Fri Apr 30 11:30:45 2010 -0700

    iwlwifi: use iwl_find_station less
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Need to use broadcast sta_id for management frames, otherwise we broke
BA session in the firmware and get messages like that:

"Received BA when not expected"

or (on older kernels):

"BA scd_flow 0 does not match txq_id 10"

This fix regression introduced in 2.6.35 during station management
code rewrite by:

commit 2a87c26b
Author: Johannes Berg <johannes.berg@intel.com>
Date:   Fri Apr 30 11:30:45 2010 -0700

    iwlwifi: use iwl_find_station less

Patch partially resolve:
https://bugzilla.kernel.org/show_bug.cgi?id=16691
However, there are still 11n performance problems on 4965 and 5xxx
devices that need to be investigated.

Cc: stable@kernel.org # 2.6.35+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

If a rescuer and stop_machine() bringing down a CPU race with each
other, they may deadlock on non-preemptive kernel.  The CPU won't
accept a new task, so the rescuer can't migrate to the target CPU,
while stop_machine() can't proceed because the rescuer is holding one
of the CPU retrying migration.  GCWQ_DISASSOCIATED is never cleared
and worker_maybe_bind_and_lock() retries indefinitely.

This problem can be reproduced semi reliably while the system is
entering suspend.

 http://thread.gmane.org/gmane.linux.kernel/1122051

A lot of kudos to Thilo-Alexander for reporting this tricky issue and
painstaking testing.

stable: This affects all kernels with cmwq, so all kernels since and
        including v2.6.36 need this fix.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Thilo-Alexander Ginkel <thilo@ginkel.com>
Tested-by: Thilo-Alexander Ginkel <thilo@ginkel.com>
Cc: stable@kernel.org